Based on the global basement reservoir database and the dissection of basement reservoirs in China,the characteristics of hydrocarbon accumulation in basement reservoirs are analyzed,and the favorable conditions for h...Based on the global basement reservoir database and the dissection of basement reservoirs in China,the characteristics of hydrocarbon accumulation in basement reservoirs are analyzed,and the favorable conditions for hydrocarbon accumulation in deep basement reservoirs are investigated to highlight the exploration targets.The discovered basement reservoirs worldwide are mainly buried in the Archean and Precambrian granitic and metamorphic formations with depths less than 4500 m,and the relatively large reservoirs have been found in rift,back-arc and foreland basins in tectonic active zones of the Meso-Cenozoic plates.The hydrocarbon accumulation in basement reservoirs exhibits the characteristics in three aspects.First,the porous-fractured reservoirs with low porosity and ultra-low permeability are dominant,where extensive hydrocarbon accumulation occurred during the weathering denudation and later tectonic reworking of the basin basement.High resistance to compaction allows the physical properties of these highly heterogeneous reservoirs to be independent of the buried depth.Second,the hydrocarbons were sourced from the formations outside the basement.The source-reservoir assemblages are divided into contacted source rock-basement and separated source rock-basement patterns.Third,the abnormal high pressure in the source rock and the normal–low pressure in the basement reservoirs cause a large pressure difference between the source rock and the reservoirs,which is conducive to the pumping effect of hydrocarbons in the deep basement.The deep basement prospects are mainly evaluated by the factors such as tectonic activity of basement,source-reservoir combination,development of large deep faults(especially strike-slip faults),and regional seals.The Precambrian crystalline basements at the margin of the intracontinental rifts in cratonic basins,as well as the Paleozoic folded basements and the Meso-Cenozoic fault-block basements adjacent to the hydrocarbon generation depressions,have favorable conditions for hydrocarbon accumulation,and thus they are considered as the main targets for future exploration of deep basement reservoirs.展开更多
The Ordovician reservoirs in the Tahe oilfield are dominated by fractured-vuggy carbonate reservoirs, of which fault-karst reservoirs are a hot topic in recent years. Fault-karst reservoirs feature high production, la...The Ordovician reservoirs in the Tahe oilfield are dominated by fractured-vuggy carbonate reservoirs, of which fault-karst reservoirs are a hot topic in recent years. Fault-karst reservoirs feature high production, large burial depth, and strong heterogeneity under the control of faulting and karstification. Based on geological, logging, and seismic data, this study classified the Ordovician fault-karst reservoirs in the Yuejin block of the Tahe oilfield into three types, namely karst-cave, dissolved-vug, and fractured types, and established the integrated identification criteria of the three types of reservoirs. This study characterized karst caves, dissolved vugs, and multi-scale faults through seismic wave impedance inversion and frequency-domain detection of multi-scale faults. 3D geological models of different types of reservoirs were built using the combined deterministic and stochastic methods and characterized the spatial distribution of multi-scale faults, karst caves, dissolved vugs, and physical property parameters of reservoir. This study established the method for the geological modeling of fault-karst reservoirs, achieved the quantitative characterization and revealed the heterogeneity of fault-karst reservoirs. The karst-cave and dissolved-vug types are high in porosity and act as reservoirs, while the fractured type is high in permeability and act as flow pathway. This study lays the foundation for the development index prediction, well emplacement, and efficient development of the fault-karst carbonate reservoirs.展开更多
Deep and ultra-deep reservoirs have gradually become the primary focus of hydrocarbon exploration as a result of a series of significant discoveries in deep hydrocarbon exploration worldwide.These reservoirs present u...Deep and ultra-deep reservoirs have gradually become the primary focus of hydrocarbon exploration as a result of a series of significant discoveries in deep hydrocarbon exploration worldwide.These reservoirs present unique challenges due to their deep burial depth(4500-8882 m),low matrix permeability,complex crustal stress conditions,high temperature and pressure(HTHP,150-200℃,105-155 MPa),coupled with high salinity of formation water.Consequently,the costs associated with their exploitation and development are exceptionally high.In deep and ultra-deep reservoirs,hydraulic fracturing is commonly used to achieve high and stable production.During hydraulic fracturing,a substantial volume of fluid is injected into the reservoir.However,statistical analysis reveals that the flowback rate is typically less than 30%,leaving the majority of the fluid trapped within the reservoir.Therefore,hydraulic fracturing in deep reservoirs not only enhances the reservoir permeability by creating artificial fractures but also damages reservoirs due to the fracturing fluids involved.The challenging“three-high”environment of a deep reservoir,characterized by high temperature,high pressure,and high salinity,exacerbates conventional forms of damage,including water sensitivity,retention of fracturing fluids,rock creep,and proppant breakage.In addition,specific damage mechanisms come into play,such as fracturing fluid decomposition at elevated temperatures and proppant diagenetic reactions at HTHP conditions.Presently,the foremost concern in deep oil and gas development lies in effectively assessing the damage inflicted on these reservoirs by hydraulic fracturing,comprehending the underlying mechanisms,and selecting appropriate solutions.It's noteworthy that the majority of existing studies on reservoir damage primarily focus on conventional reservoirs,with limited attention given to deep reservoirs and a lack of systematic summaries.In light of this,our approach entails initially summarizing the current knowledge pertaining to the types of fracturing fluids employed in deep and ultra-deep reservoirs.Subsequently,we delve into a systematic examination of the damage processes and mechanisms caused by fracturing fluids within the context of hydraulic fracturing in deep reservoirs,taking into account the unique reservoir characteristics of high temperature,high pressure,and high in-situ stress.In addition,we provide an overview of research progress related to high-temperature deep reservoir fracturing fluid and the damage of aqueous fracturing fluids to rock matrix,both artificial and natural fractures,and sand-packed fractures.We conclude by offering a summary of current research advancements and future directions,which hold significant potential for facilitating the efficient development of deep oil and gas reservoirs while effectively mitigating reservoir damage.展开更多
The findings of a study to ascertain and assess the petrophysical characteristics of Cape Three Points reservoirs in the Western basin with a view to describe the reservoir quantitatively using Well Logs, Petrel and T...The findings of a study to ascertain and assess the petrophysical characteristics of Cape Three Points reservoirs in the Western basin with a view to describe the reservoir quantitatively using Well Logs, Petrel and Techlog. The investigated characteristics, which were all deduced from geophysical wire-line logs, include lithology, porosity, permeability, fluid saturation, and net to gross thickness. To characterise the reservoir on the field, a suite of wire-line logs including gamma ray, resistivity, spontaneous potential, and density logs for three wells (WELL_1X, WELL_2X, and WELL_3X) from the Tano Cape Three Point basin were studied. The analyses that were done included lithology delineation, reservoir identification, and petrophysical parameter determination for the identified reservoirs. The tops and bases of the three wells analysed were marked at a depth of 1203.06 - 2015.64 m, 3863.03 - 4253.85 m and 2497.38 - 2560.32 m respectively. There were no hydrocarbons in the reservoirs from the studies. The petrophysical parameters computed for each reservoir provided porosities of 13%, 3% and 11% respectively. The water saturation also determined for these three wells (WELL_1X, WELL_2X and WELL_3X) were 94%, 95% and 89% respectively. These results together with the behaviour of the density and neutron logs suggested that these wells are wildcat wells.展开更多
