High-Power Raman Soliton Generation at 1.7 μm in All-Fiber Polarization-Maintaining Erbium-Doped Amplifier

An all-fiber polarization maintaining high-power laser system operating at 1.7 μm based on the Ramaninduced soliton self-frequency shifting effect is demonstrated. The entirely fiberized system is built by erbiumdoped oscillator and two-stage amplifiers with polarization maintaining commercial silica fibers and devices, which can provide robust and stable soliton generation. High-power soliton laser with the average power of 0.28 W,the repetition rate of 42.7 MHz, and pulse duration of 515 fs is generated directly from the main amplifier.Our experiment provides a feasible method for high-power all-fiber polarization maintaining femtosecond laser generation working at 1.7 μm.

Broadband Dual-Input Doherty Power Amplifier Design Based on a Simple Adaptive Power Dividing Ratio Function

In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.

A Hybrid Integrated and Low-Cost Multi-Chip Broadband Doherty Power Amplifier Module for 5G Massive MIMO Application

In this paper,a hybrid integrated broadband Doherty power amplifier(DPA)based on a multi-chip module(MCM),whose active devices are fabricated using the gallium nitride(GaN)process and whose passive circuits are fabricated using the gallium arsenide(GaAs)integrated passive device(IPD)process,is proposed for 5G massive multiple-input multiple-output(MIMO)application.An inverted DPA structure with a low-Q output network is proposed to achieve better bandwidth performance,and a single-driver architecture is adopted for a chip with high gain and small area.The proposed DPA has a bandwidth of 4.4-5.0 GHz that can achieve a saturation of more than 45.0 dBm.The gain compression from 37 dBm to saturation power is less than 4 dB,and the average power-added efficiency(PAE)is 36.3%with an 8.5 dB peak-to-average power ratio(PAPR)in 4.5-5.0 GHz.The measured adjacent channel power ratio(ACPR)is better than50 dBc after digital predistortion(DPD),exhibiting satisfactory linearity.

Harmonic balance simulation of the influence of component uniformity and reliability on the performance of a Josephson traveling wave parametric amplifier

A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.

Three-channel CMOS transimpedance amplifier for LiDAR sensor receiver

For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input stage is at the core of the complementary metal oxide semiconductor(CMOS)circuit chip,giving it more immunity to input photodiode detectors.A simple smart output interface acting as a feedback structure,which is rarely found in other designs,reduces the chip size and power consumption simultaneously.The circuit is designed using a 0.5μm CMOS process technology to achieve low cost.The device delivers a 33.87 dB?transimpedance gain at 350 MHz.With a higher input load capacitance,it shows a-3 dB bandwidth of 461 MHz,indicating a better detector tolerance at the front end of the system.Under a 3.3 V supply voltage,the device consumes 5.2 mW,and the total chip area with three channels is 402.8×597.0μm2(including the test pads).

High-gain integrated in-line few-mode amplifier enabling 3840-km long-haul transmission

An integrated few-mode erbium-doped fiber amplifier(FM-EDFA)with high modal gain is suitable for the in-line amplification in mode-division multiplexing transmission(MDM)systems.We first experimentally demonstrate a dual-stage integrated FM-EDFA supporting three linear polarization modes.Consisting of integrated passive components with low insertion losses,the FM-EDFA has a similar structure and performance to widely used commercial single-mode EDFAs.The averaged modal gain of 25 dB,the differential modal gain(DMG)of<1.1 dB,and noise figures of 5–7 dB are simultaneously achieved.In addition,the DMG of the 3M-EDF itself is~0.3 dB.Moreover,an MDM transmission experiment with the in-line few-mode amplification by our proposed FM-EDFA over a 3840-km few-mode fiber link for a 28-Gbaud quadrature phase-shift keying(QPSK)signal is demonstrated.

