The microstructure evolution of the fine-grained 5083 Al alloy was investigated in annealing temperature range of 150−300℃.Then the effects of the different annealed microstructures on high-temperature deformation be...The microstructure evolution of the fine-grained 5083 Al alloy was investigated in annealing temperature range of 150−300℃.Then the effects of the different annealed microstructures on high-temperature deformation behavior were further studied.The results indicate that the initial recrystallization temperature is about 200℃.By tensile tests at 380−570℃and in strain rate range of 4.17×10^(−4)−1.0×10^(−2) s^(−1),the optimum superplastic parameters are obtained as follows:the annealed temperature 250℃,the tensile temperature 550℃and the strain rate 4.17×10^(−4) s^(−1).With the aid of scanning electronic microscopy(SEM),the fractography of the alloy after the superplastic deformation was analyzed.The results reveal that intergranular cavities with fine size and homogeneous distribution are beneficial to superplastic deformation.展开更多
The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 1...The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 10^-4- 1.0× 10^-2 s^-1. The maximum elongation 530% of the fine-grained 5083 AI alloy was obtained at 550℃ and 4.17× 10^-4 s^-1. Fracture analysis by scanning electron microscopy （SEM） indicated that the formation of filament （formed by liquid phase） was greatly affected by the tensile temperature and strain rate. The results also showed that the optimum morphology of formed filament was obtained at 550℃ and a strain rate of 4.17× 10^-4 s^-1. The effect of liquid phase on superplastic deformation of the alloy was further discussed.展开更多
Electrochemical tests were undertaken to determine the optimum conditions in seawater for corrosion protection of friction stir-welded 5083-O Al alloy.Polarization trend observations show that the limiting potential t...Electrochemical tests were undertaken to determine the optimum conditions in seawater for corrosion protection of friction stir-welded 5083-O Al alloy.Polarization trend observations show that the limiting potential that avoids the effects of hydrogen embrittlement is -1.6 V,corresponding to the crossover point between concentration polarization and activation polarization.However,the optimum protection potential is between -1.5 and -0.7 V since the current density at these values is low in the potentiostatic tests.When a galvanic cell is formed in the seawater,the welds exhibit electrochemically stable trends.Welded parts in galvanic tests with various area ratios are stable and have excellent anticorrosion characteristics.展开更多
The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature ra...The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature range of 500-570 ℃ and a strain rate range of 4.17×10^-4 s-1^- 1×10^- 2 s^- 1. Maximum tensile elongation 530% was obtained at 550 ℃ and strain rate ε＆ =4 .17×10^-4 s^-1. Dislocations were observed in grain interiors and at grain boundaries during uniaxial tensile deformation by transmission electronic microscopy （TEM）, respectively. Results show that the grain boundary sliding （GBS） accommodated by dislocation motion is the principal reason for superplastic deformation. The cavities and fracture were observed during uniaxial tensile deformation of the alloy by scanning electronic microscopy （SEM）, indicating that linkage of cavities in large region would induce failure of the material. Moreover, presence of liquid phase at grain boundary also affects the superplastic deformation and behavior of cavities.展开更多
The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average s...The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average size of 15 m and porosity in the range of 0.1 vol. % to 5vol. % . Two distinct TMP procedures are employed to close porosity and refine grain size:extrusion plus rolling and direct rolling. The material processed using the former method exhibits arelatively high superplasticity with a maximum superplastic elongation of 465 % , whereas thatprocessed using the latter method exhibits a maximum superplastic elongation of 295 % . Materialsprocessed using extrusion plus rolling and direct rolling both exhibit similar stress-strainbehavior and strain rate sensitivity factors. The strain rate factors are in the 0.3 to 0.5 range.The difference in their superplastic elongation is possibly the result of differences in grain sizeand available cavity nucleation sites provided by closed gas pores.展开更多
The effect of temperature distribution on warm forming performance was investigated for 5083-O (Al-Mg) sheet metal blanks. Combined isothermal/non-isothermal FEA with design of experiments tools were used to predict a...The effect of temperature distribution on warm forming performance was investigated for 5083-O (Al-Mg) sheet metal blanks. Combined isothermal/non-isothermal FEA with design of experiments tools were used to predict appropriate warm forming temperature conditions for deep drawing and two-dimensional stamping cases. In the investigated temperature range of 25?250 ℃, the formability of Al-5083 alloy is found to be greatly dependent on the temperature distribution of the die and punch. To achieve increased degrees of forming, different temperature levels should be assigned to the corner and body of the die and punch. And the optimal temperature distributions for warm deep drawing and warm two-dimensional stamping are not identical.展开更多
文摘The microstructure evolution of the fine-grained 5083 Al alloy was investigated in annealing temperature range of 150−300℃.Then the effects of the different annealed microstructures on high-temperature deformation behavior were further studied.The results indicate that the initial recrystallization temperature is about 200℃.By tensile tests at 380−570℃and in strain rate range of 4.17×10^(−4)−1.0×10^(−2) s^(−1),the optimum superplastic parameters are obtained as follows:the annealed temperature 250℃,the tensile temperature 550℃and the strain rate 4.17×10^(−4) s^(−1).With the aid of scanning electronic microscopy(SEM),the fractography of the alloy after the superplastic deformation was analyzed.The results reveal that intergranular cavities with fine size and homogeneous distribution are beneficial to superplastic deformation.
