The enhancement of chemical absorption of CO2 by K2CO3/H2O absorbents in the presence of activated carbon （AC） particles was investigated. The results show that the gas absorption rates can be enhanced significantly...The enhancement of chemical absorption of CO2 by K2CO3/H2O absorbents in the presence of activated carbon （AC） particles was investigated. The results show that the gas absorption rates can be enhanced significantly in the presence of AC particles, and the maximum enhancement factor 3.7 was observed at low stirring intensities. The enhancement factor increased rapidly with the solid loading during the initial period of absorption and then be- came mild gradually to a maximum value. Both the liquid-solid contact area and the probability of solid particles residing at the gas-liquid interface decreased with the increase of the particle size, leading to a negative effect on the enhancement of mass transfer. The influence of the particles on gas absorption decreased with the reaction rate. The stirring speed changed the interfacial coverage and mass transfer rate on the liquid side and consequently affected the mass transfer between the gas and liquid phases; the enhancement factor decreased with the stirring intensity. A heterogeneous two-zone model was proposed for predicting the enhancement factor and the calculated results agreed well with the experimental data.展开更多
The online flow injection preconcentration and electrothermal atomic absorption spectrometry method were used for the determination of trace nickel in electrolytic manganese samples by sorption on a conical minicolumn...The online flow injection preconcentration and electrothermal atomic absorption spectrometry method were used for the determination of trace nickel in electrolytic manganese samples by sorption on a conical minicolumn packed with activated carbon at pH 9.0. The nickel was eluted from the minicolumn with 10%(v/v) nitric acid. An enrichment factor of 190-fold for a sample volume of 10mL was obtained. The detection limit (DL) of nickel with the use of the preconcentration method was 13ng·g -1in the original solid sample. The precision for 10 replicate determinations at 150ng·g -1 nickel concentration was 5.2% relative standard deviation (RSD). The calibration graph was linear with a correlation coefficient of r=0.9996 up to concentration of 660ng·g -1 nickel.展开更多
There has recently been a fundamental need to develop high efficiency microwave absorbers to reduce electro-magnet-ic pollution.It is often very difficult to obtain superior absorption with only one material,so we hav...There has recently been a fundamental need to develop high efficiency microwave absorbers to reduce electro-magnet-ic pollution.It is often very difficult to obtain superior absorption with only one material,so we have explored composites using fillers of activated carbon derived from biological material(oleaster seeds)and resin(apricot tree gum)with Fe_(3)O_(4) in a paraffin wax matrix to improve the dielectric properties and achieve a high specific surface area.A 1 mm thick layer of a Fe_(3)O_(4)+resin(FEOR),with the magnetic nanoparticles anchored to the gum,resulted in a reflection loss of−71.09 dB.We compared this with the results for composites using a filler of Fe_(3)O_(4)+activated carbon,and one with a three-component filler of Fe_(3)O_(4)+activated carbon+resin which had a very porous structure that had a direct effect on the surface polarization.However,the FEOR sample had near-ideal im-pedance matching,close to 1,which resulted in high absorption performance.In addition,the presence of defects improves mi-crowave attenuation by dipole polarization and charge carrier trapping.This work suggests the use of new types of biomaterials to in-crease microwave absorption.展开更多
In order to predict the damage behaviours of 3D-printed continuous carbon fibre(CCF)reinforced composites,when additional short carbon fibre(SCF)composite components are employed for continuous printing or special fun...In order to predict the damage behaviours of 3D-printed continuous carbon fibre(CCF)reinforced composites,when additional short carbon fibre(SCF)composite components are employed for continuous printing or special functionality,a novel path-dependent progressive failure(PDPF)numerical approach is developed.First,a progressive failure model using Hashin failure criteria with continuum damage mechanics to account for the damage initiation and evaluation of 3D-printed CCF reinforced polyamide(PA)composites is developed,based on actual fibre placement trajectories with physical measurements of 3D-printed CCF/PA constituents.Meanwhile,an elastic-plastic model is employed to predict the plastic damage behaviours of SCF/PA parts.Then,the accuracy of the PDPF model was validated so as to study 3D-printed CCF/PA composites with either negative Poisson's ratio or high stiffness.The results demonstrate that the proposed PDPF model can achieve higher prediction accuracies in mechanical properties of these 3D-printed CCF/PA composites.Mechanism analyses show that the stress distribution is generally aggregated in the CCF areas along the fibre placement paths,and the shear damage and matrix tensile/compressive damage are the key damage modes.This study provides a new approach with valuable information for characterising complex 3D-printed continuous fibre-matrix composites with variable mechanical properties and multiple constituents.展开更多
