980-nm all-fiber mode-locked Yb-doped phosphate fiber oscillator based on semiconductor saturable absorber mirror and its amplifier

A 980-nm semiconductor saturable absorber mirror（SESAM） mode-locked Yb-doped phosphate fiber laser is demonstrated by using an all-fiber linear cavity configuration. Two different kinds of cavity lengths are introduced into the oscillator to obtain a robust and stable mode-locked seed source. When the cavity length is chosen to be 6 m, the oscillator generates an average output power of 3.5 m W and a pulse width of 76.27 ps with a repetition rate of 17.08 MHz. As the cavity length is optimized to short, 4.4-m W maximum output power and 61.15-ps pulse width are produced at a repetition rate of 20.96 MHz. The output spectrum is centered at 980 nm with a narrow spectral bandwidth of 0.13 nm. In the experiment, no undesired amplified spontaneous emission（ASE） nor harmful oscillation around 1030 nm is observed. Moreover,through a two-stage all-fiber-integrated amplifier, an output power of 740 m W is generated with a pulse width of 200 ps.

Evolution of modes in double-clad Raman fiber amplifier

Stimulated Raman scattering in a double cladding optical fiber is studied with a continuous wave laser used as a pump source. Under various launch conditions, pump modes are differently excited. Considering the mode coupling effect among the pump modes, the evolution of the power in the Stokes modes is studied. The results show that the scattered waves （the Stokes waves） in the fiber core with 9%tm diameter and 0.14 NA could propagate predominantly in the fundamental mode of the fiber by carefully adjusting the pump light launching conditions.

Thermal expanded core technique applied to high power fiber mode field adapter

A mode field adapter （MFA） fabricated by the thermal expanded core （TEC） technique is investigated. Firstly, the mode field characteristics of the TEC large mode area fiber （LMAF） are analyzed. Compared with the single-mode fiber （SMF）, the mode field diameter of the LMAF enlarged slower than that of the SMF. Secondly, the mode field characteristics of the different fibers with TEC treatment are discussed. Thirdly, the transmission efficiency of the MFA fabricated by the SMF and LMAF is also investigated. Finally, we used the 6/125 μm SMF and 15/130 μm LMAF to fabricate an MFA with transmission efficiency of 92% and the handling power as high as 100 W.

Generation and evolution of multiple operation states in passively mode-locked thulium-doped fiber laser by using a graphene-covered-microfiber

Using graphene-covered-microfiber （GCM） as a saturable absorber, the generation and evolution of multiple operation states are proposed and demonstrated in passively mode-locked thulium-doped fiber laser. The microfiber was fabricated using the flame brushing method to an interaction length of - 1.2 cm with a waist diameter of -10 μm. Graphene layers were grown on copper foils by chemical vapor deposition and transferred onto the polydimethylsiloxane （PDMS） to form a PDMS/graphene film, which allowed light-graphene interaction via evanescent field. With the increase of the pump power from 1.25 W to 2.15 W, five different lasing regimes, including continuous-wave, conventional soliton mode-locking, multi- soliton mode-locking, a period of transition, and noise-like mode-locking, were achieved in a fiber ring cavity. To the best of our knowledge, it is the first report of the generation and evolution of multiple operation states by covering graphene on the microfiber in the 2-μ.m region. The results demonstrate that GCM can be a promising method for fabricating all fiber SA, and the switchable operation states can provide more portability in complex application domain.

Interference of selective higher-order modes in optical fibers

The interference of selective higher-order modes in optical fibers is investigated both theoretically and experimentally. It has been demonstrated that by coupling the LP01 mode in a step-index single-mode fiber (SMF) to the LP0m modes in step-index multimode fibers (MMFs) with different parameters, one can selectively generate higher-order modes and construct all-fiber interferometers. The research presented in this paper forms a basis of a new type of fiber devices with potential applications in fiber sensing, optical fiber communications, and optical signal processing.

Pulse-train nonuniformity in an all-fiber ring laser passively mode-locked by nonlinear polarization rotation

This paper reports the periodic power variation of the pulse-train in a passively mode-locked soliton fiber ring laser. It can obtain either the uniform or nonuniform pulse-train output by simply rotating the polarization controllers. The experimental results show that the pulse-train nonuniformity is caused by the interaction between the nonuniform polarization states of the soliton pulses and the passive polarizer in the cavity.