文摘The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 10^-4- 1.0× 10^-2 s^-1. The maximum elongation 530% of the fine-grained 5083 AI alloy was obtained at 550℃ and 4.17× 10^-4 s^-1. Fracture analysis by scanning electron microscopy （SEM） indicated that the formation of filament （formed by liquid phase） was greatly affected by the tensile temperature and strain rate. The results also showed that the optimum morphology of formed filament was obtained at 550℃ and a strain rate of 4.17× 10^-4 s^-1. The effect of liquid phase on superplastic deformation of the alloy was further discussed.
基金The MEST and KOTEF through the Human Resource Training Project for Regional Innovation
文摘Electrochemical tests were undertaken to determine the optimum conditions in seawater for corrosion protection of friction stir-welded 5083-O Al alloy.Polarization trend observations show that the limiting potential that avoids the effects of hydrogen embrittlement is -1.6 V,corresponding to the crossover point between concentration polarization and activation polarization.However,the optimum protection potential is between -1.5 and -0.7 V since the current density at these values is low in the potentiostatic tests.When a galvanic cell is formed in the seawater,the welds exhibit electrochemically stable trends.Welded parts in galvanic tests with various area ratios are stable and have excellent anticorrosion characteristics.
文摘The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature range of 500-570 ℃ and a strain rate range of 4.17×10^-4 s-1^- 1×10^- 2 s^- 1. Maximum tensile elongation 530% was obtained at 550 ℃ and strain rate ε＆ =4 .17×10^-4 s^-1. Dislocations were observed in grain interiors and at grain boundaries during uniaxial tensile deformation by transmission electronic microscopy （TEM）, respectively. Results show that the grain boundary sliding （GBS） accommodated by dislocation motion is the principal reason for superplastic deformation. The cavities and fracture were observed during uniaxial tensile deformation of the alloy by scanning electronic microscopy （SEM）, indicating that linkage of cavities in large region would induce failure of the material. Moreover, presence of liquid phase at grain boundary also affects the superplastic deformation and behavior of cavities.
文摘The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average size of 15 m and porosity in the range of 0.1 vol. % to 5vol. % . Two distinct TMP procedures are employed to close porosity and refine grain size:extrusion plus rolling and direct rolling. The material processed using the former method exhibits arelatively high superplasticity with a maximum superplastic elongation of 465 % , whereas thatprocessed using the latter method exhibits a maximum superplastic elongation of 295 % . Materialsprocessed using extrusion plus rolling and direct rolling both exhibit similar stress-strainbehavior and strain rate sensitivity factors. The strain rate factors are in the 0.3 to 0.5 range.The difference in their superplastic elongation is possibly the result of differences in grain sizeand available cavity nucleation sites provided by closed gas pores.
基金Project(50225520) supported by the National Found for Distinguished Young Scholars
文摘The effect of temperature distribution on warm forming performance was investigated for 5083-O (Al-Mg) sheet metal blanks. Combined isothermal/non-isothermal FEA with design of experiments tools were used to predict appropriate warm forming temperature conditions for deep drawing and two-dimensional stamping cases. In the investigated temperature range of 25?250 ℃, the formability of Al-5083 alloy is found to be greatly dependent on the temperature distribution of the die and punch. To achieve increased degrees of forming, different temperature levels should be assigned to the corner and body of the die and punch. And the optimal temperature distributions for warm deep drawing and warm two-dimensional stamping are not identical.