Almost all sandstone reservoirs contain interlayers. The identification and characterization of these interlayers iscritical for minimizing the uncertainty associated with oilfield development and improving oil and ga...Almost all sandstone reservoirs contain interlayers. The identification and characterization of these interlayers iscritical for minimizing the uncertainty associated with oilfield development and improving oil and gas recovery.Identifying interlayers outside wells using identification methods based on logging data and machine learning isdifficult and seismic-based identification techniques are expensive. Herein, a numerical model based on seepageand well-testing theories is introduced to identify interlayers using transient pressure data. The proposed modelrelies on the open-source MATLAB Reservoir Simulation Toolbox. The effects of the interlayer thickness, position,and width on the pressure response are thoroughly investigated. A procedure for inverting interlayer parametersin the reservoir using the bottom-hole pressure is also proposed. This method uses only transient pressuredata during well testing and can effectively identify the interlayer distribution near the wellbore at an extremelylow cost. The reliability of the model is verified using effective oilfield examples.展开更多
Field evidence indicates that proppant distribution and threshold pressure gradient have great impacts on well productivity.Aiming at the development of unconventional oil reservoirs in Triassic Chang-7 Unit,Ordos Bas...Field evidence indicates that proppant distribution and threshold pressure gradient have great impacts on well productivity.Aiming at the development of unconventional oil reservoirs in Triassic Chang-7 Unit,Ordos Basin of China,we presented an integrated workflow to investigate how(1)proppant placement in induced fracture and(2)non-linear flow in reservoir matrix would affect well productivity and fluid flow in the reservoir.Compared with our research before(Yue et al.,2020),here we extended this study into the development of multi-stage fractured horizontal wells(MFHWs)with large-scale complicated fracture geometry.The integrated workflow is based on the finite element method and consists of simulation models for proppant-laden fluid flow,fracture flow,and non-linear seepage flow,respectively.Simulation results indicate that the distribution of proppant inside the induced cracks significantly affects the productivity of the MFHW.When we assign an idealized proppant distribution instead of the real distribution,there will be an overestimation of 44.98%in daily oil rate and 30.63%in cumulative oil production after continuous development of 1000 days.Besides,threshold pressure gradient(TPG)also significantly affects the well performance in tight oil reservoirs.If we simply apply linear Darcy’s law to the reservoir matrix,the overall cumulative oil production can be overrated by 77%after 1000 days of development.In general,this research provides new insights into the development of tight oil reservoirs with TPG and meanwhile reveals the significance of proppant distribution and non-linear fluid flow in the production scenario design.展开更多
Slickwater fracturing fluids have gained widespread application in the development of tight oil reservoirs. After the fracturing process, the active components present in slickwater can directly induce spontaneous imb...Slickwater fracturing fluids have gained widespread application in the development of tight oil reservoirs. After the fracturing process, the active components present in slickwater can directly induce spontaneous imbibition within the reservoir. Several variables influence the eventual recovery rate within this procedure, including slickwater composition, formation temperature, degree of reservoir fracture development, and the reservoir characteristics. Nonetheless, the underlying mechanisms governing these influences remain relatively understudied. In this investigation, using the Chang-7 block of the Changqing Oilfield as the study site, we employ EM-30 slickwater fracturing fluid to explore the effects of the drag-reducing agent concentration, imbibition temperature, core permeability, and core fracture development on spontaneous imbibition. An elevated drag-reducing agent concentration is observed to diminish the degree of medium and small pore utilization. Furthermore, higher temperatures and an augmented permeability enhance the fluid flow properties, thereby contributing to an increased utilization rate across all pore sizes. Reduced fracture development results in a lower fluid utilization across diverse pore types. This study deepens our understanding of the pivotal factors affecting spontaneous imbibition in tight reservoirs following fracturing. The findings act as theoretical, technical, and scientific foundations for optimizing fracturing strategies in tight oil reservoir transformations.展开更多
The fractured-vuggy carbonate oil resources in the western basin of China are extremely rich.The connectivity of carbonate reservoirs is complex,and there is still a lack of clear understanding of the development and ...The fractured-vuggy carbonate oil resources in the western basin of China are extremely rich.The connectivity of carbonate reservoirs is complex,and there is still a lack of clear understanding of the development and topological structure of the pore space in fractured-vuggy reservoirs.Thus,effective prediction of fractured-vuggy reservoirs is difficult.In view of this,this work employs adaptive point cloud technology to reproduce the shape and capture the characteristics of a fractured-vuggy reservoir.To identify the complex connectivity among pores,fractures,and vugs,a simplified one-dimensional connectivity model is established by using the meshless connection element method(CEM).Considering that different types of connection units have different flow characteristics,a sequential coupling calculation method that can efficiently calculate reservoir pressure and saturation is developed.By automatic history matching,the dynamic production data is fitted in real-time,and the characteristic parameters of the connection unit are inverted.Simulation results show that the three-dimensional connectivity model of the fractured-vuggy reservoir built in this work is as close as 90%of the fine grid model,while the dynamic simulation efficiency is much higher with good accuracy.展开更多
There are two factors,source composition and magmatic differentiation,potentially controlling W-Sn mineralization.Which one is more important is widely debated and may need to be determined for each individual deposit...There are two factors,source composition and magmatic differentiation,potentially controlling W-Sn mineralization.Which one is more important is widely debated and may need to be determined for each individual deposit.The Xitian granite batholith located in South China is a natural laboratory for investigating the above problem.It consists essentially of two separate components,formed in the Triassic at ca.226 Ma and Jurassic at ca.152 Ma,respectively.The Triassic and Jurassic rocks are both composed of porphyritic and fine-grained phases.The latter resulted from highlydifferentiated porphyritic ones but they have similar textural characteristics and mineral assemblages,indicating that they reached a similar degree of crystal fractionation.Although both fine-grained phases are highly differentiated with elevated rare metal contents,economic W–Sn mineralization is rare in the Triassic granitoids and this can be attributed to less fertile source materials than their Jurassic counterparts,with a slightly more enriched isotopic signature and whole-rockεNd(226 Ma)of−10.4 to−9.2(2σ=0.2)compared withεNd(152 Ma)of−9.2 to−8.2(2σ=0.2)for the Jurassic rocks.The initial W-Sn enrichment was derived from the metasedimentary rocks and strongly enhanced by reworking of the continental crust,culminating in the Jurassic.展开更多
Niligou Reservoir,a typical reservoir in the eastern region of Jilin Province,is subordinate to Niligou River,which is located in the Changbai Mountains in eastern Jilin,with abundant plant and animal resources and we...Niligou Reservoir,a typical reservoir in the eastern region of Jilin Province,is subordinate to Niligou River,which is located in the Changbai Mountains in eastern Jilin,with abundant plant and animal resources and well protected biodiversity in the basin,but there are also some related problems such as fragile ecosystem of forest wetland.This paper carried out a health assessment of Niligou River,including water quality monitoring,aquatic organism monitoring,and riparian zone investigation.According to the requirements of the Technical Guidelines for River and Lake Health Assessment,13 assessment indexes were selected to build a river and lake health assessment index system.By sorting and analyzing the monitoring and investigation data,we got a clear picture of the ecological environment status and existing problems of Niligou Res-ervoir.Based on the actual situation of Niligou River,we evaluated the hydrologic integrity,chemical integrity,morphological and structural integrity,biological integrity and sustainability of social service function,and put forward corresponding countermeasures according to the re-sults,in order to provide a technical support for the health treatment of rivers and lakes in Jilin Province.展开更多
