Damage Evolution of Ballastless Track Concrete Exposed to Flexural Fatigue Loads:The Application of Ultrasonic Pulse Velocity,Impact-echo and Surface Electrical Resistance Method

In order to clarify the fatigue damage evolution of concrete exposed to flexural fatigue loads,ultrasonic pulse velocity(UPV),impact-echo technology and surface electrical resistance(SR) method were used.Damage variable based on the change of velocity of ultrasonic pulse(Du) and impact elastic wave(Di)were defined according to the classical damage theory.The influences of stress level,loading frequency and concrete strength on damage variable were measured.The experimental results show that Du and Di both present a three-stages trend for concrete exposed to fatigue loads.Since impact elastic wave is more sensitive to the microstructure damage in stage Ⅲ,the critical damage variable,i e,the damage variable before the final fracture of concrete of Di is slightly higher than that of Du.Meanwhile,the evolution of SR of concrete exposed to fatigue loads were analyzed and the relationship between SR and Du,SR and Di of concrete exposed to fatigue loads were established.It is found that the SR of concrete was decreased with the increasing fatigue cycles,indicating that surface electrical resistance method can also be applied to describe the damage of ballastless track concrete exposed to fatigue loads.

Fatigue Resistance of RCA Modified Asphalt Based on Dielectric Properties

In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.

Cellular models of stress resistance may pave ways to fight neurodegenerative diseases

Alzheimer's disease(AD),the most common form of neurodegeneration,is characterized by selective neuronal vulnerability and brain regionselective neuron demise.The entorhinal cortex and hippoc,ampal CA1 projection neurons are at greater risk in AD whereas other regions display resistance to neurodegeneration.Interestingly,the cerebellum,a phylogenetically very old region,is affected only very late in the disease progression.

Influence of masticatory fatigue on the fracture resistance of the pulpless teeth restored with quartz-fiber post-core and crown

To investigate whether masticatory fatigue affects the fracture resistance and pattern of lower premolars restored with quartz-fiber post-core and full crown, 44 single rooted lower premolars recently extracted from orthodontic patients were divided into two groups of 22 each. The crowns of all teeth were removed and endodontically treated and then restored with quartz-fiber post-core and full crown. Twenty-two teeth in one group were selected randomly and circularly loaded at 45° to the long axis of the teeth of 127.4 N at a 6 Hz frequency, and the other group was not delivered to cyclic loading and considered as control. Subsequently, all teeth in two groups were continually loaded to fail at 45° to the long axis of the teeth at a crosshead speed of 1 mm.min-1. The mean destructive force values were （733.88±254.99） and （869.14±280.26） N for the experimental and the control group, respectively, and no statistically significant differences were found between two groups （P〉O.05）. Bevel fracture and horizontal fracture in the neck of root were the major fracture mode of the specimens. Under the circumstances of this study, it seems that cyclic loading does not affect the fracture strength and pattern of the quartz-fiber post-core-crown complex.

Overall Evaluation of the Effect of Residual Stress Induced by Shot Peening in the Improvement of Fatigue Fracture Resistance for Metallic Materials

