Collapse Behavior of Pipe-Framed Greenhouses with and without Reinforcement under Snow Loading:A 3-D Finite Element Analysis

The present paper first investigates the collapse behavior of a conventional pipe-framed greenhouse under snow loading based on a 3-D finite element analysis,in which both geometrical and material non-linearities are considered.Three snow load distribution patterns related to the wind-driven snow particle movement are used in the analysis.It is found that snow load distribution affects the deformation and collapse behavior of the pipe-framed greenhouse significantly.The results obtained in this study are consistent with the actual damage observed.Next,discussion is made of the effects of reinforcements by adding members to the basic frame on the strength of the whole structure,in which seven kinds of reinforcement methods are examined.A buckling analysis is also carried out.The results indicate that the most effective reinforcement method depends on the snow load distribution pattern.

Stress Distributions Created by Short and Regular Implants Placed in the Anterior Maxilla at Different Angles: A Finite Element Analysis

Although short implants are seen as alternative treatments that require additional surgical techniques in posterior region, they can be applied to anterior maxilla and various studies are required on this subject. The purpose of this study was to examine and compare the peak von Mises stress distributions in the crown, implant and abutment by using finite element analysis (FEA). Besides, a comparison of the implant-abutment connection types in the short implant with the FEA method was established. A short implant (4 × 5 mm) with a taper-lock connection and a regular implant (4 × 9 mm) with a screw connection were used in maxillary central incisor tooth area. Three different titanium abutments with 0?, 15? and 25? angles were used for abutments. In addition, in order to determine whether the stress change in short implants is due to the length of the implant-abutment connection, a screw was designed for a short implant and it was also evaluated in the same three angles. A total of three groups and nine models were generated. 114.6N load was applied to the cingulum area of the crown at an angle of 135? to the long axis of the crowns. A torque load of 25 Ncm was applied to the regular and short implant screw. Von Mises stress distributions of implants, abutments and crowns were evaluated by using FEA. Increased angle in implants increased von Mises stress values of implant, abutment and crown. Screw connection was found higher at all angles in short implants. Close values were found at different angles in taper-lock short implant crowns. The length and the angle in the bone of implant with the type of implant-abutment connection results in the accumulated stress values. Clinical Implications Taper implant-abutment connection system was found to be more promising in terms of stress accumulation in crowns. Although the amount of stress on the abutment increased due to the length of the implant in short implants, taper implant-abutment connection system slightly reduced related to this increase.

Study on Development of Light Aluminum Step by Using Finite Element Analysis

In order to ensure the safe operation of the escalator,the step as a part of transporting passengers,the design will consider a high safety factor,which will increase the weight,the manufacturing cost,and the energy consumption of the steps band operation.Therefore,in order to reduce the weight and ensure the strength and stiffness of the step,through the optimization design,the number of reinforcing rib supports of the step tread plate and riser plate is increased,and the thickness of the step tread plate and riser plate is moderately reduced,so as to achieve the purpose of reducing the weight of the step and reducing the manufacturing cost and operating energy consumption.Through the finite element analysis and testing of the new type step design,Its strength and stiffness fully meet the requirements of GB 16899-2011 and EN 115-1:2017 standards,and the breaking force also meets the industry standards,so that the manufacturing and operating costs of the product can be reduced to improve the competitiveness of the product market.

Three-dimensional Finite Element Analysis of the Mechanical Properties of Helical Thread Connection

Conventional analytical and numerical methods for the mechanical properties of helical threads are relied on many assumptions and approximations and thus hardly yield satisfied results. A parameterized 3D finite element model of bolted joints with real helical thread geometry is established and meshed with refined hexahedral elements. The Von Mises plasticity criterion, kinematic hardening rule of materials and interfacial contacts are employed to make it possible for the suggested model be able to approach real assembly conditions. Then, the mechanical properties of bolted joints with different thread pitches, thread numbers and modular ratios are investigated, including the contact pressure distribution at joint interfaces, the axial load distribution and stress concentration in screw threads during the loading and unloading process. Simulation results indicate that the load distribution in screw threads produced by the suggested model agrees well the results from CHEN’s photoelastic tests. In addition, an interesting phenomenon is found that tightening the bolt with a large preload first and then adjusting the clamping force by unloading can make the load distribution more uniform and reduce the maximum residual equivalent stress in thread roots by up to 40%. This research provides a simple and practical approach to constructing the 3D finite element model and predicting the mechanical properties of helical thread connection.

