A Residual Frequency Offset Estimation Method Based on Range Migration Fitting

Recently,researchers have proposed an emitter localization method based on passive synthetic aperture.However,the unknown residual frequency offset(RFO)between the transmit-ter and the receiver causes the received Doppler signal to shift,which affects the localization accu-racy.To solve this issue,this paper proposes a RFO estimation method based on range migration fitting.Due to the high frequency modulation slope of the linear frequency modulation(LFM)-mod-ulation radar signal,it is not affected by RFO in range compression.Therefore,the azimuth time can be estimated by fitting the peak value position of the pulse compression in range direction.Then,the matched filters are designed under different RFOs.When the zero-Doppler time obtained by the matched filters is consistent with the estimated azimuth time,the given RFO is the real RFO between the transceivers.The simulation results show that the estimation error of azimuth distance does not exceed 20 m when the received signal duration is not less than 3 s,the pulse repe-tition frequency(PRF)of the transmitter radar signal is not less than 1 kHz,the range detection is not larger than 1000 km,and the signal noise ratio(SNR)is not less than-5 dB.

A Robust Indoor Localization Algorithm Based on Polynomial Fitting and Gaussian Mixed Model

Wireless sensor network(WSN)positioning has a good effect on indoor positioning,so it has received extensive attention in the field of positioning.Non-line-of sight(NLOS)is a primary challenge in indoor complex environment.In this paper,a robust localization algorithm based on Gaussian mixture model and fitting polynomial is proposed to solve the problem of NLOS error.Firstly,fitting polynomials are used to predict the measured values.The residuals of predicted and measured values are clustered by Gaussian mixture model(GMM).The LOS probability and NLOS probability are calculated according to the clustering centers.The measured values are filtered by Kalman filter(KF),variable parameter unscented Kalman filter(VPUKF)and variable parameter particle filter(VPPF)in turn.The distance value processed by KF and VPUKF and the distance value processed by KF,VPUKF and VPPF are combined according to probability.Finally,the maximum likelihood method is used to calculate the position coordinate estimation.Through simulation comparison,the proposed algorithm has better positioning accuracy than several comparison algorithms in this paper.And it shows strong robustness in strong NLOS environment.

Comparative Analysis of Equal and Unequal Grounding Grid Configurations by Compression Ratio and Least Square Curve Fitting Techniques

The primary aim of the power system grounding is to safeguard the person and satisfying the performance of the power systemtomaintain reliable operation.With equal conductor spacing grounding grid design,the distribution of the current in the grid is not uniform.Hence,unequal grid conductor span in which grid conductors are concentrated more at the periphery is safer to practice than equal spacing.This paper presents the comparative analysis of two novel techniques that create unequal spacing among the grid conductors:the least-square curve fitting technique and the compression ratio techniquewith equal grid configuration for both square and rectangular grids.Particle Swarm Optimization(PSO)is adopted for finding out one optimal feasible solution among many feasible solutions of equal grid configuration for both square and rectangular grids.Comparative analysis is also carried out between square and rectangular grids using the least square curve fitting technique as it results in only one unequal grid configuration.Simulation results are obtained by theMATLAB software developed.Percentage of improvement in ground potential rise,step voltage,touch voltage,and grid resistancewith variation in compression ratios are plotted.

Application of Flipped Classroom Teaching Model Based on Micro-Course in Practical Training Teaching of Contact Lens Fitting Technology

Objective:This paper aims to study the application of flipped classroom teaching model based on micro-course in the practical training teaching of contact lens fitting technology.Methods:From September 21 to July 23,120 students majoring in ophthalmology and optometry were selected and randomly divided into groups.The control group adopted the traditional teaching mode,and the study group adopted the flipped classroom teaching mode based on micro-course.Teaching scores and the skills,observation and judgment,adaptability,and communication skills were compared between the groups.Results:Statistical comparison of teaching scores under different management methods showed that the clinical thinking score and practice work quality in the study group were higher than those of the control group,and the effect of the study group was better(P<0.05).The overall scores of skills,observation and judgment,adaptability,and communication skills of the study group were better than those in the control group,and the comprehensive ability scores in the two groups were significantly different(P<0.05).Conclusion:In practical training teaching of contact lens fitting technology,the application of flipped classroom teaching based on micro-course can improve the skill scores of personnel,and the overall effect is good.This can lay the foundation for advanced ophthalmology and optometry talents with profound theoretical knowledge and professional skills.