Before 1980s,the circular suspension spring in automobile subjected to torsion fatigue load,under the cyclic normal tensile stresses,the majority of fatigue fracture occurred was in normal tensile fracture mode（NTFM）and the fracture surface was under 45°diagonal.Because there exists the interaction between the residual stresses induced by shot peening and the applied cyclic normal tensile stresses in NTFM,which represents as＂stress strengthening mechanism＂,shot peening technology could be used for improving the fatigue fracture resistance（FFR）of springs.However,since 1990s up to date,in addition to regular NTFM,the fatigue fractures occurred of peened springs from time to time are in longitudinal shear fracture mode（LSFM）or transverse shear fracture mode（TSFM）with the increase of applied cyclic shear stresses,which leads to a remarkable decrease of FFR.However,LSFM/TSFM can be avoided effectively by means of shot peening treatment again on the peened springs.The phenomena have been rarely happened before.At present there are few literatures concerning this problem.Based upon the results of force analysis of a spring,there is no interaction between the residual stresses by shot peening and the applied cyclic shear stresses in shear fracture.This;means that the effect of＂stress strengthening mechanism＂for improving the FFR of LSFM/TSFM is disappeared basically.During shot peening,however,both of residual stress and cyclic plastic deformed microstructure are induced synchronously like＂twins＂in the surface layer of a spring.It has been found for the first time by means of force analysis and experimental results that the modified microstructure in the＂twins＂as a＂structure strengthening mechanism＂can improve the FFR of LSFM/TSFM.At the same time,it is;also shown that the optimum technology of shot peening strengthening must have both＂stress strengthening mechanism＂and＂structure strengthening mechanism＂simultaneously so that the FFR of both NTFM and LSFM/TSFM can be improved by shot peening.

Fatigue Resistance of Filled NR with PMMA-Wrapped and Rare Earth-Doped Alumina-Siloxane Gel

Poly (methyl methacrylate) (PMMA) was used to wrap alumina-siloxane sol which was produced by water glass, aluminum nitrate and α-methacrylic acid, and as a result, alumina-siloxane gel wrapped by PMMA was obtained. Meanwhile, rare earth ions were employed to dope in the course of reaction, and the formed rare earth doped PMMA microcapsule powder was filled into natural rubber (NR). It is found through the analysis of mechanical properties that Young′s modulus universally improves and a remarkable resistance to fatigue is displayed. Retention rate of tensile strength is twice that of the controlled sample after ten thousand times of extension fatigue.

Fatigue Resistance and Failure Behavior of Penetration and Non-Penetration Laser Welded Lap Joints

Penetration and non-penetration lap laser welding is the joining method for assembling side facade panels of railway passenger cars,while their fatigue performances and the difference between them are not completely understood.In this study,the fatigue resistance and failure behavior of penetration 1.5+0.8-P and non-penetration 0.8+1.5-N laser welded lap joints prepared with 0.8 mm and 1.5 mm cold-rolled 301L plates were investigated.The weld beads showed a solidification microstructure of primary ferrite with good thermal cracking resistance,and their hardness was lower than that of the plates.The 1.5+0.8-P joint exhibited better fatigue resistance to low stress amplitudes,whereas the 0.8+1.5-N joint showed greater resistance to high stress amplitudes.The failure modes of 0.8+1.5-N and 1.5+0.8-P joints were 1.5 mm and 0.8 mm lower lap plate fracture,respectively,and the primary cracks were initiated at welding fusion lines on the lap surface.There were long plastic ribs on the penetration plate fracture,but not on the non-penetration plate fracture.The fatigue resistance stresses in the crack initiation area of the penetration and non-penetration plates calculated based on the mean fatigue limits are 408 MPa and 326 MPa,respectively,which can be used as reference stress for the fatigue design of the laser welded structures.The main reason for the difference in fatigue performance between the two laser welded joints was that the asymmetrical heating in the non-penetration plate thickness resulted in higher residual stress near the welding fusion line.

Effect of Microstructure on Impact Fatigue Resistance and Impact Wear Resistance of Medium Cr-Si Cast Iron