Acoustic Response and Micro-Damage Mechanism of Fiber Composite Materials under Mode-Ⅱ Delamination

Realizing the accurate characterization for the dynamic damage process is a great challenge. Here we carry out testing simultaneously for dynamic monitoring and acoustic emission （AE） statistical analysis towards fiber composites under mode-Ⅱ delamination damage. The load curve, AE relative energy, amplitude distribution, and amplitude spectrum are obtained and the delamination damage mechanism of the composites is investigated by the microscopic observation of a fractured specimen. The results show that the micro-damage accumulation around the crack tip region has a great effect on the evolutionary process of delamination. AE characteristics and amplitude spectrum represent the damage and the physical mechanism originating from the hierarchical microstructure. Our finding provides a novel aud feasible strategy to simultaneously evaluate the dynamic response and micro-damage mechanism for fiber composites.

The effect of fractional thermoelasticity on a two-dimensional problem of a mode I crack in a rotating fiber-reinforced thermoelastic medium

This article is concerned with the effect of rotation on the general model of the equations of the generalized thermoe- lasticity for a homogeneous isotropic elastic half-space solid, whose surface is subjected to a Mode-I crack problem. The fractional order theory of thermoelasticity is used to obtain the analytical solutions for displacement components, force stresses, and temperature. The boundary of the crack is subjected to a prescribed stress distribution and temperature. The normal mode analysis technique is used to solve the resulting non-dimensional coupled governing equations of the problem. The variations of the considered variables with the horizontal distance are illustrated graphically. Some particular cases are also discussed in the context of the problem. Effects of the fractional parameter, reinforcement, and rotation on the varia- tions of different field quantities inside the elastic medium are analyzed graphically. Comparisons are made between the results in the presence and those in the absence of fiber-reinforcing, rotating and fractional parameters.

Mode-locked fiber laser with MoSe_2 saturable absorber based on evanescent field

An all-fiber mode-locked fiber laser was achieved with a saturable absorber based on a tapered fiber deposited with layered molybdenum selenide(MoSe_2). The laser was operated at a central wavelength of 1558.35 nm with an output spectral width of 2.9 nm, and a pulse repetition rate of 16.33 MHz. To the best of our knowledge, this is the first report on mode-locked fiber lasers using MoSe_2 saturable absorbers based on tapered fibers.

Self-starting all-fiber PM Er:laser mode locked by a biased nonlinear amplifying loop mirror

A compact all-fiber polarization-maintaining Er:laser using a nonlinear amplifying loop mirror is reported. Fundamental single-pulse mode-locking operation can always self start, with a cavity round-trip decreased from ~ 4.7 m to~ 1.7 m. When the pulse repetition rate is 121.0328 MHz, output pulse is measured to have a center wavelength/3-d B spectral bandwidth/radio frequency signal to noise ratio(SNR)/pulse width of 1571.65 nm/18.70 nm/80 d B/477 fs, respectively. Besides, three states including the exponential growth, damping state, and steady state are investigated through the build-up process both experimentally and numerically. Excellent stability of this compact Er:laser is further evaluated,demonstrating that it can be an easy-fabrication maintenance-free ultrafast candidate for the scientific area of this kind.

Reduced graphene oxide as saturable absorbers for erbium-doped passively mode-locked fiber laser

We demonstrate a nanosecond mode-locked erbium-doped fiber laser （EDFL） based on a reduced graphene oxide （RGO） saturable absorber （SA）. The RGO SA is prepared by depositing the graphene oxide （GO） on fluorine mica through thermal reduction of GO. A scanning electron microscope （SEM）, Raman spectrometer, and x-ray photoelectron spec- troscopy （XPS） are adopted to analyze the RGO characteristics. The results show that the reduction degree of graphene oxide is very high. By embedding the RGO SA into the EDFL cavity, a stable mode-locked fiber laser is achieved with a central wavelength of 1567.29 nm and repetition rate of 12.66 MHz. The maximum output power and the minimum pulse duration are measured to be 18.22 mW and 1.38 ns respectively. As far as we know, the maximum output power of 18.22 mW is higher than those of other nanosecond mode-locked oscillators reported. Such a nanosecond pulse duration and megahertz repetition rate make this mode-locked erbium-doped fiber laser a suitable seed oscillator for high-power applications and chirped pulse amplifications.

