Efficient placement technology of proppants based on structural stabilizers

Fiber is highly escapable in conventional slickwater,making it difficult to form fiber-proppant agglomerate with proppant and exhibit limited effectiveness.To solve these problems,a novel structure stabilizer(SS)is developed.Through microscopic structural observations and performance evaluations in indoor experiments,the mechanism of proppant placement under the action of the SS and the effects of the SS on proppant placement dimensions and fracture conductivity were elucidated.The SS facilitates the formation of robust fiber-proppant agglomerates by polymer,fiber,and quartz sand.Compared to bare proppants,these agglomerates exhibit reduced density,increased volume,and enlarged contact area with the fluid during settlement,leading to heightened buoyancy and drag forces,ultimately resulting in slower settling velocities and enhanced transportability into deeper regions of the fracture.Co-injecting the fiber and the SS alongside the proppant into the reservoir effectively reduces the fiber escape rate,increases the proppant volume in the slickwater,and boosts the proppant placement height,conveyance distance and fracture conductivity,while also decreasing the proppant backflow.Experimental results indicate an optimal SS mass fraction of 0.3%.The application of this SS in over 80 wells targeting tight gas,shale oil,and shale gas reservoirs has substantiated its strong adaptability and general suitability for meeting the production enhancement,cost reduction,and sand control requirements of such wells.

Study on Compound Stabilizer Formulation for Mango Juice with Skin

[Objectives]The effects of stabilizers such as sodium carboxymethyl cellulose,pectin,sodium alginate and xanthan gum on the stability of mango juice with skin were discussed using mango as the raw material.[Methods]The formula and stability of mango beverage with skin were studied using mango juice with skin as the raw material.Four stabilizers,including pectin,sodium alginate and sodium carboxymethyl cellulose,were added to improve the stability of the juice.Based on single factor experiments and a response surface experiment,the stability model of mango juice was established to determine the best compound stabilizer.[Results]According to an orthogonal experiment on the stability of mango juice with skin,the optimum technical parameters were as follows:sodium carboxymethyl cellulose 0.20%,xanthan gum 0.08%,sodium alginate 0.18%,and pectin 0.14%,with which the optimal suspension stability was 69.12%.The optimum technical parameters from the response surface experiment were as follows:sodium carboxymethyl cellulose 0.199%,pectin 0.1185%,sodium alginate 0.163%,and xanthan gum 0.077%,with which the suspension stability was 70.32%.It was found that the stability of mango juice with skin obtained by the response surface experiment was better than that by the orthogonal experiment,and the order of factors affecting the stability of mango was sodium alginate(C)>sodium carboxymethyl cellulose(A)>pectin(D)>xanthan gum(B).[Conclusions]The formula of compound stabilizer for mango juice was optimized by the orthogonal experiment and the response surface method,providing a theoretical basis for the actual production of mango juice with skin.

A high entropy stabilized perovskite oxide La_(0.2)Pr_(0.2)Sm_(0.2)Gd_(0.2)Sr_(0.2)Co_(0.8)Fe_(0.2)O_(3−δ)as a promising air electrode for reversible solid oxide cells

Reversible solid oxide cell(RSOC)is a new energy conversion device with significant applications,especially for power grid peaking shaving.However,the reversible conversion process of power generation/energy storage poses challenges for the performance and stability of air electrodes.In this work,a novel high-entropy perovskite oxide La_(0.2)Pr_(0.2)Gd_(0.2)Sm_(0.2)Sr_(0.2)Co_(0.8)Fe_(0.2)O_(3−δ)(HE-LSCF)is proposed and investigated as an air electrode in RSOC.The electrochemical behavior of HE-LSCF was studied as an air electrode in both fuel cell and electrolysis modes.The polarization impedance(Rp)of the HE-LSCF electrode is only 0.25Ω·cm^(2) at 800℃ in an air atmosphere.Notably,at an electrolytic voltage of 2 V and a temperature of 800℃,the current density reaches up to 1.68 A/cm^(2).The HE-LSCF air electrode exhibited excellent reversibility and stability,and its electrochemical performance remains stable after 100 h of reversible operation.With these advantages,HE-LSCF is shown to be an excellent air electrode for RSOC.