Ultra-low permeability reservoirs are characterized by small pore throats and poor physical properties, which areat the root of well-known problems related to injection and production. In this study, a gas injection f...Ultra-low permeability reservoirs are characterized by small pore throats and poor physical properties, which areat the root of well-known problems related to injection and production. In this study, a gas injection floodingapproach is analyzed in the framework of numerical simulations. In particular, the sequence and timing of fracturechanneling and the related impact on production are considered for horizontal wells with different fracturemorphologies. Useful data and information are provided about the regulation of gas channeling and possible strategiesto delay gas channeling and optimize the gas injection volume and fracture parameters. It is shown that inorder to mitigate gas channeling and ensure high production, fracture length on the sides can be controlled andlonger fractures can be created in the middle by which full gas flooding is obtained at the fracture location in themiddle of the horizontal well. A Differential Evolution (DE) algorithm is provided by which the gas injectionvolume and the fracture parameters of gas injection flooding can be optimized. It is shown that an improvedoil recovery factor as high as 6% can be obtained.展开更多
Conformance control and water plugging are a widely used EOR method in mature oilfields.However,majority of conformance control and water plugging agents are unavoidable dehydrated situation in high-temperature and hi...Conformance control and water plugging are a widely used EOR method in mature oilfields.However,majority of conformance control and water plugging agents are unavoidable dehydrated situation in high-temperature and high-salinity low permeability reservoirs.Consequently,a novel conformance control system HPF-Co gel,based on high-temperature stabilizer(CoCl_(2)·H_(2)O,CCH)is developed.The HPF-Co bulk gel has better performances with high temperature(120℃)and high salinity(1×10^(5)mg/L).According to Sydansk coding system,the gel strength of HPF-Co with CCH is increased to code G.The dehydration rate of HPF-Co gel is 32.0%after aging for 150 d at 120℃,showing excellent thermal stability.The rheological properties of HPF gel and HPF-Co gel are also studied.The results show that the storage modulus(G′)of HPF-Co gel is always greater than that of HPF gel.The effect of CCH on the microstructure of the gel is studied.The results show that the HPF-Co gel with CCH has a denser gel network,and the diameter of the three-dimensional network skeleton is 1.5-3.5μm.After 90 d of aging,HPF-Co gel still has a good three-dimensional structure.Infrared spectroscopy results show that CCH forms coordination bonds with N and O atoms in the gel amide group,which can suppress the vibration of cross-linked sites and improve the stability at high temperature.Fractured core plugging test determines the optimized polymer gel injection strategy and injection velocity with HPF-Co bulk gel system,plugging rate exceeding 98%.Moreover,the results of subsequent waterflooding recovery can be improved by 17%.展开更多
To reduce CO_(2) emissions in response to global climate change,shale reservoirs could be ideal candidates for long-term carbon geo-sequestration involving multi-scale transport processes.However,most current CO_(2) s...To reduce CO_(2) emissions in response to global climate change,shale reservoirs could be ideal candidates for long-term carbon geo-sequestration involving multi-scale transport processes.However,most current CO_(2) sequestration models do not adequately consider multiple transport mechanisms.Moreover,the evaluation of CO_(2) storage processes usually involves laborious and time-consuming numerical simulations unsuitable for practical prediction and decision-making.In this paper,an integrated model involving gas diffusion,adsorption,dissolution,slip flow,and Darcy flow is proposed to accurately characterize CO_(2) storage in depleted shale reservoirs,supporting the establishment of a training database.On this basis,a hybrid physics-informed data-driven neural network(HPDNN)is developed as a deep learning surrogate for prediction and inversion.By incorporating multiple sources of scientific knowledge,the HPDNN can be configured with limited simulation resources,significantly accelerating the forward and inversion processes.Furthermore,the HPDNN can more intelligently predict injection performance,precisely perform reservoir parameter inversion,and reasonably evaluate the CO_(2) storage capacity under complicated scenarios.The validation and test results demonstrate that the HPDNN can ensure high accuracy and strong robustness across an extensive applicability range when dealing with field data with multiple noise sources.This study has tremendous potential to replace traditional modeling tools for predicting and making decisions about CO_(2) storage projects in depleted shale reservoirs.展开更多
With the development of industrial activities,global warming has accelerated due to excessive emission of CO_(2).Enhanced Geothermal System(EGS)utilizes deep geothermal heat for power generation.Although porous medium...With the development of industrial activities,global warming has accelerated due to excessive emission of CO_(2).Enhanced Geothermal System(EGS)utilizes deep geothermal heat for power generation.Although porous medium theory is commonly employed to model geothermal reservoirs in EGS,Hot Dry Rock(HDR)presents a challenge as it consists of impermeable granite with zero porosity,potentially distorting the physical interpretation.To address this,the Lattice Boltzmann Method(LBM)is employed to simulate CO_(2)flow within geothermal reservoirs and the Finite Volume Method(FVM)to solve the energy conservation equation for temperature distribution.This combined method of LBM and FVM is imple-mented using MATLAB.The results showed that the Reynolds numbers(Re)of 3,000 and 8,000 lead to higher heat extraction rates from geothermal reservoirs.However,higher Re values may accelerate thermal breakthrough,posing challenges to EGS operation.Meanwhile,non-equilibrium of density in fractures becomes more pronounced during the system's life cycle,with non-Darcy's law becoming significant at Re values of 3,000 and 8,000.Density stratification due to buoyancy effects significantly impacts temperature distribution within geothermal reservoirs,with buoyancy effects at Re=100 under gravitational influence being noteworthy.Larger Re values(3,000 and 8,000)induce stronger forced convection,leading to more uniform density distribution.The addition of proppant negatively affects heat transfer performance in geothermal reservoirs,especially in single fractures.Practical engineering considerations should determine the quantity of proppant through detailed numerical simulations.展开更多
Rate-transient analysis(RTA)has been widely applied to extract estimates of reservoir/hydraulic fracture properties.However,the majority of RTA techniques can lead to misdiagnosis of reservoir/fracture information whe...Rate-transient analysis(RTA)has been widely applied to extract estimates of reservoir/hydraulic fracture properties.However,the majority of RTA techniques can lead to misdiagnosis of reservoir/fracture information when the reservoir exhibits reservoir heterogeneity and multiphase flow simultaneously.This work proposes a practical-yet-rigorous method to decouple the effects of reservoir heterogeneity and multiphase flow during TLF,and improve the evaluation of reservoir/fracture properties.A new,general,semi-analytical model is proposed that explicitly accounts for multiphase flow,fractalbased reservoir heterogeneity,anomalous diffusion,and pressure-dependent fluid properties.This is achieved by introducing a new Boltzmann-type transformation,the exponent of which includes reservoir heterogeneity and anomalous diffusion.In order to decouple the effects of reservoir heterogeneity and multiphase flow during TLF,the modified Boltzmann variable allows the conversion of three partial differential equations(PDE's)(i.e.,oil,gas and water diffusion equations)into ordinary differential equations(ODE's)that are easily solved using the Runge-Kutta(RK)method.A modified time-power-law plot is also proposed to estimate the reservoir and fracture properties,recognizing that the classical square-root-of-time-plot is no longer valid when various reservoir complexities are exhibited simultaneously.Using the slope of the straight line on the modified time-power-law plot,the linear flow parameter can be estimated with more confidence.Moreover,because of the new Boltzmann-type transformation,reservoir and fracture properties can be derived more efficiently without the need for defining complex pseudo-variable transformations.Using the new semi-analytical model,the effects of multiphase flow,reservoir heterogeneity and anomalous diffusion on rate-decline behavior are evaluated.For the case of approximately constant flowing pressure,multiphase flow impacts initial oil rate,which is a function of oil relative permeability and well flowing pressure.However,multiphase flow has a minor effect on the oil production decline exponent.Reservoir heterogeneity/anomalous diffusion affect both the initial oil production rate and production decline exponent.The production decline exponent constant is a function of reservoir heterogeneity/anomalous diffusion only.The practical significance of this work is the advancement of RTA techniques to allow for more complex reservoir scenarios,leading to more accurate production forecasting and better-informed capital planning.展开更多
