Equivalent Method of Integrated Power Generation System of Wind, Photovoltaic and Energy Storage in Power Flow Calculation and Transient Simulation

针对工程实际开展风光储联合发电系统在潮流计算和机电暂态仿真中的等值方法研究，旨在为大容量风光储联合发电系统的并网仿真分析奠定基础。将潮流计算的等值分为单元机组和集电系统2部分来研究。单元机组等值采用根据不同控制模式选取不同节点类型的方法，针对集电系统等值提出基于损耗不变原则的方法。等值模型和详细模型的算例结果表明，潮流计算等值方法具有较好的精度。在机电暂态仿真动态等值中，基于实际工程计算的最严重工况分析原则，提出运行在满出力点的单机“倍乘”等值模型，为工程计算中的风光储联合发电系统动态等值提供了一种解决方案。

Analysis and management strategies for the low voltage problems of rural power grid based on the distribution network flow calculation method

For a long time, because of the lack of investment capital and enough attentions, the overall constructions of rural power grid were far behind than the urban power grid in Chongqing Jiangbei Power Company. The low voltage problems were highlighted in the rural power grid due to the characteristics of rural power grid. Using the distribution network flow calculation method, we evaluated the low voltage problems of the rural power grid which belongs to Chongqing Jiangbei Power Company. In addition, we collected the data of distribution transformers in electricity consumption peak period. Some practical management strategies were proposed by the analysis and evaluation of potential and appeared low voltage problems.

Calculation of Turbulent Flow with Pseudo-spectral Method

This paper deals with the numerical simulation of incompressible turbulent boundary flow of a flat plate with the pseudo-spectral matrix method. In order to appear more than 10 nodes in the turbulent base-stratum and transition of 43×43 computational grids,a coordinate transformation is put up from physical panel to computational panel. Several zero turbulent models are computed comparatively. The results are credible when comparing with the previous methods.

Algebraic Calculation Method of One-Dimensional Steady Compressible Gas Flow

This paper describes a new method of calculation of one-dimensional steady compressible gas flows in channels with possible heat and mass exchange through perforated sidewalls. The channel is divided into small elements of a finite size for which mass, energy and momentum conservation laws are written in the integral form, assuming linear distribution of the parameters along the length. As a result, the calculation is reduced to finding the roots of a quadratic algebraic equation, thus providing an alternative to numerical methods based on differential equations. The advantage of this method is its high tolerance to coarse discretization of the calculation area as well as its good applicability for transonic flow calculations.

Effects of Numerical Methods on the Calculation of Developing Plane Channel Flow

In wall-bounded turbulent flow calculations, the past focus has been directed to the modelling of the Reynolds-stress gradients. Not much attention has been paid to the effects of the numerical methods used to calculate these terms and the modelled equations. Discrepancies between model calculations and measurements are quite often attributed to incorrect modelling, while the suitability and accuracy of the numerical methods used are seldom scrutinized. Instead, alternate near-wall and Reynolds-stress models are proposed to remedy the incorrect turbulent flow calculations. On the other hand, if care is not taken in the numerical treatment of the Reynolds-stress gradient terms, physically unrealistic results and solution instability could occur. Previous studies by the author and his collaborators on the effects of numerical methods have shown that some of the more commonly used numerical methods could enhance numerical stability in the solution procedure but would introduce considerable inaccuracy to the results. The flow cases chosen to demonstrate these inaccuracies are a backstep flow and flow in a square duct, where flow complexities are present. The current investigation attempts to show that the above-mentioned effects of numerical methods could also occur in the calculation of a developing plane channel flow, where flow complexities are absent. In addition, this study shows that the results thus obtained lead to a predicted skin friction coefficient that is influenced more by the numerical method used than by the turbulence model invoked. Together, these results show that numerical treatment of the Reynolds-stress gradients in the equations play an important role, even for a developing plane channel flow.

Optimal Design of High-Speed Partial Flow Pumps using Orthogonal Tests and Numerical Simulations

To investigate the influence of structural parameters on the performances and internal flow characteristics of partial flow pumps at a low specific speed of 10000 rpm,special attention was paid to the first and second stage impeller guide vanes.Moreover,the impeller blade outlet width,impeller inlet diameter,blade inclination angle,and number of blades were considered for orthogonal tests.Accordingly,nine groups of design solutions were formed,and then used as a basis for the execution of numerical simulations(CFD)aimed at obtaining the efficiency values and heads for each design solution group.The influence of impeller geometric parameters on the efficiency and head was explored,and the“weight”of each factor was obtained via a range analysis.Optimal structural parameters were finally chosen on the basis of the numerical simulation results,and the performances of the optimized model were verified accordingly(yet by means of CFD).Evidence is provided that the increase in the efficiency and head of the optimized model was 12.11%and 23.5 m,respectively,compared with those of the original model.