Design and performance of a high-speed and low-noise preamplifier for SiPM

Considering the R&D for upgrading the K^(0)_(L) andμdetectors in the Belle II experiment using a scintillator and silicon pho-tomultiplier(SiPM),we designed a compact high-speed and low-noise preamplifier.The preamplifier demonstrated a good gain stability,bandwidth of 426 MHz,baseline noise level ofσ≈0.6 mV,dynamic range of up to170 mV of the input signal amplitude,good time resolution of 20 ps,and it can be comprehensively applied to SiPMs.Adopting pole-zero-cancelation in the preamplifier reduces both the rise and fall times of the SiPM signal,which can significantly improve the time resolution and reduce the pile-up when using a large SiPM or an array of SiPMs.Various combinations of the preamplifier and several types of SiPMs demonstrated time resolutions better than 50 ps for most cases;when the number of detected photons was larger than 60,a time resolution of approximately 25 ps was achieved.

5G Wideband Bandpass Filtering Power Amplifiers Based on a Bandwidth-Extended Bandpass Matching Network

In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.

Wavelength switchable mode-locked fiber laser with a few-mode fiber filter

We have proposed and constructed a few-mode fiber(FMF)-based comb filter realized by dislocation splicing a fewmode long-period fiber grating(FM-LPFG) with a single-mode fiber(SMF). From an all-fiber laser with a FMF-based comb filter, the generation of switchable single-, dual-, triple-, and quadruple-wavelength continuous light has been achieved.Moreover, wavelength switchable mode-locked pulses have been obtained with the increased pump power. In the experiment, the output wavelength of the mode-locked fiber laser was changed from 1567.72 nm to 1571.04 nm, while the signal-to-noise(SNR) ratio was maintained above 61 d B. The switchable multiwavelength continuous wave(CW) and mode-locked all-fiber lasers have potentially important applications for fiber sensing, wavelength-division multiplexing(WDM) and signal processing.

Impact of amplified spontaneous emission noise on the SRS threshold of high-power fiber amplifiers

Impact of amplified spontaneous emission(ASE)noise on the stimulated Raman scattering(SRS)threshold of highpower fiber amplifiers is demonstrated numerically through a spectral evolution approach.The simulation results confirm that ASE noise in the Raman wavelength band could reduce the SRS threshold of high-power fiber amplifiers significantly.As for ASE noise originated the main amplifier,it becomes stronger and reduces the SRS threshold at shorter operation wavelength below 1052 nm.As for ASE noise originated from the seed laser,it reduces the SRS threshold at different operation wavelength under the condition that the Raman ratio is over-90 dB in the seed laser.The theoretical method and results in this work could provide a well reference to extend the operation wavelength of high-power fiber lasers.

Machine Learning-based Inverse Model for Few-Mode Fiber Designs

The medium for next-generation communication is considered as fiber for fast,secure communication and switching capability.Mode division and space division multiplexing provide an excellent switching capability with high data transmission rate.In this work,the authors have approached an inverse modeling technique using regression-based machine learning to design a weakly coupled few-mode fiber for facilitating mode division multiplexing.The technique is adapted to predict the accurate profile parameters for the proposed few-mode fiber to obtain the maximum number of modes.It is for a three-ring-core few-mode fiber for guiding five,ten,fifteen,and twenty modes.Three types of regression models namely ordinary least-square linear multi-output regression,k-nearest neighbors of multi-output regression,and ID3 algorithm-based decision trees for multi-output regression are used for predicting the multiple profile parameters.It is observed that the ID3-based decision tree for multioutput regression is the robust,highly-accurate machine learning model for fast modeling of FMFs.The proposed fiber claims to be an efficient candidate for the next-generation 5G and 6G backhaul networks using mode division multiplexing.

Improving source-in-the-middle continuous-variable quantum key distribution using a heralded hybrid linear amplifier

A hybrid linear amplifier is inserted at the output of the source-in-the-middle distribution protocol to overcome the shortcomings of the transmission distance.The modified protocol aims to maintain a high key rate for long-distance transmission under high noise.It has the potential to significantly broaden the application range of the continuous variable quantum key distribution protocol.The effects of amplifier parameters and noise on the modified protocol are analyzed in detail with regard to applying it to a practical system.To make the simulation more realistic,the effect of finite size on the new protocol is taken into account.It will serve as a guideline for the future use of hybrid linear amplifiers.Different parameters can be adjusted to achieve the best performance for key rates of different quantum channels.

