High performance micromachining of sapphire by laser induced plasma assisted ablation(LIPAA)using GHz burst mode femtosecond pulses

GHz burst-mode femtosecond(fs)laser,which emits a series of pulse trains with extremely short intervals of several hundred picoseconds,provides distinct characteristics in materials processing as compared with the conventional irradiation scheme of fs laser(single-pulse mode).In this paper,we take advantage of the moderate pulse interval of 205 ps(4.88 GHz)in the burst pulse for high-quality and high-efficiency micromachining of single crystalline sapphire by laser induced plasma assisted ablation(LIPAA).Specifically,the preceding pulses in the burst generate plasma by ablation of copper placed behind the sapphire substrate,which interacts with the subsequent pulses to induce ablation at the rear surface of sapphire substrates.As a result,not only the ablation quality but also the ablation efficiency and the fabrication resolution are greatly improved compared to the other schemes including single-pulse mode fs laser direct ablation,single-pulse mode fs-LIPAA,and nanosecond-LIPAA.

Tunable Supercontinuum Generated in a Yb^3＋-Doped Microstructure Fiber Pumped by Ti：Sapphire Femtosecond Laser

We experimentally demonstrate that a tunable supercontinuum（SC） can be generated in a Yb3＋-doped microstructure fiber by the concept of wavelength conversion with a Ti：sapphire femtosecond（fs） laser as the pump.Experimental results show that an emission light around 1040 nm in an anomalous dispersion region is first generated and amplified by fs pulses in the normal dispersion region. Then, SC spectra from 1100 to 1380 nm and 630 to 840 nm can be achieved by combined effects of higher-order soliton fission and Raman soliton self-frequency shift in the anomalous dispersion region and self-phase modulation, dispersive wave, and four-wave mixing in the normal dispersion region. It is also demonstrated that the 20 nm change of pump results in a 280 nm broadband shift of soliton and the further red-shift of soliton is limited by OH-absorption at 1380 nm.

Operation of Kerr-lens mode-locked Ti:sapphire laser in the non-soliton regime

A Kerr-lens mode-locked Ti：sapphire laser operating in a non-soliton regime is demonstrated. Dispersive wave generation is observed as a result of third order dispersion in the vicinity of zero dispersion. The characteristics of the Ti：sapphire l^ser operating in a positive dispersion regime are presented, where the oscillator directly generates pulses with duration continuously tunable from 0.37 ps to 2.11 ps, and 36 fs pulses are achieved atter extracavity compression. The oscillation is numerically simulated with an extended nonlinear Schr6dinger equation, and the simulation results are in good agreement with the experimental results.

An all-solid-state high power quasi-continuous-wave tunable dual-wavelength Ti：sapphire laser system using birefringence filter

This paper describes a tunable dual-wavelength Ti：sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd：YAG laser as the pumping source, and the birefringence filter as the tuning element. Tunable dual-wavelength outputs with one wavelength range from 700 nm to 756.5 nm, another from 830 nm to 900mn have been demonstrated. With a pump power of 23 W at 532 nm, a repetition rate of 7 kHz and a pulse width of 47.6 ns, an output power of 5.1 W at 744.8 nm and 860.9 nm with a pulse width of 13.2 ns and a line width of 3 nm has been obtained, it indicates an optical-to-optical conversion efficiency of 22.2%.

A High-Pulse-Energy High-Beam-Quality Tunable Ti:Sapphire Laser Using a Prism-Dispersion Cavity

A high-pulse-energy high-beam-quality tunable Ti：sapphire laser pumped by a frequency-doubled Nd：YAG laser is demonstrated. Using a fused-silica prism as the dispersion element, a tuning range of 740-855 nm is obtained. At an incident pump energy of 774mJ, the maximum output energy of 104mJ at 790nm with a pulse width of 100μs is achieved at a repetition rate of 5 Hz. To the best of our knowledge, it is the highest pulse energy at 790 nm with pulse width of hundred micro-seconds for an all-solid-state laser. The linewidth of output is 0.5 nm, and the beam quality factor M2 is 1.16. The high-pulse-energy high-beam-quality tunable Ti：sapphire laser in the range of 740-855 nm can be used to establish a more accurate and consistent absolute scale of second-order optical-nonlinear coefficients for KBe2BO3F2 measured in a wider wavelength range and to assess Miller＇s rule quantitatively.

Diode-pumped Kerr-lens mode-locked Ti: sapphire laser with broad wavelength tunability

We report a direct blue-diode-pumped wavelength tunable Kerr-lens mode-locked Ti: sapphire laser.Central wavelength tunability as broad as 89 nm(736-825 nm) is achieved by adjusting the insertion of the prism.Pulses as short as 17 fs are generated at a central wavelength of 736 nm with an average output power of 31 mW.The maximum output power is 46.8 mW at a central wavelength of 797 nm with a pulse duration of 46 fs.

