Analytical Solution and Simplified Formula for Added Mass of Horizontal and Vertical Motions of Truncated Cylinders Under Earthquake Action

This paper investigates the hydrodynamic characteristics of floating truncated cylinders undergoing horizontal and vertical motions due to earthquake excitations in the finite water depth.The governing equation of the hydrodynamic pressure acting on the cylinder is derived based on the radiation theory with the inviscid and incompressible assumptions.The governing equation is solved by using the method of separating variables and analytical solutions are obtained by assigning reasonable boundary conditions.The analytical result is validated by a numerical model using the exact artificial boundary simulation of the infinite water.The main variation and distribution characteristics of the hydrodynamic pressure acting on the side and bottom of the cylinder are analyzed for different combinations of wide-height and immersion ratios.The added mass coefficient of the cylinder is calculated by integrating the hydrodynamic pressure and simplified formulas are proposed for engineering applications.The calculation results show that the simplified formulas are in good agreement with the analytical solutions.

Application and analysis of functionally graded piezoelectrical rotating cylinder as mechanical sensor subjected to pressure and thermal loads

The exact thermoelastic analysis of a functionally graded piezoelectrical （FGP） rotating cylinder is investigated analytically. The cylinder is subjected to a com- bination of electrical, thermal, and mechanical loads simultaneously. The structure is a simplified model of a rotational sensor or actuator. The basic governing differential equation of the system is obtained by using the energy method. A novel term, named as the additional energy, is introduced to exact the evaluation of the energy functional. The solution to the governing differential equation is presented for two types of boundary conditions including free rotating and rotating cylinders exposed to the inner pressure. The effect of the angular velocity is investigated on the radial distribution of various components. The mentioned structure can be considered as a sensor for measuring the angular velocity of the cylinder subjected to the pressure and temperature. The obtained results indicate that the electrical potential is proportional to the angular velocity.

Stress analytical solution for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform distributed pressure

The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0°,45° and 90°,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.

MATHEMATIC MODEL AND ANALYTIC SOLUTION FOR CYLINDER SUBJECT TO UNEVEN PRESSURES

According to the inverse solution of elasticity mechanics, a stress function is constructed which meets the space biharmonic equation, this stress functions is about cubic function pressure on the inner and outer surfaces of cylinder. When borderline condition that is predigested according to the Saint-Venant＇s theory is joined, an equation suit is constructed which meets both the biharmonic equations and the boundary conditions. Furthermore, its analytic solution is deduced with Matlab. When this theory is applied to hydraulic bulging rollers, the experimental results inosculate with the theoretic calculation. Simultaneously, the limit along the axis invariable direction is given and the famous Lame solution can be induced from this limit. The above work paves the way for mathematic model building of hollow cylinder and for the analytic solution of hollow cvlinder with randomly uneven pressure.

New Formulas of Earth Pressure on Large Successive Cylinders

The retaining wall made of large successive cylinders is a kind of structure which draws much attention in coastal engineering of China. The earth pressure on the arched back of large successive cylinders is different from that on the plane back of a general wall. On the basis of equilibrium of forces on the strip element taken from the soil between two cylinders, the differential equation is established and the analytic solution to the equation is obtained. The formulas of earth pressure on large successive cylinders are given in this paper. The distribution of earth pressure around the circle given by the present formulas is different from that given by the formulas commonly used at present, but it is identical with that measured in the model test.

Pressure Angle Effect of Concave Cylinder Surface on Motion Characteristics of Fiber Placement Machine

There are amounts of issues to be resolved in the process of designing the fiber placement trajectory of the cylindrical component,such as the interference between the machine and the component and the over-travel of the axis of rotation on the fiber placement head.When the pressure on the cylinder surface inclines in a certain direction or at an angle within the normal plane,the motion characteristics of the rotation axis will be different.This paper analyzes the pressure angle effect of the concave cylinder surface on the motion features of a fiber placement machine.The placement area is enlarged by tilting pressure with the same lifting stroke,which is significant in preventing interference and selecting post-processing algorithm.