Piezomagnetic vibration energy harvester with an amplifier

We study the effect of an amplification mechanism in a nonlinear vibration energy harvesting system where a ferromagnetic beam resonator is attached to the vibration source through an additional linear spring with a damper.The beam moves in the nonlinear double-well potential caused by interaction with two magnets.The piezoelectric patches with electrodes attached to the electrical circuit support mechanical energy transduction into electrical power.The results show that the additional spring can improve energy harvesting.By changing its stiffness,we observed various solutions.At the point of the optimal stiffness of the additional spring,the power output is amplified a few times depending on the excitation amplitude.

Research Towards Terahertz Power Amplifiers in Silicon-Based Process

In view of the existing design challenges for Terahertz(THz)power amplifiers(PAs),the common design methods and the efforts of the State Key Laboratory of Millimeter Wave,Southeast University,China in the development of silicon-based THz PAs,mainly including silicon-based PAs with operating frequencies covering 100–300 GHz,are summarized in this paper.Particularly,we design an LC-balun-based two-stage differential cascode PA with a center frequency of 150 GHz and an output power of 14 dBm.Based on a Marchand balun,we report a 220 GHz three-stage differential cascode PA with a saturated output power of 9.5 dBm.To further increase the output power of THz PA,based on a four-way differential power combining technique,we report a 211–263 GHz dual-LC-tank-based broadband PA with a recorded 14.7 dBm Psat and 16.4 dB peak gain.All the above circuits are designed in a standard 130 nm silicon germanium(SiGe)BiCMOS process.

Vertical vibration control using nonlinear energy sink with inertial amplifier

To reduce additional mass, this work proposes a nonlinear energy sink(NES)with an inertial amplifier(NES-IA) to control the vertical vibration of the objects under harmonic and shock excitations. Moreover, this paper constructs pure nonlinear stiffness without neglecting the gravity effect of the oscillator. Both analytical and numerical methods are used to evaluate the performance of the NES-IA. The research findings indicate that even if the actual mass is 1% of the main oscillator, the NES-IA with proper inertia angles and mass distribution ratios can still effectively attenuate the steady-state and transient responses of the main oscillator. Nonlinear stiffness and damping also have important effects. Due to strongly nonlinear factors, the coupled system may exhibit higher branch responses under harmonic excitation. In shock excitation environment, the NES-IA with a large dynamic mass can trigger energy capture of both main resonance and high-frequency resonance. Furthermore, the comparison with the traditional NES also confirms the advantages of the NES-IA in overcoming mass dependence.

On-chip integrated few-mode erbium–ytterbium co-doped waveguide amplifiers

We propose for the first time,to the best of our knowledge,an on-chip integrated few-mode erbium–ytterbium co-doped waveguide amplifier based on an 800 nm thick Si_(3)N_(4)platform,which demonstrates high amplification gains and low differential modal gains(DMGs)simultaneously.An eccentric waveguide structure and a co-propagating pumping scheme are adopted to balance the gain of each mode.A hybrid mode/polarization/wavelengthdivision(de)multiplexer with low insertion loss and crosstalk is used for multiplexing and demultiplexing in two operation wavebands centered at 1550 nm and 980 nm,where the light in these two bands serves as the signal light and pump light of the amplifier,respectively.The results demonstrate that with an input signal power of 0.1 mW,TE_(0)mode pump power of 300 mW,and TE_(1)mode pump power of 500 m W,the three signal modes(TE_(0)∕TM_(0)∕TE_(1))all exhibit amplification gains exceeding 30 dB,while maintaining a DMG of less than 0.1 dB.

