Analysis on the fault characteristics of three-phase short-circuit for half-wavelength AC transmission lines

Half-wavelength AC transmission(HWACT) is an ultra-long distance AC transmission technology, whose electrical distance is close to half-wavelength at the system power frequency. It is very important for the construction and operation of HWACT to analyze its fault features and corresponding protection technology. In this paper, the steady-state voltage and current characteristics of the bus bar and fault point and the steady-state overvoltage distribution along the line will be analyzed when a three-phase symmetrical short-circuit fault occurs on an HWACT line. On this basis, the threephase fault characteristics for longer transmission lines are also studied.

GENERATOR VIBRATION FAULT DIAGNOSIS METHOD BASED ON ROTOR VIBRATION AND STATOR WINDING PARALLEL BRANCHES CIRCULATING CURRENT CHARACTERISTICS

Rotor vibration characteristics are first analyzed, which are that the rotor vibration of fundamental frequency will increase due to rotor winding inter-turn short circuit fault, air-gap dynamic eccentricity fault, or imbalance fault, and the vibration of the second frequency will increase when the air-gap static eccentricity fault occurs. Next, the characteristics of the stator winding parallel branches circulating current are analyzed, which are that the second harmonics circulating current will increase when the rotor winding inter-turn short circuit fault occurs, and the fundamental circulating current will increase when the air-gap eccentricity fault occurs, neither being strongly affected by the imbalance fault. Considering the differences of the rotor vibration and circulating current characteristics caused by different rotor faults, a method of generator vibration fault diagnosis, based on rotor vibration and circulating current characteristics, is developed. Finally, the rotor vibration and circulating current of a type SDF-9 generator is measured in the laboratory to verify the theoretical analysis presented above.

Characteristics of block strain and fault movement in the Sichuan-Yunnan region before and after Wenchuan earthquake

Deformation characteristics of the Sichuan-Yunnan region during the two periods 1999--2007 and 2007--2009 are analyzed with a block deformation model and GPS velocity profiles. The results show that the direction of the principal compressive strain rate of the Northwest-Sichuan block - the Mid-Yunnan block - the Southwest-Yunnan block was characterized by a clockwise rotation from north to south. The Anninghe and the Zemuhe faults had some shear-strain accumulation. The southern segment of the Xiaojiang fault had mainly strike-slip movement, while the northern segment was mainly accumulating strain. The 2008 Ms8.0 Wenchuan earthquake had some influence on the mid-southern segment of the Lijiang-Xiaojinhe fault, the Anninghe fault and the Jinshajiang fault, but not the Zemuhe fault, the Xiaojiang fault and the Red River fault as much.

Ore-controlling Characteristics of Synchronous Faults of Dongshengmiao Polymetallic Sulfide Deposits in Inner Mongolia

1 Introduction The Dongshengmiao deposit is a super-large Zn-Pb polymetallic sulfide deposit which occurring in the Langshan-Zhaertaaishan metallogenic belt,and located in the western margin of the North China Platform.The ore-bodies of Dongshengmiao deposits are mainly hosted in the second Formation of Langshan Group.There are some studies on the geological characteristics(Peng et al.,2004),geological and

Research on Present Activity Characteristics of Heizi Fault and Discussion of Its Relative Problems

Based on other previous researches, we recalculate the micro-displacement along the Heizi fault with recent deformation data of the Heizi reservoir. The result shows that activity characteristics of Heizi fault has changed greatly since 1973 and have experienced four phases. The third phase is characteristics of normal fault, and others characteristic of reverse faults. Constructing the reservoir dam and reservoir sluice has important effect on present activity of the fault, even changed the activity characteristics of faults in some phases. Seismicity has some effect on deformation data and fault activity.

Analysis of Some Characteristics of the Fault Activities in Eastern China by Satellite Images

Active faults have special electromagnetic effect and remote sensing characteristics, and exhibit unique im-agery marks in satellite images. A comprehensive comparison of images of active faults in eastern China and ananalysis of geologic and geomorphic data can tell us some characteristics of fault activity in the area during theneotectonic period: 1) The fault activities of the north-south tectonic zone, North China and Taiwan werestronger than those of southeastern and northeastern China; 2) the faulting in the north-south tectonic zone,North China and Taiwan has continued up to now, and most of the fault activites in southeastern andnorth-eastern China have become weaker since the Middle Pleistocene; 3) the activity is unsteady in time, mostbeing intermittent, or episodic, i.e. alternately strong and weak; 4) most active faults of a definite size can be di-vided into several segments which somewhat differ from each other in the characteristics of the activity.