Effect of external and internal cues on core muscle activation during the Sahrmann five-level core stability test

BACKGROUND Pain in the back or pelvis or fear of back pain may affect the timing or cocontraction of the core muscles.In both static and dynamic movements,the Sahrmann core stability test provides an assessment of core muscle activation and a person's ability to stabilize the lumbopelvic complex.Preparatory cues and images can be used to increase the activation of these muscles.To attain optimal movement patterns,it will be necessary to determine what cueing will give the most effective results for core stability.AIM To investigate the effects of external and internal cues on core muscle activation during the Sahrmann five-level core stability test.METHODS Total 68 participants(21.83±3.47 years)were randomly allocated to an external(n=35)or internal cue group(n=33).Participants performed the Sahrmann fivelevel core stability test without a cue as baseline and the five-level stability exercises with an internal or external cue.External cue group received a pressure biofeedback unit(PBU),and the internal cue group received an audio cue.A Delsys Trigno^(TM)surface electromyography unit was used for muscle activation from the rectus abdominis,external oblique,and transverse abdominis/internal oblique muscles.RESULTS Linear mixed effects model analysis showed that cueing had a significant effect on core muscle activation(P=0.001);however,there was no significant difference between cue types(internal or external)(P=0.130).CONCLUSION Both external and internal cueing have significant effects on core muscle activation during the Sahrmann five-level core stability test and the PBU does not create higher muscle activation than internal cueing.

Recent progress on stability and applications of flexible perovskite photodetectors

Flexible photodetectors have garnered significant attention by virtue of their potential applications in environmental monitoring,wearable healthcare,imaging sensing,and portable optical communications.Perovskites stand out as particularly promising materials for photodetectors,offering exceptional optoelectronic properties,tunable band gaps,low-temperature solution processing,and notable mechanical flexibility.In this review,we explore the latest progress in flexible perovskite photodetectors,emphasizing the strategies developed for photoactive materials and device structures to enhance optoelectronic performance and stability.Additionally,we discuss typical applications of these devices and offer insights into future directions and potential applications.

Synergistic effect of nitrocellulose coating on structural and reactivity stabilization of ammonium nitrate oxidizer

The present work aims to stabilize the room temperature allotropic transition of ammonium nitrate(AN)particles utilizing a microencapsulation technique,which involves solvent/non-solvent in which nitrocellulose(NC)has been employed as a coating agent.The SEM micrographs revealed distinct features of both pure AN and NC,contrasting with the irregular granular surface topography of the coated AN particles,demonstrating the adherence of NC on the AN surface.Structural analysis via infrared spectroscopy(IR)demonstrated a successful association of AN and NC,with slight shifts observed in IR bands indicating interfacial interactions.Powder X-ray Diffraction(PXRD)analysis further elucidated the structural changes induced by the coating process,revealing that the NC coating altered the crystallization pattern of its pure form.Thermal analysis demonstrates distinct profiles for pure and coated AN,for which the coated sample exhibits a temperature increase and an enthalpy decrease of the room temperature allotropic transition by 6℃,and 36%,respectively.Furthermore,the presence of NC coating alters the intermolecular forces within the composite system,leading to a reduction in melting enthalpy of coated AN by~39%compared to pure AN.The thermal decomposition analysis shows a two-step thermolysis process for coated AN,with a significant increase in the released heat by about 78%accompanied by an increase in the activation barrier of NC and AN thermolysis,demonstrating a stabilized reactivity of the AN-NC particles.These findings highlight the synergistic effect of NC coating on AN particles,which contributed to a structural and reactive stabilization of both AN and NC,proving the potential application of NC-coated AN as a strategically advantageous oxidizer in composite solid propellant formulations.