Low-modal-crosstalk doped-fiber amplifiers in few-mode-fiber-based systems

Independent light propagation through one or multiple modes is commonly considered as a basic demand for mode manipulation in few-mode fiber(FMF)-or multimode fiber(MMF)-based optical systems such as transmission links,optical fiber lasers,or distributed optical fiber sensors.However,the insertion of doped-fiber amplifiers always kills the entire effort by inducing significant modal crosstalk.In this paper,we propose the design of doped-fiber amplifiers in FMF-based systems adopting identical multiple-ring-core(MRC)index profiles for both passive and doped fibers to achieve low modal crosstalk.We develop the direct-glass-transition(DGT)modified chemical vapor deposition(MCVD)processing for precise fabrication of few-mode erbium-doped fibers(FM-EDFs)with MRC profiles of both refractive index and erbium-ion doping distribution.Then,a few-mode erbium-doped-fiber amplifier(FM-EDFA)with a maximum gain of 26.08 dB and differential modal gain(DMG)of 2.3 dB is realized based on fabricated FM-EDF matched with a transmission FMF supporting four linearly polarized(LP)modes.With the insertion of the FM-EDFA,60+60 km simultaneous LP_(01)∕LP_(11)∕LP_(21)∕LP_(02)transmission without inter-modal multiple-input multiple-output digital signal processing(MIMO-DSP)is successfully demonstrated.The proposed design of low-modal-crosstalk doped-fiber amplifiers provides,to our knowledge,new insights into mode manipulation methods in various applications.

Nonlinear Absorption and Low-threshold Two-photon Pumped Amplified Stimulated Emission from FAPbBr_(3) Nanocrystals

Formamidinium lead bromide(FAPbBr_(3))nanocrystals(NCs)have been considered to be a good optoelectronic material due to their pure green emission,excellent stability and superior carrier transport characteristics.However,two-photon pumped amplified spontaneous emission(ASE)and the corresponding nonlinear optical properties of FAPbBr_(3) NCs are scarcely revealed.Herein,we synthesized colloidal FAPbBr_(3) NCs with different sizes by changing the molar ratio of FABr/PbBr_(2) in the precursor solution,using ligand assisted precipitation(LARP)technology at room temperature.Photoluminescence(PL)and time resolved photoluminescence(TRPL)spectroscopy were measured to characterize their ASE properties.And their nonlinear optical properties were studied through the Zscan technique and the two-photon excited fluorescence method.The stimulated emission properties including oneand two-photon pumped ASE have been realized from FAPbBr_(3) NCs.With large two-photon absorption coefficient(0.27 cm/GW)and high non-linear absorption cross-section(7.52×10^(5) GM),ASE with threshold as low as 9.8μJ/cm^(2) and 487μJ/cm^(2) have been obtained from colloidal FAPbBr_(3) NCs using one-and two-photon excitations.These results indicate that as a new possible green-emitting frequency-upconversion material with low thresholds,FAPbBr_(3) NCs hold great potential in the development of high-performance two-photon pump lasers.

Step memory polynomial predistorter for power amplifiers with memory

To reduce the number of digital predistortion coefficients, a step memory polynomial （SMP）predistorter is presented. The number of predistortion coefficients is decreased by adjusting the maximum nonlinear order for different memory orders in the traditional memory polynomial （MP）predistorter. The proposed SNIP predistorter is identified by an offline learning structure on which the coefficients can be extracted directly from the sampled input and output of a PA. Simulation results show that the SMP predistorter is not tied to a particular PA model and is, therefore, robust. The effectiveness of the SMP predistorter is demonstrated by simulations and experiments on an MP model, a parallel Wiener model, a Wiener-Hammerstein model, a sparsedelay memory polynomial model and a real PA which is fabricated based on the Freescale LDMOSFET MRF21030. Compared with the traditional MP predistorter, the SMP predistorter can reduce the number of coefficients by 60%.

Single Event Transients of Operational Amplifier and Optocoupler

The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent LET is tested,the sensitive areas of the SET effects are identified in voltage follower application mode of LM124J, and the mechanism is initially analyzed. The transient amplitude and duration of HCPL5231 at various equivalent LET are examined,and the SET cross-section is measured. The results of our test and heavy ion experimental data coincide closely,indicating that a pulsed laser test facility is a valid tool for single event effect evaluation.