The stretch of blocks with rectangular section using flat anvils was simulated by using ANSYS software. The inner stress distribution for different tool width ratio w/h and blank width ratio b/h was studied. Consequen...The stretch of blocks with rectangular section using flat anvils was simulated by using ANSYS software. The inner stress distribution for different tool width ratio w/h and blank width ratio b/h was studied. Consequent- ly, critical anvil width ratio （w/h）c and critical blank width ratio （b/h）c are obtained, which provide a sound basis for designing reasonable stretching technology.展开更多
The choice of extrusion process is a decisive factor that affects the finished product quality for polybag manufacturing. One important component influencing the quality of the finished product is the selection of the...The choice of extrusion process is a decisive factor that affects the finished product quality for polybag manufacturing. One important component influencing the quality of the finished product is the selection of the extrusion technique. Two popular procedures that vary in the kind of dye used and the final product’s texture are cast film and blown film. In the horizontal extrusion moulding method known as “cast film”, heated resin is injected into a flat dye and allowed to cool on chill rolls. The film produced is clear, lightweight, and appropriate for lamination;its thickness varies based on the winding speed and the film is slower to crystallize and has less clarity but more durability because the resin molecules have reoriented, facing limitation of high wastage generation. This study primarily focused on the preparation of polybag film using the blown film extrusion process, utilizing high-quality polymer resins such as polyester polyethylene (PP) and linear low-density polyethylene (LLDPE) to minimize waste generation. The novelty of the process was reflected in minimising the waste generation. The control parameters considered in this study are temperature, pressure, and air intake volume. We investigated the influence of these critical process control parameters on the gauge thickness, optical properties, and mechanical strength of the polybag film produced through blown film extrusion. Additionally, we replicated the blown film process using simulation software developed at Pennsylvania College of Technology. The simulation results confirmed the overall stability of the polybag film produced through the blown film extrusion process.展开更多
Width spread is usually considered in hot rolling, nevertheless, it can be ignore in cold rolling. In order to control the crown and flatness better simultaneously and realize the decoupling of crown and flatness, the...Width spread is usually considered in hot rolling, nevertheless, it can be ignore in cold rolling. In order to control the crown and flatness better simultaneously and realize the decoupling of crown and flatness, the transverse displacement function of strip is defined and deduced. The factors that affects the width spread are analyzing with the function. According to the unchanged principle of volume before and after rolling, the flatness model which considers the width spread is deduced. Through the model, the transverse metal flowing of different stands and different thickness is analyzing, it is found that the width spread is biggest in cold rolling at the No. 1 stand because of the maximum thickness and reduction and the minimum deformation resistance. It gives a good foundation for the decoupling of crown and flatness.展开更多
基金ItemSponsored by Doctoral Foundation of Education Ministry of China (96021603)
文摘The stretch of blocks with rectangular section using flat anvils was simulated by using ANSYS software. The inner stress distribution for different tool width ratio w/h and blank width ratio b/h was studied. Consequent- ly, critical anvil width ratio （w/h）c and critical blank width ratio （b/h）c are obtained, which provide a sound basis for designing reasonable stretching technology.
文摘The choice of extrusion process is a decisive factor that affects the finished product quality for polybag manufacturing. One important component influencing the quality of the finished product is the selection of the extrusion technique. Two popular procedures that vary in the kind of dye used and the final product’s texture are cast film and blown film. In the horizontal extrusion moulding method known as “cast film”, heated resin is injected into a flat dye and allowed to cool on chill rolls. The film produced is clear, lightweight, and appropriate for lamination;its thickness varies based on the winding speed and the film is slower to crystallize and has less clarity but more durability because the resin molecules have reoriented, facing limitation of high wastage generation. This study primarily focused on the preparation of polybag film using the blown film extrusion process, utilizing high-quality polymer resins such as polyester polyethylene (PP) and linear low-density polyethylene (LLDPE) to minimize waste generation. The novelty of the process was reflected in minimising the waste generation. The control parameters considered in this study are temperature, pressure, and air intake volume. We investigated the influence of these critical process control parameters on the gauge thickness, optical properties, and mechanical strength of the polybag film produced through blown film extrusion. Additionally, we replicated the blown film process using simulation software developed at Pennsylvania College of Technology. The simulation results confirmed the overall stability of the polybag film produced through the blown film extrusion process.
基金Supported by Beijing Higher Education Young Elite Teacher Project(No.YETP0369)
文摘Width spread is usually considered in hot rolling, nevertheless, it can be ignore in cold rolling. In order to control the crown and flatness better simultaneously and realize the decoupling of crown and flatness, the transverse displacement function of strip is defined and deduced. The factors that affects the width spread are analyzing with the function. According to the unchanged principle of volume before and after rolling, the flatness model which considers the width spread is deduced. Through the model, the transverse metal flowing of different stands and different thickness is analyzing, it is found that the width spread is biggest in cold rolling at the No. 1 stand because of the maximum thickness and reduction and the minimum deformation resistance. It gives a good foundation for the decoupling of crown and flatness.
