Analysis of reflected signal of quad rotor UAV based on model fitting in mobile communication system

In view of the many scenes of unmanned aerial vehicle(UAV)detection,a third-party signal source is used to design a receiver to monitor the UAV.It is of great significance to understand the reflection of the signal illuminating the UAV.Taking the communication base station(BS)signal as the third-party signal source,and considering the complete transmission link,reflection changes and loss fading of the communication signal,this study conducts model fitting for irregular UAV targets,simplifying complex targets into a combination of simple targets.Furthermore,the influence of the dielectric constant of the target surface and the signal irradiation angle on the signal reflection is analyzed.The analysis shows that the simulation results of this model fitting method are consistent with the results of other literature,which provides theoretical support for the detection of low and slow small targets such as UAVs.

Comparison of the Chapman-Richards Function with the Schnute Model in Stand growth

The Chapman-Richards Function and its two exception cases in applications were discussed and compared with the Schnute model in stand growth studies. Compared from all perspective, it was found that the Schnute model commonly used in foreitry was identical to the Chapman-Richards function. If some parameter in the Chapman-Richdrds Function was unconstraint, the function could also be very versatile to fit some exceptional growth curves, the fitted function should be identical to that the Schnute model.

Mathematical Modelling of the COVID-19 Epidemic in Northern Ireland in 2020

In this study, we investigate the dynamics of the COVID-19 epidemic in Northern Ireland from 1st March 2020 up to 25th December 2020, using several copies of a Susceptible-Exposed-Infectious-Recovered (SEIR) compartmental model, and compare it to a detailed publicly available dataset. We split the data into 10 time intervals and fit the models on the consecutive intervals to the cumulative number of confirmed positive cases on each interval. Using the fitted parameter estimates, we also provide estimates of the reproduction number. We also discuss the limitations and possible extensions of the employed model.

Laboratory investigation on damping characteristics of homogeneous and stratified soil-ash system

In this study,the damping responses of uniform soil,equi-proportional fly ash,and local soil as a single unit were investigated.The large-strain cyclic triaxial tests were performed for the specimen compacted at the desired density(95%e99%of maximum dry density).The compacted specimens were tested under the loading frequency of 0.3e1 Hz with medium confinement of 70e100 kPa.Also,the unsymmetrical behavior of the hysteresis loop was analyzed using three different damping estimation approaches,i.e.symmetric hysteresis loop(SHL),asymmetric hysteresis loop(ASHL),and the modified American Society for Testing and Materials(ASTM)method.The outcome of the study shows for fly ash,local soil,and layered soil-ash,the ASHL technique has the highest damping value,followed by ASTM and then the SHL approach.The specimens prepared under high density and subjected to high confinement show low damping values.However,the specimens tested at high frequency exhibits high damping behavior.Similarly,the damping value of fly ash determined using the SHL and ASHL methods has a similar profile and reaches a maximum at 1%shear strain value before decreasing.The composite stratified deposit exhibits more dependency on relative compaction,confining pressure,and less on loading frequency.Based on the results,it is highly recommended to use the ASHL approach,especially under large strain conditions irrespective of soil type.The maximum damping ratio of stratified deposits is always in between the damping ratio of local soil and fly ash.The damping ratio of stratified soil and local soil is slightly larger than that of the other soils,although the damping ratio of fly ash is equivalent to that of the sand and clayey soil.These results may be helpful in the accurate determination of the damping properties of the layered soil-ash system that is required in the seismic response analysis.

Highly Sensitive Ultrathin Flexible Thermoplastic Polyurethane/Carbon Black Fibrous Film Strain Sensor with Adjustable Scaffold Networks

In recently years,high-performance wearable strain sensors have attracted great attention in academic and industrial.Herein,a conductive polymer composite of electrospun thermoplastic polyurethane(TPU)fibrous film matrix-embedded carbon black(CB)particles with adjustable scaffold network was fabricated for high-sensitive strain sensor.This work indicated the influence of stereoscopic scaffold network structure built under various rotating speeds of collection device in electrospinning process on the electrical response of TPU/CB strain sensor.This structure makes the sensor exhibit combined characters of high sensitivity under stretching strain(gauge factor of 8962.7 at 155%strain),fast response time(60 ms),outstanding stability and durability(>10,000 cycles)and a widely workable stretching range(0–160%).This high-performance,wearable,flexible strain sensor has a broad vision of application such as intelligent terminals,electrical skins,voice measurement and human motion monitoring.Moreover,a theoretical approach was used to analyze mechanical property and a model based on tunneling theory was modified to describe the relative change of resistance upon the applied strain.Meanwhile,two equations based from this model were first proposed and offered an effective but simple approach to analyze the change of number of conductive paths and distance of adjacent conductive particles.