Carboxyl graphene oxide solution saturable absorber for femtosecond mode-locked erbium-doped fiber laser

The carboxyl-functionalized graphene oxide（GO-COOH） is a kind of unique two-dimensional（2 D） material and possesses excellent nonlinear saturable absorption property and high water-solubility. In this paper, we prepare saturable absorber（SA） device by depositing GO-COOH nanosheets aqueous solution on a D-shaped fiber. The modulation depth（MD） and saturable intensity of the SA are measured to be 9.6% and 19 MW/cm^2, respectively. By inserting the SA into the erbium-doped fiber（EDF） laser, a passively mode-locked EDF laser has been achieved with the spectrum center wavelength of 1562.76 nm. The pulse duration, repetition rate, and the signal-to-noise ratio（SNR） are 500 fs, 14.79 MHz, and 80 dB,respectively. The maximum average output power is measured to be 3.85 mW. These results indicate that the GO-COOH nanosheets SA can be used as a promising mode locker for the generation of ultrashort pulses.

Optical Pulse Compression Based on High-doped Erbium Fiber Amplifier and Standard Single-mode Fiber

Proposed is a novel optical pulse compression technique based on high-doped erbium fiber amplifier and standard single-mode fiber(SMF). We used the amplifier with the erbium ion concentration of 6.3×10-3 to amplify a hyperbolic secant pulse from a regeneratively mode-locked fiber laser. The central wavelength, pulsewidth and peak power of the pulse are 1 550 nm, 12.5 ps and 3 mW, respectively. Then the amplified pulse with peak power level corresponding to a higher-order soliton is compressed when it propagates through a 3-km-long single-mode fiber. Studied are the compressed pulses under different pump powers and fiber lengths. The results show that it can get a narrower pulse, and solve the difficulty that pulses at low power can not be compressed directly in the fiber. And the construct is compact.

Fiber laser pumped burst-mode operated picosecond mid-infrared laser

We demonstrate a compact periodically poled MgO-doped lithium niobate（MgO：PPLN）-based optical parametric oscillator（OPO） quasi-synchronously pumped by a fiber laser system with burst-mode operation.The pump source is a peak-power-selectable pulse-multiplied picosecond Yb fiber laser.The chirped pulses from a figure of eight-cavity modelocked fiber laser seed are narrowed to a duration of less than 50 ps using an FBG reflector and a circulator.The narrowed pulses are directed to pass through a pulse multiplier and to form pulse bunches,each of which is composed of 13 subpulses.The obtained pulse bunches are amplified by two-stage fiber pre-amplifiers：one-stage is core-pumped and the other is cladding-pumped.A fiberized acousto-optic modulator is inserted to control the pulse repetition rate（PRR） of the pulse bunches before they are power-amplified in the final amplifier stage with a large mode area（LMA） PM Yb-doped fiber.The maximum average powers from the final amplifier are 85 W,60 W,and 45 W,respectively,corresponding to the PRR of2.72 MHz,1.36 MHz,and 0.68 MHz.The amplified pulses are directed to pump an MgO：PPLN-based optical parametric oscillator（OPO）.A maximum peak power at 3.45 μm is obtained approximately to be 8.4 kW.Detailed performance characteristics are presented.

STABILITY ANALYSIS IN SPATIAL MODE FOR CHANNEL FLOW OF FIBER SUSPENSIONS

Different from previous temporal evolution assumption, the spatially growing mode was employed to analyze the linear stability for the channel flow of fiber suspensions. The stability equation applicable to fiber suspensions was established and solutions for a wide range of Reynolds number and angular frequency were given numerically . The results show that, the flow instability is governed by a parameter H which represents a ratio between the axial stretching resistance of fiber and the inertial force of the fluid. An increase of H leads to a raise of the critical Reynolds number, a decrease of corresponding wave number, a slowdown of the decreasing of phase velocity , a growth of the spatial attenuation rate and a diminishment of the peak value of disturbance velocity. Although the unstable region is reduced on the whole, long wave disturbances are susceptible to fibers.