基于Vector Fitting的光伏并网逆变器控制器参数频域辨识方法

光伏并网逆变器通常含有内外环、锁相环等不同带宽控制环节,且控制器参数往往并不可知,即存在“灰箱”问题。为准确辨识不同带宽控制器参数,提出一种基于端口导纳特性的光伏并网逆变器控制器参数频域辨识方法。首先,建立典型控制下光伏并网逆变器交流端口的dq理论导纳模型,得到其理论导纳标准式;然后,通过扫频手段获得光伏并网逆变器交流端口的测量导纳数据,并采用Vector Fitting算法对测量的端口导纳数据进行矢量拟合,得到拟合导纳标准式;最后,运用最小二乘原理使理论导纳标准式与拟合导纳标准式对应项系数差值的平方和最小,从而辨识得到光伏并网逆变器控制器参数的估计值。参数辨识实例表明,所提方法能够同时准确辨识出不同带宽控制器参数。

Prosthetic modeling for femoral head based on ellipsoid fitting

A novel modeling method which can restore the shape of the femoral head with collapse induced by ischemic necrosis is proposed. First, sequential tomograms of the hip are obtained from a CT scan; secondly, an accurate and automatic method is used to extract the profile of the acetabulum; thirdly, a hybrid method is utilized to gather fiducial marks on the acetabulum; fourthly, bulky error sampling points are removed. Finally, an ellipsoid fitting method is used to fit the ellipsoid model of the femoral head. Two male sufferers with different necrosis extents are chosen as experimental subjects for contrastive simulation. Fifty cases of different ages （from 25 to 79 years old） are utilized for statistical comparisons of matching errors. The prosthetic models highly resemble the primary shape of the femoral head in health. This new method provides not only a theoretical model for accurate operation position fixing in an orthopaedics clinic, but it is also an innovative practical means for the individual manufacture of artificial femoral heads.

FITTING CORRECTION METHOD OF RING ARTIFACTS FOR RECONSTRUCTING CONE-BEAM CT IMAGES

In high-resolution cone-beam computed tomography （CBCT） using the flat-panel detector, imperfect or defect detector elements cause ring artifacts due to the none-uniformity of their X-ray response. They often disturb the image quality. A dedicated fitting correction method for high-resolution micro-CT is presented. The method converts each elementary X-ray response curve to an average one, and eliminates response inconsistency among pixels. Other factors of the method are discussed, such as the correction factor variability by different sampling frames and nonlinear factors over the whole spectrum. Results show that the noise and artifacts are both reduced in reconstructed images

The numerical simulation and inversion fitting of radon concentration distribution in homogeneous overburden above active fault zones

Based on the convection and diffusion mechanisms of radon migration, in this paper we deduce the two-dimensional differential equation for radon transportation in the overburden above active fault zones with an unlimited extension along the strike. Making use of the finite difference method, the radon concentration distribution in the overburden above active faults is calculated and modeled. The active fault zone parameters, such as the depth and the width of the fault zone, and the value of radon concentration, can be inverted from the measured radon concentration curve. These realize quantitative interpretation for radon concentration anomalies. The inversion results are in good agreement with the actual fault zone parameters.