Automatic image segmentation method for cotton leaves with disease under natural environment

In order to improve the image segmentation performance of cotton leaves in natural environment, an automatic segmentation model of diseased leaf with active gradient and local information is proposed. Firstly, a segmented monotone decreasing edge composite function is proposed to accelerate the evolution of the level set curve in the gradient smooth region. Secondly, canny edge detection operator gradient is introduced into the model as the global information. In the process of the evolution of the level set function, the guidance information of the energy function is used to guide the curve evolution according to the local information of the image, and the smooth contour curve is obtained. And the main direction of the evolution of the level set curve is controlled according to the global gradient information, which effectively overcomes the local minima in the process of the evolution of the level set function. Finally, the Heaviside function is introduced into the energy function to smooth the contours of the motion and to increase the penalty function Φ(x) to calibrate the deviation of the level set function so that the level set is smooth and closed. The results showed that the model of cotton leaf edge profile curve could be obtained in the model of cotton leaf covered by bare soil, straw mulching and plastic film mulching, and the ideal edge of the ROI could be realized when the light was not uniform. In the complex background, the model can segment the leaves of the cotton with uneven illumination, shadow and weed background, and it is better to realize the ideal extraction of the edge of the blade. Compared with the Geodesic Active Contour(GAC) algorithm, Chan-Vese(C-V) algorithm and Local Binary Fitting(LBF) algorithm, it is found that the model has the advantages of segmentation accuracy and running time when processing seven kinds of cotton disease leaves images, including uneven lighting, leaf disease spot blur, adhesive diseased leaf, shadow, complex background, unclear diseased leaf edges, and staggered condition. This model can not only conduct image segmentation of cotton leaves under natural conditions, but also provide technical support for the accurate identification and diagnosis of cotton diseases.

Effects of dietary protein levels on the long-term growth response and fitting growth models of gibel carp(Carassius auratus gibelio)

A 41-wk growth trial was conducted to evaluate the effects of dietary protein levels on the long-term growth response and fitting growth models of gibel carp(Carassius auratus gibelio) with an initial body weight of 1.85 ± 0.17 g. The dietary protein levels were designed at 320(P32), 360(P36). 400(P40).and 440 g/kg(P44), respectively. The growth curves of the gibel carp for each group were fitted and analyzed with four nonlinear regression models(Gompertz. logistic. von Bertalanffy and Richards). The final body weights(mean ± SD) of the fish were 226 ± 6.231 ± 7.242 ± 2, and 236 ± 2 g for P32, P36, P40,and P44. respectively. Feed conversion ratio of P40 and P44 groups was significantly lower than that of P32 and P36 groups(P < 0.05). Productive protein value of P44 group was significantly lower than that of P32 and P36 groups, but not different from that of P40 group(P > 0.05). The growth response of the gibel carp for each group was the best fitted by Richards model with the lowest Chi^2, residual sum of squares and residual variance, then Gompertz and von Bertalanffy growth models, but the logistic model did not fit the data well justified by Chi^2 values. The optimal protein level(400 g/kg) prolonged the stage of fast growth and predicted the highest asymptotic weight, which was close to the harvest size in practice.

Optimization by Estimation of Distribution with DEUM Framework Based on Markov Random Fields

This paper presents a Markov random field （MRP） approach to estimating and sampling the probability distribution in populations of solutions. The approach is used to define a class of algorithms under the general heading distribution estimation using Markov random fields （DEUM）. DEUM is a subclass of estimation of distribution algorithms （EDAs） where interaction between solution variables is represented as an undirected graph and the joint probability of a solution is factorized as a Gibbs distribution derived from the structure of the graph. The focus of this paper will be on describing the three main characteristics of DEUM framework, which distinguishes it from the traditional EDA. They are： 1） use of MRF models, 2） fitness modeling approach to estimating the parameter of the model and 3） Monte Carlo approach to sampling from the model.

