On the generation of high-quality Nyquist pulses in mode-locked fiber lasers

Nyquist pulses have wide applications in many areas,from electronics to optics.Mode-locked lasers are ideal platforms to generate such pulses.However,how to generate high-quality Nyquist pulses in mode-locked lasers remains elusive.We address this problem by managing different physical effects in mode-locked fiber lasers through extensive numerical simulations.We find that net dispersion,linear loss,gain and filter shaping can affect the quality of Nyquist pulses significantly.We also demonstrate that Nyquist pulses experience similariton shaping due to the nonlinear attractor effect in the gain medium.Our work may contribute to the design of Nyquist pulse sources and enrich the understanding of pulse shaping dynamics in mode-locked lasers.

Real-Time 4-Mode MDM Transmission Using Commercial 400G OTN Transceivers and All-Fiber Mode Multiplexers

Weakly-coupled mode division multiplexing(MDM)technique is considered a promising candidate to enhance the capacity of an optical transmission system,in which mode multiplexers/demultiplexers(MMUX/MDEMUX)with low insertion loss and modal crosstalk are the key components.In this paper,a low-modal-crosstalk 4-mode MMUX/MDEMUX for the weakly-coupled triple-ring-core few-mode fiber(TRC-FMF)is designed and fabricated with side-polishing processing.The measurement results show that a pair of MMUX/MDEMUX and 25 km weakly-coupled TRC-FMF MDM link achieve low modal crosstalk of lower than−17.5 dB and insertion loss of lower than 11.56 dB for all the four modes.Based on the TRC-FMF and all-fiber MMUX/MDEMUX,an experiment for 25 km real-time 4-mode 3-λwavelength division multiplexing(WDM)-MDM transmission is conducted using commercial 400G optical transport network(OTN)transceivers.The experimental results prove weakly-coupled MDM techniques facilitate a smooth upgrade of the optical transmission system.

基于FMF的两模式单通道1000 km MDM传输

【目的】随着第五代移动通信技术(5G)、物联网和云计算等信息化带宽消耗型业务的不断涌现,人们对信息高速传输的需求急剧增长。然而由于固有的非线性效应,单模光纤的传输容量已逼近香农极限,其将不再能满足人们对于超高速大容量传输的需求。解决传输容量问题成为当务之急。为了解决大容量通信系统的需求与长距离高速传输等问题,文章搭建了两模式单通道的C波段少模光纤(FMF)传输系统。【方法】在发送端,使用任意波形发生器将数字信号转换为电信号,驱动正交(IQ)调制器对光载波进行调制。调制的信号同时使用模分复用(MDM)和偏振复用(PDM)两种复用技术进行传输。为了实现1000 km的双模信号长距离传输,文章构建了一个双循环回路系统,信号每通过一次环路都将通过一段50 km长的FMF。在传输到目标距离后,由耦合器输出到解复用模块,相干光接收机对解复用的调制信号进行零差检测。最后,存储到示波器进行离线数字信号处理(DSP)。依次对信号进行频域色散补偿、下采样、时钟恢复和最小均方算法,恢复出原始信号。【结果】文章发现,在实验中各信道光信噪比(OSNR)所处的区间内,低信噪比(SNR)情况下误码率(BER)接近理论信道结果,高SNR情况下BER为1×10^(-2)时与理论值相差2.5 dB。文章分别测试了背靠背(BTB)和250、500、750以及1000 km下LP 11a和LP 11b两种模式的BER,在所有距离下的BER均低于实验中设定的28%冗余的低密度奇偶校验码(LDPC)的软判决前向纠错(SD-FEC)门限(5.2×10^(-2))。1000 km传输后的BER分别为1.7×10^(-2)和1.8×10^(-2),总净传输速率为400 Gbit/s。【结论】文章演示了32 Gbaud MDM-PDM 16进制正交振幅调制(QAM)的宽带C波段信号在1000 km的两模式单通道FMF系统中的传输。在接收端,利用先进的多输入多输出(MIMO)DSP算法进行信道均衡,得到的两模式BER分别为1.7×10^(-2)和1.8×10^(-2),均低于28%冗余的LDPC SD-FEC门限。传输结果达成了基于FMF传输400 Gbit/s的净传输速率国内纪录,并突出了FMF在大容量远距离传输方面的潜力。

Dissipative soliton resonance within different dispersion regimes in a single mode-locked laser

Dissipative soliton resonance(DSR) was previously studied in separated mode-locked fiber lasers within different dispersion regimes including anomalous, near-zero and normal dispersion. Here we propose a method to study DSR in a single mode-locked laser in these different dispersion regimes. This is achieved by virtue of a waveshaper which can control the laser dispersion readily using software, avoiding the usual tedious cutback method. We find that dispersion has a negligible effect on DSR since the pulse duration keeps constant while dispersion is varied. Moreover, we examine the dynamics of DSR on the parameters of the SA including modulation depth and saturation power, and find that the pulse duration can be changed in a large range when the saturation power is decreased. Our numerical simulations could be important to guide relative experimental studies.

