Flat Steel Ribbon Wound Pressure Vessels (FSRWPVs) are used in many important industry areas. There is no such kind of pressure vessel exploding on operation for its reasonable structure design. Many explosion experim...Flat Steel Ribbon Wound Pressure Vessels (FSRWPVs) are used in many important industry areas. There is no such kind of pressure vessel exploding on operation for its reasonable structure design. Many explosion experiments on Flat Steel Ribbon Wound Pressure Vessel showed that their limited load pressure is related to the winding angle of the steel ribbons. FSRWPVs with reasonable winding angle have better security and lower cost. Reasonable angels given at the end of this paper facilitate engineering design.展开更多
By analyzing heat transfer on the wall of fiat steel ribbon wound vessel （FSRWV）, a numerical model of temperature distribution on the entire wall （including inner core wall, flat steel ribbons, outside cylinder of...By analyzing heat transfer on the wall of fiat steel ribbon wound vessel （FSRWV）, a numerical model of temperature distribution on the entire wall （including inner core wall, flat steel ribbons, outside cylinder of jacket and insulating layer） was established by the authors. With the model, the temperature distribution and the length change in the vessel walls and flat steel ribbons in low temperature are calculated and analyzed. The results show that the flat steel ribbon wound cryogenic high-pressure vessel is simpler in structure, safer and easier to manufacture than those of conventional ones.展开更多
In order to constitute engineering design methods of the flat ribbon wound explosion containment vessels, the dynamic response of such vessels subjected to internal explosion loading is simulated using LS-DYNA3D. Thre...In order to constitute engineering design methods of the flat ribbon wound explosion containment vessels, the dynamic response of such vessels subjected to internal explosion loading is simulated using LS-DYNA3D. Three winding angles, 10°, 15°and 20°, are considered. It is shown that among ribbon vessels investigated, the center displacement of outermost ribbons of the vessel with 10°winding angle is the smallest under the same blast loading. The response of vessels loaded in inner core is local. From the center of the cylindrical shell to the bottom cover, the maximum strain gradually decreases. The ribbons are subjected to tension in the length direction and compression in the width direction. Blasting shock energy concentrates on where is close to center section of blasting. For comparison, numerical simulation of a monobloc thick-walled explosion containment vessel is also investigated. It can be found that the biggest deformation of the flat ribbon wound explosion containment vessels is bigger than that of the monobloc thick-walled explosion containment vessel in the center section of blasting under the same TNT. Numerical results are approximately in agreement with experimental ones. It is proved that the ribbon vessels have the valuable properties of ' leak before burst at worst' compared with the monobloc vessels through numerical simulation.展开更多
文摘Flat Steel Ribbon Wound Pressure Vessels (FSRWPVs) are used in many important industry areas. There is no such kind of pressure vessel exploding on operation for its reasonable structure design. Many explosion experiments on Flat Steel Ribbon Wound Pressure Vessel showed that their limited load pressure is related to the winding angle of the steel ribbons. FSRWPVs with reasonable winding angle have better security and lower cost. Reasonable angels given at the end of this paper facilitate engineering design.
文摘By analyzing heat transfer on the wall of fiat steel ribbon wound vessel （FSRWV）, a numerical model of temperature distribution on the entire wall （including inner core wall, flat steel ribbons, outside cylinder of jacket and insulating layer） was established by the authors. With the model, the temperature distribution and the length change in the vessel walls and flat steel ribbons in low temperature are calculated and analyzed. The results show that the flat steel ribbon wound cryogenic high-pressure vessel is simpler in structure, safer and easier to manufacture than those of conventional ones.
基金Supported by National Natural Science Foundation of China(No. 10372091)
文摘In order to constitute engineering design methods of the flat ribbon wound explosion containment vessels, the dynamic response of such vessels subjected to internal explosion loading is simulated using LS-DYNA3D. Three winding angles, 10°, 15°and 20°, are considered. It is shown that among ribbon vessels investigated, the center displacement of outermost ribbons of the vessel with 10°winding angle is the smallest under the same blast loading. The response of vessels loaded in inner core is local. From the center of the cylindrical shell to the bottom cover, the maximum strain gradually decreases. The ribbons are subjected to tension in the length direction and compression in the width direction. Blasting shock energy concentrates on where is close to center section of blasting. For comparison, numerical simulation of a monobloc thick-walled explosion containment vessel is also investigated. It can be found that the biggest deformation of the flat ribbon wound explosion containment vessels is bigger than that of the monobloc thick-walled explosion containment vessel in the center section of blasting under the same TNT. Numerical results are approximately in agreement with experimental ones. It is proved that the ribbon vessels have the valuable properties of ' leak before burst at worst' compared with the monobloc vessels through numerical simulation.