Assessment of Cement-Lime as Stabilizer on Mud Bricks

The aim of this study was to evaluate the compressive strength of clay bricks and their stability to water absorption by inserting stabilizers such as lime and cement of 0%, 4%, 6%, 8%, 10%, 12% to 14%. Spectrometric analysis was used to characterize the various stabilizers and the clay used, and tests of resistance and water absorption were also carried out. The clay was found to be an aluminosilicate (15.55% to 17.17% Al2O3 and 42.12% to 44.15% SiO2). The lime contains 90.84% CaO and the cement has 17.80% SiO2, 3.46% Al2O3, 2.43% Fe2O3 and 58.47% CaO in the combined form of tricalcium silicate, dicalcium silicate, tricalcium aluminate and ferro-tetra calcium aluminate. The results showed that the insertion of locally available stabilizers (lime and cement) improved the strength of the material by almost 80% when the lime was increased from 0% to 14% for 14 days. For compressed cement, a 65% increase in strength was observed under the same conditions. Strength increases with drying time, with a 52% increase in strength at 28 days compared to 14 days. Furthermore, compressed cement bricks have a more compact structure, absorbing very little water (32%). In view of all these results, cement appears to be the best stabilizer, and compression improves compressive strength and reduces water absorption.

Effects of spatial heterogeneity on pseudo-static stability of coal mine overburden dump slope,using random limit equilibrium and random finite element methods:A comparative study

Sudden and unforeseen seismic failures of coal mine overburden(OB)dump slopes interrupt mining operations,cause loss of lives and delay the production of coal.Consideration of the spatial heterogeneity of OB dump materials is imperative for an adequate evaluation of the seismic stability of OB dump slopes.In this study,pseudo-static seismic stability analyses are carried out for an OB dump slope by considering the material parameters obtained from an insitu field investigation.Spatial heterogeneity is simulated through use of the random finite element method(RFEM)and the random limit equilibrium method(RLEM)and a comparative study is presented.Combinations of horizontal and vertical spatial correlation lengths were considered for simulating isotropic and anisotropic random fields within the OB dump slope.Seismic performances of the slope have been reported through the probability of failure and reliability index.It was observed that the RLEM approach overestimates failure probability(P_(f))by considering seismic stability with spatial heterogeneity.The P_(f)was observed to increase with an increase in the coefficient of variation of friction angle of the dump materials.Further,it was inferred that the RLEM approach may not be adequately applicable for assessing the seismic stability of an OB dump slope for a horizontal seismic coefficient that is more than or equal to 0.1.

Development of a Thermal Fogger-specific Sedimentation Stabilizer

In order to solve the drifting away of thermal fog droplets during thermal spraying and the incompatibility between fog droplet carrier and conventional com- mercial agro-chemicals, the fog droplet carrier, surfactant, condensation nucleus ma- terial and antifreeze, dispersant, thickener and defoamer were screened and assem- bled to develop a thermal fog sedimentation stabilizer in this study, thereby provid- ing technical support for application and promotion of thermal spraying technology in pest and disease control in crops.

通过稳定子(Stabilizer)的单项特征标

假设G为有限群,N为G的正规子群,χ∈Irr(G),θ∈Irr(Nχ_N),则由Clifford定理存在唯一的χ_0∈Irr(G_0).使得χ=(χ_0)~G.而(χ_0)_N=e·θ,此处e为正整数。G_θ={g∈G|θ~=θ}为G作用在θ上的稳定子。若χ是单项时,则χ_θ可能不是单项的。本文运用[4]的方法,用正规子群N的内部结构,给出χ_0是单项的充分条件。主要结果:当N是超可解时,χ_0是单项的。当N存在正规的Sylow p-子群时,且θ是p-特征标时,χ_0是单项的。

Principle and Method of Optimization Design for Soft Soil Stabilizer

A stabilized soil structure formation model was introduced. In order to form compact stabilized soil structure, cementitious hydrates were needed to wrap and bind the soil aggregates. Meanwhile, expansible hydrates were needed to squeeze and fill the pores, especially the pores in the aggregates. The experimental results show that the influences of various chemical characteristic factors of soil on the strength of the stabilized soil are boiled down, for the influence on the concentration of Ca（OH）2 in the pore solution of the stabilized soil, and the amount of CSH generated by cement. Finally an optimization design method is proposed, with which the stabilizer can be designed according to characteristics of soil samples.