A simple and reliable method for the extraction and determination of trace amounts of copper（Ⅱ） ions using activated carbon （AC） impregnated by a new Schiff base 5-[（4-heptyloxyphenyl）azo]-N-（4-propyloxyphenyl...A simple and reliable method for the extraction and determination of trace amounts of copper（Ⅱ） ions using activated carbon （AC） impregnated by a new Schiff base 5-[（4-heptyloxyphenyl）azo]-N-（4-propyloxyphenyl）-salicylaldimine （HPPS） and atomic absorption spectrometry is presented. Recovery efficiency and the influence of pH value, volume of sample solution, effect of different eluents, and interfering ions were evaluated. The limit of detection （3σ） was 2.62 ng.mL^-1 and the relative standard deviation （n=10） was 1.5%. Under optimum conditions, the copper ions were concentrated 25 fold using 250 mL of sample solution and 10 mL of eluent. This procedure has been successfully applied to the determination of copper in different water samples.展开更多
Coconut-based activated carbons were modified with sodium dodecyl sulfate (SDS). The activated carbons, which were modified by different concentrations of SDS, were characterized by acid/base titrations, textural anal...Coconut-based activated carbons were modified with sodium dodecyl sulfate (SDS). The activated carbons, which were modified by different concentrations of SDS, were characterized by acid/base titrations, textural analysis (BET), atomic absorption spectrochemical analysis and Zeta potential measurements. The effects of SDS modification on Pb2+ absorption were studied further. The results indicate that after the modification of SDS, there are new functional groups on the surface of modified activated carbons and the number of functional group has changed remarkably, the total acidity decreases observably, but the total alkalinity increases dramatically. With the increase of surface load with SDS, the Pb2+ adsorption mass of activated carbons increases and the optimal pH for Pb2+ adsorption of the SDS modified activated carbons is 5. The experimental data are simulated better by Freundlich isotherm model for the modified activated carbons, and the experimental data are simulated better by Langmuir isotherm model for unmodified ones.展开更多
In present study,we report the preparation of coconut shell activated carbon as adsorbent and its appli-cation for Bi(Ⅲ) removal from aqueous solutions.The developed adsorbent was characterized with scanning elec-tro...In present study,we report the preparation of coconut shell activated carbon as adsorbent and its appli-cation for Bi(Ⅲ) removal from aqueous solutions.The developed adsorbent was characterized with scanning elec-tron microscope(SEM),Fourier Transform Infrared(FTIR),C,H,N,S analyzer,and BET surface area analyzer.The parameters examined include agitation time,initial concentration of Bi(Ⅲ),adsorbent dose and temperature.The maximum adsorption of Bi(Ⅲ)(98.72%) was observed at 250 mg·L-1 of Bi(Ⅲ) and adsorbent dose of 0.7 g when agitation was at 160 r·min-1 for 240 min at(299±2) K.The thermodynamic parameters such as Gibb's free energy(△Gθ),enthalpy(△Hθ) and entropy(△Sθ) were evaluated.For the isotherm models applied to adsorption study,the Langmuir isotherm model fits better than the Freundlich isotherm.The maximum adsorption capacity from the Langmuir isotherm was 54.35 mg?g?1 of Bi(Ⅲ).The kinetic study of the adsorption shows that the pseudo second order model is more appropriate than the pseudo first order model.The result shows that,coconut shell ac-tivated carbon is an effective adsorbent to remove Bi(Ⅲ) from aqueous solutions with good adsorption capacity.展开更多
L-threonine(L-Thr) obtained by fermentation often contains vestigial hydrosoluble Pb(Ⅱ), Fe(Ⅱ), L-glutamic acid(L-Glu) etc., which affect the product quality. Poly melamine and L-aspartic acid(L-Asp) resin functiona...L-threonine(L-Thr) obtained by fermentation often contains vestigial hydrosoluble Pb(Ⅱ), Fe(Ⅱ), L-glutamic acid(L-Glu) etc., which affect the product quality. Poly melamine and L-aspartic acid(L-Asp) resin functional coconut shell activated carbon composite(PMA/AC) was prepared by a pressure relief-dipping-microwave assisted polymerization method for the simultaneous removals. The adsorption capacities of Pb(Ⅱ), Fe(Ⅱ) and L-Glu could reach to 82.34 mg·g^(-1), 57.82 mg·g^(-1) and 102.58 mg·g^(-1) at conditions of pH 5.0, 45 °C and 4 h with an initial concentration of 0.01 mol·L^(-1), respectively. The present PMA/AC was successfully used to the simultaneous removals of vestigial Pb(Ⅱ), Fe(Ⅱ) and L-Glu from the fermented crude product solution of L-Thr. Moreover, the PMA/AC was carefully characterized by FE-SEM, IR et al. analysis techniques, the results show that abundant PMA particles evenly distributed at the inner and outside surface of AC with a size of(50 ± 20) nm.展开更多
基金Supported by the National Natural Science Foundation of China （No.20176036）.