Analysis of Static Pressure in Area between Back Plate and Cylinder of a Carding Machine with CFD

To analyze static pressure between back plate and cylinder in an A186 carding machine,a fluid model is established. The model takes into account static pressure of airflow near back plate with the numerical simulation method of Computational Fluid Dynamics (CFD) in FLUENT software. The result of the simulation in the model shows that static pressure in this area quickly increases to its maximum then rapidly decreases to a lower fixed value from inlet to outlet along a zone between back plate and cylinder. Both rotating speeds of the cylinder and the taker-in affect static pressure from the inlet to the outlet,of which the cylinder rotating speed has more influence than that of taker-in. Numerical simulations reveal that static pressure on surface of back plate are in good agreement with the former result of experimental analysis.

Cyclic moving average control approach to cylinder pressure and its experimental validation

Cyclic variability is a factor adversely affecting engine performance. In this paper a cyclic moving average regulation approach to cylinder pressure at top dead center （TDC） is proposed, where the ignition time is adopted as the control input. The dynamics from ignition time to the moving average index is described by ARMA model. With this model, a one-step ahead prediction-based minimum variance controller （MVC） is developed for regulation. The performance of the proposed controller is illustrated by experiments with a commercial car engine and experimental results show that the controller has a reliable effect on index regulation when the engine works under different fuel injection strategies, load changing and throttle opening disturbance.

Numerical evaluation of an autofrettaged thick-walled cylinder under dynamically applied axially non-uniform internal service pressure distribution

A dynamical moving pressure structural numerical calculation model using the internal ballistics calculation pressure-time results was constituted and the vicinity of the internal ballistics and quasiinternal ballistics structural model was checked. The Von Mises stresses obtained by the dynamical structural numerical model calculations and the Von Mises stresses calculated from the shot test strain measurements were compared. The difference for the worse case was 20% and for the best case was 0.1%.Furthermore, the model gave better agreement for the higher charge masses. The numerical structural quasi-internal ballistics computation model created was verified for the top charge mass which represents the highest stress condition and used in a gun barrel design.

A SOLUTION OF COSINE PRESSURES ON A HOLLOW CYLINDER AND THE LIMIT WHEN k→0

A new stress function is found in this paper and then the problems of cosine pressures on a hollow cylinder are solved with the new stress function, which provides the basis for the solution of the problems of space symmetrical deformation of a hollow cylinder. When the pressures do not vary in the axial direction, that is, when the lame formulae can be deduced.

Transportation-cyber-physical-systems-oriented engine cylinder pressure estimation using high gain observer

In transportation cyber-physical-systems （T-CPS）, vehicle-to-vehicle （V2V） communications play an important role in the coordination between individual vehicles as well as between vehicles and the roadside infrastructures, and engine cylinder pressure is significant for engine diagnosis on-line and torque control within the information exchange process under V2V communications. However, the parametric uncertainties caused from measurement noise in T-CPS lead to the dynamic performance deterioration of the engine cylinder pressure estimation. Considering the high accuracy requirement under V2V communications, a high gain observer based on the engine dynamic model is designed to improve the accuracy of pressure estimation. Then, the analyses about convergence, converge speed and stability of the corresponding error model are conducted using the Laplace and Lyapunov method. Finally, results from combination of Simulink with GT- Power based numerical experiments and comparisons demonstrate the effectiveness of the proposed approach with respect to robustness and accuracy.

Safety estimation of high-pressure hydraulic cylinder using FSI method

Hydraulic cylinder is a primary component of the hydraulic valve systems.The numerical study of hydraulic cylinder to evaluate the stress analysis,the life assessment and the performance of operation characteristics in hydraulic cylinder were described.The calculation of safety factor,fatigue life,piston chamber pressure,rod chamber pressure and the change of velocity of piston with flow time after the beginning of hydraulic cylinder were incorporated.Numerical analysis was performed using the commercial CFD code,ANSYS with unsteady,dynamic mesh model,two-way FSI(fluid-structure interaction)method and k-εturbulent model.The internal pressure in hydraulic cylinder through stress analysis show higher than those of the yield strength.

