A theoretical model for impact protection of flexible polymer material

The relationship between the protective performance of flexible polymer material and material parameters(elasticmodulus,viscosity coefficient)is explored,an impact collision motion equation between two bodies is establishedfrom the viscoelastic material constitutive,and the relationship between the kinematic response and the materialparameters is obtained.Based on the Kelvin constitutive model,a theoretical model for impact between the pro-tective body and the protected body is established,then the dynamic response is obtained.The feasibility of themodel was verified by drop hammer experiment,and the material parameters(elastic modulus,viscosity coeffi-cient)were obtained by formula.The model is discretized and the relationship between local impact response andmaterial parameters is analyzed.The discussion results on the relationship between the impact response and theprotective material performance indicate that adjusting the elastic modulus,viscosity coefficient,and thicknessof the protective material can effectively improve protective effect.

Experimental Investigation of a Phase-ChangeMaterial’s Stabilizing Role in a Pilot of Smart Salt-Gradient Solar Ponds

Faced with the world’s environmental and energy-related challenges,researchers are turning to innovative,sustainable and intelligent solutions to produce,store,and distribute energy.This work explores the trend of using a smart sensor to monitor the stability and efficiency of a salt-gradient solar pond.Several studies have been conducted to improve the thermal efficiency of salt-gradient solar ponds by introducing other materials.This study investigates the thermal and salinity behaviors of a pilot of smart salt-gradient solar ponds with(SGSP)and without(SGSPP)paraffin wax(PW)as a phase-change material(PCM).Temperature and salinity were measured experimentally using a smart sensor,with the measurements being used to investigate the stabilizing effects of placing the PCM in the solar pond’s lower convective zone.The experimental results show that the pond with the PCM(SGSPP)achieved greater thermal and salinity stability,with there being a lesser temperature and salinity gradient between the different layers when compared to a solar pond without thePCM(SGSP).The use of the PCM,therefore,helped control the maximum and minimum temperature of the pond’s storage zone.The UCZ has been found to operate approximately 4 degrees above the average ambient temperature of the day in the SGSPP and 7 degrees in SGSP.Moreover,an unstable situation is generated after 5 days from starting the operation and at 1.9 m from the bottom,and certain points have the tendency to be neutral from the upper depths in 1,3 m of the bottom.

Abrasion test of flexible protective materials on hydraulic structures

In this study, several kinds of flexible protective materials sprayed with polyurea elastomers （hereinafter referred to as polyurea elastomer protective material） were adopted to meet the abrasion resistance requirement of hydraulic structures, and their abrasion resistances against the water flow with suspended load or bed load were studied systematically through tests. Natural basalt stones were adopted as the abrasive for simulation of the abrasion effect of the water flow with bed load, and test results indicate that the basalt stone is suitable for use in the abrasion resistance test of the flexible protective material. The wear process of the polyurea elastomer protective material is stable, and the wear loss is linear with the time of abrasion. If the wear thickness is regarded as the abrasion resistance evaluation factor, the abrasion resistance of the 351 pure polyurea is about twice those of pure polyurea with a high level of hardness and aliphatic polyurea, and over five times that of high-performance abrasion-resistant concrete under the abrasion of the water flow with suspended load. It is also about 50 times that of high-performance abrasion-resistant concrete under the abrasion of the water flow with bed load. Overall, the abrasion resistance of pure polyurea presented a decreasing trend with increasing hardness. Pure polyurea with a Shore hardness of D30 has the best abrasion resistance, which is 60 to 70 times that of high-performance abrasion-resistant concrete under the abrasion of the water flow with bed load, and has been recommended, among the five kinds of pure polyurea materials with different hardness, in anti-abrasion protection of hydraulic structures.

