Influence of Incomplete Soil Plugs on Bearing Capacities of Bucket Foundations in Clay

Due to the uneven seabed and heaving of soil during pumping,incomplete soil plugs may occur during the installation of bucket foundations,and the impacts on the bearing capacities of bucket foundations need to be evaluated.In this paper,the contact ratio(the ratio of the top diameter of the soil plug to the diameter of the bucket)and the soil plug ratio(the ratio of the soil heave height to the skirt height)are defined to describe the shape and size of the incomplete soil plug.Then,finite element models are established to investigate the bearing capacities of bucket foundations with incomplete soil plugs and the influences of the contact ratios,and the soil plug ratios on the bearing capacities are analyzed.The results show that the vertical bearing capacity of bucket foundations in homogeneous soil continuously improves with the increase of the contact ratio.However,in normally consolidated soil,the vertical bearing capacity barely changes when the contact ratio is smaller than 0.75,while the bearing capacity suddenly increases when the contact ratio increases to 1 due to the change of failure mode.The contact ratio hardly affects the horizontal bearing capacity of bucket foundations.Moreover,the moment bearing capacity improves with the increase of the contact ratio for small aspect ratios,but hardly varies with increasing contact ratio for aspect ratios larger than 0.5.Consequently,the reduction coefficient method is proposed based on this analysis to calculate the bearing capacities of bucket foundations considering the influence of incomplete soil plugs.The comparison results show that the proposed reduction coefficient method can be used to evaluate the influences of incomplete soil plug on the bearing capacities of bucket foundations.

Pile foundation in alternate layered liquefiable and non-liquefiable soil deposits subjected to earthquake loading

Pile foundations are still the preferred foundation system for high-rise structures in earthquake-prone regions.Pile foundations have experienced failures in past earthquakes due to liquefaction.Research on pile foundations in liquefiable soils has primarily focused on the pile foundation behavior in two or three-layered soil profiles.However,in natural occurrence,it may occur in alternative layers of liquefiable and non-liquefiable soil.However,the experimental and/or numerical studies on the layered effect on pile foundations have not been widely addressed in the literature.Most of the design codes across the world do not explicitly mention the effect of sandwiched non-liquefiable soil layers on the pile response.In the present study,the behavior of an end-bearing pile in layered liquefiable and non-liquefiable soil deposit is studied numerically.This study found that the kinematic bending moment is higher and governs the design when the effect of the sandwiched non-liquefied layer is considered in the analysis as opposed to when its effect is ignored.Therefore,ignoring the effect of the sandwiched non-liquefied layer in a liquefiable soil deposit might be a nonconservative design approach.

Experimental and numerical interpretation on composite foundation consisting of soil-cement column within warm and ice-rich frozen soil

Affected by climate warming and anthropogenic disturbances, the thermo-mechanical stability of warm and ice-rich frozen ground along the Qinghai-Tibet engineering corridor(QTEC) is continuously decreased, which may delay the construction of major projects in the future. In this study, based on chemical stabilization of warm and icerich frozen ground, the soil-cement column(SCC) for ground improvement was recommended to reinforce the foundations in warm and ice-rich permafrost regions. To explore the validity of countermeasures mentioned above, both the original foundation and the composite foundation consisting of SCC with soil temperature of -1.0℃ were prepared in the laboratory, and then the plate loading tests were carried out. The laboratory investigations indicated that the bearing capacity of composite foundation consisting of SCC was higher than that of original foundation, and the total deformation of original foundation was greater than that of composite foundation, meaning that overall stability of foundation with warm and ice-rich frozen soil can be improved by SCC installation. Meanwhile, a numerical model considering the interface interaction between frozen soil and SCC was established for interpretating the bearing mechanism of composite foundation. The numerical investigations revealed that the SCC within composite foundation was responsible for the more applied load, and the applied load can be delivered to deeper zone in depth due to the SCC installation, which was favorable for improving the bearing characteristic of composite foundation. The investigations provide the valuable guideline for the choice of engineering supporting techniques to major projects within the QTEC.