Finite element analysis of multi-piece post-crown restoration using different types of adhesives

The multi-piece post-crown technique is more effective in restoring residual root than other restoration techniques.Various types of adhesives have different material properties that affect restoration.Therefore,the choice of adhesive is particularly important for patients.However,the effect of different kinds of adhesives was not too precise by experimental methods when concerning about individual differences of teeth.One tooth root can only be restored with one type of adhesive in experiment.After the mechanical test,this tooth root cannot be restored with other adhesives.With the help of medical imaging technology,reverse engineering and finite element analysis,a molar model can be reconstructed precisely and restored using different types of adhesives.The same occlusal and chewing loads were exerted on the same restored residual root models with different types of adhesives separately.Results of von Mises stress analysis showed that the adhesives with low Young’s modulus can protect the root canal effectively.However,a root canal concentration is apparently produced around the root canal orifice when chewing.Adhesives with large Young’s modulus can buffer the stress concentration of the root canal orifice.However,the root canal tissue may be destroyed because the adhesive is too hard to buffer the load.

Finite element analysis of stiffness and static dent resistance of aluminum alloy double-curved panel in viscous pressure forming

The static dent resistance performance of the aluminum alloy double-curved panel formed using viscous pressure forming (VPF)was studied by finite element analysis,which mainly considers the forming process conditions.The whole simulation consisting of three stages,i.e.,forming,spring-back and static dent resistance,was carried out continuously using the finite element code ANSYS.The influence of blank holder pressure(BHP)and the drawbead on the stiffness and the static dent resistance of the panels formed using VPF was analyzed.The results show that the adequate setting of the drawbead can increase the plastic deformation of the double-curved panel,which is beneficial to the initial stiffness and the static dent resistance.There is an optimum BHP range for the stiffness and the static dent resistance.

Influence of Various Materials on Biomechanical Behavior of Endocrown-Restored, Endodontically-Treated Mandibular First Molar: A 3D-Finite Element Analysis

To evaluate the effect of restorative materials on stress distribution of endodontically treated teeth, the 3D models of an endodontically treated mand^ular first molar, restoration, and cement layer were created. Three different materials （composite resin, ceramage and ceramic） were studied and two loading conditions （vertical and oblique load） were simulated. Mohr-Coulomb failure criterion of enamel, dentine, endocrown and cement were evaluated separately. It is indicated that under both loading conditions, the highest values of Mohr-Coulomb failure criterion were observed in Ceramage-restored group for remaining tooth structure while in ceramic-restored group for the restoration. Compared to composite resin and Ceramage, ceramic endocrown transferred less stress, namely was more protective to the tooth structure.

Structure,Orientation and Finite Element Analysis of the Tail Club of Mamenchisaurus hochuanensis

The structure and orientation of the posterior extremity （tail club） of the caudal vertebrae of Mamenchisaurus hochuanensis Young and Chao, 1972 from the Upper Jurassic Shangshaximiao Formation has been analyzed to determine the tail club function using Finite Element Analysis. Of the four caudal vertebrae composing the tail club, the second largest （C＂1＂） was probably the most proximal, and is fixed with the preceding sequence of the caudal vertebrae, whereas the smallest （C＂4＂） is free and forms the termination of the tail club. Our analysis also suggests that the tail club is more efficient in lateral swinging rather than up-and-down motion, and that the best region for the tail club to impact is at the spine of the largest of the four caudals （C＂2＂）, with a maximum load for impact at about 450 N. The tail club of Mamenchisaurus hochuanensis probably also had limitations as a defense weapon and was more possibly a sensory organ to improve nerve conduction velocity to enhance the capacity for sensory perception of its surroundings.

Finite Element Analysis of 3-D Electromagnetic Field in Bloom Continuous Casting Mold

Three-dimensional finite element model of electromagnetic stirrer was built to predict magnetic field in a bloom continuous casting mold for steel during operation. The effects of current intensity, current frequency, and mold copper plate thickness on the magnetic field distribution in the mold were investigated. The results show that the magnetic induction intensity increases linearly with the increase in current intensity and decreases with the increase in current frequency. Increasing current intensity and frequency is available in increasing the electromagnetic force. The Joule heat decreases gradually from surface to center of bloom, and a maximum Joule heat can be found on corner of bloom. The prediction of magnetic induction intensity is in good agreement with the measured values.

Nonlinear Finite Element Analysis of Ocean Cables

This study has focused on developing numerical procedures for the dynamic nonlinear analysis of cable structures subjected to wave forces and ground motions in the ocean. A geometrically nonlinear finite element procedure using the isoparametric curved cable element based on the Lagrangian formulation is briefly summarized. A simple and accurate method to determine the initial equilibrium state of cable systems associated with self-weights, buoyancy and the motion of end points is presented using the load incremental method combined with penalty method. Also the Newmark method is used for dynamic nonlinear analysis of ocean cables. Numerical examples are presented to validate the present numerical method.