Recent Advances in Design Strategies and Multifunctionality of Flexible Electromagnetic Interference Shielding Materials

With rapid development of 5G communication technologies,electromagnetic interference(EMI)shielding for electronic devices has become an urgent demand in recent years,where the development of corresponding EMI shielding materials against detrimental electromagnetic radiation plays an essential role.Meanwhile,the EMI shielding materials with high flexibility and functional integrity are highly demanded for emerging shielding applications.Hitherto,a variety of flexible EMI shielding materials with lightweight and multifunctionalities have been developed.In this review,we not only introduce the recent development of flexible EMI shielding materials,but also elaborate the EMI shielding mechanisms and the index for"green EMI shielding"performance.In addition,the construction strategies for sophisticated multifunctionalities of flexible shielding materials are summarized.Finally,we propose several possible research directions for flexible EMI shielding materials in near future,which could be inspirational to the fast-growing next-generation flexible electronic devices with reliable and multipurpose protections as offered by EMI shielding materials.

Flexible SERS substrates for hazardous materials detection: recent advances

This article reviews the most recent advances in the development of flexible substrates used as surface-enhanced Ra-man scattering(SERS)platforms for detecting several hazardous materials(e.g.,explosives,pesticides,drugs,and dyes).Different flexible platforms such as papers/filter papers,fabrics,polymer nanofibers,and cellulose fibers have been investigated over the last few years and their SERS efficacies have been evaluated.We start with an introduction of the importance of hazardous materials trace detection followed by a summary of different SERS methodologies with par-ticular attention on flexible substrates and their advantages over the nanostructures and nanoparticle-based solid/hybrid substrates.The potential of flexible SERS substrates,in conjunction with a simple portable Raman spectrometer,is the power to enable practical/on-field/point of interest applications primarily because of their low-cost and easy sampling.

Recent progress in 2D materials for flexible supercapacitors

High performance supercapacitors coupled with mechanical flexibility are needed to drive flexible and wearable electronics that have anesthetic appeal and multi-functionality. Two dimensional（2D） materials have attracted attention owing to their unique physicochemical and electrochemical properties, in addition to their ability to form hetero-structures with other nanomaterials further improving mechanical and electrochemical properties. After a brief introduction of supercapacitors and 2D materials, recent progress on flexible supercapacitors using 2D materials is reviewed. Here we provide insights into the structure–property relationships of flexible electrodes, in particular free-standing films. We also present our perspectives on the development of flexible supercapacitors.

Universal memory based on phase-change materials:From phase-change random access memory to optoelectronic hybrid storage

The era of information explosion is coming and information need to be continuously stored and randomly accessed over long-term periods,which constitute an insurmountable challenge for existing data centers.At present,computing devices use the von Neumann architecture with separate computing and memory units,which exposes the shortcomings of“memory bottleneck”.Nonvolatile memristor can realize data storage and in-memory computing at the same time and promises to overcome this bottleneck.Phase-change random access memory(PCRAM)is called one of the best solutions for next generation non-volatile memory.Due to its high speed,good data retention,high density,low power consumption,PCRAM has the broad commercial prospects in the in-memory computing application.In this review,the research progress of phase-change materials and device structures for PCRAM,as well as the most critical performances for a universal memory,such as speed,capacity,and power consumption,are reviewed.By comparing the advantages and disadvantages of phase-change optical disk and PCRAM,a new concept of optoelectronic hybrid storage based on phase-change material is proposed.Furthermore,its feasibility to replace existing memory technologies as a universal memory is also discussed as well.

Finite Element Simulation of Flexible Roll Forming with Supplemented Material Data and the Experimental Verification

Flexible roll forming is a promising manufacturing method for the production of variable cross section products. Considering the large plastic strain in this forming process which is much larger than that of uniform deformation phase of uniaxial tensile test, the widely adopted method of simulating the forming processes with non-supplemented material data from uniaxial tensile test will certainly lead to large error. To reduce this error, the material data is supplemented based on three constitutive models. Then a finite element model of a six passes flexible roll forming process is established based on the supplemented material data and the original material data from the uniaxial tensile test. The flexible roll forming experiment of a B pillar reinforcing plate is carried out to verify the proposed method. Final cross section shapes of the experimental and the simulated results are compared. It is shown that the simulation calculated with supplemented material data based on Swift model agrees well with the experimental results, while the simulation based on original material data could not predict the actual deformation accurately. The results indicate that this material supplement method is reliable and indispensible, and the simulation model can well reflect the real metal forming process. Detailed analysis of the distribution and history of plastic strain at different positions are performed. A new material data supplement method is proposed to tackle the problem which is ignored in other roll forming simulations, and thus the forming process simulation accuracy can be greatly improved.

