Evaluation of VSK separation in the classification of two mineralogically different iron ore fines

With gradually diminishing Fe grade in tandem with the ever-increasing demand for high-grade iron ores,iron ore industries are now focusing on the beneficiation of low-grade iron ore fines,mainly considered waste.Besides,the scarcity of water at many of the mines’sites and the new water conservation policies of the governments have necessitated research on suitable dry beneficiation routes.In this context,an effort has been made to evaluate the efficacy of a dry classification unit,such as the VSK separator,in upgrading the iron values of two low-grade Indian iron ore fines,named Sample 1 and Sample 2.The mineralogical studies,involving scanning electron microscopy and X-ray diffraction,suggest that Sample 1 is a low-grade blue dust sample(51.2wt%Fe)containing hematite and quartz as the major minerals,while Sample 2(53.3wt%Fe)shows the presence of goethite in addition to hematite and quartz.The experiments,carried out using Box-Benkhen statistical design,indicate that blower speed,followed by feed rate,is the most influencing operating parameter in obtaining a good product in the VSK separator.At optimum levels of the operating factors,a fines product with~55wt%Fe at a yield of~40%can be obtained from Sample 1,while Sample 2 can be upgraded to~56wt%Fe at a yield of~85%.The results suggest that the VSK separator can be employed as an efficient intermediate unit operation in a processing circuit to upgrade the iron contents of iron ore fines.

The process analysis of fine iron ore reduced in fluidized bed

The processes of fine iron ore reduced in fluidized bed have been reviewed in this paper,the superiorities and limitations of the processes of direct reduction,pre-reduction in fluidized bed have also been comprehensively analysed,which matches with bath smelting furnace or coke bed type furnace.The analysis has also been made on several controversial topics,and the gas use ratio has been point out to be the key of the competition of the reduction process in fluidized bed.The suitability with final reduction furnace is also important to the energy saving in the whole smelting reduction process.

Dissolution kinetics of aluminum and iron from coal mining waste by hydrochloric acid

The extrartion of aluminum from coal mining waste(CMW) is an important industrial process.The two major problems in applications are low aluminum dissolution efficiency and high iron content in the raw material,which affect the quantity and quality of products.To improve the aluminum recovery process,the leaching kinetics of CMW with hydrochloric acid was studied.A shrinking core model was used to investigate aluminum and iron dissolution kinetics.Based on the kinetic characteristics,a process for recovering aluminum was proposed and tested experimentally.It is found that the aluminum leaching reaction is controlled by surface reaction at low temperatures(40-80℃) and by diffusion process at higher temperatures(90-106℃).The iron dissolution process is dominated by surface reaction at 40-100℃.The results show that iron could be dissolved or separated by concentrated hydrochloric acid.Fine grinding will improve aluminum dissolution significantly.

The Effect of Gelatin on the Preparation of Silica Coated Iron Particles

A method is described for coating fine iron particles(~1 μm) with a uniform silica layer, produced by the hydrolysis of tetraethyl orthosilicate. The presence of a small amount of gelatin on the surface of the iron particles facilitates this process. The X ray photoelectron measurements indicated that the gelatin interacted with the surface of the iron particles by means of both nitrogen(in —NH 2 groups) and oxygen(in —COOH groups) and then bound to the silica. The silica coating increases the resistance of the iron particles to oxidation on heating in air, which makes the temperature at which an observable oxidization occurs from 330 ℃ to 400 ℃ raised.