3-D FINITE ELEMENT ANALYSIS OF THE EFFECT OF WELDING RESIDUAL STRESS ON HYDROGEN DIFFUSION IN HYDROGEN CONTAINED ENVIRONMENT

The hydrogen distribution of 16MnR steel weldment in hydrogen contained environment was calculated using the finite element method （ FEM）. The effect of welding residual stress on hydrogen diffusion has been discussed using a 3-D sequential coupling finite element analysis procedure complied by Abaqus code. The hydrogen diffusion coefficient in weld metal, the heat affected zone （HAZ）, and the base metal of the 16MnR steel weldment were measured using the electrochemical permeation technique. The hydrogen diffusion without the effect of stress was also calculated and compared. Owing to the existence of welding residual stress, the hydrogen concentration was obviously increased and the hydrogen wouM diffuse and accumulate in the higher stress region.

Finite Element Analysis of the Contact Mechanics of Ceramic-on-Ceramic Hip Resurfacing Prostheses

Ceramics are good alternative to metal as bearing couple materials because of their better wear resistance. A Finite Element(FE) study was performed to investigate the contact mechanics and stress distribution of Ceramic-on-Ceramic (COC) hip resurfacingprostheses. It was focused in particular on a parametric study to examine the effects of radial clearance, loading,alumina coating on the implants, bone quality, and fixation of cup-bone interface. It was found that a reduction in the radialclearance had the most significant effect on the predicted contact pressure distribution among all of the parameters considered inthis study. It was determined that there was a significant influence of non-metallic materials, such as the bone underneath thebearing components, on the predicted contact mechanics. Stress shielding within the bone tissue was found to be a major concernwhen regarding the use of ceramic as an alternative to metallic resurfacing prostheses. Therefore, using alumina implantswith a metal backing was found to be the best design for ceramic resurfacing prostheses in this study. The loading, bone quality,and acetabular cup fixation conditions were found to have only minor effects on the predicted contact pressure distribution alongthe bearing surfaces.

Pedicle Screw Fixation with Kyphoplasty Decreases the Fracture Risk of the Treated and Adjacent Non-treated Vertebral Bodies:a Finite Element Analysis

Adjacent vertebral fractures are common in patients with osteoporotic vertebral compression fractures（OVCFs） after kyphoplasty.This finite element study was to examine whether short segment pedicle screw fixation（PSF） with kyphoplasty may decrease the fracture risk of the treated and adjacent non-treated vertebrae after kyphoplasty for OVCFs.By simulating cement augmentation with or without short segment pedicle screw fixation（PSF）,two tridimensional,anatomically detailed finite element models of the T10–L2 functional spinal junction were developed.The insertion of pedicle screws into the intact vertebra apparently decreased the stress distribution of the treated vertebra in vertical compression and other load situations.The stress distribution in the bone structures of the intact vertebra adjacent to the intact-screwed vertebra was much less than that in the one adjacent to the treated vertebra.The insertion of pedicle screws into the intact vertebra greatly decreased the maximum displacement of the cortical bones and cancellous bones of the vertebrae.Our results indicated that short segment PSF with kyphoplasty may decrease the fracture risk of the treated and adjacent non-treated vertebrae in the management of OVCFs.

Nonlinear finite element analysis of three implant-abutment interface designs

The objective of this study was to investigate the mechanical characteristics of implant-abutment interface design in a dental implant system, using nonlinear finite element analysis （FEA） method. This finite element simulation study was applied on three commonly used commercial dental implant systems： model I, the reduced-diameter 3i implant system （West Palm Beach, FL, USA） with a hex and a 12-point double internal hexagonal connection; model II, the Semados implant system （Bego, Bremen, Germany） with combination of a conical （45° taper） and internal hexagonal connection; and model III, the Br,~nemark implant system （Nobel Biocare, Gothenburg, Sweden） with external hexagonal connection. In simulation, a force of 170 N with 45°oblique to the longitudinal axis of the implant was loaded to the top surface of the abutment. It has been found from the strength and stiffness analysis that the 3i implant system has the lowest maximum yon Mises stress, prirlcipal stress and displacement, while the Br^nemark implant system has the highest. It was concluded from our preliminary study using nonlinear FEA that the reduced-diameter 3i implant system with a hex and a 12-point double internal hexagonal connection had a better stress distribution, and produced a smaller displacement than the other two implant systems.

A MULTI-COUPLED FINITE ELEMENT ANALYSIS OF RESISTANCE SPOT WELDING PROCESS

A two-dimensional axisymmetric finite element model is developed to analyze the transient thermal and mechanical behaviors of the Resistance Spot Welding （RSW） process using commercial software ANSYS. Firstly a direct-coupled electrical-thermal Finite Element Analysis （FEA） is performed to analyze the transient thermal characteristics of the RSW process. Then based on the thermal results a sequential coupled thermo-elastic-plastic analysis is conducted to determine the mechanical features of the RSW process. The thermal history of the whole process and the temperature distribution of the weldment are obtained through the analysis. The mechanical features, including the distributions of the contact pressure at both the faying surface and the electrode-workpiece interface, the stress and strain distributions in the weldment and their changes during the RSW process, the deformation of the weldment and the electrode displacement are also calculated.