Formal Calculation and Invariant-Based Validation Establish Dependable Algorithmic Programs

The paper presents a formal and practical approach to dependable algorithm development.First,starting from a formal specification based on the Eindhoven quantifier notation,a problem is regularly reduced to subproblems with less complexity by using a concise set of calculation rules,the result of which establishes a recurrence-based algorithm.Second,a loop invariant is derived from the problem specification and recurrence,which certifies the transformation from the recurrence-based algorithm to one or more iterative programs.We demonstrate that our approach covers a number of classical algorithm design tactics,develops algorithmic programs together with their proof of correctness,and thus contributes fundamentally to the dependability of computer software.

CALCULATION ON TWO-PHASE FLOW TRANSIENTS AND THEIR EXPERIMENTAL RESEARCH

From basic equations of gas-liquid, solid-liquid, solid-gas two-phase flow,the calculating method on flow transients of two-phase flow is developed by means of characteristicmethod. As one example, a gas-liquid flow transient is calculated and it agrees well with theexperimental result. It is shown that the method is satisfactory for engineering demand.

Numerical Calculation of Transient Flow of Polymer Foam in Porous Media

Based on the mathematical model of one dimension transient flow of the polymer foam in porous media, the numerical calculation method of the flow mentioned above by using the finite difference method is given. Through the experiments of one dimension transient flow of HPAM (Hydrolytic Polyacrylamide) foam in the artificial sandstone core, the HPAM foam generation and coalescence coefficient of the mathematical model mentioned above are determined. The profiles of the liquid phase saturation, the pressure drop and the number density of one dimension transient flow of HPAM foam with the dimensionless time in artificial sandstone core are numerically calculated and analyzed by using the numerical calculation method.

Calculating Method for Influence of Material Flow on Energy Consumption in Steel Manufacturing Process

From the viewpoint of systems energy conservation, the influences of material flow on its energy consumption in a steel manufacturing process is an important subject. The quantitative analysis of the relationship between material flow and the energy intensity is useful to save energy in steel industry. Based on the concept of standard material flow diagram, all possible situations of ferric material flow in steel manufacturing process are analyzed. The expressions of the influence of material flow deviated from standard material flow diagram on energy consumption are put forward.

RESEARCH ON METHOD TO CALCULATE VELOCITIES OF SOLID PHASE AND LIQUID PHASE IN DEBRIS FLOW

Velocities of solid phase and liquid phase in debris flow are one key problem to research on impact and abrasion mechanism of banks and control structures under action of debris flow. Debris flow was simplified as two-phase liquid composed of solid phase with the same diameter particles and liquid phase with the same mechanical features. Assume debris flow was one-dimension two-phase liquid moving to one direction, then general equations of velocities of solid phase and liquid phase were founded in two-phase theory. Methods to calculate average pressures, volume forces and surface forces of debris flow control volume were established. Specially, surface forces were ascertained using Bingham＇s rheology equation of liquid phase and Bagnold＇s testing results about interaction between particles of solid phase. Proportional coefficient of velocities between liquid phase and solid phase was put forward, meanwhile, divergent coefficient between theoretical velocity and real velocity of solid phase was provided too. To state succinctly before, method to calculate velocities of solid phase and liquid phase was obtained through solution to general equations. The method is suitable for both viscous debris flow and thin debris flow. Additionally, velocities every phase can be identified through analyzing deposits in-situ after occurring of debris flow. It is obvious from engineering case the result in the method is consistent to that in real-time field observation.

Internal Flow Field Measurement of Gas Turbine Based on Optical Flow Method

The in-cylinder flow field of the internal combustion engine is an important factor affecting the quality and combustion quality of the fuel mixture in the cylinder. In order to calculate the high-precision flow field, the paper presents a flow field calculation method based on the optical flow algorithm. The motion of the point was calculated using the change in pixel intensity within two temporally adjacent frame images. The results show the high accuracy and resolution of the flow field at small displacement conditions.

基于Aquifertest计算大海则矿井水文地质参数及涌水量

抽水试验是一种在水文地质勘查中最为常用的水文地质试验,以榆林市大海则井田相关资料为依据,通过抽水试验,利用Aquifertest软件中的纽曼模型和博尔顿模型分别对水文地质参数进行确定,最终得出了相应的导水系数值为0.200 m^(2) /min、给水度值0.024、贮水系数值0.000177、渗透系数值4.434 m/d,并采用水平廊道法计算矿坑涌水量为大海则煤矿的涌水量为5169.351 m^(3) /d。此方法误差较小结果可靠,为快速高效地进行水文地质参数计算和涌水量预测提供一种有效方法,同时为后续矿床开采及施工建设提供参考依据。