Cylinder Pressure Prediction of An HCCI Engine Using Deep Learning

Engine tests are both costly and time consuming in developing a new internal combustion engine.Therefore,it is of great importance to predict engine characteristics with high accuracy using artificial intelligence.Thus,it is possible to reduce engine testing costs and speed up the engine development process.Deep Learning is an effective artificial intelligence method that shows high performance in many research areas through its ability to learn high-level hidden features in data samples.The present paper describes a method to predict the cylinder pressure of a Homogeneous Charge Compression Ignition(HCCI)engine for various excess air coefficients by using Deep Neural Network,which is one of the Deep Learning methods and is based on the Artificial Neural Network(ANN).The Deep Learning results were compared with the ANN and experimental results.The results show that the difference between experimental and the Deep Neural Network(DNN)results were less than 1%.The best results were obtained by Deep Learning method.The cylinder pressure was predicted with a maximum accuracy of 97.83%of the experimental value by using ANN.On the other hand,the accuracy value was increased up to 99.84%using DNN.These results show that the DNN method can be used effectively to predict cylinder pressures of internal combustion engines.

Retrofit on Low Pressure Cylinder Flow Path Succeeded

The retrofit on flow path of low pressure cylinder of domestic made 200 MW steam turbine undertaken by Longwei Power Generation Technology Service Company Ltd by using Westinghouse technology was successful for the first time on the No. 5 unit of Zhenhai Prover Plant. Zhejiang Province. The test carried out by the Xi’an Thermal Power Research Institute showed that the thermal efficiency after the retrofit

An approach for optimization of the wall thickness (weight) of a thick-walled cylinder under axially non-uniform internal service pressure distribution

Today, improving the weight/load carrying capacity ratio of a part is the matter of studies in most of the scientific and industrial areas.Autofrettage dimensions, the amount of material removed from outer and inner radius while manufacturing and the service pressure applied affect the residual stress distribution throughout the wall thickness and hence the load-bearing capacity of a thick-walled cylinder. Calculation of residual stresses after autofrettage process and optimization of autofrettage outline dimensions by using the amount of service pressures applied are common issues in literature.In this study, mandrel-cylinder tube interference dimensions were renovated by using traditional methods for swage autofrettage process of a gun barrel. Also, the residual stresses in the cylinder after autofrettage process, inside and outside material removal process and the variable service pressure throughout the cylinder applied were taken into consideration and incorporated into the design. By using the constrained optimization method, wall thickness(thus the weight) was optimized(minimized)to achieve the specified safety factor along the length of the cylinder. For the same cylinder, the results of the suggested analytical/with residual stress calculation approach were compared to analytical/without residual stress calculation results and numerical topology optimization method calculation results. Since the experimental measurement results are not yet available, it was not possible to compare them with the calculation results.The suggested approach enabled 22.9% extra weight reduction in proportion to numerical topology optimization and enabled 4.2% extra weight reduction in proportion to analytical/without residual stress optimization.Using this approach, the gain from residual stresses after autofrettage operation, the loss of residual stresses after material removal, and the effects of service pressures can be taken into account for each stage of design.

Decay of Pressure Fluctuation in the Hyporheic Zone around a Cylinder

Erosion around a submerged cylinder is a well-studied problem, and is of particular interest in bridge pier scour applications. Particles erode when lift and drag forces overcome a critical threshold. These forces are typically studied from above the water-riverbed interface and are related to geometry and surficial processes. The present study maps hyporheic pressure fluctuations as they are related to surface water velocity fluctuations. Relatively, high-pressure events in the subsurface promote a destabilizing force from within the riverbed and increase the potential for the mobilization of sediment. Differential pressure transducers were fitted within a vertical cylinder in a movable bed flume. The pressure ports were flush with the cylinder surface and below the water-sand interface. The three-orthogonal components of velocity were recorded synchronously with differential pressure measured over a 15 mm depth. As expected, results show decay in pressure fluctuations as a function of depth.