The classical source-to-trap petroleum system concept only considers the migration and accumulation of conventional oil and gas in traps driven dominantly by buoyance in a basin,although revised and improved,even some...The classical source-to-trap petroleum system concept only considers the migration and accumulation of conventional oil and gas in traps driven dominantly by buoyance in a basin,although revised and improved,even some new concepts as composite petroleum system,total petroleum system,total composite petroleum system,were proposed,but they do not account for the vast unconventional oil and gas reservoirs within the system,which is not formed and distributed in traps dominantly by buoyancedriven.Therefore,the petroleum system concept is no longer adequate in dealing with all the oil and gas accumulations in a basin where significant amount of the unconventional oil and gas resources are present in addition to the conventional oil and gas accumulations.This paper looked into and analyzed the distribution characteristics of conventional and unconventional oil/gas reservoirs and their differences and correlations in petroliferous basins in China and North America,and then proposed whole petroleum system(WPS)concept,the WPS is defined as a natural system that encompasses all the conventional and unconventional oil and gas,reservoirs and resources originated from organic matter in source rocks,the geological elements and processes involving the formation,evolution,and distribution of these oil and gas,reservoirs and resources.It is found in the WPS that there are three kinds of hydrocarbons dynamic fields,three kinds of original hydrocarbons,three kinds of reservoir rocks,and the coupling of these three essential elements lead to the basic ordered distribution model of shale oil/gas reservoirs contacting or interbeded with tight oil/gas reservoirs and separated conventional oil/gas reservoirs from source rocks upward,which is expressed as“S\T-C”.Abnormal conditions lead to other three special ordered distribution models:The first is that with shale oil/gas reservoirs separated from tight oil/gas reservoirs.The second is that with two direction ordered distributions from source upward and downward.The third is with lateral distribution from source outside.展开更多
Due to the poor physical properties of tight reservoirs,CO_(2) huff-n-puff(HNP)is considered a potential enhanced oil recovery(EOR)method after primary depletion.Optimization plays a critical role in the effective imp...Due to the poor physical properties of tight reservoirs,CO_(2) huff-n-puff(HNP)is considered a potential enhanced oil recovery(EOR)method after primary depletion.Optimization plays a critical role in the effective implementation of CO_(2) huff-n-puff.But the optimization requires a good understanding of the EOR mechanisms.In this work,the spatial distribution of oil saturation under different experimental conditions was analyzed by the NMR method to further discuss the HNP mechanisms.According to the variation of 1D frequency signal amplitude,we divided the core into the hardly movable area and movable area,the region with the obvious signal decline was defined as the movable area,and the hardly movable area was the region with limited signal decline.Based on that the recovery characteristics of different scenarios were evaluated.Firstly,the necessity of the soaking stage was studied,where three scenarios with different soaking times were carried out.Secondly,the injection pressure was adjusted to investigate the effect of the pressure gradient.The T_(2) spectra show that soaking has significantly improved the production of crude oil in small pores,and higher oil recovery in a single cycle is observed,but it is lower when the elapsed time(total operation time)is the same.31.03% of oil can be recovered after 3 cycles HNP,which increases to 33.8% and 37.06% for the 4 cycles and 6 cycles cases.As the pressure gradient increases,more oil is removed out of the matrix,and the oil in the deep part of the reservoir can be effectively recovered.During the CO_(2) huff-n-puff process,the oil distributions are similar to the solution gas drive,the residual oil is distributed at the close end of the core and the range that the oil can be efficiently recovered is limited.展开更多
The natural cracking of crude oils in deep reservoirs has gained great interest due to continuously increasing depth of petroleum exploration and exploitation.Complex oil compositions and surroundings as well as compl...The natural cracking of crude oils in deep reservoirs has gained great interest due to continuously increasing depth of petroleum exploration and exploitation.Complex oil compositions and surroundings as well as complicated geological evolutions make oil cracking in nature much more complex than industrial pyrolysis.So far,numerous studies,focused on this topic,have made considerable progress although there still exist some drawbacks.However,a comprehensive review on crude oil cracking is yet to be conducted.This article systematically reviews the controlling factors of oil cracking from six aspects,namely,oil compositions,temperature and time,pressure,water,minerals and solid organic matter.We compare previous experimental and modelling results and present new field cases.In the following,we evaluate the prevailing estimation methods for the extent of oil cracking,and elucidate other factors that may interfere with the application of these estimation methods.This review will be helpful for further investigations of crude oil cracking and provides a guide for estimation of the cracking extent of crude oils.展开更多
The quantitative understanding of hydraulic fracture(HF)properties guides accurate production forecasts and reserve estimation.Type curve is a powerful technique to characterize HF and reservoir properties from flowba...The quantitative understanding of hydraulic fracture(HF)properties guides accurate production forecasts and reserve estimation.Type curve is a powerful technique to characterize HF and reservoir properties from flowback and long-term production data.However,two-phase flow of water and hydrocarbon after an HF stimulation together with the complex transport mechanisms in shale nanopores exacerbate the nonlinearity of the transport equation,causing errors in type-curve analysis.Accordingly,we propose a new two-phase type-curve method to estimate HF properties,such as HF volume and permeability of fracture,through the analysis of flowback data of multi-fractured shale wells.The proposed type curve is based on a semianalytical solution that couples the two-phase flow from the matrix with the flow in HF by incorporating matrix influx,slippage effect,stress dependence,and the spatial variation of fluid properties in inorganic and organic pores.For the first time,multiple fluid transport mechanisms are considered into two-phase type-curve analysis for shale reservoirs.We analyze the flowback data from a multi-fractured horizontal well in a shale gas reservoir to verify the field application of the proposed method.The results show that the fracture properties calculated by the type-curve method are in good agreement with the long-time production data.展开更多
Low permeability sandstone reservoirs in China typically have more complicated geological conditions, pore structures, and flow characteristics as compared to medium-to-high-permeability sandstone reservoirs. Traditio...Low permeability sandstone reservoirs in China typically have more complicated geological conditions, pore structures, and flow characteristics as compared to medium-to-high-permeability sandstone reservoirs. Traditional geological and seepage theories, and engineering methods are not applicable to the development of these low permeability reservoirs, and wells drilled into them often produce oil and gas at very low rates. Recent breakthroughs in reservoir exploitation technology have greatly improved the productivity of low permeability reservoirs, making them the primary target for oil exploration and extraction in China. The development theories and practices applied to low permeability reservoirs in China are reviewed in this study— based on relevant geological and engineering practices, including drilling, fracturing, recovery, and surface engineering. A unique series of technological advances that aid the development of low permeability reservoirs in China are summarized here. This study may serve as a meaningful guide in achieving scale efficiency for the development of low permeability reservoirs.展开更多
基金Supported by the Science and Technology Project of China National Petroleum Corporation(2021DJ02).