Experimental Study on the Effect of Fine-Grained Soil Content on the Freezing Strength of Aeolian Sand-Cement Interface

In cold regions,understanding the freezing strength of the interface between soil and structure is crucial for designing frost-resistant foundations.To investigate how the content of cement powder in aeolian sand affects this strength,we conducted direct shear tests under various conditions such as different fine-grained soil content,normal stress,and initial moisture content of the soil.By analyzing parameters like soil properties,and volume of ice content,and using the Mohr-Coulomb strength theory to define interface strength,we aimed to indirectly measure the cementation strength of the interface.Our findings revealed that as the particle content increased,the interface stress-strain curves became noticeably stiffer.We also observed a positive linear relationship between freezing strength and silt content,while the initial moisture content of the soil did not significantly impact the strengthening effect of fine-grained soil on freezing strength.Moreover,we discovered that as the powder content increased,the force binding the ice to the interface decreased,while the friction angle at the interface increased.However,the cohesion force at the interface remained relatively unchanged.Overall,our analysis suggests that the increase in freezing strength due to fine-grained soil content is primarily due to the heightened friction between aeolian sand and the interface.

Prediction of compaction parameters for fine-grained soil: Critical comparison of the deep learning and standalone models

A comparison between deep learning and standalone models in predicting the compaction parameters of soil is presented in this research.One hundred and ninety and fifty-three soil samples were randomly picked up from two hundred and forty-three soil samples to create training and validation datasets,respectively.The performance and accuracy of the models were measured by root mean square error(RMSE),coefficient of determination(R2),Pearson product-moment correlation coefficient(r),mean absolute error(MAE),variance accounted for(VAF),mean absolute percentage error(MAPE),weighted mean absolute percentage error(WMAPE),a20-index,index of scatter(IOS),and index of agreement(IOA).Comparisons between standalone models demonstrate that the model MD 29 in Gaussian process regression(GPR)and model MD 101 in support vector machine(SVM)can achieve over 96%of accuracy in predicting the optimum moisture content(OMC)and maximum dry density(MDD)of soil,and outperformed other standalone models.The comparison between deep learning models shows that the models MD 46 and MD 146 in long short-term memory(LSTM)predict OMC and MDD with higher accuracy than ANN models.However,the LSTM models outperformed the GPR models in predicting the compaction parameters.The sensitivity analysis illustrates that fine content(FC),specific gravity(SG),and liquid limit(LL)highly influence the prediction of compaction parameters.

Determination of undrained shear strength using piezocone penetration test in clayey soil for bridge foundation

In order to obtain the reasonable undrained shear strength Su for geotechnical analyses of bridge foundations in Yangtze River floodplain clayey soils, a site-specific study is conducted using the imported piezocone penetration test （CPTu） with dissipation phases at the Fourth Nanjing Yangtze River Bridge construction sites. Taking the values of Su from laboratory tests as references, several existing Su-predicted methods based on CPTu are compared and evaluated. To verify the presented cone factor Nk, additional test sites are selected and examined. The results show that the values of cone factors such as Nkt, Nke, and Nau, depend on the shear test mode and disturbance. Generally, the values of Nke show more scattering than those of Nkt and N△u. For the stratified and layered sediments of the Yangtze River floodplain, it is recommended using the net cone resistance qT to estimate Su and the preliminary cone factor values Nkt are from 7 to 16, with an average of 11. It is also confirmed that the CPTu test, as a new technique in site characterization, can present reasonable parameters for bridge foundations.

Numerical analysis of crack generation within embankment built on expansive soil foundation

In order to analyze the initial cracking behavior of highway embankment in the regions of expansive soil, the changes in peaks of tensile stress and their location on top of the embankment for a typical highway embankment section were simulated by ABAQUS. The simulation results indicate that the matric suction was a concave distribution on top of the expansive soil foundation and that it induced differential deformation of foundation and embankment. The peaks of tensile stress on top of the embankment are not located at a fixed site, but gradually move towards the shoulder following the evaporation duration. When the evaporation intensity is larger, the peak of tensile stress on top of embankment increases at a faster rate following the evaporation duration,and its location is closer to the shoulder. The thicker expansive soil layer helps the peaks of tensile stress to reach the critical tensile stress quickly, but the embankment cannot crack when the expansive soil layer is no more than 1.5m after 30d soil surface evaporation; the higher the embankment, the smaller the peak of tensile stress occurring on top of the highway embankment, and its location will be further away from the shoulder. Therefore, a higher embankment constructed on a thinner expansive soil layer can reduce the crack generation within the highway embankment.