Passive harmonic mode-locking of Er-doped fiber laser using CVD-grown few-layer MoS_2 as a saturable absorber

Passive harmonic mode locking of an erbium-doped fiber laser based on few-layer molybdenum disulfide(MoS2)saturable absorber(SA) is demonstrated. The few-layer MoS2 is prepared by the chemical vapor deposition(CVD) method and then transferred onto the end face of a fiber connector to form a fiber-compatible Mo S2SA. The 20 th harmonic modelocked pulses at 216-MHz repetition rate are stably generated with a pulse duration of 1.42 ps and side-mode suppression ratio(SMSR) of 36.1dB. The results confirm that few-layer MoS2 can serve as an effective SA for mode-locked fiber lasers.

Modeling of Few-Mode Multi-Core Optical Fiber Channe Based on Non-Uniform Mode Field Distribution

In this paper, the influencing factors that affect few-mode and multi core optical fiber channel are analyzed in a comprehensive way. The theoretical modeling and computer simulation of the information channel are carried out and then the modeling scheme of few-mode multicore optical fiber channel based on non-uniform mode field distribution is put forward. The proposed modeling scheme can not only exponentially increases the system capacity through fewmode multi-core optical fiber channel, but has better transmission performance compared to the channel of the same type to the uniform channel revealing from the simulation results.

4.096 Tbit/s multidimensional multiplexing signals transmission over 1000 km few mode fiber

We experimentally transmit eight wavelength-division-multiplexing(WDM)channels,16 quadratic-amplitude-modulation(QAM)signals at 32-GBaud,over 1000 km few mode fiber(FMF).In this experiment,we use WDM,mode division multiplexing,and polarization multiplexing for signal transmission.Through the multiple-input-multiple-output(MIMO)equalization algorithms,we achieve the total line transmission rate of 4.096 Tbit/s.The results prove that the bit error rates(BERs)for the16QAM signals after 1000 km FMF transmission are below the soft-decision forward-error-correction(SD-FEC)threshold of2.4×10^(-2),and the net rate reaches 3.413 Tbit/s.Our proposed system provides a reference for the future development of high-capacity communication.

Research and analysis of Brillouin distributed sensing system based on quasi-single-mode few-mode fiber

A distributed fiber sensor was fabricated by splicing two single-mode fibers(SMFs)using the few-mode fiber(FMF)technique.A Brillouin optical time domain analysis(BOTDA)system was developed to measure the sensor’s temperature and bending performance.Two-mode and four-mode step FMFs were combined to splice the few-mode segment.The results indicate that the temperature response coefficients of the few-mode segment are only slightly higher than those of the connected single-mode segment,measuring at 1.13 MHz/℃and 1.12 MHz/℃,respectively.The minimum bending radius for the sensor is 0.9 cm,and the four-mode bending response curve is superior to that of the two-mode one,proving that 4-SI-FMF offers better bending sensitivity.

Fast mode decomposition for few-mode fiber based on lightweight neural network

In this paper,we present a fast mode decomposition method for few-mode fibers,utilizing a lightweight neural network called MobileNetV3-Light.This method can quickly and accurately predict the amplitude and phase information of different modes,enabling us to fully characterize the optical field without the need for expensive experimental equipment.We train the MobileNetV3-Light using simulated near-field optical field maps,and evaluate its performance using both simulated and reconstructed near-field optical field maps.To validate the effectiveness of this method,we conduct mode decomposition experiments on a few-mode fiber supporting six linear polarization(LP)modes(LP01,LP11e,LP11o,LP21e,LP21o,LP02).The results demonstrate a remarkable average correlation of 0.9995 between our simulated and reconstructed near-field lightfield maps.And the mode decomposition speed is about 6 ms per frame,indicating its powerful real-time processing capability.In addition,the proposed network model is compact,with a size of only 6.5 MB,making it well suited for deployment on portable mobile devices.