Intensifying Gaseous Reduction of High Phosphorus Iron Ore Fines by Microwave Pretreatment

Gaseous reduction kinetics of the high phosphorus iron ore fines from Hubei in China and effect of microwave pretreatment on the gaseous reduction behavior were studied. Gaseous reduction kinetics were investigated by TG （Thermogravimetric） methods using LINSEIS STA PT 1600 thermal analysis equipment. Microwave pretreatments to the ore fines with four power levels were performed using a high temperature microwave reactor. Its effect was examined by TG methods and its mechanism was analyzed by SEM （scanning electron microscope） and EDS （energy dispersive spectrometer）. Gaseous reduction tests were carried out using a tubular furnace. Results of kinetic study indicate that controlling step of the gaseous reduction of the ore fines is a mixing control of gas internal diffusion and interface chemical reaction when reduction fraction is less than 0.8 and is solid state diffusion when reduction fraction is more than 0.8. Microwave pretreatment of the ore fines could change the pore structure of the oolitic unit to generate cracks, fissures and loose zones, which promotes reduction in the early stage and delays the occurrence of sintering. Gaseous reduction tests show in the condition that the ore fines are pretreated with a microwave power of 450 W for 4 min and reduced under temperature of 1 273 K, the gaseous reduction of the ore fines could be apparently intensified. Using CO or H2 as a reductant and ore fines being reduced for 1.5 to 2 h , increase of metallization rate of the ore fines is 10% to 13%.

Slag/metal Separation Process of Gas-reduced Oolitic High-phosphorus Iron Ore Fines

Slag/metal separation process of the highly reduced oolitic high-phosphorus iron ore fines was investigated. Samples were prepared using the reduced ore fines （metallization rate： 88%） and powder additives of CaO and Na2CO3. Slag/metal separation behavior tests were conducted using a quenching method and the obtained metal parts were subjected to direct observation as well as microstructure examination with SEM and EDS; iron recovery and phosphorus distribution tests were conducted using a Si-Mo high temperature furnace and the obtained metal parts were examined by ICP-AES analysis and mass measurement. Thermodynamic calculation using coexistence theory of slag structure was also performed. Results show that temperature for slag/metal separation must be higher than 1823 K and a satisfying slag/metal separation of the highly reduced ore fines needs at least 4 min; phosphorus con- tent of hot metal is mainly determined by thermodynamics; temperature of 1823-1873 K and Na2CO3 mixing ratio of about 3 % are adequate for controlling phosphorus content to be less than 0.3 mass% in hot metal; temperature, time and Na2CO3 mixing ratio do not have significant effect on iron recovery, and iron recovery rate could be higher than 80% as long as a good slag/metal separation result is obtained.

Effects of pressure and plastic addition on sticking of fine iron ore particles in fluidized bed reduction

The adhesion of fine iron ore particles during fluidized bed reduction was studied using pressurized visible fluidized bed laboratory equipment.The results showed that the optimal operating parameters for pure hydrogen reduction under high pressure were reduction temperature of 1073 K,particle size of 0.18-0.66 mm,pure H_(2) linear velocity of 0.8 m/s,reduction pressure of 200 kPa,and reduction time of 50 min.When plastic particles were mixed into the fluidized bed,the optimal parameters were reduction temperature of 973 K,particle size of 0.18-0.66 mm,pure H_(2) linear velocity of 0.8 m/s,reduction pressure of 100 kPa,mass content of plastic particles of 8%,and reduction time of 65 min.The chemical reaction resistance is much higher than the inner diffusion resistance at the initial stage of the reaction,whereas,in later stage,the inner diffusion resistance exceeds the chemical reaction resistance.The contact area of iron atoms or iron whiskers gradually decreases with the increase in reduction pressure from 0.20 to 0.45 MPa,and the sticking trend gradually decreases.Adding plastic particles in the fluidized reduction process of fine iron ore can effectively inhibit the adhesion among fine iron ore particles.