A great amount of iron grinding balls in tube mills have been consumed. Under this impact abrasive wear working condition, the failure of wear resistant alloying white irons grinding balls is mainly caused by fatigue spalling. The impact wear resistance of martensitic high chromium cast iron （Cr of 15%） is not high sometimes, but its cost is not low. Thus, medium Cr-Si wear resistant cast iron is recommended. The influence of the iron on impact fatigue resistance and impact wear resistance is pronounced. Ball-on-ball impact fatigue test and high stress impact wear test of the grinding balls have been carried out. The results show that the impact fatigue resistance （IFR） and impact wear resistance （IWR） of medium Cr-Si cast iron are superior to those of martensitic high chromium cast iron （Cr of 15%）. The main reasons are that （1） the stress in medium Cr-Si cast iron is released in the as-cast state; （2） the matrix is fine pearlite with better toughness and plasticity; （3） the pearlite is more stable compared with a retained austenite under repeated impact load and less phase transformation can take place; （4） high silicon content im- proves the morphology of eutectic carbide; （5） there is no seeondary carbide which results in less crack sources. All these factors are beneficial to improvement of impact fatigue spalling resistance. The eutectic carbide M7C3 is the main constituent to resist wear.

A preliminary study on the anti-inflammatory and analgesic effects of two extracts of pine pollen on anoxia and fatigue resistance

Background:To study the anti-inflammatory,analgesic,fatigue resistant and antihypoxia effects of ethanol extract and water extract of pine pollen.Methods:Two different extracts of pine pollen were prepared into there different concentrations,that is 1.5 mg·mL^-1,4.5 mg·mL^-1 and 7.5 mg·mL^-1 respectively.The extract were studied by xylene-induced ear swelling,acetic acid distortion test and hot plate test.The antihypoxia and antifatigue effects were explored by weight-bearing swimming experiment,routine pressure hypoxia tolerance experiment and liver weight coefficient comparison.Results:Through the study of the four pharmacological effects of ethanol extract and water extract,we found that the anti-inflammatory,analgesic,antithyposia and antifatigue effects of ethanol extract were better than that of water extract.Moreover,the experimental effects significantly improved with the increase of the concentration,and the effect of alcohol increased dose group was accurate(P<0.05).Conclusion:Pine pollen has excellent effects of anti-inflammatory,analgesic,antihypoxia and anti-fatigue.Besides,with the increase of drug concentration,effects tend to be more obvious with positive correlation.

Influence of surface coating on Ti811 alloy resistance to fretting fatigue at elevated temperature

An extensive study of the composition distribution, bonding strength, hardness, and wear resistance of a 0Cr18Ni9 film deposited on a Ti811 titanium alloy surface by ion beam enhanced deposition （IBED） is presented. Shot peening was introduced to post-treat the modified surface to synergistically improve the fretting fatigue resistance of the Ti811 alloy at 350°C. The results indicate that the 0Cr18Ni9 film with high density, small grain size, low void radio, and high bonding strength can be prepared using IBED. As a result, the hardness, wear resistance, and fretting fatigue resistance of the Ti811 alloy are increased to a remarkable extent. Compared with shot peening treatment or IBED 0Cr18Ni9 film alone, the Ti811 titanium alloy with an IBED 0Cr18Ni9 film combined with shot peening shows a higher fretting fatigue resistance at 350°C. This is due to the synergistic effect of the high wear resistance of the film surface and the residual compressive stress induced by shot peening.

Process Evaluation, Tensile Properties and Fatigue Resistance of Chopped and Continuous Fiber Reinforced Thermoplastic Composites by 3D Printing

The aim of this article was to comprehensively evaluate the manufacturing process,tensile properties and fatigue resistance of the chopped and continuous fiber reinforced thermoplastic composites(CFRTPCs)by 3D printing.The main results included:the common defects of the printed CFRTPCs contained redundant and accumulation defects,scratch and warping defects;the continuous fiber contributed to the dimensional stability and accuracy of width and thickness;associations between mass percentage of fiber reinforcement and the averages of elastic mod-ulus,strain at break and ultimate tensile strength were approximately linear based on tensile test results;the fati-gue resistance improved with the increasing fiber reinforcement based on fatigue test results.As for specimens with four fiber rings,there was a good linear relationship between the stress level and logarithm value of cycles during the whole life while those of pure matrix and specimens with one and two fiber rings were piecewise linear,taking about 10,000 cycles as boundary.The micro morphology showed that the fatigue failure behaved as matrix fracture,large and small fiber bundles and single fibers extracted from matrix.Under the tension-tension fatigue load,the deformations where easily concentrating stress behaved as sunken surfaces along thickness and width directions,and the deformation along width direction was greater than that along thickness direction.