Wavelength dependent loss of splice of single-mode fibers

After reviewing three different definitions of mode field diameter of single-mode fibers, coupled efficiency calculation methods associated with lateral offset, longitude separation and wavelength, the effects produced by them, and the influences of splicing defects were discussed in detail. The regularities of the effects were studied according to the first order derivation of couple efficiency formula, and a simplified formula for couple efficiency calculation was presented under the circumstance of slight misalignment, with respect to wavelength, λ, and in a good agreement with the theoretical model. The simplified formula provides a new but simple approach to evaluate wavelength dependent couple efficiency of single-mode fibers. Theoretical analyses and numerical calculations show that, when those defects exist, the wavelength produces additional effects on the couple loss that growth of wavelength causes an increase on the couple efficiency for the lateral offset or longitude separation whereas lessens the couple efficiency due to angular misalignment or mode fields mismatching, and that the wavelength degrades the couple efficiency distinctly when λ≥ 2.5 μm whereas it distorts the couple slightly in range of λ c ≤λ≤2 μm.

Interaction of a parabolic-shaped pulse pair in a passively mode-locked Yb-doped fiber laser

We numerically investigate the formation and interaction of a parabolic-shaped pulse pair in a passively mode-locked Yb-doped fiber laser. Based on a lumped model, the parabolic-shaped pulse pair is obtained by controlling the intercavity average dispersion and gain saturation energy, Moreover, pulse repulsive and attractive motion are also achieved with different pulse separations. Simulation results show that the phase shift plays an important role in pulse interaction, and the interaction is determined by the inter-cavity average dispersion and gain saturation energy, i.e., the strength of the interaction is proportional to the gain saturation energy, a stronger gain saturation energy will result in a higher interaction intensity. On the contrary, the increase of the inter-cavity dispersion will counterbalance some interaction force. The results also show that the interaction of a parabolic-shaped pulse pair has a larger interaction distance compared to conventional solitons.

An all-polarization-maintaining repetition-tunable erbium-doped passively mode-locked fiber laser

An environmentally stable, repetition rate tunable, all-polarization-maintaining, Er-doped pulse fiber laser with a single-wall carbon nanotubes saturated absorber is demonstrated. The ring laser cavity includes a delay line enabling a tunable repetition rate to vary from 35.52 MHz to 35.64 MHz with continuous mode-locked operation. The laser output parameters confirm that the tunable mode-locked operations are stable. High environmental stability is also confirmed by the -130 dBc/Hz low phase noise, a 70-dB signal-to-noise ratio of radio frequency signals, a low amplitude fluctuation of 5.76 × 10-4, and a low fluctuation of reoetition rate of 12 Hz. The laser shows a high de^ree of oolarization of 93%.

A novel method of evaluating large mode area fiber design by brightness factor

A novel evaluation term and a more reasonable criterion,which is described by a new parameter of brightness factor for active large mode area fiber design,are presented.The brightness factor evaluation method is based on the transverse mode competition mechanism in fiber lasers and amplifiers.The brightness factor can be seen as a description of fiber general property since it can represent the output laser brightness of the fiber laser system and because of its ability to resist the nonlinear effect.A core-doped active large pitch fiber with a core diameter of 190 μm and a mode-field diameter of180 μm is designed by this method,and the designed fiber allows effective single-mode operation.

Theoretical analysis of the mode coupling induced by heat of large-pitch micro-structured fibers

In this paper,a theoretical model to analyze the mode coupling induced by heat,when the fiber amplifier works at high power configuration,is proposed.The model mainly takes into consideration the mode field change due to the thermally induced refractive index change and the coupling between modes.A method to predict the largest average output power of fiber is also proposed according to the mode coupling theory.The largest average output power of a large pitch fiber with a core diameter of 190 μm and an available pulse energy of 100 mJ is predicted to be 540 W,which is the highest in large mode field fibers.