文摘The enhancement of chemical absorption of CO2 by K2CO3/H2O absorbents in the presence of activated carbon （AC） particles was investigated. The results show that the gas absorption rates can be enhanced significantly in the presence of AC particles, and the maximum enhancement factor 3.7 was observed at low stirring intensities. The enhancement factor increased rapidly with the solid loading during the initial period of absorption and then be- came mild gradually to a maximum value. Both the liquid-solid contact area and the probability of solid particles residing at the gas-liquid interface decreased with the increase of the particle size, leading to a negative effect on the enhancement of mass transfer. The influence of the particles on gas absorption decreased with the reaction rate. The stirring speed changed the interfacial coverage and mass transfer rate on the liquid side and consequently affected the mass transfer between the gas and liquid phases; the enhancement factor decreased with the stirring intensity. A heterogeneous two-zone model was proposed for predicting the enhancement factor and the calculated results agreed well with the experimental data.
文摘The online flow injection preconcentration and electrothermal atomic absorption spectrometry method were used for the determination of trace nickel in electrolytic manganese samples by sorption on a conical minicolumn packed with activated carbon at pH 9.0. The nickel was eluted from the minicolumn with 10%(v/v) nitric acid. An enrichment factor of 190-fold for a sample volume of 10mL was obtained. The detection limit (DL) of nickel with the use of the preconcentration method was 13ng·g -1in the original solid sample. The precision for 10 replicate determinations at 150ng·g -1 nickel concentration was 5.2% relative standard deviation (RSD). The calibration graph was linear with a correlation coefficient of r=0.9996 up to concentration of 660ng·g -1 nickel.
基金funding from Stiftelsen Olle Engkvist Byggmastare(214-0346 and 217-0014)the Swedish Research Council(202103675)。
文摘There has recently been a fundamental need to develop high efficiency microwave absorbers to reduce electro-magnet-ic pollution.It is often very difficult to obtain superior absorption with only one material,so we have explored composites using fillers of activated carbon derived from biological material(oleaster seeds)and resin(apricot tree gum)with Fe_(3)O_(4) in a paraffin wax matrix to improve the dielectric properties and achieve a high specific surface area.A 1 mm thick layer of a Fe_(3)O_(4)+resin(FEOR),with the magnetic nanoparticles anchored to the gum,resulted in a reflection loss of−71.09 dB.We compared this with the results for composites using a filler of Fe_(3)O_(4)+activated carbon,and one with a three-component filler of Fe_(3)O_(4)+activated carbon+resin which had a very porous structure that had a direct effect on the surface polarization.However,the FEOR sample had near-ideal im-pedance matching,close to 1,which resulted in high absorption performance.In addition,the presence of defects improves mi-crowave attenuation by dipole polarization and charge carrier trapping.This work suggests the use of new types of biomaterials to in-crease microwave absorption.
基金Supported by National Natural Science Foundation of China (Grant No.12302177)Guangdong Provincial Basic and Applied Basic Research Foundation of China (Grant No.2024A1515010203)+1 种基金Shenzhen Science and Technology Program of China (Grant No.JCYJ20230807093602005)Shenzhen Key Laboratory of Intelligent Manufacturing for Continuous Carbon Fibre Reinforced Composites of China (Grant No.ZDSYS20220527171404011)。
文摘In order to predict the damage behaviours of 3D-printed continuous carbon fibre(CCF)reinforced composites,when additional short carbon fibre(SCF)composite components are employed for continuous printing or special functionality,a novel path-dependent progressive failure(PDPF)numerical approach is developed.First,a progressive failure model using Hashin failure criteria with continuum damage mechanics to account for the damage initiation and evaluation of 3D-printed CCF reinforced polyamide(PA)composites is developed,based on actual fibre placement trajectories with physical measurements of 3D-printed CCF/PA constituents.Meanwhile,an elastic-plastic model is employed to predict the plastic damage behaviours of SCF/PA parts.Then,the accuracy of the PDPF model was validated so as to study 3D-printed CCF/PA composites with either negative Poisson's ratio or high stiffness.The results demonstrate that the proposed PDPF model can achieve higher prediction accuracies in mechanical properties of these 3D-printed CCF/PA composites.Mechanism analyses show that the stress distribution is generally aggregated in the CCF areas along the fibre placement paths,and the shear damage and matrix tensile/compressive damage are the key damage modes.This study provides a new approach with valuable information for characterising complex 3D-printed continuous fibre-matrix composites with variable mechanical properties and multiple constituents.
