Investigations of the mechanical response of dummy HTPB propellant grain under ultrahigh acceleration overload conditions using onboard flight-test measurements

In this paper,to study the mechanical responses of a solid propellant subjected to ultrahigh acceleration overload during the gun-launch process,specifically designed projectile flight tests with an onboard measurement system were performed.Two projectiles containing dummy HTPB propellant grains were successfully recovered after the flight tests with an ultrahigh acceleration overload value of 8100 g.The onboard-measured time-resolved axial displacement,contact stress and overload values were successfully obtained and analysed.Uniaxial compression tests of the dummy HTPB propellant used in the gunlaunched tests were carried out at low and intermediate strain rates to characterize the propellant's dynamic properties.A linear viscoelastic constitutive model was employed and applied in finite-element simulations of the projectile-launching process.During the launch process,the dummy propellant grain exhibited large deformation due to the high acceleration overload,possibly leading to friction between the motor case and propellant grain.The calculated contact stress showed good agreement with the experimental results,though discrepancies in the overall displacement of the dummy propellant grain were observed.The dynamic mechanical response process of the dummy propellant grain was analysed in detail.The results can be used to estimate the structural integrity of the analysed dummy propellant grain during the gun-launch process.

Application of Filming Technique in the DUS Test for PVP Information

As the great progress has appeared in the field of protection of new varieties of plants, the standardization of the DUS （Distinctness, Uniformity, Stability） test procedure has become more important. However, the specification of filming technique plays an important role in the DUS test of new varieties of plants. In this paper, we analyzed the status quo and significance of the application of filming technique in the PVP （Plant Variety Protection） system, and provided an introduction about the application of filming technique in DUS test in China.

Automated Flight Test and System Identification for Rotary Wing Small Aerial Platform Using Frequency Responses Analysis

This paper proposes an autopilot system that can be used to control the small scale rotorcraft during the flight test for linear-frequency-domain system identification. The input frequency-sweep is generated automatically as part of the autopilot control command. Therefore the bandwidth coverage and consistency of the frequency-sweep are guaranteed to produce high quality data for system identification. Beside that, we can set the safety parameters during the flight test （maximum roll/pitch value, minimum altitude, etc.） so the safety of the whole flight test is guaranteed. This autopilot system is validated using hardware in the loop simulator for hover flight condition.

UAV flight test of plasma slats and ailerons with microsecond dielectric barrier discharge

Plasma flow control（PFC） is a promising active flow control method with its unique advantages including the absence of moving components, fast response, easy implementation, and stable operation. The effectiveness of plasma flow control by microsecond dielectric barrier discharge（μs-DBD）, and by nanosecond dielectric barrier discharge（NS-DBD） are compared through the wind tunnel tests, showing a similar performance between μs-DBD and NS-DBD. Furthermore, theμs-DBD is implemented on an unmanned aerial vehicle（UAV）, which is a scaled model of a newly developed amphibious plane. The wingspan of the model is 2.87 m, and the airspeed is no less than 30 m/s. The flight data, static pressure data,and Tufts images are recorded and analyzed in detail. Results of the flight test show that the μs-DBD works well on board without affecting the normal operation of the UAV model. When the actuators are turned on, the stall angle and maximum lift coefficient can be improved by 1.3° and 10.4%, and the static pressure at the leading edge of the wing can be reduced effectively in a proper range of angle of attack, which shows the ability of μs-DBD to act as plasma slats. The rolling moment produced by left-side μs-DBD actuation is greater than that produced by the maximum deflection of ailerons,which indicates the potential of μs-DBD to act as plasma ailerons. The results verify the feasibility and efficacy of μs-DBD plasma flow control in a real flight and lay the foundation for the full-sized airplane application.