Modification and investigation of silica particles as a foam stabilizer

As a solid foam stabilizer, spherical silica particles with diameters ranging from 150 to 190 nm were prepared via an improved Stober methOd and were subsequently modified using three different silane coupling agents to attain the optimum surface hydrophobicity of the particles. Fourier transform infrared （FTIR） spectra and the measured contact angles were used to characterize the surface properties of the prepared particles. The foam stability was investigated by the foam drainage half-life and the expansion viscoelastic modulus of the liquid film. The results demonstrate that all of the modified silica nanoparticles effectively improve the foam stability. The surface hydrophobicity of the modified particles is found to be a key factor influencing the foam stability. The optimum contact angle of the particles lies in the ap- proximate range from 50° to 55°. The modifier molecular structure used can also influence the stabilizing foam property of the solid particles The foam system stabilized by （CH3）2SiCl2-modified silica particles exhibits the highest stability; its drainage half-life at maximum increases by 27% compared to that of the blank foam system and is substantially greater than those of the foam systems stabilized by KH570- and KH550-modified particles.

Improved dissolution and oral absorption by co-grinding active drug probucol and ternary stabilizers mixtures with planetary beads-milling method

The objective of this work is to construct a nanosuspension drug delivery system of probucol,a BCS II drug,in order to improve its dissolution and oral bioavailability.The wet milling procedure using planetary beads-milling equipment was utilized to grind the raw probucol to ultrafine nanoparticle/nanocrystal aqueous suspension that was further solidified by freeze-drying process.Cellulose derivatives of different substitution groups and molecular weights,including HPMC,HPC,and MC,were evaluated as the primary stabilizer of probucol nanosuspension.Ternary stabilizers system composed of a primary stabilizer(cellulose derivative,i.e.HPC),a nonionic surfactant(Pluronic R F68),and an anionic surfactant(SDS)was employed to obtain probucol nanosuspension of finer particle size and enhanced dissolution in aqueous media.The probucol nanosuspension with good physical stability showed no obvious change of particle size even after storing over 7 d at 4°C or 25°C.The solidified probucol nanosuspension with trehalose as the cryoprotectant showed the highest dissolution rate(>60%at 2 h)compared to other cryoprotectant.The in vivo pharmacokinetic evaluation indicated about 15-folds higher AUC value of the probucol nanosuspension compared to that of coarse probucol suspension after oral administration to rats.The probucol nanosuspension prepared by wet-milling and ternary stabilizers system may find wide applications for improving the dissolution and oral absorption of water-insoluble drugs.

Rare Earth Stearates as Thermal Stabilizers for Rigid Poly(vinyl chloride)

A series of stearates with different rare-earth ion were investigated as thermal stabilizers for rigid PVC at 180 ℃ in air. Their stabilizing efficiency was based on measuring the rate of dehydrochlorination. The resulted revealed the higher stabilizing efficiency of the investigated rare-earth stearates as thermal stabilizers for rigid PVC compared with the thermal stabilizers for industry: calcium stearate, zinc stearate, butyl stannum mercaptide, phosphite esters, β-diketone and epoxidized sunflower oil. This was well illustrated by longer incubation period (T_S) values and lower rate of dehydrochlorination. The stable efficiency was affected by the nature of rare-earth element's individual electronic shell. The mechanism for the stabilizing effect of rare-earth stearates was proposed. The result was experimentally proved based on IR spectrum.