Reduction Kinetics of Fine Iron Ore Powder in Mixtures of H_2-N_2 and H_2-H_2O-N_2 of Fluidized Bed

Reduction kinetics of fine iron ore powder in different gas mixtures were investigated in high-temperature fluidized bed at a scale of kilograms. Influence of processing parameters, such as particle size, gas flow velocity, height of charge, temperature, compositions of gas mixture, and percentage of inert components, on reduction ki- netics was experimentally determined under the condition of fluidization. The equations for calculating instantaneous and average oxidation rates were deduced. It was found that an increasing H2 O percentage in the gas mixture could obviously decrease the reduction rate because the equilibrium partial pressure of H2 decreased with increasing content of Hz O in the gas mixture and then the driving force of reduction reaction was reduced. When the H2 content was high, .the apparent reaction rate was so rapid when the average size of iron ore fines was less than 1 mm that the re- action temperature can be as low as 750 ℃ ; when the average size of iron ore fines was more than 1 mm, a high re- action temperature of 800 ℃ was required. In addition, it was also found that the content of H2O should be less than 10% for efficient reduction.

Recent status of fluidized bed technologies for producing iron input materials for steelmaking

Today steel is produced by two steelmaking processes, the basic oxygen furnace and the electric arc furnace, Three types of iron input materials for both processes are liquid hot metal or in solidified form as pig iron, direct reduced iron （DRI） and hot briquetted iron （HB1） as well as steel scrap. Hot metal, pig iron, DRI and HBI are virgin iron materials, which have to be produced from iron ore by the so-called ironmaking technologies. New ironmaking processes based on fluidized bed technology have been developed in the last two decades. The main advantage of these technologies is that fine ore can be directly used in the processes and prior treatment such as sintering or pelletizing can be avoided which is required for the established processes. Theoretical aspects for reduction of fine iron oxides in a fluidized bed reactor system will be explained. The fluidized bed reducing technologies utilized in the most advanced new ironmaking processes for direct use of fine ore, FINMET, Circored, FINEX~ and Hismelt will be compared.

Preparation of blast furnace burdens by composite agglomeration process: effect of distribution of magnetite and hematite concentrates in pelletized and matrix feed

Effect of distribution of iron concentrates between pelletized and matrix feed on the preparation of blast furnace burdens from two different kinds of fine iron concentrates (magnetite and hematite) by composite agglomeration process (CAP) was explored. It was found that when the mass ratio of iron concentrate A (magnetite) to iron concentrate B (hematite) in the mixed feed was constant, the proportion of iron concentrate A in the pelletized and matrix feed significantly affected the quality of CAP products. Particularly, as the proportion of iron concentrate A in the pelletized feed increased from 0 to 100%, the yield decreased from 82.11% to 79.19% and the tumbler index decreased from 71.33% to 68.27%. The mineralization characterization results indicated that when 100% iron concentrate A was used as the pelletized feed, the crystallization styles of the outer layer and the inner layer of the pellet were different, and a lot of pores exist around hematite and magnetite phases in the pelletized part, with the weak connection of pelletized and matrix part, resulting in poor strength of agglomeration product.

Influence of Coating MgO on Sticking and Functional Mechanism during Fluidized Bed Reduction of Vanadium Titano-magnetite

The vanadium titano-magnetite （VTM） iron ore fines of 110--150/xm in diameter were reduced in a trans- parent quartz fluidized bed by 70 %CO-30 % H2 （volume fraction） mixtures. MgO powders served as coating agent to solve sticking problem. Two coating methods were introduced in this experiment： high temperature injection method and briquetting→oxidizing roast→crushing method. According to the experimental results, the minimum effective coating amount of MgO was 0. 1 mass%. The metallization ratio （MR） of the product rose from around 58% to above 90% with the above treatments. To investigate the sticking mechanism of fine ore, the morphology evolution was in- vestigated. Instead of iron whiskers, an interlaced fibrous porous surface formed. The ulvospinel （2FeO ： TiO2 ） in VTM is more difficult to be reduced than FeO according to thermodynamic calculation. XRD results showed that MgO diffused into Fe203 lattice before forming pleonaste （MgO · Fe2O3 ） during oxidizing roast at 1273 K. The melting point of the pleonaste is 1986 K and that made contribution to prevent the sticking problem.