A derivation of the generalized Korf growth equation and its application

Based on the biological hypothesis of tree growth, the generalized Korf growth equation, was derived theoretically. From a standpoint of applications, the equation can be used in two ways associated with the power exponent ofp, and two types of growth equations: the Korf-A (p>1) and the Korf-B (O<p<1) were developed and between them, there is the Gompertz equation (p=1) to separate each other. All of the three types of equations are independent. It was concluded that the Korf-A equation could be used to describe the growth of trees, of which inflection point is between 0 andA/e, while the Korf-B equation with the inflection point betweenA/e andA could be applied to describe the biological population growth. It was found that the Korf-A equation had a better property in describing the growth process of a tree or a stand and its applications to predicting height growth and stand self-thinning showed general good fitness.

A Computer Software-Epitimulator~ for Simulating Temporal Dynamics of Plant Disease Epidemic Progress

The objective of the present study was to develop a computer software for simulating the temporal development of plant disease epidemics using Richards, logistic, Gompertz, monomolecular, and exponential functions, respectively, and for predicting disease with a fitted model. The software was programmed using Visual Basic （VB6.0） and packaged with the Wise Installation System. The Fibonacci （＇0.618＇） section strategy was used to find out the most appropriate value for the shape parameter （m） in Richards function simulation through looping procedures. The software program was repeatedly tested, debugged and edited until it was run through favorably and produced ideal outputs. It was named Epitimulator based on the phrase ＇epidemic time simulator＇ and has been registered by the National Copyright Department of China （Reg. no. 2007SR18489）. It can be installed and run on personal computers with all versions of Windows operational systems. Data of disease index and survey time are keyed in or imported from Access files. The output of fitted models and related data of parameters can be pasted into Microsoft Excel worksheet or into Word document for editing as required and the simulated disease progress curves can be stored in separate graphic files. After being finally tested and completed, Epitimulator was applied to simulate the epidemic progress of corn northern leaf blight （Exserohilum turcicum） with recorded data from field surveys of corn crops and the fitted models were output. Comparison of the simulation results showed that the disease progress was always best described by Richards function, which resulted in the most accurate simulation model. Result also showed that forecast of northern leaf blight development was highly accurate by using the computed progress model from Richards function.

Fixed-bed column study for deep removal of copper(Ⅱ) from simulated cobalt electrolyte using polystyrene-supported 2-aminomethylpyridine chelating resin

This study presents the deep removal of copper (Ⅱ) from the simulated cobalt electrolyte using fabricated polystyrene-supported 2-aminomethylpyridine chelating resin (PS-AMP) in a fixed-bed.The effects of bed height (7.0–14.0 cm),feed flow rate (4.5–9.0 mL/min),initial copper (Ⅱ) concentration of the feed (250–1000 mg/L),feed temperature (25–40 ℃) and the value of pH (2.0–4.0) on the adsorption process of the PS-AMP resin were investigated.The experimental data showed that the PS-AMP resin can deeply eliminate copper (Ⅱ) from the simulated cobalt electrolyte.The bed height,feed flow rate,initial copper (Ⅱ) concentration of the feed,feed temperature and feed pH value which corresponded to the highest removal of copper (Ⅱ) were 7.0 cm with 35 mm of the column diameter,4.5 mL/min,40℃,1000 mg/L and 4.0,respectively.The breakthrough capacity,the saturated capacity of the column and the mass ratio of Cu/Co (g/g) in the saturated resin were correspondingly 16.51 mg/g dry resin,61.72 mg/g dry resin and 37.67 under the optimal experimental conditions.The copper (Ⅱ) breakthrough curves were fitted by the empirical models of Thomas,Yoon-Nelson and Adam-Bohart,respectively.The Thomas model was found to be the most suitable one for predicting how the concentration of copper (Ⅱ) in the effluent changes with the adsorption time.