Deep Penetration of Spudcan Foundation into Double Layered Soils

The spudcan foundation has been widely used in offshore engineering for jack-up rigs. However, “punch through' failure often occurs where a stronger soil layer overlays a softer soil layer. In this study, spudcan penetration into double layered soils is investigated numerically. The soil profile is set up as a stronger soil layer overlaying a softer soil layer, with the soil strength ratio (bottom soil strength / top soil strength) varied from 0.1 to 1.0 (1 means uniform soil). The bearing behaviour is discussed and the bearing capacity factors are given for various cases involving different layer thicknesses and different strength ratios of the two clay layers. The development of the plastic zones and the effect of soil self-weight on the bearing capacity are also discussed. From this study, it is found that, when a spudcan is distant from the soil layer boundary, the spudcan can be analysed with single soil layer data. However, when a spudcan becomes closer to the soil boundary layer, the influence of the lower soft soil layer is significant, and the bearing capacity of the spudcan decreases. The critical distance is an indication of the occurrence of “punch through' failure. The critical distance between the spudcan and the layer boundary is larger for a rough spudcan than the one for a smooth one, and the critical distance decreases with increasing soil strength ratio. The depth of cavity formed during initial spudcan penetration depends on the top layer soil strength, soil strength ratio and unit soil self-weight, and the cavity affects the spudcan bearing behaviour as well.

Study of vibrating foundations considering soil-pile-structure interaction for practical applications

An investigation of soil-pile-structure interaction is carried out, based on a large reciprocating compressor installed on an elevated concrete foundation （table top structure）. A practical method is described for the dynamic analysis, and compared with a 3D finite element （FE） model. Two commercial software packages are used for dynamic analysis considering the soilpile-structure interaction （SPSI）. Stiffness and damping of the pile foundation are generated from a computer program, and then input into the FE model. To examine the SPSI thoroughly, three cases for the soil, piles and superstructure are considered and compared. In the first case, the interaction is fully taken into account, that is, both the superstructure and soil-pile system are flexible. In the second case, the superstructure is flexible but fixed to a rigid base, with no deformation in the base （no SSI）. In the third case, the dynamic soil-pile interaction is taken into account, but the table top structure is assumed to be rigid. From the comparison beteen the results of these three cases some conclusions are made, which could be helpful for engineering practice.

Optimization of constitutive parameters of foundation soils k-means clustering analysis

The goal of this study was to optimize the constitutive parameters of foundation soils using a k-means algorithm with clustering analysis. A database was collected from unconfined compression tests, Proctor tests and grain distribution tests of soils taken from three different types of foundation pits： raft foundations, partial raft foundations and strip foundations. k-means algorithm with clustering analysis was applied to determine the most appropriate foundation type given the un- confined compression strengths and other parameters of the different soils.

Calculation of Hydro-Dynamic Stability of the Soil Inside Bucket in the Process of Bucket Foundation Penetration

The offshore platform with bucket foundations is a;new type of offshore platform that distinguishes from traditional template platforms by replacing driven piles with bucket foundations. The suction penentration of bucket foundation is a complicated hydro-dynamic process. The key of this process is the seepage field caused by the difference of pressure applied on purpose inside and outside the bucket. The appearance and developement of seepage field has a decisive influence on the suction penetration process. In this study, the finite element analysis method is applied to the dynamic simulation of the seepage field of suction penetration of bucket foundation. A criterion is suggested to distinguish the hydro-dynamic stability of the soil inside the bucket according to the critical hydraulic gradient method. The reliability of the model and its applicability to engineering practice have been proved through comparison between the results of model test and finite element calculation.