Quality Evaluation of Diffusion Bonded Joints by Electrical Resistance Measuring and Microscopic Fatigue Testing

Micro-structure related behavior of diffusion bonding joints is a crucial issue in device and reactor fabrication of Micro Chemo Mechanical Systems.However,the previous studies have been focused on the macro mechanical performance of diffusion bonded joint,especially diffusion bonding conditions effects on tensile strength,shearing strength and fatigue strength.The research of interfacial micro-voids and microstructures evolution for failure mechanism has not been carried out for diffusion-bonded joints.An interfacial electrical resistance measuring method is proposed to evaluate the quality of bonded joints and verified by using two-dimensional finite-element simulation.The influences of micro void geometry on increments of resistance are analyzed and the relationship between bonded area fraction and resistance increment is established by theoretical analysis combined with simulated results.Metallographic inspections and micro-hardness testing are conducted near the interface of diffusion bonded joints.For the purpose of identifying the failure mechanisms of the joints,both microscopic tensile and fatigue tests are conducted on the self-developed in-situ microscopic fatigue testing system.Based on the microscopic observations,the mechanism of interfacial failure is addressed.The observation result shows that for 316LSS diffusion-bonded joints,microstructure evolution and effect of micro-voids play a key role in interfacial failure mechanism.Finally,a new life prediction model in terms of the increment of electrical resistance is developed and confirmed by the experimental results.The proposed study is initiated that constituted a primary interfacial failure mechanism on micron scale and provide the life prediction for reliability of components sealed by diffusion bonding.

Study on the Thermal Fatigue Behavior of Hot Deformed Wear Resistance Cast Iron and Effect of Carbide

The thermal fatigue behavior of wear resistance cast iron with different quantity of deformation has been investigated. The results show that eutectic carbide is the main location and passage for initiation and extension of thermal fatigue cracks, approving that the more serious, the carbide breaks. The higher thermal fatigue resistance of wear resistance cast iron will be and thermal fatigue fracture belongs mainly to brittleness.

Study of Thermal Fatigue Resistance of a Composite Coating Made by a Vacuum Fusion Sintering Method

Thermal fatigue behavior of a Ni base alloy chromium carbide composite coating made by a vacuum fusion sintering method are discussed. Results show that thermal fatigue behavior is associated with cyclic upper temperature and coating thickness. As the thickness of the coating decreases, the thermal fatigue resistance increases. The thermal fatigue resistance cuts down with the thermal cyclic upper temperature rising. The crack growth rate decreases with the increase in cyclic number until crack arrests. Thermal fatigue failure was not found along the interface of the coating/matrix. The tract of thermal fatigue crack cracks along the interfaces of phases.

Investigating the Effect of Fatigue on Fracturing Resistance of Rocks

There is no doubt that an understanding of brittle rock fracturing is a key element in the solution of many engineering problems that involve rock structures. Some rock structures such as bridge and dam abutments and foundations, and tunnel walls, undergo both static and cyclic loading caused by drilling and blasting, and vehicle-induced vibrations. This type of loading often causes rock to fail at a lower than its static strength due to the effect of rock fatigue. A series of laboratory diametrical compression tests was performed on Brisbane tuff disc specimens to investigate their mode-I fracture toughness response to static and cyclic loading, as a function of the applied load. Both the static and cyclic loading tests were carried out on CCNBD （cracked chevron notched Brazilian disc） rock specimens. In the tests described herein, the reduction in fracture toughness under dynamic cyclic loading was found to be up to 48% of the static fracture toughness. Contrary to the static tests, the cyclic tests produced much more crushed material in front of the tip of the chevron notched crack.