SYNTHESIS AND CHARACTERIZATION OF NEW STABILIZERS WITH OPTIMAL MOLECULAR WEIGHT

Over 2 x 10(8) tons of polymers are produced every year, and a large portion of polymers faces the degradation problem. There are many effective methods to protect polymers against degradation and the addition of stabilizers to polymer remains the most convenient and effective way of enhancing polymer life and performance. In this article, a series of effective stabilizers with optimal molecular weight (MW), including common, monomeric and polymeric stabilizers (antioxidant and light stabilizer) were synthesized using isocyanation, controlled isocyanation, hydrosilylation, epoxide addition, macroreaction of stabilizing functional compounds and polymerization of monomeric stabilizers. The structure and performance of these new stabilizers were characterized by using IR, NMR, MS, UV-spectra, XPS and elemental analysis. The current development of stabilizer synthesis was also reviewed.

Study on Mechanism of Rare Earth PVC Stabilizer

Rare earth compounds can be used as PVC thermal stabilizers. According to the infrared spectra of the mixture of PVC and some stearates, the mechanism of stabilization of different stearates was studied. The specialty of rare earth stabilizers was found. They can change the conformation of PVC and restrain the elimination of HCl. From this aspect, the unique synergetic effect with other stabilizers of rare earth compounds can be explained.

Application of New-type Soil Stabilizer Q2 in Subgrade Construction

The research analyzed characters of soil stabilizer and detailed the solidification mechanism.Furthermore,new type soil stabilizer Q2 was used in a base of Beijing Vocational College of Agriculture and a solidified road with length of 250 m,width of 4 m and thickness of 0.25 m were constructed.The road was tested with an agricultural truck and subgrade tolerance to freezing was tested also.It is suggested that new type soil stabilizer would reduce construction cost of road,protect environment,and reduce construction period,with high value of application.

Mechanical Behaviors of ZrO_2-Al_2O_3 Ceramic Composites with Y_2O_3 as Stabilizer

The ZrO2-Al2O3 ceramic composites were prepared by appropriate techniques with commercial ZrO2 and Al2O3 powders as raw materials and Y2O3 as stabilizer. The results indicate that with the introduction of Al2O3 into the ZrO2 matrix where the quantity of additive Y2O3 is 3.5% (mole fraction), the growth of ZrO2 grains is efficiently inhibited, which helps the ZrO2 grains exist in a metastable tetragonal manner; thus higher strength and toughness are acquired. When the content of alumina is 20% (mass fraction), the bending strength and fracture toughness of the composites are 676.7 MPa and 10 MPa·m1/2 respectively, the mechanical behaviors are close to those prepared with ZrO2 and Al2O3 powders synthesized through wet chemical approach. The mechanical behaviors of the composites are well improved owing to the dispersion toughening of alumina grains and phase transformation toughening of zirconia grains.

Power system stabilizer design using hybrid multi-objective particle swarm optimization with chaos

A novel technique for the optimal tuning of power system stabilizer (PSS) was proposed,by integrating the modified particle swarm optimization (MPSO) with the chaos (MPSOC).Firstly,a modification in the particle swarm optimization (PSO) was made by introducing passive congregation (PC).It helps each swarm member in receiving a multitude of information from other members and thus decreases the possibility of a failed attempt at detection or a meaningless search.Secondly,the MPSO and chaos were hybridized (MPSOC) to improve the global searching capability and prevent the premature convergence due to local minima.The robustness of the proposed PSS tuning technique was verified on a multi-machine power system under different operating conditions.The performance of the proposed MPSOC was compared to the MPSO,PSO and GA through eigenvalue analysis,nonlinear time-domain simulation and statistical tests.Eigenvalue analysis shows acceptable damping of the low-frequency modes and time domain simulations also show that the oscillations of synchronous machines can be rapidly damped for power systems with the proposed PSSs.The results show that the presented algorithm has a faster convergence rate with higher degree of accuracy than the GA,PSO and MPSO.

Global stabilizer of a general class of feedback nonlinear systems and its exponential convergence

We discuss the global stabilization procedure which renders a general class of feedback nonlinear systems exponential convergent, Our stabilizer consists of a nested saturation function, which is a nonlinear combination of saturation functions. Here we prove the exponential convergence of the stabilizer for the first time and give numerical examples to illustrate the efficiency of the result given above,