Hybrid Model Testing Technique for Deep-Sea Platforms Based on Equivalent Water Depth Truncation

In this paper, an inner turret moored FPSO which works in the water of 320 m depth, is selected to study the socalled ＂passively-truncated ＋ numerical-simulation＂ type of hybrid model testing technique while the tnmcated water depth is 160 m and the model scale ）, = 80. During the investigation, the optimization design of the equivalent-depth truncated system is performed by using the similarity of the static characteristics between the truncated system and the full depth one as the objective function. According to the truncated system, the corresponding physical test model is made. By adopting the coupling time domain simulation method, the tnmcated system model test is numerically reconstructed to carefully verify the computer simulation software and to adjust the corresponding hydrodynamic parameters. Based on the above work, the numerical extrapolation to the full depth system is performed by using the verified computer software and the adjusted hydrodyrmmic parameters. The full depth system model test is then performed in the basin and the results are compared with those from the numerical extrapolation. At last, the implementation procedure and the key technique of the hybrid model testing of the deep-sea platforms are summarized and printed. Through the above investigations, some beneficial conclusions are presented.

Intravenous Contrast Material Administration at High-pitch Dual-source CT Coronary Angiography: Bolus-tracking Technique with Shortened Time of Respiratory Instruction Versus Test Bolus Technique

Objective To investigate the feasibility of acquiring the similar homogeneous enhancement using bolus-tracking techniques with shortened respiratory time in prospectively electrocardiogram-gated high-pitch spiral acquisition mode (Flash mode) coronary computed tomography angiography (CCTA) compared with test bolus technique. Methods One hundred and eighty-four consecutive patients with mean heart rate ≤65 beats per minute undergoing CCTA were prospectively included in this study. The patients were randomly divided into two groups. Patients in the group A (n=92) instructed to shorten respiratory time received CCTA using bolus-tracking technique with high-pitch spiral acquisition mode (Flash mode), while those in the group B (n=92) underwent CCTA with test bolus technique. The attenuation in the ascending aorta, image noise, contrast-to-noise ratio and radiation doses of the two groups were assessed. Results There were no significant differences in the mean attenuation values in the ascending aorta (483.18±59.07 HU vs. 498.7±83.51 HU, P=0.183), image noise (21.4±4.5 HU vs. 20.9±4.3 HU, P=0.414), contrast-to-noise ratio (12.1±4.2 vs. 13.8±5.1, P=0.31) between the groups A and B. There were no significant differences in the radiation dose of dynamic monitoring scans (0.056±0.026 mSv vs. 0.062±0.018 mSv, P=0.068) and radiation dose of angiography (0.94±0.07 mSv vs. 0.96±0.15 mSv,P=0.926) between the two groups, while 15 mL less contrast material volume was administered in the group A than the group B. Conclusion Bolus-tracking technique with shortened time of respiratory in Flash mode of dual-source CT yields the similar homogeneous enhancement with less contrast material in comparison to the test bolus technique.

Substructure hybrid testing of reinforced concrete shear wall structure using a domain overlapping technique

An online hybrid test was carried out on a 40-story 120-m high concrete shear wall structure. The structure was divided into two substructures whereby a physical model of the bottom three stories was tested in the laboratory and the upper 37 stories were simulated numerically using ABAQUS. An overlapping domain method was employed for the bottom three stories to ensure the validity of the boundary conditions of the superstructure. Mixed control was adopted in the test. Displacement control was used to apply the horizontal displacement, while two controlled force actuators were applied to simulate the overturning moment, which is very large and cannot be ignored in the substructure hybrid test of high-rise buildings. A series of tests with earthquake sources of sequentially increasing intensities were carried out. The test results indicate that the proposed hybrid test method is a solution to reproduce the seismic response of high-rise concrete shear wall buildings. The seismic performance of the tested precast high-rise building satisfies the requirements of the Chinese seismic design code.

Research on Model Construction and Technique Support for Integrated Rehabilitation of Rock Desertification in Chaoying Small Watershed of Bijie Test Area of Guizhou Province

Selecting Chaoying small watershed with representative karst rocky desertification in the Bijie test area of Guizhou Province as an example, according to karst rocky desertiflcation degree and the existing eco-environmental problems in the small watershed, we study developmental model and technique support system for integrated rehabilitation of rocky desertification in the small watershed, and bring forward the development model and technique integration for integrated rehabilitation of rocky desertification, which adapt to the karst areas of Bijie test area, Guizhou Province and even South China.