文摘Based on the global basement reservoir database and the dissection of basement reservoirs in China,the characteristics of hydrocarbon accumulation in basement reservoirs are analyzed,and the favorable conditions for hydrocarbon accumulation in deep basement reservoirs are investigated to highlight the exploration targets.The discovered basement reservoirs worldwide are mainly buried in the Archean and Precambrian granitic and metamorphic formations with depths less than 4500 m,and the relatively large reservoirs have been found in rift,back-arc and foreland basins in tectonic active zones of the Meso-Cenozoic plates.The hydrocarbon accumulation in basement reservoirs exhibits the characteristics in three aspects.First,the porous-fractured reservoirs with low porosity and ultra-low permeability are dominant,where extensive hydrocarbon accumulation occurred during the weathering denudation and later tectonic reworking of the basin basement.High resistance to compaction allows the physical properties of these highly heterogeneous reservoirs to be independent of the buried depth.Second,the hydrocarbons were sourced from the formations outside the basement.The source-reservoir assemblages are divided into contacted source rock-basement and separated source rock-basement patterns.Third,the abnormal high pressure in the source rock and the normal–low pressure in the basement reservoirs cause a large pressure difference between the source rock and the reservoirs,which is conducive to the pumping effect of hydrocarbons in the deep basement.The deep basement prospects are mainly evaluated by the factors such as tectonic activity of basement,source-reservoir combination,development of large deep faults(especially strike-slip faults),and regional seals.The Precambrian crystalline basements at the margin of the intracontinental rifts in cratonic basins,as well as the Paleozoic folded basements and the Meso-Cenozoic fault-block basements adjacent to the hydrocarbon generation depressions,have favorable conditions for hydrocarbon accumulation,and thus they are considered as the main targets for future exploration of deep basement reservoirs.
基金supported by the Strategic Priority Research Program of the Chinese Academy of Sciences (XDA14010204).
文摘The Ordovician reservoirs in the Tahe oilfield are dominated by fractured-vuggy carbonate reservoirs, of which fault-karst reservoirs are a hot topic in recent years. Fault-karst reservoirs feature high production, large burial depth, and strong heterogeneity under the control of faulting and karstification. Based on geological, logging, and seismic data, this study classified the Ordovician fault-karst reservoirs in the Yuejin block of the Tahe oilfield into three types, namely karst-cave, dissolved-vug, and fractured types, and established the integrated identification criteria of the three types of reservoirs. This study characterized karst caves, dissolved vugs, and multi-scale faults through seismic wave impedance inversion and frequency-domain detection of multi-scale faults. 3D geological models of different types of reservoirs were built using the combined deterministic and stochastic methods and characterized the spatial distribution of multi-scale faults, karst caves, dissolved vugs, and physical property parameters of reservoir. This study established the method for the geological modeling of fault-karst reservoirs, achieved the quantitative characterization and revealed the heterogeneity of fault-karst reservoirs. The karst-cave and dissolved-vug types are high in porosity and act as reservoirs, while the fractured type is high in permeability and act as flow pathway. This study lays the foundation for the development index prediction, well emplacement, and efficient development of the fault-karst carbonate reservoirs.
基金Dao-Bing Wang was supported by the Beijing Natural Science Foundation Project(No.3222030)the National Natural Science Foundation of China(No.52274002)+1 种基金the PetroChina Science and Technology Innovation Foundation Project(No.2021DQ02-0201)Fu-Jian Zhou was supported by the National Natural Science Foundation of China(No.52174045).
文摘Deep and ultra-deep reservoirs have gradually become the primary focus of hydrocarbon exploration as a result of a series of significant discoveries in deep hydrocarbon exploration worldwide.These reservoirs present unique challenges due to their deep burial depth(4500-8882 m),low matrix permeability,complex crustal stress conditions,high temperature and pressure(HTHP,150-200℃,105-155 MPa),coupled with high salinity of formation water.Consequently,the costs associated with their exploitation and development are exceptionally high.In deep and ultra-deep reservoirs,hydraulic fracturing is commonly used to achieve high and stable production.During hydraulic fracturing,a substantial volume of fluid is injected into the reservoir.However,statistical analysis reveals that the flowback rate is typically less than 30%,leaving the majority of the fluid trapped within the reservoir.Therefore,hydraulic fracturing in deep reservoirs not only enhances the reservoir permeability by creating artificial fractures but also damages reservoirs due to the fracturing fluids involved.The challenging“three-high”environment of a deep reservoir,characterized by high temperature,high pressure,and high salinity,exacerbates conventional forms of damage,including water sensitivity,retention of fracturing fluids,rock creep,and proppant breakage.In addition,specific damage mechanisms come into play,such as fracturing fluid decomposition at elevated temperatures and proppant diagenetic reactions at HTHP conditions.Presently,the foremost concern in deep oil and gas development lies in effectively assessing the damage inflicted on these reservoirs by hydraulic fracturing,comprehending the underlying mechanisms,and selecting appropriate solutions.It's noteworthy that the majority of existing studies on reservoir damage primarily focus on conventional reservoirs,with limited attention given to deep reservoirs and a lack of systematic summaries.In light of this,our approach entails initially summarizing the current knowledge pertaining to the types of fracturing fluids employed in deep and ultra-deep reservoirs.Subsequently,we delve into a systematic examination of the damage processes and mechanisms caused by fracturing fluids within the context of hydraulic fracturing in deep reservoirs,taking into account the unique reservoir characteristics of high temperature,high pressure,and high in-situ stress.In addition,we provide an overview of research progress related to high-temperature deep reservoir fracturing fluid and the damage of aqueous fracturing fluids to rock matrix,both artificial and natural fractures,and sand-packed fractures.We conclude by offering a summary of current research advancements and future directions,which hold significant potential for facilitating the efficient development of deep oil and gas reservoirs while effectively mitigating reservoir damage.
文摘The findings of a study to ascertain and assess the petrophysical characteristics of Cape Three Points reservoirs in the Western basin with a view to describe the reservoir quantitatively using Well Logs, Petrel and Techlog. The investigated characteristics, which were all deduced from geophysical wire-line logs, include lithology, porosity, permeability, fluid saturation, and net to gross thickness. To characterise the reservoir on the field, a suite of wire-line logs including gamma ray, resistivity, spontaneous potential, and density logs for three wells (WELL_1X, WELL_2X, and WELL_3X) from the Tano Cape Three Point basin were studied. The analyses that were done included lithology delineation, reservoir identification, and petrophysical parameter determination for the identified reservoirs. The tops and bases of the three wells analysed were marked at a depth of 1203.06 - 2015.64 m, 3863.03 - 4253.85 m and 2497.38 - 2560.32 m respectively. There were no hydrocarbons in the reservoirs from the studies. The petrophysical parameters computed for each reservoir provided porosities of 13%, 3% and 11% respectively. The water saturation also determined for these three wells (WELL_1X, WELL_2X and WELL_3X) were 94%, 95% and 89% respectively. These results together with the behaviour of the density and neutron logs suggested that these wells are wildcat wells.