In-situ growth of Ca/P salt on Ti surface induced by femtosecond lasers in hydroxyapatite suspension

Pure Ti plate surfaces are micro-ablated by femtosecond lasers in the ambience of hydroxyapatite suspension. It is found that three-stage hierarchical surface structures are produced with various laser energies. When the laser energy is 150μJ, a lava-like structure with a distribution of nanoholes is dispersed evenly on the laser ablated surface. While in the case of 300 μJ, the grooves-and-islands micro-patterns covered with nanoparticles are generated on the surface. Remarkably, Ca/P based substances are revealed to firmly deposit on the micro-structured surfaces. More phosphate growth is seen for the higher laser energy. Discussions suggest that the additional elements deposition could be attributed to the chemical reaction of plasma related ions in the suspension and their subsequent crystallisation on the fresh surfaces of Ti plate due to the femtosecond laser ablation.

A 100-TW Ti:Sapphire Laser System at a Repetition Rate of 0.1 Hz

We demonstrate a 100-TW-class femtosecond Ti:sapphire laser running at a repetition rate of 0.1Hz based on a 20TW/10 Hz laser facility (XL-Ⅱ).Pumping the new stage amplifier with a 25J green Nd:glass laser,we successfully improve the laser energy to 3.4J with duration of 29 fs,corresponding to a peak power of 11 7 TW.

自锁模Ti：Al_2O_3激光器

通过在腔内引入双棱镜对研制的Ｔｉ：Ａｌ_２Ｏ_３激光器实现了稳定的自锁模运转，最窄脉宽达５３ｆｓ．分析了Ｔｉ：Ａｌ_２Ｏ_３激光器的自锁模原理及工作特性．

基于啁啾放大的飞秒太瓦量级Ti∶Al_2O_3激光器新进展

综述了基于啁啾放大技术的飞秒太瓦量级Ti∶Al_2O_3激光器的发展概况及最新进展 ,在详细分析了其应用前景的基础上 ,进一步指出了这一技术领域未来的发展趋势。

全固化自锁模飞秒Ti∶S激光器实验研究

首次在国内系统报道了以腔内 L BO倍频 Nd∶ YVO4 激光器为泵浦源的全固化自锁模飞秒钛宝石激光器的实验结果 .设计了一种热不敏腔内 LBO倍频线性折叠腔结构 ,获得到了2 5.5%的光转换效率 ,泵浦功率为 2 2 W时得到了 5.6 W的基模绿光输出功率 ;以该激光器为泵浦源 ,在线性 Z型腔的基础上 ,使用了一种能够通过改变腔内凹面聚焦镜折叠角消除象散的方法 ,直接由钛宝石激光器得到了脉冲宽度为 2 2 fs、功率为 3 0 0 m W的光脉冲 .整个激光系统稳定性好 ,噪音明显低于 Ar3 +

研制超高功率激光系统所需的优质大尺寸钛宝石晶体(Ti^(3+)∶Al_2O_3)

对作者采用温度梯度法(ＴＧＴ)生长的钛宝石晶体与美国晶体系统公司的晶体进行了性能比较,结果表明,两者晶体质量水平相当．

Ti-Ni合金飞秒激光打孔规律研究

飞秒激光具有极高的峰值功率,在精密加工中有着独特的优势。本文主要探索了加工参数(脉冲数、单脉冲能量和离焦量)的变化对小孔直径、深度和圆度的影响规律。实验研究发现:小孔直径随脉冲个数增加而略微增加;单脉冲能量越大,小孔直径越大;离焦量从0向正或负方向偏移时,小孔直径都随之增加;小孔深度随脉冲个数的增加而增加;单脉冲能量越大,小孔深度越大;随着脉冲个数的增加,圆度误差也相应的增加;单脉冲能量越大,圆度误差也越大,使用50个20μJ单脉冲能量脉冲加工,小孔圆度误差为8.2μm;随着激光焦点位置从样品内部逐渐移动到样品外部,圆度误差逐渐增大,离焦量为0时,500个20μJ单脉冲能量的脉冲加工,小孔圆度误差为5μm。本文所探索的飞秒激光小孔加工的规律对小孔加工实际应用具有参考和借鉴的作用。

Fabrication of sapphire rib waveguides using a femtosecond laser

We demonstrate a method for fabricating sapphire rib waveguides with femtosecond laser micromachining technology. Finite difference beam propagation method(FD-BPM) is applied to design sapphire rib waveguides. We explore the process of etching on a sapphire substrate surface via direct laser ablation. Rib waveguides that satisfies the dimensions of our design were fabricated. Actual light propagation performance is tested, and with the cut-back method, the insertion loss of 2.9±0.5 dB/cm is measured.