Analysis on Static Pressure Bearing Seal Characteristics of Guide Sleeve of Electro-hydraulic Servo Cylinder

As a typical bionic walking robot, hydraulic quadruped robot has attracted much attention because of its high mobility, strong load capacity and steady motion. The electro-hydraulic servo cylinder, as its power actuator, requires low friction, good lateral load resistance and high speed motion. The electro-hydraulic servo cylinder hydrostatic bearing seal guide sleeve is taken as the research object in this paper. By using Fluent software to analyze and contrast the film characteristics of rectangular and I-shaped oil chamber of hydrostatic bearing seal guide sleeve, the relationship between piston rod moving speed, eccentricity, oil film carrying capacity, friction force and leakage volume, as well as the relationship between oil feed flow and oil film bearing capacity, friction force, inlet pressure and leakage volume were analyzed. This study provides a theoretical basis for optimizing the static pressure bearing seal parameters.

INFLUENCE OF THREAD PITCH ON LOAD DISTRIBUTION ON THREADED END OF PRESSURE CYLINDER

One of the design methods for closing the end of a pressure cylinder is to screw down a screw plug on the threaded end of the cylinder. In this case, there is the problem of stress concentration in the threaded end of the pressure cylinder. To solve the problem, it is necessary to know accurately the load distribution on the threaded end of the cylinder. To find the load distribution on the threaded end of the pressure cylinder engaged with the screw plug, the following experiments are carried out. Applying the tensile load between the screw plug and the pressure cylinder and regarding the situation above as equivalent to the situation in which the internal pressure is applied, the load distribution is measured with the strain gauge. The influence of thread pitch on the load distribution on the threaded end of the cylinder is presented and an optimum pitch for design is discussed.

Evaluation of Inner Soil Pressure Acting on Opened Bottom Cylindrical Structure

An opened bottom cylinder is a large-diameter cylinder placed on a rubber base or embedded in a soil foundation. The settlement of such a cylinder differs greatly from that of a closed bottom cylinder and so does the distribution of inner soil pressure over the opened bottom cylindrical structure. Through investigation of the settlement and the inner soil pressure on the opened bottom cylinder by model experiments, the interactions among the filler inside the cylinder, subsoil and cylinder are analyzed. The adjusting mechanism of friction resistance between the inner filler and the wall of the cylinder during overturning of the cylinder is discussed. Based on the experimental study, a method for calculating the inner soil pressure on the cylindrical structure under axisymmetric loading or non- axisymmetric (with lateral) loading is proposed in this paper. Meanwhile, the effective anti-overturning ratio of the opened bottom cylinder is derived.

Dynamic Wave Pressures on Deeply Embedded Large Cylindrical Structures due to Random Waves

The response of dynamic wave pressures on structures would be more complicated and bring about new phenomena under the dynamic interaction between soil and structure. In order to better understand the response characteristics on deeply embedded large cylindrical structures under random waves, and accordingly to offer valuable findings for engineering, the authors designed wave flume experiments to investigate comparatively dynamic wave pressures on a single and on continuous cylinders with two different embedment depths in response to two wave spectra.The time histories of the water surface elevation and the corresponding dynamic wave pressures exerted on the cylinder were analyzed in the frequency domain. By calculating the transfer function and spectral density for dynamic wave pressures along the height and around the circumference of the cylinder, experimental results of the single cylinder were compared with the theoretical results based on the linear diffraction theory, and detailed comparisons were also carried out between the single and continuous cylinders. Some new findings and the corresponding analysis are reported in present paper. The investigation on continuous cylinders will be used in particular for reference in engineering applications because information is scarce on studying such kind of problem both analytically and experimentally.