Smart Material Based Complex Mode Active Control of Flexible Manipulators with Kinematic Redundancy

An active control methodology is presented for suppressing the vibratoryresponse of flexible redundant manipulators with bonded piezoceramic actuators and strain gagesensors. Firstly, the dynamic equation of the manipulator is decoupled by means of the complex modetheory and the state-space expression of the controlled system is developed. Secondly, a continuouslinear quadratic regulator (LQR) state feedback controller is designed based on the minimumprinciple. Thirdly, a full-order Luenberger state observer featuring an assigned degree of stabilityis determined via the duality between control and estimation. Finally, a numerical simulation iscarried out on a planar 3R flexible redundant manipulator. The simulation results reveal that thedynamic performance of the system is improved rapidly and significantly.

Paraffin/SiC as a Novel Composite Phase-Change Material for a Lithium-Ion Battery Thermal Management System

A lithium-ion battery thermal management system has always been a hot spot in the battery industry. In this study, a novel high-thermal-conductivity composite phase-change material(CPCM) made by paraffin wax and silicon was adopted to facilitate heat transfer. Moreover, high resistance or even insulation of CPCM is capable of preventing short circuits between the cells. The heat transfer mechanism of CPCMs was determined under a scanning electron microscope. A thermogravimetric analyzer was employed to determine the thermal stability. A diff erential scanning calorimeter was used to explore the thermophysical properties of the composite samples. By comparing the results of the experiment, it was reported that under the silicon carbide content of 5%, the parameters were better than others. The phase-change enthalpy of CPCM was 199.4 J/g, the leakage rate of liquid was 4.6%, and the melting point was 53.6℃. To verify the practicality of CPCM, a three-dimensional layered battery pack model was built in the COMSOL Multiphysics software. By simulating the thermal runaway inside the battery packs of various materials, it was reported that the addition of CPCM significantly narrowed the temperature range of the battery pack from 300–370 to 303–304 K. Therefore, CPCM can eff ectively increase the rate of heat transfer to prevent the chain of thermal runaway reactions. It also enables the battery pack to run at a stable temperature.

Flexible electronics and optoelectronics of 2D van der Waals materials

Flexible electronics and optoelectronics exhibit inevitable trends in next-generation intelligent industries,including healthcare and wellness,electronic skins,the automotive industry,and foldable or rollable displays.Traditional bulk-material-based flexible devices considerably rely on lattice-matched crystal structures and are usually plagued by unavoidable chemical disorders at the interface.Two-dimensional van der Waals materials(2D VdWMs)have exceptional multifunctional properties,including large specific area,dangling-bond-free interface,plane-to-plane van der Waals interactions,and excellent mechanical,electrical,and optical properties.Thus,2D VdWMs have considerable application potential in functional intelligent flexible devices.To utilize the unique properties of 2D VdWMs and their van der Waals heterostructures,new designs and configurations of electronics and optoelectronics have emerged.However,these new designs and configurations do not consider lattice mismatch and process incompatibility issues.In this review,we summarized the recently reported 2D VdWM-based flexible electronic and optoelectronic devices with various functions thoroughly.Moreover,we identified the challenges and opportunities for further applications of 2D VdWM-based flexible electronics and optoelectronics.

Design of broadband achromatic metasurface device based on phase-change material Ge_(2)Sb_(2)Te_(5)

Based on the phase-change material Ge_(2)Sb_(2)Te_(5)(GST),achromatic metasurface optical device in the longer-infrared wavelength is designed.With the combination of the linear phase gradient GST nanopillar and the adjustment of the crystalline fraction m value of GST,the polarization insensitive achromic metalenses and beam deflector metasurface within the longer-infrared wavelength 9.5μm to 13μm are realized.The design results show that the achromatic metalenses can be focused on the same focal plane within the working waveband.The simulation calculation results show that the fullwidth at half-maximum(FWHM)of the focusing spot reaches the diffraction limit at each wavelength.In addition,the same method is also used to design a broadband achromatic beam deflector metasurface with the same deflection angle of 19°.The method proposed in this article not only provides new ideas for the design of achromatic metasurfaces,but also provides new possibilities for the integration of optical imaging,optical coding and other related optical systems.

