A Novel Disturbance Observer Based Fixed-Time Sliding Mode Control for Robotic Manipulators With Global Fast Convergence

This paper proposes a new global fixed-time sliding mode control strategy for the trajectory tracking control of uncertain robotic manipulators.First,a fixed-time disturbance observer(FTDO) is designed to deal with the adverse effects of model uncertainties and external disturbances in the manipulator systems.Then an adaptive scheme is used and the adaptive FTDO(AFTDO) is developed,so that the priori knowledge of the lumped disturbance is not required.Further,a new non-singular fast terminal sliding mode(NFTSM) surface is designed by using an arctan function,which helps to overcome the singularity problem and enhance the robustness of the system.Based on the estimation of the lumped disturbance by the AFTDO,a fixed-time non-singular fast terminal sliding mode controller(FTNFTSMC)is developed to guarantee the trajectory tracking errors converge to zero within a fixed time.The settling time is independent of the initial state of the system.In addition,the stability of the AFTDO and FTNFTSMC is strictly proved by using Lyapunov method.Finally,the fixed-time NFESM(FTNFTSM) algorithm is validated on a 2-link manipulator and comparisons with other existing sliding mode controllers(SMCs) are performed.The comparative results confirm that the FTNFTSMC has superior control performance.

Systematic Elastostatic Stiffness Model of Over-Constrained Parallel Manipulators Without Additional Constraint Equations

The establishment of an elastostatic stiffness model for over constrained parallel manipulators(PMs),particularly those with over constrained subclosed loops,poses a challenge while ensuring numerical stability.This study addresses this issue by proposing a systematic elastostatic stiffness model based on matrix structural analysis(MSA)and independent displacement coordinates(IDCs)extraction techniques.To begin,the closed-loop PM is transformed into an open-loop PM by eliminating constraints.A subassembly element is then introduced,which considers the flexibility of both rods and joints.This approach helps circumvent the numerical instability typically encountered with traditional constraint equations.The IDCs and analytical constraint equations of nodes constrained by various joints are summarized in the appendix,utilizing multipoint constraint theory and singularity analysis,all unified within a single coordinate frame.Subsequently,the open-loop mechanism is efficiently closed by referencing the constraint equations presented in the appendix,alongside its elastostatic model.The proposed method proves to be both modeling and computationally efficient due to the comprehensive summary of the constraint equations in the Appendix,eliminating the need for additional equations.An example utilizing an over constrained subclosed loops demonstrate the application of the proposed method.In conclusion,the model proposed in this study enriches the theory of elastostatic stiffness modeling of PMs and provides an effective solution for stiffness modeling challenges they present.

Manipulator tracking technology based on FSRUKF

Aiming at the shortcoming that the traditional industrial manipulator using off-line programming cannot change along with the change of external environment,the key technologies such as machine vision and manipulator control are studied,and a complete manipulator vision tracking system is designed.Firstly,Denavit-Hartenberg(D-H)parameters method is used to construct the model of the manipulator and analyze the forward and inverse kinematics equations of the manipulator.At the same time,a binocular camera is used to obtain the threedimensional position of the target.Secondly,in order to make the manipulator track the target more accurately,the fuzzy adaptive square root unscented Kalman filter(FSRUKF)is proposed to estimate the target state.Finally,the manipulator tracking system is built by using the position-based visual servo.The simulation experiments show that FSRUKF converges faster and with less error than the square root unscented Kalman filter(SRUKF),which meets the application requirements of the manipulator tracking system,and basically meets the application requirements of the manipulator tracking system in the practical experiments.

Kinematic,Workspace and Force Analysis of A Five-DOF Hybrid Manipulator R(2RPR)R/SP+RR

In the present study,the over-constrained hybrid manipulator R(2RPR)R/SP+RR is considered as the research objective.In this paper,kinematics of the hybrid manipulator,including the forward and inverse position,are analyzed.Then,the workspace is checked based on the inverse position solution to evaluate whether the workspace of the hybrid manipulator meets the requirements,and the actual workspace of the hybrid robot is analyzed.After that,the force analysis of the over-constrained parallel mechanism is carried out,and an ADAMS-ANSYS rigid-flexible hybrid body model is established to verify the simulation.Based on the obtained results from the force analysis,the manipulator structure is designed.Then,the structure optimization is carried out to improve the robot stiffness.Finally,calibration and workspace verification experiments are performed on the prototype,cutting experiment of an S-shaped aluminum alloy workpiece is completed,and the experiment verifies the machining ability of the prototype.This work conducts kinematics,workspace,force analyses,structural optimization design and experiments on the over-constrained hybrid manipulator R(2RPR)R/SP+RR,providing design basis and technical support for the development of the novel hybrid manipulator in practical engineering.