文摘A simple and reliable method for the extraction and determination of trace amounts of copper（Ⅱ） ions using activated carbon （AC） impregnated by a new Schiff base 5-[（4-heptyloxyphenyl）azo]-N-（4-propyloxyphenyl）-salicylaldimine （HPPS） and atomic absorption spectrometry is presented. Recovery efficiency and the influence of pH value, volume of sample solution, effect of different eluents, and interfering ions were evaluated. The limit of detection （3σ） was 2.62 ng.mL^-1 and the relative standard deviation （n=10） was 1.5%. Under optimum conditions, the copper ions were concentrated 25 fold using 250 mL of sample solution and 10 mL of eluent. This procedure has been successfully applied to the determination of copper in different water samples.
基金Project(2007AA06Z121) supported by the National High Technology Research and Development Program of ChinaProject(50774095) supported by the National Natural Science Foundation of ChinaProject(CL12111) supported by the Undergraduate Innovation Experimentation Plan of Central South University,China
文摘Coconut-based activated carbons were modified with sodium dodecyl sulfate (SDS). The activated carbons, which were modified by different concentrations of SDS, were characterized by acid/base titrations, textural analysis (BET), atomic absorption spectrochemical analysis and Zeta potential measurements. The effects of SDS modification on Pb2+ absorption were studied further. The results indicate that after the modification of SDS, there are new functional groups on the surface of modified activated carbons and the number of functional group has changed remarkably, the total acidity decreases observably, but the total alkalinity increases dramatically. With the increase of surface load with SDS, the Pb2+ adsorption mass of activated carbons increases and the optimal pH for Pb2+ adsorption of the SDS modified activated carbons is 5. The experimental data are simulated better by Freundlich isotherm model for the modified activated carbons, and the experimental data are simulated better by Langmuir isotherm model for unmodified ones.
文摘In present study,we report the preparation of coconut shell activated carbon as adsorbent and its appli-cation for Bi(Ⅲ) removal from aqueous solutions.The developed adsorbent was characterized with scanning elec-tron microscope(SEM),Fourier Transform Infrared(FTIR),C,H,N,S analyzer,and BET surface area analyzer.The parameters examined include agitation time,initial concentration of Bi(Ⅲ),adsorbent dose and temperature.The maximum adsorption of Bi(Ⅲ)(98.72%) was observed at 250 mg·L-1 of Bi(Ⅲ) and adsorbent dose of 0.7 g when agitation was at 160 r·min-1 for 240 min at(299±2) K.The thermodynamic parameters such as Gibb's free energy(△Gθ),enthalpy(△Hθ) and entropy(△Sθ) were evaluated.For the isotherm models applied to adsorption study,the Langmuir isotherm model fits better than the Freundlich isotherm.The maximum adsorption capacity from the Langmuir isotherm was 54.35 mg?g?1 of Bi(Ⅲ).The kinetic study of the adsorption shows that the pseudo second order model is more appropriate than the pseudo first order model.The result shows that,coconut shell ac-tivated carbon is an effective adsorbent to remove Bi(Ⅲ) from aqueous solutions with good adsorption capacity.
基金Supported by the National Natural Science Foundation of China(U1407110)2014 Special Funds of Guangdong Province for Collaborative Innovation and Environment Platform Construction,Public Research and Capacity Building(2014B090901010)
文摘L-threonine(L-Thr) obtained by fermentation often contains vestigial hydrosoluble Pb(Ⅱ), Fe(Ⅱ), L-glutamic acid(L-Glu) etc., which affect the product quality. Poly melamine and L-aspartic acid(L-Asp) resin functional coconut shell activated carbon composite(PMA/AC) was prepared by a pressure relief-dipping-microwave assisted polymerization method for the simultaneous removals. The adsorption capacities of Pb(Ⅱ), Fe(Ⅱ) and L-Glu could reach to 82.34 mg·g^(-1), 57.82 mg·g^(-1) and 102.58 mg·g^(-1) at conditions of pH 5.0, 45 °C and 4 h with an initial concentration of 0.01 mol·L^(-1), respectively. The present PMA/AC was successfully used to the simultaneous removals of vestigial Pb(Ⅱ), Fe(Ⅱ) and L-Glu from the fermented crude product solution of L-Thr. Moreover, the PMA/AC was carefully characterized by FE-SEM, IR et al. analysis techniques, the results show that abundant PMA particles evenly distributed at the inner and outside surface of AC with a size of(50 ± 20) nm.
