NEW MODEL OF GAS FLOW PROBLEM IN MULTI-LAYERED GAS RESERVOIR AND APPLICATION

In this paper, the new model of the real gas filtration problem has been presented multi-layered gas reservoir, when a gas well output and wellbore storage may be variable, and have obtained the exact solutions of pressure distribution for each reservoir bed under three kinds of typical out-boundary conditions. As a special case, according to the new model have also obtained the qxact solutions of presssure distribution in homogeneous reservoir and is given important application in gas reservoir development.

Changes in filtration and capacitance properties of highly porous reservoir in underground gas storage:CT-based and geomechanical modeling

The paper presents the results of comprehensive studies of filtration and capacitance properties of highly porous reservoir rocks of the aquifer of an underground gas storage facility.The geomechanical part of the research included studying the dependence of rock permeability on the stress-strain state in the vicinity of the wells,and physical modeling of the implementation of the method of increasing the permeability of the wellbore zone-the method of directional unloading of the reservoir.The digital part of the research included computed tomography(CT)-based computer analysis of the internal structure,pore space characteristics,and filtration properties before and after the tests.According to the results of physical modeling of deformation and filtration processes,it is found that the permeability of rocks before fracture depends on the stress-strain state insignificantly,and this influence is reversible.However,when downhole pressure reaches 7-8 MPa,macrocracks in the rock begin to grow,accompanied by irreversible permeability increase.Porosity,geodesic tortuosity and permeability values were obtained based on digital studies and numerical modeling.A weak degree of transversal anisotropy of the filtration properties of rocks was detected.Based on the analysis of pore size distribution,pressure field and flow velocities,high homogeneity and connectivity of the rock pore space is shown.The absence of pronounced changes in pore space characteristics and pore permeability after non-uniform triaxial loading rocks was shown.On the basis of geometrical analysis of pore space,the reasons for weak permeability anisotropy were identified.The filtration-capacitance properties obtained from the digital analysis showed very good agreement with the results of field and laboratory measurements.The physical modeling has confirmed the efficiency of application of the directional unloading method for the reservoir under study.The necessary parameters of its application were calculated:bottomhole geometry,stage of operation,stresses and pressure drawdown value.

Progression of injectivity damage with oily waste water in linear flow

Numerous laboratory experiments and field cases show that even very small amount of oil in injected water can cause severe injectivity damage. Although injectivity decline caused by oil droplets has been studied experimentally, there is still lack of an easy-to-use and widely accepted model to predict the decline behavior. In this work, we developed an analytical model to predict the time-dependent progress of the water permeability reduction in linear flow by analyzing experimental data obtained from linear core flooding. The model considers mass transfer of the oil phase from the produced water to the rock due capture effects by dispersion, advection and adsorption inside the rock. As the captured oil saturation increases, permeability reduces following the relative permeability drainage relationship. The reduction stabilizes when the oil saturation comes to an equilibrium value controlled by oil droplet size and injection velocity. The model is calibrated using published experimental data from prolonged core floods with oil- contaminated waste water. Theoretical runs of the model replicate all the effects known from experimental observations. Resulting from the model is a distributed change of permeability vs. time and distance from the point of injection that can be converted to the overall injectivity damage.

Modeling of strain and filtration properties of a semi-finished leather product

A study on deformation and filtration properties of a leather semi-finished product after chrome tanning are presented.The analytical dependences of compressive load on compressive(recovery)strain and moisture content of a leather semi-finished product are obtained.The empirical dependences of hydraulic gradient on filtration rates are determined for various compression ratios of the leather semi-finished product.It was revealed that with an increase in compressive load and moisture content of the leather semi-finished product,the compressive deformation increases.The shoulder section is subject to the greatest deformation,then the belly section and the least deformation is observed in the butt section.A linear relationship has been established between the hydraulic gradient and the rate of moisture filtration through the leather semi-finished product in the directions perpendicular and parallel to its surface.