Neural Dynamics for Cooperative Motion Control of Omnidirectional Mobile Manipulators in the Presence of Noises: A Distributed Approach

This paper presents a distributed scheme with limited communications, aiming to achieve cooperative motion control for multiple omnidirectional mobile manipulators(MOMMs).The proposed scheme extends the existing single-agent motion control to cater to scenarios involving the cooperative operation of MOMMs. Specifically, squeeze-free cooperative load transportation is achieved for the end-effectors of MOMMs by incorporating cooperative repetitive motion planning(CRMP), while guiding each individual to desired poses. Then, the distributed scheme is formulated as a time-varying quadratic programming(QP) and solved online utilizing a noise-tolerant zeroing neural network(NTZNN). Theoretical analysis shows that the NTZNN model converges globally to the optimal solution of QP in the presence of noise. Finally, the effectiveness of the control design is demonstrated by numerical simulations and physical platform experiments.

Many faces of neuronal activity manipulation in Drosophila

Animals exhibit complex responses to external and internal stimuli.The information is computed by interconnected neurons that express numerous ion channels,which modulate the neuronal membrane potential.How can neuronal activity orchestrate complex motor patterns or allow learning from previous experience?To answer such questions,we need the ability not only to record,but also to modulate neuronal activity in both space(e.g.,neuronal subsets)and time.

Vibration Reduction of Open-chain Flexible Manipulators by Optimizing Independent Motions of Branch Links

In order to suppress vibration in flexible manipulators, a new type of manipulator mechanism with controllable local degrees of freedom is proposed. This mechanism consists of a main chain and some branch links. The main chain is of a flexible open-chain configuration with an end-effector installed at its tip, and the rigid branch links are able to perform active movements. It is proved by kinematics and dynamic analysis that, the branch links bear no direct kinematic relation to the main chain, but their independent motions can strongly affect the dynamic behavior and performance of the flexible manipulator. Then comes a new idea of suppressing vibration, in which independent motions of the branch links are used to suppress the undesired vibration of the flexible main chain through dynamic coupling. On this basis, an optimal method for reducing vibration of flexible manipulators is proposed. Finally, the effectiveness of this method is verified by numerical simulations.

FUZZY ADAPTIVE CONTROL OF FLEXIBLE-LINK ROBOT MANIPULATOR

A fuzzy adaptive control method is proposed for a flexible robot manipulator. Due to the structure characteristics of the flexible manipulator, the vibration modes must be controlled to realize the high-precision tip position. The Lagrangian principle is utilized to model the dynamic function of the single-degree flexible manipulator incorporating the assumed modes method. Simulation results of the fuzzy adaptive control method in the location control and the trajectory tracking with different tip disturbances are presented and compared with the results of the classic PD control. It shows that the controller can obtain the stable and robust performance.

FUZZY COORDINATION AND FORCE/POSITION CONTROL OF ROBOTIC MANIPULATOR

It is crucial for implementing force/position control of robotic manipulator under the constraint of unknown environment to determine the force control and the position control directions. This paper presents an on line algorithm to real timely estimate the tangent and the normal vectors of the constraint surface based on the measured contact force under the consideration of frictional force. A fuzzy synthesis policy is proposed to coordinate the conflict between the compliant force control and the stiff position control. An experimental study on an AdeptThree, a SCARA type robotic manipulator, is conducted. The experimental results show that the policy presented in the paper is effective.

A Decentralized Autonomous Control on Highly Redundant Robot Manipulators

The control method of highly redundant robot manipulators is introduced. A decentralized autonomous control scheme is used to guide the movement of robot manipulators so that the work done by manipulators is minimized. The method of computing pseudoinverse which needs too many complicated calculation can be avoided. Then the calculation and control of robots are simplified. At the same time system robustness/fault tolerance is achieved.

ON HYBRID POSITION/FORCE COORDINATED LEARNING CONTROL OF MULTIPLE MANIPULATORS

In this paper, coordinated control of multiple robot manipulators holding a rigid object is discussed. In consideration of inaccuracy of the dynamic model of a multiple manipulator system, the error equations on object position and internal force are derived. Then a hybrid position/force coordinated learning control scheme is presented and its convergence is proved. The scheme can improve the system performance by modifying the control input of the system after each iterative learning. Simulation results of two planar robot manipulators holding an object show the effectiveness of this control scheme.

Impedance force control for position controlled robotic manipulators under the constraint of unknown environments

A force control strategy for position controlled robotic manipulators is presented. On line force feedback data are employed to estimate the local shape of the unknown constraint. The estimated vectors are used to generate the virtual reference trajectory for the target impedance model that is driven by the force error to produce command position. By following the command position trajectory the robotic manipulator can follow the unknown constraint surface while keeping an acceptable force error in a manner depicted by the target impedance model. Computer simulation on a 3 linked planar manipulator and experimental studies on an Adept 3, an SCARA type robotic manipulator, are conducted to verify the force tracking capability of the proposed control strategy.