Gaussian process assisted coevolutionary estimation of distribution algorithm for computationally expensive problems

In order to reduce the computation of complex problems, a new surrogate-assisted estimation of distribution algorithm with Gaussian process was proposed. Coevolution was used in dual populations which evolved in parallel. The search space was projected into multiple subspaces and searched by sub-populations. Also, the whole space was exploited by the other population which exchanges information with the sub-populations. In order to make the evolutionary course efficient, multivariate Gaussian model and Gaussian mixture model were used in both populations separately to estimate the distribution of individuals and reproduce new generations. For the surrogate model, Gaussian process was combined with the algorithm which predicted variance of the predictions. The results on six benchmark functions show that the new algorithm performs better than other surrogate-model based algorithms and the computation complexity is only 10% of the original estimation of distribution algorithm.

A CONSTRAINED LEAST SQUARES FITTING TECHNIQUE FOR ARMA MODELING

Several ARMA modeling approaches are addressed. In these methods only part of a correlation sequence is employed for estimating parameters. It is satisfying, if the given correlation sequence is of real ARMA, since an ARMA process can be completely determined by part of its correlation se -quence. But for the case of a measured correlation sequence the whole sequence may be used to reduce the effect of error on model parameter estimation. In addition, these methods now do not guarantee a nonnegative spectral estimate. In view of the above-mentioned fact, a constrained least squares fitting technique is proposed which utilizes the whole measured correlation sequence and guarantees a nonnegative spectral estimate.

Estimating the Level of Asymptomatic COVID-19 Infections in Northern Ireland in 2020

The identification and understanding of COVID-19 potential routes of transmission are fundamental to informing policies and strategies to successfully control the outbreak. Various studies highlighted asymptomatic infections as one of the silent drivers of the epidemic. An accurate estimation of the asymptomatic cases and the understanding of their contribution to the spread of the disease could enhance the effectiveness of current control strategies, mainly based on the symptom onset, to curb transmission. We investigate the dynamics of the COVID-19 epidemic in Northern Ireland during the period 1st March 25th to December 2020 to estimate the proportion of the asymptomatic infections in the country. We extended our previous model to include the stage of the asymptomatic infection, and we implement the corresponding deterministic model using a publicly available dataset. We partition the data into 11 sets over the period of study and fit the model parameters on the consecutive intervals using the cumulative number of confirmed positive cases for each interval. Moreover, we assess numerically the impacts of uncertainty in testing and we provide estimates of the reproduction numbers using the fitted parameters. We found that the proportion of asymptomatically infectious subpopulations, in Northern Ireland during the period of study, ranged between 5% and 25% of exposed individuals. Also, the estimate of the basic reproduction number, R0, is 3.3089. The lower and upper estimates for herd immunity are (0.6181, 0.7243) suggesting that around 70% of the population of Northern Ireland should acquire immunity via infection or vaccination, which is in line with estimates reported in other studies.

Decoupled deep hough voting for point cloud registration

Estimating rigid transformation using noisy correspondences is critical to feature-based point cloud registration.Recently,a series of studies have attempted to combine traditional robust model fitting with deep learning.Among them,DHVR proposed a hough voting-based method,achieving new state-of-the-art performance.However,we find voting on rotation and translation simultaneously hinders achieving better performance.Therefore,we proposed a new hough voting-based method,which decouples rotation and translation space.Specifically,we first utilize hough voting and a neural network to estimate rotation.Then based on good initialization on rotation,we can easily obtain accurate rigid transformation.Extensive experiments on 3DMatch and 3DLoMatch datasets show that our method achieves comparable performances over the state-of-the-art methods.We further demonstrate the generalization of our method by experimenting on KITTI dataset.

Applications of structural equation modeling(SEM)in ecological studies:an updated review

Aims:This review was developed to introduce the essential components and variants of structural equation modeling(SEM),synthesize the common issues in SEM applications,and share our views on SEM’s future in ecological research.Methods:We searched the Web of Science on SEM applications in ecological studies from 1999 through 2016 and summarized the potential of SEMs,with a special focus on unexplored uses in ecology.We also analyzed and discussed the common issues with SEM applications in previous publications and presented our view for its future applications.Results:We searched and found 146 relevant publications on SEM applications in ecological studies.We found that five SEM variants had not commenly been applied in ecology,including the latent growth curve model,Bayesian SEM,partial least square SEM,hierarchical SEM,and variable/model selection.We identified ten common issues in SEM applications including strength of causal assumption,specification of feedback loops,selection of models and variables,identification of models,methods of estimation,explanation of latent variables,selection of fit indices,report of results,estimation of sample size,and the fit of model.Conclusions:In previous ecological studies,measurements of latent variables,explanations of model parameters,and reports of key statistics were commonly overlooked,while several advanced uses of SEM had been ignored overall.With the increasing availability of data,the use of SEM holds immense potential for ecologists in the future.