FEM simulation of flexible roll forming based on different material models

Flexible roll forming is a new roll forming process that produces parts with variable cross sections. This forming process is proposed to meet the demand of weight reduction of automobile industry. In order to study the mechanisms and material flow rules in this new forming process,the finite element mothod( FEM) model of a nine-step flexible roll forming of an ultra-high-strength steel bumper is established based on deep understanding and reasonable simplification of the process.Given that the material model is an important factor that influences the simulation accuracy,three material models which consist of different yield criteria and hardening models are adopted in the FEM models. Sheet thickness and springback amount calculated with three material models are studied comparatively. According to sheet thickness reduction and springback amounts,it is found that the MKi( Mises yield criterion and kinematic hardening law) model's result is larger than MI( Mises yield criterion and isotropic hardening law) model and HI( Hill's yield criterion and isotropic hardening law) model. Therefore,it is concluded that material models do have influences on the flexible roll forming simulation and need to be determined carefully.

An artificial synapse by superlattice-like phase-change material for low-power brain-inspired computing

Phase-change material(PCM)is generating widespread interest as a new candidate for artificial synapses in bioinspired computer systems.However,the amorphization process of PCM devices tends to be abrupt,unlike continuous synaptic depression.The relatively large power consumption and poor analog behavior of PCM devices greatly limit their applications.Here,we fabricate a GeTe/Sb2Te3 superlattice-like PCM device which allows a progressive RESET process.Our devices feature low-power consumption operation and potential high-density integration,which can effectively simulate biological synaptic characteristics.The programming energy can be further reduced by properly selecting the resistance range and operating method.The fabricated devices are implemented in both artificial neural networks(ANN)and convolutional neural network(CNN)simulations,demonstrating high accuracy in brain-like pattern recognition.

The Algorithm of Intelligent Compensation in Flexible Material Processing

Flexible material is easy to be distorted in high speed sewing process,so it must be tracked in the process. In this paper,The mathematics model is established with computer visual measure and digital image process for distorted flexible material. By the means of optimizing initial iterative value,the distorted variable of two correlated subareas evaluated. The method based on improved steepest descent algorithm and simulation annealing algorithm is proposed. It has been proven that the evaluating the algorithm’s error and convergent speed by the method of numerical emulate is the effective approach.

Nature-inspired materials and designs for flexible lithium-ion batteries

Flexible lithium-ion batteries(FLBs)are of critical importance to the seamless power supply of flexible and wearable electronic devices.However,the simultaneous acquirements of mechanical deformability and high energy density remain a major challenge for FLBs.Through billions of years of evolutions,many plants and animals have developed unique compositional and structural characteristics,which enable them to have both high mechanical deformability and robustness to cope with the complex and stressful environment.Inspired by nature,many new materials and designs emerge recently to achieve mechanically flexible and high storage capacity of lithiumion batteries at the same time.Here,we summarize these novel FLBs inspired by natural and biological materials and designs.We first give a brief introduction to the fundamentals and challenges of FLBs.Then,we highlight the latest achievements based on nature inspiration,including fiber-shaped FLBs,origami and kirigami-derived FLBs,and the nature-inspired structural designs in FLBs.Finally,we discuss the current status,remaining challenges,and future opportunities for the development of FLBs.This concise yet focused review highlights current inspirations in FLBs and wishes to broaden our view of FLB materials and designs,which can be directly“borrowed”from nature.