Fault isolation of air handling unit based on neural network

Aiming at various faults in an air conditioning system,the fault characteristics are analyzed.The influence of the faults on the energy consumption and thermal comfort of the system are also discussed.The simulation results show that the measurement faults of the supply air temperature can lead to the increase in energy consumption.According to the fault characteristics,a data-driven method based on a neural network is presented to detect and diagnose the faults of air handling units.First,the historical data are selected to train the neural network so that it can recognize and predict the operation of the system.Then,the faults can be diagnosed by calculating the relative errors denoting the difference between the measuring values and the prediction outputs.Finally,the fault diagnosis strategy using the neural network is validated by using a simulator based on the TRNSYS platform.The results show that the neural network can diagnose different faults of the temperature,the flow rate and the pressure sensors in the air conditioning system.

Rolling element bearing instantaneous rotational frequency estimation based on EMD soft-thresholding denoising and instantaneous fault characteristic frequency

The accurate estimation of the rolling element bearing instantaneous rotational frequency(IRF) is the key capability of the order tracking method based on time-frequency analysis. The rolling element bearing IRF can be accurately estimated according to the instantaneous fault characteristic frequency(IFCF). However, in an environment with a low signal-to-noise ratio(SNR), e.g., an incipient fault or function at a low speed, the signal contains strong background noise that seriously affects the effectiveness of the aforementioned method. An algorithm of signal preprocessing based on empirical mode decomposition(EMD) and wavelet shrinkage was proposed in this work. Compared with EMD denoising by the cross-correlation coefficient and kurtosis(CCK) criterion, the method of EMD soft-thresholding(ST) denoising can ensure the integrity of the signal, improve the SNR, and highlight fault features. The effectiveness of the algorithm for rolling element bearing IRF estimation by EMD ST denoising and the IFCF was validated by both simulated and experimental bearing vibration signals at a low SNR.

A Fault Risk Warning Method of Integrated Energy Systems Based on RelieF-Softmax Algorithm

The integrated energy systems,usually including electric energy,natural gas and thermal energy,play a pivotal role in the energy Internet project,which could improve the accommodation of renewable energy through multienergy complementary ways.Focusing on the regional integrated energy system composed of electrical microgrid and natural gas network,a fault risk warning method based on the improved RelieF-softmax method is proposed in this paper.The raw data-set was first clustered by the K-maxmin method to improve the preference of the random sampling process in the RelieF algorithm,and thereby achieved a hierarchical and non-repeated sampling.Then,the improved RelieF algorithm is used to identify the feature vectors,calculate the feature weights,and select the preferred feature subset according to the initially set threshold.In addition,a correlation coefficient method is applied to reduce the feature subset,and further eliminate the redundant feature vectors to obtain the optimal feature subset.Finally,the softmax classifier is used to obtain the early warnings of the integrated energy system.Case studies are conducted on an integrated energy system in the south of China to demonstrate the accuracy of fault risk warning method proposed in this paper.

Electrical Structure and Fault Features of Crust and Upper Mantle beneath the Western Margin of the Qinghai-Tibet Plateau:Evidence from the Magnetotelluric Survey along Zhada-Quanshui Lake Profile

The magnetotelluric （MT） survey along the Zhada （札达）-Quanshui （泉水） Lake profile on the western margin of the Qinghai （青海）-Tibet plateau shows that the study area is divided into three tectonic provinces by the Yalung Tsangpo and Bangong （班公）-Nujiang （怒江） sutures. From south to north these are the Himalayan terrane, Gangdise terrane, and Qiangtang （羌塘） terrane. For the study area, there are widespread high-conductivity layers in the mid and lower crust, the top layers of which fluctuate intensively. The high-conductivity layer within the Gangdise terrane is deeper than those within the Qiangtang terrane and the Himalaya terrane, and the deepest high-conductivity layer is to the south of the Bangong-Nujiang suture. The top surface of the high-conductivity layer in the south of the Bangong-Nujiang suture is about 20 km lower than that in the north of it. The high-conductivity layer within the Gangdise terrane dips toward north and there are two high-conductivity layers within the crust of the southern Qiangtang terrane. In the upper crust along the profile, there are groups of lateral electrical gradient zones or distortion zones of different scales and occurrence indicating the distribution of faults and sutures along the profile. According to the electrical structure, the structural characteristics and space distribution of the Yalung Tsangpo suture, Bangong.Nujiang suture, and the major faults of Longmucuo （龙木错） and Geerzangbu are inferred.