文摘Almost all sandstone reservoirs contain interlayers. The identification and characterization of these interlayers iscritical for minimizing the uncertainty associated with oilfield development and improving oil and gas recovery.Identifying interlayers outside wells using identification methods based on logging data and machine learning isdifficult and seismic-based identification techniques are expensive. Herein, a numerical model based on seepageand well-testing theories is introduced to identify interlayers using transient pressure data. The proposed modelrelies on the open-source MATLAB Reservoir Simulation Toolbox. The effects of the interlayer thickness, position,and width on the pressure response are thoroughly investigated. A procedure for inverting interlayer parametersin the reservoir using the bottom-hole pressure is also proposed. This method uses only transient pressuredata during well testing and can effectively identify the interlayer distribution near the wellbore at an extremelylow cost. The reliability of the model is verified using effective oilfield examples.
基金The authors gratefully acknowledge the financial supports from the National Science Foundation of China under Grant 52274027 as well as the High-end Foreign Experts Recruitment Plan of the Ministry of Science and Technology China under Grant G2022105027L.
文摘Field evidence indicates that proppant distribution and threshold pressure gradient have great impacts on well productivity.Aiming at the development of unconventional oil reservoirs in Triassic Chang-7 Unit,Ordos Basin of China,we presented an integrated workflow to investigate how(1)proppant placement in induced fracture and(2)non-linear flow in reservoir matrix would affect well productivity and fluid flow in the reservoir.Compared with our research before(Yue et al.,2020),here we extended this study into the development of multi-stage fractured horizontal wells(MFHWs)with large-scale complicated fracture geometry.The integrated workflow is based on the finite element method and consists of simulation models for proppant-laden fluid flow,fracture flow,and non-linear seepage flow,respectively.Simulation results indicate that the distribution of proppant inside the induced cracks significantly affects the productivity of the MFHW.When we assign an idealized proppant distribution instead of the real distribution,there will be an overestimation of 44.98%in daily oil rate and 30.63%in cumulative oil production after continuous development of 1000 days.Besides,threshold pressure gradient(TPG)also significantly affects the well performance in tight oil reservoirs.If we simply apply linear Darcy’s law to the reservoir matrix,the overall cumulative oil production can be overrated by 77%after 1000 days of development.In general,this research provides new insights into the development of tight oil reservoirs with TPG and meanwhile reveals the significance of proppant distribution and non-linear fluid flow in the production scenario design.
基金The authors sincerely appreciate the financial support from the National Natural Science Foundation of China(No.52074279,51874261).
文摘Slickwater fracturing fluids have gained widespread application in the development of tight oil reservoirs. After the fracturing process, the active components present in slickwater can directly induce spontaneous imbibition within the reservoir. Several variables influence the eventual recovery rate within this procedure, including slickwater composition, formation temperature, degree of reservoir fracture development, and the reservoir characteristics. Nonetheless, the underlying mechanisms governing these influences remain relatively understudied. In this investigation, using the Chang-7 block of the Changqing Oilfield as the study site, we employ EM-30 slickwater fracturing fluid to explore the effects of the drag-reducing agent concentration, imbibition temperature, core permeability, and core fracture development on spontaneous imbibition. An elevated drag-reducing agent concentration is observed to diminish the degree of medium and small pore utilization. Furthermore, higher temperatures and an augmented permeability enhance the fluid flow properties, thereby contributing to an increased utilization rate across all pore sizes. Reduced fracture development results in a lower fluid utilization across diverse pore types. This study deepens our understanding of the pivotal factors affecting spontaneous imbibition in tight reservoirs following fracturing. The findings act as theoretical, technical, and scientific foundations for optimizing fracturing strategies in tight oil reservoir transformations.
基金funded by the Natural Science Foundation of Xinjiang Uygur Autonomous Region (No.2022D01A330)the CNPC (China National Petroleum Corporation)Scientific Research and Technology Development Project (Grant No.2021DJ1501)+1 种基金National Natural Science Foundation Project (No.52274030)“Tianchi Talent”Introduction Plan of Xinjiang Uygur Autonomous Region (2022).
文摘The fractured-vuggy carbonate oil resources in the western basin of China are extremely rich.The connectivity of carbonate reservoirs is complex,and there is still a lack of clear understanding of the development and topological structure of the pore space in fractured-vuggy reservoirs.Thus,effective prediction of fractured-vuggy reservoirs is difficult.In view of this,this work employs adaptive point cloud technology to reproduce the shape and capture the characteristics of a fractured-vuggy reservoir.To identify the complex connectivity among pores,fractures,and vugs,a simplified one-dimensional connectivity model is established by using the meshless connection element method(CEM).Considering that different types of connection units have different flow characteristics,a sequential coupling calculation method that can efficiently calculate reservoir pressure and saturation is developed.By automatic history matching,the dynamic production data is fitted in real-time,and the characteristic parameters of the connection unit are inverted.Simulation results show that the three-dimensional connectivity model of the fractured-vuggy reservoir built in this work is as close as 90%of the fine grid model,while the dynamic simulation efficiency is much higher with good accuracy.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.92162210,42172096 and 41773028).
文摘There are two factors,source composition and magmatic differentiation,potentially controlling W-Sn mineralization.Which one is more important is widely debated and may need to be determined for each individual deposit.The Xitian granite batholith located in South China is a natural laboratory for investigating the above problem.It consists essentially of two separate components,formed in the Triassic at ca.226 Ma and Jurassic at ca.152 Ma,respectively.The Triassic and Jurassic rocks are both composed of porphyritic and fine-grained phases.The latter resulted from highlydifferentiated porphyritic ones but they have similar textural characteristics and mineral assemblages,indicating that they reached a similar degree of crystal fractionation.Although both fine-grained phases are highly differentiated with elevated rare metal contents,economic W–Sn mineralization is rare in the Triassic granitoids and this can be attributed to less fertile source materials than their Jurassic counterparts,with a slightly more enriched isotopic signature and whole-rockεNd(226 Ma)of−10.4 to−9.2(2σ=0.2)compared withεNd(152 Ma)of−9.2 to−8.2(2σ=0.2)for the Jurassic rocks.The initial W-Sn enrichment was derived from the metasedimentary rocks and strongly enhanced by reworking of the continental crust,culminating in the Jurassic.
文摘Niligou Reservoir,a typical reservoir in the eastern region of Jilin Province,is subordinate to Niligou River,which is located in the Changbai Mountains in eastern Jilin,with abundant plant and animal resources and well protected biodiversity in the basin,but there are also some related problems such as fragile ecosystem of forest wetland.This paper carried out a health assessment of Niligou River,including water quality monitoring,aquatic organism monitoring,and riparian zone investigation.According to the requirements of the Technical Guidelines for River and Lake Health Assessment,13 assessment indexes were selected to build a river and lake health assessment index system.By sorting and analyzing the monitoring and investigation data,we got a clear picture of the ecological environment status and existing problems of Niligou Res-ervoir.Based on the actual situation of Niligou River,we evaluated the hydrologic integrity,chemical integrity,morphological and structural integrity,biological integrity and sustainability of social service function,and put forward corresponding countermeasures according to the re-sults,in order to provide a technical support for the health treatment of rivers and lakes in Jilin Province.
基金supported by the Forward Looking Basic Major Scientific and Technological Projects of CNPC (Grant No.2021DJ2202).