Recent advances in flexible alkaline zinc-based batteries:Materials,structures,and perspectives

The development of wearable electronic systems has generated increasing demand for flexible power sources.Alkaline zinc(Zn)-based batteries,as one of the most mature energy storage technologies,have been considered as a promising power source owing to their exceptional safety,low costs,and outstanding electrochemical performance.However,the conventional alkaline Zn-based battery systems face many challenges associated with electrodes and electrolytes,causing low capacity,poor cycle life,and inferior mechanical performance.Recent advances in materials and structure design have enabled the revisitation of the alkaline Zn-based battery technology for applications in flexible electronics.Herein,we summarize the up-to-date works in flexible alkaline Zn-based batteries and analyze the strategies employed to improve battery performance.Firstly,we introduce the three most reported cathode materials(including Ag-based,Ni-based,and Co-based materials)for flexible alkaline Zn-based batteries.Then,challenges and modifications in battery anodes are investigated.Thirdly,the recently advanced gel electrolytes are introduced from their properties,functions as well as advanced fabrications.Finally,recent works and the advantages of sandwich-type,fiber-type and thin film-type flexible batteries are summarized and compared.This review provides insights and guidance for the design of high-performance flexible Zn-based batteries for next-generation electronics.

Melting and Solidification Heat Transfer Characteristics of a Phase-Change Material in a Latent Heat Storage Vessel: Effects of a Perforated Partition Plate and Metal Fiber

Today, latent heat storage technology has advanced to allow reuse of waste heat in the middle-temperature range. This paper describes an approach to develop a latent heat storage system using middle-temperature waste heat (~100oC - 200oC) from factories. Direct contact melting and solidification behavior between a heat-transfer fluid (oil) and a latent heat storage material mixture were observed. The mixture consisted of mannitol and erythritol (Cm = 70 mass %, Ce = 30 mass %) as a phase-change material (PCM). The weight of the PCM was 3.0 kg and the flow rate of the oil, foil, was 1.0, 1.5, or 2.0 kg/min. To decrease the solidified height of the PCM mixture during the solidification process, a perforated partition plate was installed in the PCM region in the heat storage vessel. PCM coated oil droplets were broken by the perforated partition plate, preventing the solidified height of the PCM from increasing. The solidification and melting processes were repeated using metal fiber. It was found that installing the metal fiber was more effective than installing the perforated partition plate to prevent the flow out problem of the PCM.

Deformable Catalytic Material Derived from Mechanical Flexibility for Hydrogen Evolution Reaction

Deformable catalytic material with excellent flexible structure is a new type of catalyst that has been applied in various chemical reactions,especially electrocatalytic hydrogen evolution reaction(HER).In recent years,deformable catalysts for HER have made great progress and would become a research hotspot.The catalytic activities of deformable catalysts could be adjustable by the strain engineering and surface reconfiguration.The surface curvature of flexible catalytic materials is closely related to the electrocatalytic HER properties.Here,firstly,we systematically summarized self-adaptive catalytic performance of deformable catalysts and various micro–nanostructures evolution in catalytic HER process.Secondly,a series of strategies to design highly active catalysts based on the mechanical flexibility of lowdimensional nanomaterials were summarized.Last but not least,we presented the challenges and prospects of the study of flexible and deformable micro–nanostructures of electrocatalysts,which would further deepen the understanding of catalytic mechanisms of deformable HER catalyst.

Gel-Based Triboelectric Nanogenerators for Flexible Sensing:Principles,Properties,and Applications

The rapid development of the Internet of Things and artificial intelligence technologies has increased the need for wearable,portable,and self-powered flexible sensing devices.Triboelectric nanogenerators(TENGs)based on gel materials(with excellent conductivity,mechanical tunability,environmental adaptability,and biocompatibility)are considered an advanced approach for developing a new generation of flexible sensors.This review comprehensively summarizes the recent advances in gel-based TENGs for flexible sensors,covering their principles,properties,and applications.Based on the development requirements for flexible sensors,the working mechanism of gel-based TENGs and the characteristic advantages of gels are introduced.Design strategies for the performance optimization of hydrogel-,organogel-,and aerogel-based TENGs are systematically summarized.In addition,the applications of gel-based TENGs in human motion sensing,tactile sensing,health monitoring,environmental monitoring,human-machine interaction,and other related fields are summarized.Finally,the challenges of gel-based TENGs for flexible sensing are discussed,and feasible strategies are proposed to guide future research.