Detection of Broad Bean Diseases by Fourier Transform Infrared Spectroscopy Combined with Curve Fitting

Fourier transform infrared （FTIR） spectroscopy was used to study diseased leaves in broad bean. Results showed that the infrared spectra of different broad bean diseased leaves were similar, which were mainly made up of the vibrational absorption bands of protein,lipid and polysaccharide.There were minor differences in-cluding the spectral peak position, peak shape and the absorption intensity in the range of 1 800-1 300 cm-1. There were obvious differences among their second derivative spectra in the range of 1 800-1 300 cm-1. After the procedure of the Fourier self-deconvolution and curve fitting of health bean leaves and broad bean diseased leaves in the range of 1 700-1 500 cm-1, three sub-peaks were obtained at 1 550 cm-1 （protein amide Ⅱ band）, 1 605 cm-1 （lignin） and 1 650 cm-1 （protein amide I band）.The ratios of relative areas of the bands of amide Ⅱ, lignin, and amide I were 38.86%, 28.68% and 32.47% in the spectra of healthy leaves, respec-tively. It was distinguished from the diseased leaves （chocolate spot leaf： 15.42%, 42.98% and 41.61%, ring spot leaf：32.39%, 35.63% and 31.98%, rust leaf： 13.97%, 46.40% and 39.65%, yel owing leaf curl disease leaf： 24.01%,36.55% and 39.44%）. For sub-peak area ratios （A1 563/A1 605, A1 650/A1 605 and A1 563/A1 654）, those of four kinds of diseased leaves were smal er than that of healthy leaves, and there were also differences among four kinds of diseased leaves. The results proved that FTIR combining with curve fitting might be a potential y useful tool for detecting different kinds of broad bean diseases.

Study on Growth and Development Rules and Growth Curve Fitting of Minghua Black Minks

Growth curves of Minghua black minks at 0-180 days old were fitted and analyzed by using two growth models Logistic and Gompertz. The results showed that the growth curves of Minghua black minks could be fitted very well by Logistic model and Gompertz model （the degree of fitting FF≥0.99）, but Gompertz model was better at fitting and predicting their weight.

Fitting集与根函数

群类理论是在有限可解群研究工作的基础上发展起来的,但近年来对有限群论的许多方面都起到越来越大的作用.Fitting类是重要群类之一.为了更深入地研究Fitting类,主要研究了Fitting集所具有的性质,用构造的方法证明了Fitting集与根函数之间可以建立一个一一对应的关系,证明了两个根函数的合成依然是根函数,并刻画了与该合成相关联的Fitting集,得到两个重要的定理.这对于Fitting类的研究具有重要意义.

关于有限可解群的Fitting子群的阶

得到有限可解群及其某些子群的阶与其Ｆｉｔｉｎｇ子群的阶之间的若干关系

Fitting子群是Abel群的有限可解群

本文证明了若有限的可解SD_2—群G的Fitting子群是Abel群,则G^(3)

Iterative circle fitting based on circular attracting factor

An intuitive method for circle fitting is proposed. Assuming an approximate circle(CA,n) for the fitting of some scattered points, it can be imagined that every point would apply a force to CA,n, which all together form an overall effect that "draws" CA,n towards best fitting to the group of points. The basic element of the force is called circular attracting factor(CAF) which is defined as a real scalar in a radial direction of CA,n. An iterative algorithm based on this idea is proposed, and the convergence and accuracy are analyzed. The algorithm converges uniformly which is proved by the analysis of Lyapunov function, and the accuracy of the algorithm is in accord with that of geometric least squares of circle fitting. The algorithm is adopted to circle detection in grayscale images, in which the transferring to binary images is not required, and thus the algorithm is less sensitive to lightening and background noise. The main point for the adaption is the calculation of CAF which is extended in radial directions of CA,n for the whole image. All pixels would apply forces to CA,n, and the overall effect of forces would be equivalent to a force from the centroid of pixels to CA,n. The forces from would-be edge pixels would overweigh that from noisy pixels, so the following approximate circle would be of better fitting. To reduce the amount of calculation, pixels are only used in an annular area including the boundary of CA,n just in between for the calculation of CAF. Examples are given, showing the process of circle fitting of scattered points around a circle from an initial assuming circle, comparing the fitting results for scattered points from some related literature, applying the method proposed for circular edge detection in grayscale images with noise, and/or with only partial arc of a circle, and for circle detection in BGA inspection.