Pulse-train nonuniformity in an all-fiber ring laser passively mode-locked by nonlinear polarization rotation

This paper reports the periodic power variation of the pulse-train in a passively mode-locked soliton fiber ring laser. It can obtain either the uniform or nonuniform pulse-train output by simply rotating the polarization controllers. The experimental results show that the pulse-train nonuniformity is caused by the interaction between the nonuniform polarization states of the soliton pulses and the passive polarizer in the cavity.

Passively mode-locked erbium-doped fiber laser via a D-shape-fiber-based MoS_2 saturable absorber with a very low nonsaturable loss

We report on the generation of conventional and dissipative solitons in erbium-doped fiber lasers by the evanescent field interaction between the propagating light and a multilayer molybdenum disulfide（MoS_2） thin film. The MoS_2 film is fabricated by depositing the MoS_2 water–ethanol mixture on a D-shape-fiber（DF） repetitively. The measured nonsaturable loss, saturable optical intensity, and the modulation depth of this device are 13.3%, 110 MW/cm^2, and 3.4% respectively.Owing to the very low nonsaturable loss, the laser threshold of conventional soliton is as low as 4.8 mW. The further increase of net cavity dispersion to normal regime, stable dissipation soliton pulse trains with a spectral bandwidth of 11.7 nm and pulse duration of 116 ps are successfully generated. Our experiment demonstrates that the MoS_2-DF device can indeed be used as a high performance saturable absorber for further applications in ultrafast photonics.

Stable single longitudinal mode erbium-doped silica fiber laser based on an asymmetric linear three-cavity structure

We present a stable linear-cavity single longitudinal mode （SLM） erbium-doped silica fiber laser. It consists of four fiber Bragg gratings （FBGs） directly written in a section of photosensitive erbium-doped fiber （EDF） to form an asymmetric three-cavity structure. The stable SLM operation at a wavelength of 1545.112 nm with a 3-dB bandwidth of 0.012 nm and an optical signal-to-noise ratio （OSNR） of about 60 dB is verified experimentally. Under laboratory conditions, the performance of a power fluctuation of less than 0.05 dB observed from the power meter for 6 h and a wavelength variation of less than 0.01 nm obtained from the optical spectrum analyzer （OSA） for about 1.5 h are demonstrated. The gain fiber length is no longer limited to only several centimeters for SLM operation because of the excellent mode-selecting ability of the asymmetric three-cavity structure. The proposed scheme provides a simple and cost-effective approach to realizing a stable SLM fiber laser.

Mode-locked fiber laser with MoSe_2 saturable absorber based on evanescent field

An all-fiber mode-locked fiber laser was achieved with a saturable absorber based on a tapered fiber deposited with layered molybdenum selenide(MoSe_2). The laser was operated at a central wavelength of 1558.35 nm with an output spectral width of 2.9 nm, and a pulse repetition rate of 16.33 MHz. To the best of our knowledge, this is the first report on mode-locked fiber lasers using MoSe_2 saturable absorbers based on tapered fibers.

Fiber core mode leakage induced by refractive index variation in high-power fiber laser

This paper presents an investigation of specific optical fiber core mode leakage behavior that occurs in high-power double-clad fiber lasers as a result of thermally-induced refractive index variations. A model of the power transfer between the core modes and the cladding modes during thermally-induced refractive index variations is established based on the mode coupling theory. The results of numerical simulations based on actual laser parameters are presented. Experimental measurements were also carried out, the results showed good agreement with the corresponding simulation results.

Design of Photonic Crystal Fiber Capable of Carrying Multiple Orbital Angular Momentum Modes Transmission

For the traditional photonic crystal fibers with circular air holes, rectangular air holes are added to the fiber cladding. The periodic arrangement of the inner rectangular air holes allows the fiber structure to better match the annular mode field distribution of the vortex beam. The fiber structure was analyzed and calculated by COMSOL Multiphysics 5.4 finite element software, and the characteristics of fiber were analyzed, such as the dispersion, confinement loss, effective mode area and nonlinear coefficient. The results reveal that the photonic crystal fiber structure capable of carrying 50 orbital angular momentum (OAM) modes at the wavelength of 1.15 to 2.0 μm (850 nm). The effective refractive index difference Δneff between vector modes can reach 1 × 10-3, and larger difference can effectively separate the vector modes and improve the transmission performance of OAM modes. Moreover, the fiber has good performance, such as flat dispersion distribution of the low-order modes, low confinement loss below 10-9 dB·m-1, large effective mode field area and small nonlinear coefficient in the 850 nm wavelength range. Therefore, this fiber structure can be applied to the high-capacity communication system of fiber multiplexing OAM. In addition, the good characteristics of this fiber structure are of great significance for the transmission of vortex beam in fiber.