Finite element analysis of keyhole plasma arc welding based on an adaptive heat source mode

An adaptive heat source mode is proposed to account for the keyhole effect and the characteristics of volumetric distribution along the direction of the workpiece thickness. Finite element analysis of the temperature field in keyhole plasma arc welding is conducted and the weld geometry is obtained. The predicted results are in agreement with the measured ones.

Finite element analysis of controlling the TC4 thin plate weldment wave-like deformation by welding with impacting rotation

The new technology of welding with impacting rotation is put forward to decrease the wave-like deformation of the TC4 thin plate weldment. The thermal stress and strain are vital to understand the mechanism of controlling the wave-like deformation. In order to know the development of internal thermal stress and strain, finite element method is utilized for- the stress and strain are difficult to be investigated by experimental methods during the welding process. Temperature field, thermal stress evolution and distortion of thin plate are compared with the test results such as weld thermal cycle, residual stress sectioning measurement, and the deflection of the thin plate respectively. By the finite element analysis and test results verification, the meehaaism of the technology to control the wave-like deformation is brought forward, non-uniform thermal elastic strain between compressive plastic region and elastic extensive region is diminished by a certain amount of extensive plastic deformation by welding with impacting rotation process.

Numerical simulation of low-concentration CO_(2) adsorption on fixed bed using finite element analysis

Accurately predicting distributions of concentration and temperature field in fixed-bed column is essential for designing adsorption processes.In this study,a two-dimensional(2D),axisymmetric,nonisothermal,dynamic adsorption model was established by coupling equations of mass,momentum and energy balance,and solved by finite element analysis.The simulation breakthrough curves fit well with the low-concentration CO_(2) adsorption experimental data,indicating the reliability of the established model.The distributions of concentration and temperature field in the column for CO_(2) adsorption and separation from CO_(2)/N_(2) were obtained.The sensitivity analysis of the adsorption conditions shows that the operation parameters such as feed flow rate,feed concentration,pellet size,and column height-to-diameter ratio produce a significant effect on the dynamic adsorption performance.The multi-physics coupled 2D axisymmetric model could provide a theoretical foundation and guidance for designing CO_(2) fixed-bed adsorption and separation processes,which could be extended to other mixed gases as well.

Finite element analysis of ionic liquid gel soft actuator

A new type of soft actuator material-ionic liquid gel （ILG）, which consists of HEMA, BMIMBF4, and TiO2, can be transformed into gel state under the irradiation of ultraviolet （UV） light. In this paper, Mooney-Rivlin hyperelastic model of finite element method is proposed for the first time to study the properties of the ILG. It has been proved that the content of TiO2 has a great influence on the properties of the gel, and Young＇s modulus of the gel increases with the increase of its content, despite of reduced tensile deformation. The results in this work show that when the TiO2 content is 1.0 wt%, a large tensile deformation and a strong Young＇s modulus can be obtained to be 325% and 7.8 kPa, respectively. The material parameters of ILG with TiO2 content values of 0.2 wt%, 0.5 wt%, 1.0 wt%, and 1.5 wt% are obtained, respectively, through uniaxial tensile tests, including C10, C01, C20, C11, C02, C30, C21, C12, and C03 elements. In this paper, the large-scaled general finite element software ANSYS is used to simulate and analyze the ILG, which is based on SOLID186 element and nonlinear hyperelastic Mooney-Rivlin model. The finite element simulation analysis based stress-strain curves are almost consistent with the experimental stress-strain curves, and hence the finite element analysis of ILG is feasible and credible. This work presents a new direction for studying the performance of soft actuator for the ILG, and also contributes to the design of soft robot actuator.

Finite element analysis of temperature field during multi-layer multi-pass weld-based rapid prototyping

During weld-bused rapid prototyping, the component experiences complex thermal process. In this paper, the temperature field evolution, thermal cycle characteristics, and temperature gradients of multi-layer multi-puss weld-based rapid prototyping are investigated using three-dimensional finite element models presented. The single-puss weld-bused rapid prototyping experiment is carried out. Thermal cycles calculated agree with experimental measurements. Furthermore, simulated results indicate that there exist the pre-heating effect of the fore layer and the post-heating effect of the rear layer in the multi-layer multi-pass weld-based rapid prototyping. In the first layer, the heat accumulates obviously. After the first layer, the dimension increase of the high temperature region behind the molten pool is not obvious. The heat diffusion condition in the first layer is the best, the heat diffusion condition in the second layer is the worst, and the heat diffusion conditions in the higher layers improve gradually.