Kinematics and Dynamics Hessian Matrices of Manipulators Based on Screw Theory

The complexity of the kinematics and dynamics of a manipulator makes it necessary to simplify the modeling process.However,the traditional representations cannot achieve this because of the absence of coordinate invariance.Therefore,the coordinate invariant method is an important research issue.First,the rigid-body acceleration,the time derivative of the twist,is proved to be a screw,and its physical meaning is explained.Based on the twist and the rigid-body acceleration,the acceleration of the end-effector is expressed as a linear-bilinear form,and the kinematics Hessian matrix of the manipulator（represented by Lie bracket）is deduced.Further,Newton-Euler＇s equation is rewritten as a linear-bilinear form,from which the dynamics Hessian matrix of a rigid body is obtained.The formulae and the dynamics Hessian matrix are proved to be coordinate invariant.Referring to the principle of virtual work,the dynamics Hessian matrix of the parallel manipulator is gotten and the detailed dynamic model is derived.An index of dynamical coupling based on dynamics Hessian matrix is presented.In the end,a foldable parallel manipulator is taken as an example to validate the deduced kinematics and dynamics formulae.The screw theory based method can simplify the kinematics and dynamics of a manipulator,also the corresponding dynamics Hessian matrix can be used to evaluate the dynamical coupling of a manipulator.

Geometric Approach for Kinematic Analysis of a Class of 2-DOF Rotational Parallel Manipulators

Euler angles are commonly used as the orientation representation of most two degrees of freedom（2-DOF） rotational parallel mechanisms（RPMs）,as a result,the coupling of two angle parameters leads to complexity of kinematic model of this family of mechanisms.While a simple analytical kinematic model with respect to those parameters representing the geometrical characteristics of the mechanism,is very helpful to improve the performance of RPMs.In this paper,a new geometric kinematic modeling approach based on the concept of instantaneous single-rotation-angle is proposed and used for the 2-DOF RPMs with symmetry in a homo-kinetic plane.To authors＇ knowledge,this is a new contribution to parallel mechanisms.By means of this method,the forwards kinematics of 2-DOF RPMs is derived in a simple way,and three cases i.e.4-4R mechanism（Omni-wrist III）,spherical five-bar one,and 3-RSR1-SS one demonstrate the validity of the proposed geometric method.In addition,a novel 2-DOF RPM architecture with virtual center-of-motion is presented by aid of the same method.The result provides a useful tool for simplifying the model and extending the application of the RPMs.

Singularity Analysis of a 3-RPS Parallel Manipulator Using Geometric Algebra

Singular configurations must be avoided in path planning and control of a parallel manipulator. However, most studies rarely focus on an overall singularity loci distribution of lower-mobility parallel mechanisms. Geometric algebra is employed in analysis of singularity of a 3-RPS parallel manipulator. Twist and wrench in screw theory are represented in geometric algebra. Linear dependency of twists and wrenches are described by outer product in geometric algebra. Reciprocity between twists and constraint wrenches are reflected by duality. To compute the positions of the three spherical joints of the 3-RPS parallel manipulator, Tilt-and-Torsion angles are used to describe the orientation of the moving platform. The outer product of twists and constraint wrenches is used as an index for closeness to singularity（ICS） of the 3-RPS parallel manipulator. An overall and thorough perspective of the singularity loci distribution of the 3-RPS parallel manipulator is disclosed, which is helpful to design, trajectory planning and control of this kind of parallel manipulator.

Collision Avoidance of Cooperative Dual Redundant Manipulators

Dual redundant manipulators are extremely useful for tasks in dangerous or space environments, but efficient and real time coordinated control is hard to achieve. Collision avoidance between two cooperative manipulators is vital to the successful applications of dual redundant manipulators. Although methods based on the distance function have been demonstrated simple and efficient, different collision avoidance points can usually produce completely different results and even failure. The paper discussed the choices of collision avoidance points and proposed a novel method for the choosing of those points. The method is testified by simulation results of two redundant planar manipulators.