The influence of resistance exercise training prescription variables on skeletal muscle mass,strength,and physical function in healthy adults:An umbrella review

Purpose:The aim of this umbrella review was to determine the impact of resistance training(RT)and individual RT prescription variables on muscle mass,strength,and physical function in healthy adults.Methods:Following Preferred Reporting Items for Systematic Reviews and Meta-Analyses(PRISMA)guidelines,we systematically searched and screened eligible systematic reviews reporting the effects of differing RT prescription variables on muscle mass(or its proxies),strength,and/or physical function in healthy adults aged>18 years.Results:We identified 44 systematic reviews that met our inclusion criteria.The methodological quality of these reviews was assessed using A Measurement Tool to Assess Systematic Reviews;standardized effectiveness statements were generated.We found that RT was consistently a potent stimulus for increasing skeletal muscle mass(4/4 reviews provide some or sufficient evidence),strength(4/6 reviews provided some or sufficient evidence),and physical function(1/1 review provided some evidence).RT load(6/8 reviews provided some or sufficient evidence),weekly frequency(2/4 reviews provided some or sufficient evidence),volume(3/7 reviews provided some or sufficient evidence),and exercise order(1/1 review provided some evidence)impacted RT-induced increases in muscular strength.We discovered that 2/3 reviews provided some or sufficient evidence that RT volume and contraction velocity influenced skeletal muscle mass,while 4/7 reviews provided insufficient evidence in favor of RT load impacting skeletal muscle mass.There was insufficient evidence to conclude that time of day,periodization,inter-set rest,set configuration,set end point,contraction velocity/time under tension,or exercise order(only pertaining to hypertrophy)influenced skeletal muscle adaptations.A paucity of data limited insights into the impact of RT prescription variables on physical function.Conclusion:Overall,RT increased muscle mass,strength,and physical function compared to no exercise.RT intensity(load)and weekly frequency impacted RT-induced increases in muscular strength but not muscle hypertrophy.RT volume(number of sets)influenced muscular strength and hypertrophy.

Frequency Domain Fatigue Evaluation on SCR Girth-Weld Based on Structural Stress

The Steel Catenary Riser(SCR)is a vital component for transporting oil and gas from the seabed to the floating platform.The harsh environmental conditions and complex platform motion make the SCR’s girth-weld prone to fatigue failure.The structural stress fatigue theory and Master S-N curve method provide accurate predictions for the fatigue damage on the welded joints,which demonstrate significant potential and compatibility in multi-axial and random fatigue evaluation.Here,we propose a new frequency fatigue model subjected to welded joints of SCR under multiaxial stress,which fully integrates the mesh-insensitive structural stress and frequency domain random process and transforms the conventional welding fatigue technique of SCR into a spectrum analysis technique utilizing structural stress.Besides,a full-scale FE model of SCR with welds is established to obtain the modal structural stress of the girth weld and the frequency response function(FRF)of modal coordinate,and a biaxial fatigue evaluation about the girth weld of the SCR can be achieved by taking the effects of multi-load correlation and pipe-soil interaction into account.The research results indicate that the frequency-domain fatigue results are aligned with the time-domain results,meeting the fatigue evaluation requirements of the SCR.

Impact of comorbid subthreshold depressive symptoms on cancerrelated fatigue and complications in adults with leukemia