Experimental and Theoretical Study on the Self-Weight Penetration Velocity of Suction Anchor Foundations in Sand

The application of the wellhead suction anchor in the second production test of natural gas hydrates(NGHs)in the South China Sea(SCS)was met with success.This design incorporates a central conductor guide pipe,which distinguishes it from traditional suction foundations.However,this addition resulted in a relatively high penetration resistance and a shallower penetration depth at the self-weight penetration stage.To mitigate this issue,the current study proposes an optimized design where the end of the suction foundation is sharpened.The installation characteristics of the traditional suction foundation and new suction foundation during self-weight penetration into sand are studied through laboratory tests and theoretical analysis.The flat and sharpened bottom shapes are considered in the traditional and new suction models.The effects of the initial penetration velocity on the initial penetration depth and soil plug and impact cavity characteristics are systematically studied.The results show that the self-weight penetration depth of the foundation with a sharpened bottom is 44.5%deeper than that of the foundation with a flat bottom.There are cavities around the foundation at the self-weight penetration stage,and the penetration depth is overestimated by 15%-30%.Finally,a model for predicting the penetration depth of the new suction foundation is proposed.

Research of deformation prediction method of soft soil deep foundation pit

In view of the characteristics of soft soil deep foundation pit for the construction and geotechnical characteristics of the special medium,it is difficult to calculate theoreti- cally accurately structural deformation of the foundation pit,so in the course of excavation on the construction of the information is particularly important.The analysis and compari- son of several popular non-linear forecasting methods,combined with the actual projects, set up a grey theoretical prediction model,time series forecasting model,improved neural network model to predict deformation of the foundation pit.The results show that the use of neural network to predict with high accuracy solution,it is the foundation deformation prediction effective way in underground works with good prospects.

NUMERICAL ANALYSIS OF SOIL PLUG INSIDE SUCTION FOUNDATIONS DURING SUCTION PENETRATION BY DISCRETE ELEMENT METHOD

The phenomenon of the soil plug usually rising inside the suction foundations during suction penetration was quantitatively described and predicted. The formation process of the soil plug was simulated and calculated by DEM （discrete element method） model. The seepage flow, the self-weight of soil, the friction on the chamber wall as well as the suction inside the chamber are considered as the main external forces in the process. The results are compared with a set of laboratory model tests performed by using three soil types （sand, silty clay and clay） in the Bohai Sea area. The heights of soil plug from numerical estimations are lower than those from model test results, mainly because the suction pressure and friction resistance are applied in an ideal way under the numerical simulation.

Performance assessment of borehole arrangements for the design of rectangular shallow foundation systems

This study proposes a framework to evaluate the performance of borehole arrangements for the design of rectangular shallow foundation systems under spatially variable soil conditions. Performance measures are introduced to quantify, for a fixed foundation layout and given soil sounding locations, the variability level of the foundation system bearing capacities in terms of their mean values and standard deviations. To estimate these measures, the recently proposed random failure mechanism method (RFMM) has been adopted and extended to consider any arrangement of rectangular foundations and boreholes. Hence, three-dimensional bearing capacity estimation under spatially variable soil can be efficiently performed. Several numerical examples are presented to illustrate the applicability of the proposed framework, including diverse foundation arrangements and different soil correlation structures. Overall, the proposed framework represents a potentially useful tool to support the design of geotechnical site investigation programs, especially in situations where very limited prior knowledge about the soil properties is available.

Estimation of Heights of Soil Plug Inside Bucket Foundations During Suction Penetration by Deformable Discrete Element Modeling

The soil plug phenomenon involving the rising of the surface soil inside the bucket chamber under the suction pressure and seepage forces was simulated and calculated by deformable discrete element method (DDEM) models. The seepage forces, the effective gravity of soil, the friction on the chamber wall and the suction inside the chamber are considered as the main external forces of DDEM specimen. Three typical types of soil (silty clay, silt and sand) in the Bohai Sea are set as the main environmental conditions in the formation process of soil plug. It is found that the heights of soil plug simulated by DDEM models are 161.85 mm in silty clay, 125.22 mm in silt and 167.56 mm in sand, which are close to model test results and higher than those estimated by discrete element method (DEM). DDEM is an effective method to estimate and predict the heights of soil plug before suction penetration of bucket foundations on site.