Fitting长等于3的小群

设G是阶不超过50的有限群,且G的Fitting长等于3.本文给出了G的所有分类.

Arm-Root Curve Fitting Based on Body Surface Feature Points for Young Male

This paper is aiming to obtain an arm-root curve function performing the human arm-root size and shape realistically. A gypsum replica of upper arm for young male was made and scanned for extracting the 3D coordinates of 4 feature points of shoulder point, the anterior/posterior armpit point and the axillary point describing the real arm-root shape under the normalized definitions, and the 5 landmarks were confirmed additionally for improving the fitting precision. Then, the wholly and piecewise fitting of arm-root curve with 9 feature points and mark points in total were generated respectively based on least square polynomial fitting method. Comparing to the wholly fitting, the piecewise fitted function segmented by the line between anterior and posterior axillary points showed a high fitting degree of arm-root morphology with R-square of 1, the length difference between fitted curve and gypsum curve is 0.003 cm within error range. And it provided a basic curve model with standard feature points to simulate arm-root morphology realistically by curve fitting for accurate body measurement extraction.

在Fitting子群上不可裂的外－FA群

利用群的上同调中Ｌｙｎｄｏｎ－Ｈｅｅｂｓｃｈｉｅｄ。Ｓｅｒｒｅ谱序列的性质，论证了Ｆｉｔｔｉｎｇ子群上不可裂的外－ＦＡ群的存在性，并且给出了这类群的表出（Ｐｒａｓｅｎｔａｔｉｏｎｓｏｆｇｒｏｕｐｓ）。

Application of Virtual Fitting Technology and Impac on the Clothing Market

List the advantages of virtual fitting technology, summarize virtual insufficient in the development of present situation and the fitting technique of application examples. Analyze the influence of virtual fitting to the clothing market entity stores and clothing market e-commerce. According to the present situation of the virtual fitting, realize the sustainable ideas of the future direction of life.

基于用户Fitting的自行车车架结构参数化设计

基于用户Fitting的车架参数化系统设计,对车架结构进行分析,得出车架结构设计的参数及其约束,建立车架参数化模型;再结合人机工程学,得出与车架相关的人体关键尺寸参数和人与车架之间的人机约束关系,建立用户Fitting的参数化系统,整个系统是可视的,并且具有可控性,用户输入参数,系统就会自动驱动程序,生成符合其身体尺寸的车架模型及车架尺寸,为用户选择车架或装车Fitting时提供数据参考。

Seismic noise attenuation using nonstationary polynomial fitting

We propose a novel method for seismic noise attenuation by applying nonstationary polynomial fitting （NPF）, which can estimate coherent components with amplitude variation along the event. The NPF with time-varying coefficients can adaptively estimate the coherent components. The smoothness of the polynomial coefficients is controlled by shaping regularization. The signal is coherent along the offset axis in a common midpoint （CMP） gather after normal moveout （NMO）. We use NPF to estimate the effective signal and thereby to attenuate the random noise. For radial events-like noise such as ground roll, we first employ a radial trace （RT） transform to transform the data to the time-velocity domain. Then the NPF is used to estimate coherent noise in the RT domain. Finally, the coherent noise is adaptively subtracted from the noisy dataset. The proposed method can effectively estimate coherent noise with amplitude variations along the event and there is no need to propose that noise amplitude is constant. Results of synthetic and field data examples show that, compared with conventional methods such as stationary polynomial fitting and low cut filters, the proposed method can effectively suppress seismic noise and preserve the signals.