文摘Ultra-low permeability reservoirs are characterized by small pore throats and poor physical properties, which areat the root of well-known problems related to injection and production. In this study, a gas injection floodingapproach is analyzed in the framework of numerical simulations. In particular, the sequence and timing of fracturechanneling and the related impact on production are considered for horizontal wells with different fracturemorphologies. Useful data and information are provided about the regulation of gas channeling and possible strategiesto delay gas channeling and optimize the gas injection volume and fracture parameters. It is shown that inorder to mitigate gas channeling and ensure high production, fracture length on the sides can be controlled andlonger fractures can be created in the middle by which full gas flooding is obtained at the fracture location in themiddle of the horizontal well. A Differential Evolution (DE) algorithm is provided by which the gas injectionvolume and the fracture parameters of gas injection flooding can be optimized. It is shown that an improvedoil recovery factor as high as 6% can be obtained.
基金This work has been Sponsored by CNPC Innovation Found(Grant No.2021DQ02-0202)Besides,the authors gratefully appreciate the financial support of the Science Foundation of China University of Petroleum,Beijing(Grant No.2462020XKBH013)Financial supports from the National Natural Science Foundation of China(Grant No.52174046)is also significantly acknowledged.
文摘Conformance control and water plugging are a widely used EOR method in mature oilfields.However,majority of conformance control and water plugging agents are unavoidable dehydrated situation in high-temperature and high-salinity low permeability reservoirs.Consequently,a novel conformance control system HPF-Co gel,based on high-temperature stabilizer(CoCl_(2)·H_(2)O,CCH)is developed.The HPF-Co bulk gel has better performances with high temperature(120℃)and high salinity(1×10^(5)mg/L).According to Sydansk coding system,the gel strength of HPF-Co with CCH is increased to code G.The dehydration rate of HPF-Co gel is 32.0%after aging for 150 d at 120℃,showing excellent thermal stability.The rheological properties of HPF gel and HPF-Co gel are also studied.The results show that the storage modulus(G′)of HPF-Co gel is always greater than that of HPF gel.The effect of CCH on the microstructure of the gel is studied.The results show that the HPF-Co gel with CCH has a denser gel network,and the diameter of the three-dimensional network skeleton is 1.5-3.5μm.After 90 d of aging,HPF-Co gel still has a good three-dimensional structure.Infrared spectroscopy results show that CCH forms coordination bonds with N and O atoms in the gel amide group,which can suppress the vibration of cross-linked sites and improve the stability at high temperature.Fractured core plugging test determines the optimized polymer gel injection strategy and injection velocity with HPF-Co bulk gel system,plugging rate exceeding 98%.Moreover,the results of subsequent waterflooding recovery can be improved by 17%.
基金This work is funded by National Natural Science Foundation of China(Nos.42202292,42141011)the Program for Jilin University(JLU)Science and Technology Innovative Research Team(No.2019TD-35).The authors would also like to thank the reviewers and editors whose critical comments are very helpful in preparing this article.
文摘To reduce CO_(2) emissions in response to global climate change,shale reservoirs could be ideal candidates for long-term carbon geo-sequestration involving multi-scale transport processes.However,most current CO_(2) sequestration models do not adequately consider multiple transport mechanisms.Moreover,the evaluation of CO_(2) storage processes usually involves laborious and time-consuming numerical simulations unsuitable for practical prediction and decision-making.In this paper,an integrated model involving gas diffusion,adsorption,dissolution,slip flow,and Darcy flow is proposed to accurately characterize CO_(2) storage in depleted shale reservoirs,supporting the establishment of a training database.On this basis,a hybrid physics-informed data-driven neural network(HPDNN)is developed as a deep learning surrogate for prediction and inversion.By incorporating multiple sources of scientific knowledge,the HPDNN can be configured with limited simulation resources,significantly accelerating the forward and inversion processes.Furthermore,the HPDNN can more intelligently predict injection performance,precisely perform reservoir parameter inversion,and reasonably evaluate the CO_(2) storage capacity under complicated scenarios.The validation and test results demonstrate that the HPDNN can ensure high accuracy and strong robustness across an extensive applicability range when dealing with field data with multiple noise sources.This study has tremendous potential to replace traditional modeling tools for predicting and making decisions about CO_(2) storage projects in depleted shale reservoirs.
基金supported by the Hebei Province Graduate Innovation Funding Project(CXZZBS2022029).
文摘With the development of industrial activities,global warming has accelerated due to excessive emission of CO_(2).Enhanced Geothermal System(EGS)utilizes deep geothermal heat for power generation.Although porous medium theory is commonly employed to model geothermal reservoirs in EGS,Hot Dry Rock(HDR)presents a challenge as it consists of impermeable granite with zero porosity,potentially distorting the physical interpretation.To address this,the Lattice Boltzmann Method(LBM)is employed to simulate CO_(2)flow within geothermal reservoirs and the Finite Volume Method(FVM)to solve the energy conservation equation for temperature distribution.This combined method of LBM and FVM is imple-mented using MATLAB.The results showed that the Reynolds numbers(Re)of 3,000 and 8,000 lead to higher heat extraction rates from geothermal reservoirs.However,higher Re values may accelerate thermal breakthrough,posing challenges to EGS operation.Meanwhile,non-equilibrium of density in fractures becomes more pronounced during the system's life cycle,with non-Darcy's law becoming significant at Re values of 3,000 and 8,000.Density stratification due to buoyancy effects significantly impacts temperature distribution within geothermal reservoirs,with buoyancy effects at Re=100 under gravitational influence being noteworthy.Larger Re values(3,000 and 8,000)induce stronger forced convection,leading to more uniform density distribution.The addition of proppant negatively affects heat transfer performance in geothermal reservoirs,especially in single fractures.Practical engineering considerations should determine the quantity of proppant through detailed numerical simulations.
基金The authors would like to acknowledge financial support provided by National Natural Science Foundation of China(No.52074338)We are also grateful to the support of the National Key R&D Program of China(No.2019YFA0708700)+1 种基金National Key Basic Research Program of China(20CX06071A)Bin Yuan would like to thank for the support of Shandong Mountain Tai Scholar Program.Chris Clarkson would like to acknowledge funding support from an NSERC Alliance grant(ALLRP 548652-19)for research related to the topic of this paper.
文摘Rate-transient analysis(RTA)has been widely applied to extract estimates of reservoir/hydraulic fracture properties.However,the majority of RTA techniques can lead to misdiagnosis of reservoir/fracture information when the reservoir exhibits reservoir heterogeneity and multiphase flow simultaneously.This work proposes a practical-yet-rigorous method to decouple the effects of reservoir heterogeneity and multiphase flow during TLF,and improve the evaluation of reservoir/fracture properties.A new,general,semi-analytical model is proposed that explicitly accounts for multiphase flow,fractalbased reservoir heterogeneity,anomalous diffusion,and pressure-dependent fluid properties.This is achieved by introducing a new Boltzmann-type transformation,the exponent of which includes reservoir heterogeneity and anomalous diffusion.In order to decouple the effects of reservoir heterogeneity and multiphase flow during TLF,the modified Boltzmann variable allows the conversion of three partial differential equations(PDE's)(i.e.,oil,gas and water diffusion equations)into ordinary differential equations(ODE's)that are easily solved using the Runge-Kutta(RK)method.A modified time-power-law plot is also proposed to estimate the reservoir and fracture properties,recognizing that the classical square-root-of-time-plot is no longer valid when various reservoir complexities are exhibited simultaneously.Using the slope of the straight line on the modified time-power-law plot,the linear flow parameter can be estimated with more confidence.Moreover,because of the new Boltzmann-type transformation,reservoir and fracture properties can be derived more efficiently without the need for defining complex pseudo-variable transformations.Using the new semi-analytical model,the effects of multiphase flow,reservoir heterogeneity and anomalous diffusion on rate-decline behavior are evaluated.For the case of approximately constant flowing pressure,multiphase flow impacts initial oil rate,which is a function of oil relative permeability and well flowing pressure.However,multiphase flow has a minor effect on the oil production decline exponent.Reservoir heterogeneity/anomalous diffusion affect both the initial oil production rate and production decline exponent.The production decline exponent constant is a function of reservoir heterogeneity/anomalous diffusion only.The practical significance of this work is the advancement of RTA techniques to allow for more complex reservoir scenarios,leading to more accurate production forecasting and better-informed capital planning.