BACKGROUND Patients not only experience symptoms caused by cancer but also suffer from the accompanying psychological pain.Therefore,these patients do not have high quality of life.According to the World Health Organization,the incidence of leukemia in China in 2020 was 5.1/100000,the mortality rate was 3.3/100000,and the prevalence rate was 16.7/100000.Therefore,it is important to examine the influence of comorbid subthreshold depressive symptoms on leukemia patients.AIM To determine the impact of comorbid subthreshold depressive symptoms on cancer-related fatigue and complications in leukemia patients,thereby providing a basis for early diagnosis and treatment in clinical practice.METHODS A questionnaire survey was conducted among leukemia patients admitted to a tertiary hospital in Xi'an,Shaanxi Province,China,from August 2022 to December 2023.Patients with a score>16 on the Chinese Classification of Mental Disorders(CCMD-3)and a Hamilton Depression Rating Scale score of 8-17 were classified as the subthreshold depressive group(n=95),while 100 leukemia patients admitted during the same period were classified as the control group.Data were collected using Epidata 3.1 software,and comparisons were made between the two groups regarding general clinical data,the Piper Fatigue Scale(PFS),the Pittsburgh Sleep Quality Index(PSQI),the Numeric Rating Scale for pain assessment,laboratory indicators,and the occurrence of complications.RESULTS In this survey,120 leukemia patients with depression were preliminarily screened,95 patients with subthreshold depression were ultimately selected as the subthreshold depression group,and 100 leukemia patients admitted during the same period were enrolled as the normal group.Comparison of basic clinical data between the two groups revealed no significant differences in age,sex,body mass index,cognitive function,or comorbidity with other chronic diseases.However,there were statistically significant differences in the use of radiotherapy and regular exercise between the two groups(P<0.05).Comparisons of scales and laboratory indicators revealed no significant differences in albumin or PSQI scores between the two groups,but there were statistically significant differences in pain scores,PSQI scores,PFS scores,hemoglobin levels,and C-reactive protein levels(P<0.05).Spearman’s correlation analysis indicated that cancer-related fatigue was correlated with age,hemoglobin levels,C-reactive protein levels,pain,and regular exercise among leukemia patients with subthreshold depression.Multivariate regression analysis revealed that advanced age,combined radiotherapy,pain,and low hemoglobin levels were risk factors for cancer-related fatigue in leukemia patients with comorbid subthreshold depression,while regular exercise was a protective factor against cancer-related fatigue.Follow-up comparisons revealed a significantly lower overall incidence of complications in the control group(4%)than in the depressive group(24.21%;P<0.001).CONCLUSION Leukemia patients with comorbid subthreshold depressive symptoms experience more severe cancer-related fatigue and a higher incidence of complications.These findings may be related to advanced age,combined radiotherapy,pain,and low hemoglobin levels,while regular exercise may effectively alleviate symptoms.

Reversal of tamoxifen resistance by artemisinin in ER+breast cancer:bioinformatics analysis and experimental validation

Breast cancer is the leading cause of cancer-related deaths in women worldwide,with Hormone Receptor(HR)+being the predominant subtype.Tamoxifen(TAM)serves as the primary treatment for HR+breast cancer.However,drug resistance often leads to recurrence,underscoring the need to develop new therapies to enhance patient quality of life and reduce recurrence rates.Artemisinin(ART)has demonstrated efficacy in inhibiting the growth of drug-resistant cells,positioning art as a viable option for counteracting endocrine resistance.This study explored the interaction between artemisinin and tamoxifen through a combined approach of bioinformatics analysis and experimental validation.Five characterized genes(ar,cdkn1a,erbb2,esr1,hsp90aa1)and seven drug-disease crossover genes(cyp2e1,rorc,mapk10,glp1r,egfr,pgr,mgll)were identified using WGCNA crossover analysis.Subsequent functional enrichment analyses were conducted.Our findings confirm a significant correlation between key cluster gene expression and immune cell infiltration in tamoxifen-resistant and-sensitized patients.scRNA-seq analysis revealed high expression of key cluster genes in epithelial cells,suggesting artemisinin’s specific impact on tumor cells in estrogen receptor(ER)-positive BC tissues.Molecular target docking and in vitro experiments with artemisinin on LCC9 cells demonstrated a reversal effect in reducing migratory and drug resistance of drug-resistant cells by modulating relevant drug resistance genes.These results indicate that artemisinin could potentially reverse tamoxifen resistance in ER-positive breast cancer.