Advances in DUS Test Technique for Coconut

As great progress has been made in the field of protection of new plant varieties, more attention is paid to the standardization of DUS(Distinctness, Uniformity, and Stability) test procedure. For further studies of tropical plants as their importance in agriculture and germplasm, protection of coconut becomes more significant and thus DUS test technique of coconut is needed. In this essay, we analyzed the status quo of the DUS test guidelines by International Union for the Protection of New Varieties of Plants(UPOV proj.3) and national DUS test guidelines in China, and provided some suggestions or promotions for improving the guidelines of DUS test in coconut.

Is forced oscillation technique the next respiratory function test of choice in childhood asthma

Respiratory diseases, especially asthma, are common in children. While spirometry contributes to asthma diagnosis and management in older children, it has a limited role in younger children whom are often unable to perform forced expiratory manoeuvre. The development of novel diagnostic methods which require minimal effort, such as forced oscillation technique(FOT) is, therefore, a welcome and promising addition. FOT involves applying external, small amplitude oscillations to the respiratory system during tidal breathing. Therefore, it requires minimal effort and cooperation. The FOT has the potential to facilitate asthma diagnosis and management in preschool children by faciliting the objective measurement of baseline lung function and airway reactivity in children unable to successfully perform spirometry. Traditionally the use of FOT was limited to specialised centres. However, the availability of commercial equipment resulted in its use both in research and in clinical practice. In this article, we review the available literature on the use of FOT in childhood asthma. The technical aspects of FOT are described followed by a discussion of its practical aspects in the clinical field including the measurement of baseline lung function and associated reference ranges, bronchodilator responsiveness and bronchial hyperresponsiveness. We also highlight the difficulties and limitations that might be encountered and future research directions.

Calculation of the reactor neutron time of flight spectrum by convolution technique

It is a very complex and time-consuming process to simulate the nuclear reactor neutron spectrum from the reactor core to the export channel by applying a Monte Carlo program. This paper presents a new method to calculate the neutron spectrum by using the convolution technique which considers the channel transportation as a linear system and the transportation scattering as the response function. It also applies Monte Carlo Neutron and Photon Transport Code （MCNP） to simulate the response function numerically. With the application of convolution technique to calculate the spectrum distribution from the core to the channel, the process is then much more convenient only with the simple numerical integral numeration. This saves computer time and reduces some trouble in re-writing of the MCNP program.

Optimized Robust Filter for Uncertain Discrete Time System and Its Application to Flight Test

An optimized robust filtering algorithm for uncertain discrete-time systemsis presented. To get a series of computational equations, the uncertain part generated by theuncertain systematic matrix in the expression of the error-covariance matrix of time update stateestimation is optimized and the least upper bound of the uncertain part is given. By means of theseresults, the equivalent systematic matrix is obtained and a robust time update algorithm is builtup. On the other hand, uncertain parts generated by the uncertain observation matrix in theexpression of the error-covariance matrix of measurement update state estimation are optimized, andthe largest lower bound of the uncertain part is given. Thus both the time update and measurementupdate algorithms are developed. By means of the matrix inversion formula, the expression structuresof both time update and measurement update algorithms are all simplified. Moreover, the convergencecondition of a robust filter is developed to make the results easy to application. The results offlight data processing show that the method presented in this paper is efficient.

A Parallel Hybrid Testing Technique for Tri-Programming Model-Based Software Systems

Recently,researchers have shown increasing interest in combining more than one programming model into systems running on high performance computing systems(HPCs)to achieve exascale by applying parallelism at multiple levels.Combining different programming paradigms,such as Message Passing Interface(MPI),Open Multiple Processing(OpenMP),and Open Accelerators(OpenACC),can increase computation speed and improve performance.During the integration of multiple models,the probability of runtime errors increases,making their detection difficult,especially in the absence of testing techniques that can detect these errors.Numerous studies have been conducted to identify these errors,but no technique exists for detecting errors in three-level programming models.Despite the increasing research that integrates the three programming models,MPI,OpenMP,and OpenACC,a testing technology to detect runtime errors,such as deadlocks and race conditions,which can arise from this integration has not been developed.Therefore,this paper begins with a definition and explanation of runtime errors that result fromintegrating the three programming models that compilers cannot detect.For the first time,this paper presents a classification of operational errors that can result from the integration of the three models.This paper also proposes a parallel hybrid testing technique for detecting runtime errors in systems built in the C++programming language that uses the triple programming models MPI,OpenMP,and OpenACC.This hybrid technology combines static technology and dynamic technology,given that some errors can be detected using static techniques,whereas others can be detected using dynamic technology.The hybrid technique can detect more errors because it combines two distinct technologies.The proposed static technology detects a wide range of error types in less time,whereas a portion of the potential errors that may or may not occur depending on the 4502 CMC,2023,vol.74,no.2 operating environment are left to the dynamic technology,which completes the validation.