A case study of development and application of a streamlined control and response modeling system for PM_(2.5)attainment assessment in China

This article describes the development and application of a streamlined air control and response modeling system with a novel response surface modeling-linear coupled fitting method and a new module to provide streamlined model data for PM_（2.5） attainment assessment in China.This method is capable of significantly reducing the dimensions required to establish a response surface model,as well as capturing more realistic response of PM_（2.5） to emission changes with a limited number of model simulations.The newly developed module establishes a data link between the system and the Software for Model Attainment Test—Community Edition（SMAT-CE）,and has the ability to rapidly provide model responses to emission control scenarios for SMAT-CE using a simple interface.The performance of this streamlined system is demonstrated through a case study of the Yangtze River Delta（YRD） in China.Our results show that this system is capable of reproducing the Community Multi-Scale Air Quality（CMAQ） model simulation results with maximum mean normalized error 〈 3.5%.It is also demonstrated that primary emissions make a major contribution to ambient levels of PM_（2.5） in January and August（e.g.,more than50%contributed by primary emissions in Shanghai）,and Shanghai needs to have regional emission control both locally and in its neighboring provinces to meet China＇s annual PM_（2.5）National Ambient Air Quality Standard.The streamlined system provides a real-time control/response assessment to identify the contributions of major emission sources to ambient PM_（2.5）（and potentially O_3 as well） and streamline air quality data for SMAT-CE to perform attainment assessments.

A mathematical model for the dynamics and control of malaria in Nigeria

Malaria is a life-threatening disease endemic in many African countries especially Nigeria.A mathematical model is used to study the dynamics of malaria in Nigeria.The model incorporates drug resistance,treatment,and the use of mosquito nets as preventive strategies.By fitting the model to data on the incidence of malaria in Nigeria,important parameters associated with the disease dynamics are estimated.Using these estimated parameters,the basic reproduction number is calculated,future dynamics simulated,and those parameters with a large impact on Nigerian malaria determined.Overall,the results indicate that the disease is likely to remain endemic in Nigeria unless better control measures are focused on the dominant resistant strain,treatment is improved and the use of mosquito nets become widespread.

Preliminarily modeling of creep effect in electro-dynamic loudspeaker suspensions

The creep effect of suspensions in electro-dynamic loudspeakers was modeled based on fractional order derivatives.The fractional standard linear solid（FSLS） model was presented by substituting the Abel dashpot for Newton dashpot in Standard Linear Solid（SLS） model.The electrical impedance as well as the transfer function between diaphragm displacement and input voltage of the two tested midrange loudspeakers was measured by Klippel laser analyzer system,and the model parameters were identified by the least-mean-square method.By comparing the fitting results of FSLS model with the other two classical models- 4 Parameter Logarithmic model and SLS model,the results show that the FSLS model can rightly predict the frequency dependent compliance loss factor and yield higher accuracy for modeling the creep effect in loudspeaker suspensions.

A modified gas flow model in the near wellbore region below dew point pressure

When pressure in gas reservoirs fall below the dew point,condensate banking occurs around the wellbore which alters the fluid flow behavior.The state of the knowledge on this flow behavior is yet not fully-developed;which leads to severe problems in field.In this study,the Al-Hussainy,Ramey,and Crawford Solution Technique has been modified to accurately resemble the real gas flow behavior for this condition.First,a primary investigation was conducted to observe the severity of the problem in three condensate banked reservoirs.Then this study involved Constant Composition Expansion tests for determining the dew point,Prode Properties software for modeling the reservoir fluid properties,Flowing Material Balance(or Dynamic P/Z Material Balance)for identifying the pressure distribution of the selected reservoirs.The real field data along with the determined(analytical,computational,and experimental)data were incorporated to check the validity of the models.The modification proposes a Dimensionless Correction Factor(CD)for any condensate banked reservoir and identifies parameters such as the Perforation Factor(Pf)and Heterogeneity Factor(n).It is found that the Modified Al-Hussainy,Ramey,and Crawford Solution Technique successfully models the actual flow characteristics of the stated condition.