Harmonic Mode-Locked Ytterbium-Doped Fibre Ring Laser

We demonstrate a harmonic mode-locked ytterbium-doped fibre ring laser, which consists of a polarization-sensitive isolator, two polarization controllers, two 976nm laser diodes as the pump source and a two-segment ytterbium-doped fibre. Utilizing an additive pulse mode-locked technique based on nonlinear polarization evolution, the ytterbium-doped fibre laser can operate in mode-locked state by adjusting the position of polarization controllers. The cavity fundamental repetition rate is 23.78 MHz. We also observe the second- and third-harmonic mode locking in the normal dispersion region, and their repetition rates are 47.66 MHz and 71.56 MHz, respectively. Over-driving of the saturable absorber in the harmonic mode-locking pulse is analysed and discussed in detail.

Generation of 7-fs laser pulse directly from a compact Ti:sapphire laser with chirped mirrors

A compact femtosecond Ti:sapphire laser resonator consisting of three chirped mirrors and one output coupler was designed. By accurately balancing the intra- cavity dispersions between Ti:sapphire crystal, air and chirped mirrors, we directly generated the laser pulse shorter than 7 fs at the average power of 340 mW with 3.1 W pump. The repetition rate of the laser oscillator is 173 MHz at the centre wavelength of 791 nm, and the ultrabroaden spectrum covers from 600 nm to 1000 nm. To the best of our knowledge, this is the simplest laser resonator capable of generating sub-10 fs laser pulse.

Review of Femtosecond Laser Fabricated Fiber Bragg Gratings for High Temperature Sensing

This paper reviews high temperature sensing applications based on fiber Bragg gratings fabricated by use of femtosecond laser. Type II fiber Bragg gratings fabricated in the silica fiber can sustain up to 1200 ℃ while that fabricated in the sapphire fiber have the good thermal stability up to 1745 ℃.

Highly efficient TW multipass Ti:sapphire laser system

An efficient chirped-pulse amplification, Ti:sapphire laser system, has been developed using mainly domestic components. The gain-narrowing effect has been significantly overcome by shaping spectrum of seeding pulses. With a novel aberration-free stretcher and two stage multi-pass amplifiers, pulses with duration of 25 fs and 36-mJ energy have been obtained at 10 Hz repetition rate, using only less than 290 mJ green Nd: YAG pump energy. This corresponds to a 1.4 TW peak power and 32% main amplification efficiency. The energy stability of the laser systems is better than ± 3% .

Long-term frequency-stabilized optical frequency comb based on a turnkey Ti:sapphire mode-locked laser

We report a long-term frequency-stabilized optical frequency comb at 530–1100 nm based on a turnkey Ti:sapphire modelocked laser.With the help of a digital controller,turnkey operation is realized for the Ti:sapphire mode-locked laser.Under optimized design of the laser cavity,the laser can be mode-locked over a month,limited by the observation time.The combination of a fast piezo and a slow one inside the Ti:sapphire mode-locked laser allows us to adjust the cavity length with moderate bandwidth and tuning range,enabling robust locking of the repetition rate(f_(r)) to a hydrogen maser.By combining a fast analog feedback to pump current and a slow digital feedback to an intracavity wedge and the pump power of the Ti:sapphire mode-locked laser,the carrier envelope offset frequency(f_(ceo)) of the comb is stabilized.We extend the continuous frequency-stabilized time of the Ti:sapphire optical frequency comb to five days.The residual jitters of f;and f;are 0.08 m Hz and 2.5 m Hz at 1 s averaging time,respectively,satisfying many applications demanding accuracy and short operation time for optical frequency combs.

Highly stable femtosecond pulse generation from a MXene Ti_3C_2T_x(T = F, O, or OH) mode-locked fiber laser

Ultrafast fiber lasers are in great demand for various applications, such as optical communication, spectroscopy,biomedical diagnosis, and industrial fabrication. Here, we report the highly stable femtosecond pulse generation from a MXene mode-locked fiber laser. We have prepared the high-quality Ti_3C_2 T_x nanosheets via the etching method, and characterized their ultrafast dynamics and broadband nonlinear optical responses. The obvious intensity-and wavelength-dependent nonlinear responses have been observed and investigated. In addition, a highly stable femtosecond fiber laser with signal-to-noise ratio up to 70.7 dB and central wavelength of 1567.3 nm has been delivered. The study may provide some valuable design guidelines for the development of ultrafast, broadband nonlinear optical modulators, and open new avenues toward advanced photonic devices based on MXenes.