An all-polarization-maintaining repetition-tunable erbium-doped passively mode-locked fiber laser

An environmentally stable, repetition rate tunable, all-polarization-maintaining, Er-doped pulse fiber laser with a single-wall carbon nanotubes saturated absorber is demonstrated. The ring laser cavity includes a delay line enabling a tunable repetition rate to vary from 35.52 MHz to 35.64 MHz with continuous mode-locked operation. The laser output parameters confirm that the tunable mode-locked operations are stable. High environmental stability is also confirmed by the -130 dBc/Hz low phase noise, a 70-dB signal-to-noise ratio of radio frequency signals, a low amplitude fluctuation of 5.76 × 10-4, and a low fluctuation of reoetition rate of 12 Hz. The laser shows a high de^ree of oolarization of 93%.

STABILITY ANALYSIS IN SPATIAL MODE FOR CHANNEL FLOW OF FIBER SUSPENSIONS

Different from previous temporal evolution assumption, the spatially growing mode was employed to analyze the linear stability for the channel flow of fiber suspensions. The stability equation applicable to fiber suspensions was established and solutions for a wide range of Reynolds number and angular frequency were given numerically . The results show that, the flow instability is governed by a parameter H which represents a ratio between the axial stretching resistance of fiber and the inertial force of the fluid. An increase of H leads to a raise of the critical Reynolds number, a decrease of corresponding wave number, a slowdown of the decreasing of phase velocity , a growth of the spatial attenuation rate and a diminishment of the peak value of disturbance velocity. Although the unstable region is reduced on the whole, long wave disturbances are susceptible to fibers.

Fiber laser pumped burst-mode operated picosecond mid-infrared laser

We demonstrate a compact periodically poled MgO-doped lithium niobate（MgO：PPLN）-based optical parametric oscillator（OPO） quasi-synchronously pumped by a fiber laser system with burst-mode operation.The pump source is a peak-power-selectable pulse-multiplied picosecond Yb fiber laser.The chirped pulses from a figure of eight-cavity modelocked fiber laser seed are narrowed to a duration of less than 50 ps using an FBG reflector and a circulator.The narrowed pulses are directed to pass through a pulse multiplier and to form pulse bunches,each of which is composed of 13 subpulses.The obtained pulse bunches are amplified by two-stage fiber pre-amplifiers：one-stage is core-pumped and the other is cladding-pumped.A fiberized acousto-optic modulator is inserted to control the pulse repetition rate（PRR） of the pulse bunches before they are power-amplified in the final amplifier stage with a large mode area（LMA） PM Yb-doped fiber.The maximum average powers from the final amplifier are 85 W,60 W,and 45 W,respectively,corresponding to the PRR of2.72 MHz,1.36 MHz,and 0.68 MHz.The amplified pulses are directed to pump an MgO：PPLN-based optical parametric oscillator（OPO）.A maximum peak power at 3.45 μm is obtained approximately to be 8.4 kW.Detailed performance characteristics are presented.

Suppression of Cladding Mode Coupling by B/Ge Codoped Photosensitive Fiber With Photosensitive and Depressed Inner Cladding

Excess loss on the short wavelength side of the Bragg resonant wavelength caused by cladding mode coupling limits wide use of grating in the fiber communication system, especially in densed wavelength division multiplexing (DWDM) system. A novel photosensitive fiber design that have depressed cladding and photosensitive inner cladding in the same fiber is proposed, which can suppress cladding mode coupling greatly. Using MCVD method B/Ge codoped fiber with depressed cladding was fabriceted out, which was also doped in boron and germanium and had the photosensitivity. Finally, the transmission spectrum of written grating in this fiber by phase mask method verified its larger photosensitivity and greatly suppression of cladding mode coupling.

Acoustic Response and Micro-Damage Mechanism of Fiber Composite Materials under Mode-Ⅱ Delamination

Realizing the accurate characterization for the dynamic damage process is a great challenge. Here we carry out testing simultaneously for dynamic monitoring and acoustic emission （AE） statistical analysis towards fiber composites under mode-Ⅱ delamination damage. The load curve, AE relative energy, amplitude distribution, and amplitude spectrum are obtained and the delamination damage mechanism of the composites is investigated by the microscopic observation of a fractured specimen. The results show that the micro-damage accumulation around the crack tip region has a great effect on the evolutionary process of delamination. AE characteristics and amplitude spectrum represent the damage and the physical mechanism originating from the hierarchical microstructure. Our finding provides a novel aud feasible strategy to simultaneously evaluate the dynamic response and micro-damage mechanism for fiber composites.