Fault location method for petal-shaped distribution network with inverter-interfaced distributed generators

In this paper,a fault location method for the petal-shaped distribution network(PSDN)with inverter-interfaced distributed generators(IIDGs)is proposed to shorten the time of manual inspection.In order to calculate the fault position,the closed-loop structure of the PSDN is skillfully exploited,and the common control strategies of IIDGs are considered.For asymmetrical faults,a fault line identification formula based on the negative-sequence current phase differences is presented,and a fault location formula only utilizing the negative-sequence current amplitudes is derived to calculated the fault position.For symmetrical faults,the positive-sequence current at both ends of lines and the current output from IIDGs are used to identify the fault line,and the positive-sequence current on multiple lines are used to pinpoint the fault position.In this method,corresponding current phasors are separated into amplitudes and phases to satisfy the limitation of communication level.The simulation results show that the error is generally less than 1%,and the accuracy of the proposed method is not affected by the fault type,fault position,fault resistance,load current,and the IIDG penetration.

Research on fault mode and diagnosis of methane sensor

To improve the reliability of coal mine safety monitoring systems we have analyzed the characteristics of a methane sensor, an important component of the monitoring system of production safety in a coal mine and studied the main type and mode of faults when the sensor was used on-line. We introduced a new method based on artificial neural network to detect faults of methane sensors. In addition, using the output information of a single methane sensor, we established a sensor output model of a dynamic non-linear neural network for on-line fault detection. Finally, the fault of the heating wire of the sensor was simulated, indicating that, when the methane sensor had a fault, the predicted output of the neural network clearly deviated from the actual output, exceeding the pre-set threshold and showing that a fault had occurred in the methane sensor. The result shows that the model has good convergence and stability, and is quite capable of meeting the requirements for on-line fault detection of methane sensors.

Dynamic Fault Model for On-Line Evaluation of Yarn End Breakage during Ring Spinning

In this paper, a dynamic fault model is proposed to predict yarn end breakage in the spinning procedure through investigation of fault characteristics. In view of the principle that uniformity bad in raw material causes iustable yarn formation, the investigation focuses on the fault characteristic existing in the dynamic tension. Analyzing the dynamic spinning system, the phenomenon of over random shock in a spinning triangle is discovered to be the main physical event prior to yarn end breakage. The fault characteristic is further confirmed by dynamic tests and signal processing, and can be used to make an approach to predicting yarn end breakage. A relative energy feature is defined for evaluating the tendency of yarn end breakage, and its effectiveness is verified by on.line monitoring tests in the laboratory. The research results show that the proposed dynamic fault model has not only an advantage in indicating the presence of fault characteristics, but also great potentials in quantitating fault in online spinning monitoring.

Prospects and Current Studies on the Fault Zone Seismic Waves

Deep structure and material properties of faults can be understood by observing and simulating the particular phase in a fault fracture zone. This paper reviews the development of fault-zone seismic waves in the seismological domain. The present research status of fault-zone head wave and trapped wave are summarized systematically. Based on recent progress in this field,the paper discusses the prospect on the utilization of seismic wave in fault structure research.

New Activity of the Tanlu Fault Zone in the South of Huaihe to the Nvshanhu Segment since the Late Quaternary

Taking the Huaihe to the Nvshanhu segment of the Tanlu( Tancheng-Lujiang) fault zone as the main research target to explore whether there has been new activity since the late Quaternary,and based on the interpretation of remote sensing images and repeated surface investigations,we excavated trenches at the sections where the tectonic landform is significant,identified and recorded the deformation patterns of the fault and analyzed the activity behavior. Samples of new activity and deformation were collected and oriented slices were ground based on the samples ' original state to make the micro structural analysis and demonstration. All of the above research shows very clear linear tectonic geomorphology along the fault,three trenches across the fault zone all revealed new deformation traces since late Quaternary. The latest stratum dislocated by the fault is the late Quaternary and Holocene. The main slip mode is stick slip,as represented typically by fault scarps,wedge accumulation,the faults and the filled cracks and so on. In general,it shows the characteristics of brittle high-speed deformation and belongs to the prehistoric earthquake ruins. The above understanding was confirmed partially by microscopic analysis. In addition,the similarities and differences and the possible reasons for the characteristics of the latest activities of the Tancheng-Lujiang fault zone in the north and south of the Huaihe River regions are also discussed in this paper.