Design parameter optimization of beam foundation on soft soil layer with nonlinear finite element

Finite element method was performed to investigate the influences of beam stiffness, foundation width and cushion thickness on the beating capacity of beam foundation on underlying weak laminated clay. The comparison between numerical results and results from field test including plate-bearing test and foundation settlement observation shows reasonable agreement. According to the numerical results, the beam width, length, cross section and cushion thickness were optimized. The results show that the stresses in subgrade soil decrease greatly with increasing the cushion thickness and width of foundation. However, the foundation settlement and influencing depth of displacement also increase correspondingly under conditions of relatively thinner cushion thickness. For the foundations on underlying weak layer, increasing foundation width merely might be inadequate for improving the bearing capacity, and the appropriate width and cushion thickness depend on the response of subgrade. A comparison between rigid and flexible beams was also discussed. The influence of a flexible beam foundation on subgrade is relatively smaller under the same loading conditions, and the flexible beam foundation appears more adaptable to various subgrades. The proposed flexible beam foundation was adopted in engineering. According to the calculation results, beam width of 2.4 m and cushion thickness of 0.8 m are proposed, and a flexible beam foundation is applied in the optimized design, which is confirmed reasonable by the actual engineering.

New artificial boundary condition for saturated soil foundations

Anew artificial boundary model based on multi-directional transmitting and viscous-spring artificial boundary theories is proposed to absorb stress waves in a saturated soil foundation in dynamic analysis. Since shear waves （S-waves） are the same in a saturated soil foundation and a single-phase medium foundation, a tangential visco-elastic boundary condition for a single-phase medium foundation can also be used for saturated soil foundations. Thus, the purpose of the artificial boundary proposed in this paper is primarily to absorb two types of P-waves in a saturated soil foundation. The main idea is that the stress of the P-waves in the saturated soil foundation is decomposed into two types. The first type of stress, δra＇ is absorbed by the first artificial boundary. The second type of stress, δrb, is balanced by the stress generated by the second artificial boundary. Ultimately, both types of P-waves （fast-P-waves and slow-P-waves） are absorbed by the artificial boundary model proposed in this paper. In particular, note that the fast-P-waves and slow-P-waves are absorbed at the position of the first boundary. Thus, the artificial boundary model proposed herein can simultaneously absorb P-fast waves, P-slow waves and shear waves. Finally, a numerical example is given to examine the proposed artificial boundary model, and the results show that it is very accurate.

Engineering Geological Zoning of Soft-Soil Foundation Based on Combination Weighting and Extension Methods

Different criteria and factors are used in different methods of soft soil foundation settlement calculation and engineering geological zoning.The methods used are not universally suitable for complex geological environments.The post-construction settlement of soft soil foundations are especially large and difficult to calculate.In addition,there are many deficiencies in the current methods used for engineering geological zoning.Focusing on the need of establishing engineering geological zoning for areas with soft soil foundations in the Tianjin Marine Economic Area,combination weighting and extension methods were introduced.An evaluation model for the settlement of soft soil foundations was established using multiple factors and large amounts of data.This evaluation model is accurate and objective for delineating engineering geological zoning.These methods eliminate deficiencies by considering both objective and subjective factors,and help obtain an objective and accurate result.

Test on Muddy Soil Reinforcement by Negative Pressure and Electro-Osmosis Inside Cover-Bearing-Type Bucket Foundation for Offshore Wind Turbines

Cover-bearing-type bucket foundation for offshore wind turbines has been paid more and more attention due to its low cost and great bearing capacity. In order to ensure the cover-bearing mode, the muddy soil inside the bucket foundation should be reinforced by some soil consolidation methods, such as negative pressure and electro-osmosis. Firstly, tests were conducted to obtain the reasonable current density. Meanwhile, to improve the electro-osmotic speed and effectiveness, other factors such as intermittent power and layout of electrode, were also studied in the tests. Then, the soil reinforcing tests by negative pressure combined with electro-osmosis were performed for the muddy soil consolidation inside the bucket foundation. The results showed that soil reinforcement by negative pressure was quicker and more obvious during the early phase, and electro-osmotic method can affect more range of soil by rational arrangement of electrodes. Compared with negative pressure, the electro-osmotic method was a continuous and relatively slow process of reinforcement, which was complementary to the negative pressure method. The voltage value of electro-osmosis had little effect on the muddy soil reinforcement inside the bucket foundation, and 1.5 A was chosen as the most reasonable current value for scale model testing in the electro-osmotic method.