Big Data Testing Techniques:Taxonomy,Challenges and Future Trends

Big Data is reforming many industrial domains by providing decision support through analyzing large data volumes.Big Data testing aims to ensure that Big Data systems run smoothly and error-free while maintaining the performance and quality of data.However,because of the diversity and complexity of data,testing Big Data is challenging.Though numerous research efforts deal with Big Data testing,a comprehensive review to address testing techniques and challenges of BigData is not available as yet.Therefore,we have systematically reviewed the Big Data testing techniques’evidence occurring in the period 2010–2021.This paper discusses testing data processing by highlighting the techniques used in every processing phase.Furthermore,we discuss the challenges and future directions.Our findings show that diverse functional,non-functional and combined(functional and non-functional)testing techniques have been used to solve specific problems related to Big Data.At the same time,most of the testing challenges have been faced during the MapReduce validation phase.In addition,the combinatorial testing technique is one of the most applied techniques in combination with other techniques(i.e.,random testing,mutation testing,input space partitioning and equivalence testing)to find various functional faults through Big Data testing.

A Smart Substation Field Secondary Device Testing Technique Based on Recurrence Principle

According to the demand of substation secondary device dynamic performance testing, a smart substation field testing technique based on recurrence principle is proposed in the paper, and the characteristics of smart substation secondary device digitization and information sharing are used by the technique. The principle of testing technique is as follow: the digital simulation model is constructed on the basis of the substation’s actual construction, then the simulating data highly similar to substation’s actual electric quantity transient process is generated, at last, the substation digital secondary device can be tested by using data “recurrence” technique. The testing technique is verified and applied by constructing testing system, the application results show that the technique can effectively perform field test on the dynamic performance of digital secondary device, and the technique has good engineering implementation and application value.

Airborne test flight of HY-2A satellite microwave scatterometer and data analysis

This paper introduces the background, aim, experimental design, configuration and data processing for an airborne test flight of the HY-2 Microwave scatterometer(HSCAT). The aim was to evaluate HSCAT performance and a developed data processing algorithm for the HSCAT before launch. There were three test flights of the scatterometer, on January 15, 18 and 22, 2010, over the South China Sea near Lingshui, Hainan. The test flights successfully generated simultaneous airborne scatterometer normalized radar cross section(NRCS), ASCAT wind, and ship-borne-measured wind datasets, which were used to analyze HSCAT performance. Azimuthal dependence of the NRCS relative to the wind direction was nearly cos(2w), with NRCS minima at crosswind directions, and maxima near upwind and downwind. The NRCS also showed a small difference between upwind and downwind directions, with upwind crosssections generally larger than those downwind. The dependence of airborne scatterometer NRCS on wind direction and speed showed favorable consistency with the NASA scatterometer geophysical model function(NSCAT GMF), indicating satisfactory HSCAT performance.

Measurement of Ca^(2+) Flow in Cochlear Cells Using Non-Invasive Micro-Test Technique

Objective To test Calcium ion(Ca2+) flow at the head and end of outer hair cells(OHCs) in resting state and in response to Nimodipine treatment.Methods Non-invasive micro-test techniques were used to study Ca2+ in isolated OHCs in adult guinea pigs.Results Four types of Ca2+ transport were identified in OHCs on basilar membrane tissue fragments:influx at the head of with efflux at the bottom(type 1):efflux at the head of OHCs with influx at the bottom(type 2);influx at the both head and bottom(type 3);and efflux at the both head and bottom(type 4).However,only type 1 and type 3 of Ca2+ ion transport were detected in the cochlea.We propose that Ca2+ ion transport exists in adult guinea pig cochlear OHCs in resting state and is variable.Ca2 + flow in OHC can be inhibited by Nimodipine in resting state.