Asymmetrical Fault Current Calculation Method and Influencing Factors Analysis of Droop-Controlled Inverters

Since the fault dynamic of droop-controlled inverter is different from synchronous generators (SGs), protection devices may become invalid, and the fault overcurrent may damage power electronic devices and threaten the safety of the microgrid. Therefore, it is imperative to conduct a comprehensive fault analysis of the inverter to guide the design of protection schemes. However, due to the complexity of droop control strategy, existing literatures have simplified asymmetric fault analysis of droop-controlled inverters to varying degrees. Therefore, accurate fault analysis of a droop-controlled inverter is needed. In this paper, by analyzing the control system, an accurate fault model is established. Based on this, a calculation method for instantaneous asymmetrical fault current is proposed. In addition, the current components and current characteristics are analyzed. It was determined that fault currents are affected by control loops, fault types, fault distance and nonlinear limiters. In particular, the influences of limiters on the fault model, fault current calculation and fault current characteristics were analyzed. Through detailed analysis, it was found that dynamics of the control loop cannot be ignored, the fault type and fault distance determine fault current level, and part of the limiters will totally change the fault current trend. Finally, calculation and experimental results verify the correctness of the proposed method.

Transient Characteristics and Accommodative Current Limiting Strategy for Bidirectional Interlinking Converters in Hybrid AC/DC Microgrids

Bidirectional interlinking converter(BIC)is the core equipment in a hybrid AC/DC microgrid connected between AC and DC sub-grids.However,the variety of control modes and flexible bidirectional power flow complicate the influence of AC faults on BIC itself and on DC sub-grid,which potentially threaten both converter safety and system reliability.This study first investigates AC fault influence on the BIC and DC bus voltage under different BIC control modes and different pre-fault operation states,by developing a mathematical model and equivalent sequence network.Second,based on the analysis results,a general accommodative current limiting strategy is proposed for BIC without limitations to specific mode or operation condition.Current amplitude is predicted and constrained according to the critical requirements to protect the BIC and relieving the AC fault influence on the DC bus voltage.Compared with conventional methods,potential current limit failure and distortions under asymmetric faults can also be avoided.Finally,experiments verify feasibility of the proposed method.

Conjugate Vectors Method Applied to Asymmetrical Fault Analysis of Power Electronized Power Systems

With the wide application of power electronized resources(PERs),the amplitude and frequency of voltages show significant time-varying characteristics under asymmetrical faults.As a result,the traditional phasor model,impedance model,and symmetrical components method based on the constant amplitude and frequency of voltages are facing great challenges.Hence,a novel asymmetrical fault analysis method based on conjugate vectors is proposed in this paper which can meet the modeling and analysis requirements of the network excited by voltages with time-varying amplitude/frequency.Furthermore,asymmetrical fault characteristics are extracted.As an application,a faulted phase identification(FPI)strategy is proposed based on the fault characteristics.The correctness and superiority of the asymmetrical fault analysis method and FPI strategy are verified in time-domain simulations and a real-time digital simulator.

Review on Renewable Energy Source Fault Characteristics Analysis

The increase of renewable energy sources(RESs),especially wind power and photovoltaic,is bringing different fault features to the power system compared with the traditional syn-chronous generator,resulting in the urgent need for precise fault analysis.According to the sequentially activated fault features,the short circuit characteristics of RES can be divided into three fault stages.Within the staged framework of fault duration,the published research is reviewed to provide a systematic analysis of RES fault characteristics.It's concluded that the hardware parameter determines the sub-transient fault features of RES,whereas RES control begins to dominate during the following transient stage.However,the neglection of voltage transition and unavailable RES output phase shall impede the application of the analytical conclusions in protection design.To solve the existing problems,interaction among RES and networks must be figured out.Therefore,the fault calculation of the integral RES-grid system is offered as the research prospect.

A Similarity Comparison Based Pilot Protection Scheme for VSC-HVDC Grids Considering Fault Current Limiting Strategy

In the voltage source converter based high-voltage direct current(VSC-HVDC)grids,fast and reliable protections are the key technologies.The traditional protection schemes are easily affected by fault resistance,line distributed capacitance,etc.Meanwhile,the influence of fault current limiting strategy(FCLS)has not been fully considered.In this paper,the fault characteristics under FCLS and the feasibility of traditional travelling wave protections are analyzed.To improve the reliability and sensibility,a similarity comparison based pilot protection scheme is proposed,which focuses on the relationship between the fault characteristics and the state of the protected transmission line,with the establishment of a precise frequencydependent transmission line model.The criteria based on the similarity comparison calculated by cross-wavelet can identify the fault effectively.Meanwhile,the protection scheme can also endure the influence of error synchronization.Finally,the protection performance is verified in the PSCAD/EMTDC under different fault conditions.