Kinematic and Dynamic Analysis of a 3-■US Spatial Parallel Manipulator

Parallel Kinematic Machines(PKMs)are being widely used for precise applications to achieve complex motions and variable poses for the end effector tool.PKMs are found in medical,assembly and manufacturing industries where accuracy is necessary.It is often desired to have a compact and simple architecture for the robotic mechanism.In this paper,the kinematic and dynamic analysis of a novel 3-PRUS(P:prismatic joint,R:revolute joint,U:universal joint,S:spherical joint)parallel manipulator with a mobile platform having 6 Degree of Freedom(Do F)is explained.The kinematic equations for the proposed spatial parallel mechanism are formulated using the Modified Denavit-Hartenberg(DH)technique considering both active and passive joints.The kinematic equations are used to derive the Jacobian matrix of the mechanism to identify the singular points within the workspace.A Jacobian based sti ness analysis is done to understand the variations in sti ness for different poses of the mobile platform and further,it is used to decide trajectories for the end effector within the singularity free region.The analytical model of the robot dynamics is presented using the Euler-Lagrangian approach with Lagrangian multipliers to include the system constraints.The gravity and inertial forces of all links are considered in the mathematical model.The analytical results of the dynamic model are compared with ADAMS simulation results for a pre-defined trajectory of the end effector.

Dimensional Synthesis of a 3-DOF Parallel Manipulator with Full Circle Rotation

Parallel robots are widely used in the academic and industrial fields. In spite of the numerous achievements in the design and dimensional synthesis of the low-mobility parallel robots, few research efforts are directed towards the asymmetric 3-DOF parallel robots whose end-effector can realize 2 translational and 1 rotational（2T1R） motion. In order to develop a manipulator with the capability of full circle rotation to enlarge the workspace, a new 2T1 R parallel mechanism is proposed. The modeling approach and kinematic analysis of this proposed mechanism are investigated. Using the method of vector analysis, the inverse kinematic equations are established. This is followed by a vigorous proof that this mechanism attains an annular workspace through its circular rotation and 2 dimensional translations. Taking the first order perturbation of the kinematic equations, the error Jacobian matrix which represents the mapping relationship between the error sources of geometric parameters and the end-effector position errors is derived. With consideration of the constraint conditions of pressure angles and feasible workspace, the dimensional synthesis is conducted with a goal to minimize the global comprehensive performance index. The dimension parameters making the mechanism to have optimal error mapping and kinematic performance are obtained through the optimization algorithm. All these research achievements lay the foundation for the prototype building of such kind of parallel robots.

Flexible Bio-tensegrity Manipulator with Multi-degree of Freedom and Variable Structure

Conventional manipulators with rigid structures and sti ness actuators have poor flexibility,limited obstacle avoidance capability,and constrained workspace.Some developed flexible or soft manipulators in recent years have the characteristics of infinite degrees of freedom,high flexibility,environmental adaptability,and extended manipulation capability.However,these existing manipulators still cannot achieve the shrinking motion and independent control of specified segments like the animals,which hinders their applications.In this paper,a flexible bio-tensegrity manipulator,inspired by the longitudinal and transversal muscles of octopus tentacles,was proposed to mimic the shrinking behavior and achieve the variable motion patterns of each segment.Such proposed manipulator uses the elastic spring as the backbone,which is driven by four cables and has one variable structure mechanism in each segment to achieve the independent control of each segment.The variable structure mechanism innovatively contains seven lock-release states to independently control the bending and shrinking motion of each segment.After the kinematic modeling and analysis,one prototype of such bionic flexible manipulator was built and the open-loop control method was proposed.Some proof-of-concept experiments,including the shrinking motion,bending motion,and variable structure motion,were carried out by controlling the length of four cables and changing the lock-release states of the variable structure mechanism,which validate the feasibility and validity of our proposed prototype.Meanwhile,the experimental results show the flexible manipulator can accomplish the bending and shrinking motion with the relative error less than 6.8%through the simple independent control of each segment using the variable structure mechanism.This proposed manipulator has the features of controllable degree-of-freedom in each segment,which extend their environmental adaptability,and manipulation capability.

Trajectory Tracking of a Planer Parallel Manipulator by Using Computed Force Control Method

Despite small workspace, parallel manipulators have some advantages over their serial counterparts in terms of higher speed, acceleration, rigidity, accuracy, manufacturing cost and payload. Accordingly, this type of manipulators can be used in many applications such as in high-speed machine tools, tuning machine for feeding, sensitive cutting, assembly and packaging. This paper presents a special type of planar parallel manipulator with three degrees of freedom. It is constructed as a variable geometry truss generally known planar Stewart platform. The reachable and orientation workspaces are obtained for this manipulator. The inverse kinematic analysis is solved for the trajectory tracking according to the redundancy and joint limit avoidance. Then, the dynamics model of the manipulator is established by using Virtual Work method. The simulations are performed to follow the given planar trajectories by using the dynamic equations of the variable geometry truss manipulator and computed force control method. In computed force control method, the feedback gain matrices for PD control are tuned with fixed matrices by trail end error and variable ones by means of optimization with genetic algorithm.