基金This work was supported by the major science and technology projects of CNPC during the“14th five-year plan”(Grant number 2021DJ0101)。
文摘The classical source-to-trap petroleum system concept only considers the migration and accumulation of conventional oil and gas in traps driven dominantly by buoyance in a basin,although revised and improved,even some new concepts as composite petroleum system,total petroleum system,total composite petroleum system,were proposed,but they do not account for the vast unconventional oil and gas reservoirs within the system,which is not formed and distributed in traps dominantly by buoyancedriven.Therefore,the petroleum system concept is no longer adequate in dealing with all the oil and gas accumulations in a basin where significant amount of the unconventional oil and gas resources are present in addition to the conventional oil and gas accumulations.This paper looked into and analyzed the distribution characteristics of conventional and unconventional oil/gas reservoirs and their differences and correlations in petroliferous basins in China and North America,and then proposed whole petroleum system(WPS)concept,the WPS is defined as a natural system that encompasses all the conventional and unconventional oil and gas,reservoirs and resources originated from organic matter in source rocks,the geological elements and processes involving the formation,evolution,and distribution of these oil and gas,reservoirs and resources.It is found in the WPS that there are three kinds of hydrocarbons dynamic fields,three kinds of original hydrocarbons,three kinds of reservoir rocks,and the coupling of these three essential elements lead to the basic ordered distribution model of shale oil/gas reservoirs contacting or interbeded with tight oil/gas reservoirs and separated conventional oil/gas reservoirs from source rocks upward,which is expressed as“S\T-C”.Abnormal conditions lead to other three special ordered distribution models:The first is that with shale oil/gas reservoirs separated from tight oil/gas reservoirs.The second is that with two direction ordered distributions from source upward and downward.The third is with lateral distribution from source outside.
基金The work is supported by the Strategic Cooperation Technology Projects of CNPC and CUPB(ZLZX2020)by the Fundamental Research Funds for the Central Universities of China.
文摘Due to the poor physical properties of tight reservoirs,CO_(2) huff-n-puff(HNP)is considered a potential enhanced oil recovery(EOR)method after primary depletion.Optimization plays a critical role in the effective implementation of CO_(2) huff-n-puff.But the optimization requires a good understanding of the EOR mechanisms.In this work,the spatial distribution of oil saturation under different experimental conditions was analyzed by the NMR method to further discuss the HNP mechanisms.According to the variation of 1D frequency signal amplitude,we divided the core into the hardly movable area and movable area,the region with the obvious signal decline was defined as the movable area,and the hardly movable area was the region with limited signal decline.Based on that the recovery characteristics of different scenarios were evaluated.Firstly,the necessity of the soaking stage was studied,where three scenarios with different soaking times were carried out.Secondly,the injection pressure was adjusted to investigate the effect of the pressure gradient.The T_(2) spectra show that soaking has significantly improved the production of crude oil in small pores,and higher oil recovery in a single cycle is observed,but it is lower when the elapsed time(total operation time)is the same.31.03% of oil can be recovered after 3 cycles HNP,which increases to 33.8% and 37.06% for the 4 cycles and 6 cycles cases.As the pressure gradient increases,more oil is removed out of the matrix,and the oil in the deep part of the reservoir can be effectively recovered.During the CO_(2) huff-n-puff process,the oil distributions are similar to the solution gas drive,the residual oil is distributed at the close end of the core and the range that the oil can be efficiently recovered is limited.
基金This study is supported by the National Natural Science Foundation of China(Grants 41730424,41961144023 and 42002162)。
文摘The natural cracking of crude oils in deep reservoirs has gained great interest due to continuously increasing depth of petroleum exploration and exploitation.Complex oil compositions and surroundings as well as complicated geological evolutions make oil cracking in nature much more complex than industrial pyrolysis.So far,numerous studies,focused on this topic,have made considerable progress although there still exist some drawbacks.However,a comprehensive review on crude oil cracking is yet to be conducted.This article systematically reviews the controlling factors of oil cracking from six aspects,namely,oil compositions,temperature and time,pressure,water,minerals and solid organic matter.We compare previous experimental and modelling results and present new field cases.In the following,we evaluate the prevailing estimation methods for the extent of oil cracking,and elucidate other factors that may interfere with the application of these estimation methods.This review will be helpful for further investigations of crude oil cracking and provides a guide for estimation of the cracking extent of crude oils.
基金This research is supported by National Natural Science Foundation of China(No.52204057)the Science Foundation of China University of Petroleum,Beijing(No.2462021BJRC003 and 2462021YJRC012).
文摘The quantitative understanding of hydraulic fracture(HF)properties guides accurate production forecasts and reserve estimation.Type curve is a powerful technique to characterize HF and reservoir properties from flowback and long-term production data.However,two-phase flow of water and hydrocarbon after an HF stimulation together with the complex transport mechanisms in shale nanopores exacerbate the nonlinearity of the transport equation,causing errors in type-curve analysis.Accordingly,we propose a new two-phase type-curve method to estimate HF properties,such as HF volume and permeability of fracture,through the analysis of flowback data of multi-fractured shale wells.The proposed type curve is based on a semianalytical solution that couples the two-phase flow from the matrix with the flow in HF by incorporating matrix influx,slippage effect,stress dependence,and the spatial variation of fluid properties in inorganic and organic pores.For the first time,multiple fluid transport mechanisms are considered into two-phase type-curve analysis for shale reservoirs.We analyze the flowback data from a multi-fractured horizontal well in a shale gas reservoir to verify the field application of the proposed method.The results show that the fracture properties calculated by the type-curve method are in good agreement with the long-time production data.
基金support by the National Key Research and Development Program of China(Grant No.2018YFA0702400)is gratefully acknowledged.
文摘Low permeability sandstone reservoirs in China typically have more complicated geological conditions, pore structures, and flow characteristics as compared to medium-to-high-permeability sandstone reservoirs. Traditional geological and seepage theories, and engineering methods are not applicable to the development of these low permeability reservoirs, and wells drilled into them often produce oil and gas at very low rates. Recent breakthroughs in reservoir exploitation technology have greatly improved the productivity of low permeability reservoirs, making them the primary target for oil exploration and extraction in China. The development theories and practices applied to low permeability reservoirs in China are reviewed in this study— based on relevant geological and engineering practices, including drilling, fracturing, recovery, and surface engineering. A unique series of technological advances that aid the development of low permeability reservoirs in China are summarized here. This study may serve as a meaningful guide in achieving scale efficiency for the development of low permeability reservoirs.