温湿耦合大体积混凝土早龄期损伤试验研究

针对大体积混凝土温湿耦合损伤特性及其风险评价问题,依托上海某超大型污水处理厂工程,根据现场试验数据,研究了大体积混凝土结构内部温湿度空间分布及其时变规律;结合文献调查,探讨了多场耦合条件下混凝土在养护过程中水化度、抗拉强度、弹性模量等计算方法的工程适用性以及参数的合理取值,并对养护期混凝土结构损伤风险进行了定量评价。研究结果对大体积混凝土结构工程的抗裂防渗状态和质量评价具有借鉴意义。

前置宽体竖井进水流道水泵装置特性

为解决水泵机组设备布置与泵装置性能优化之间的矛盾,提出宽体竖井设计方法.基于三维湍流数值计算方法和熵产理论,比较了宽体竖井进水流道与2个常见的尖锥形竖井进水流道的水力特性.设计制作宽体竖井进水流道水泵装置模型,并试验测试5个叶片角下泵装置的能量特性、空化特性和飞逸特性.结果表明:宽体竖井方案与其他2个方案的内流场相似,在设计流量工况下流速均匀度均为95%左右,加权平均角度均大于89°;不同流量工况下,3种方案水力损失均接近,竖井前段熵产仅占后段的7.470%,竖井前段宽体型线对流道能量耗散无影响;当叶片角为0°时,水泵装置效率最高达79.19%;5个叶片角的泵装置临界空化余量均小于6.0 m;当叶片角为-6°时,扬程为2.36 m的最大飞逸转速为278.6 r/min;宽体竖井的水力特性与常规竖井相近,具有可同时满足设备布置与泵装置性能需求的特点.

n^(+)/n^(-)型硅衬底扩散片X_(jn+)理论分析与测试方法优化

n型衬底扩散片扩散深度(X_(jn+))是n^(+)/n^(-)型硅衬底扩散片最重要的参数之一,X_(jn+)的理论计算对磷扩散生产和X_(jn+)测试具有重要的指导意义。但现有扩散理论计算结果与实验数据差异较大,需更精准的计算方法。通过实验对X_(jn+)的测试与理论计算结果进行对比分析,引入了修正系数k_(n)与k_(p),得到理论计算与测试结果吻合的X_(jn+)计算方法。并根据修正后的计算方法对染色法测试X_(jn+)进行了优化。新的X_(jn+)计算方法得到的结果与测试结果差异小于2%,可用于指导生产,且优化后的X_(jn+)测试方法更加便捷。

Rainfall Threshold Calculation Method for Debris Flow Pre-Warning in Data-Poor Areas

Debris flows are the one type of natural disaster that is most closely associated with hu- man activities. Debris flows are characterized as being widely distributed and frequently activated. Rainfall is an important component of debris flows and is the most active factor when debris flows oc- cur. Rainfall also determines the temporal and spatial distribution characteristics of the hazards. A reasonable rainfall threshold target is essential to ensuring the accuracy of debris flow pre-warning. Such a threshold is important for the study of the mechanisms of debris flow formation, predicting the characteristics of future activities and the design of prevention and engineering control measures. Most mountainous areas have little data regarding rainfall and hazards, especially in debris flow forming re- gions. Therefore, both the traditional demonstration method and frequency calculated method cannot satisfy the debris flow pre-warning requirements. This study presents the characteristics of pre-warning regions, included the rainfall, hydrologic and topographic conditions. An analogous area with abundant data and the same conditions as the pre-warning region was selected, and the rainfall threshold was calculated by proxy. This method resolved the problem of debris flow pre-warning in ar- eas lacking data and provided a new approach for debris flow pre-warning in mountainous areas.

THE MODEL TEST RESEARCH OF HORIZONTAL FORCE ON RIGID SHAFT FURNITURE IN DEEP MINE

The state of deep mine rigid shaft fUrniture horizontal force calculation in China is introduced and the calculating model of horizontal force is determined. Based on the interaction between hoisting vessel and shaft furniture, the vertical mobel test device is built and a large number of model tests and analyses are carried out. At last, the relationship between horizontal force and hoisting end load, hoisting speed or bunton level interval is gained. The three parameters horizontal force calculating equation of beep mine rigid shaft furniture is given and it can guide the design and calculation of shaft engineering.

主动配电网潮流的全纯嵌入计算方法

配电网潮流计算是进行配电网规划和运行的重要基础。目前,配电网潮流求解方法主要有牛拉(Newton Raphson,NR)法和前推回代(forward backward substitution,FBS)法两大类,但NR法和FBS法在潮流收敛性和计算效率等方面均存在一定的不足。全纯嵌入法(holomorphic embedding method,HEM)是一种求解非线性潮流方程的新方法,它可以有效避免NR法和FBS法在配电网潮流求解过程中出现的上述问题,但现有HEM未充分考虑配电网中各类型分布式电源(distributed generation,DG)和智能软开关(soft open point,SOP)控制方式的多样性,且未构建计及负荷电压特性和频率特性的潮流模型,难以适用于不同运行模式下配电网潮流计算。针对上述问题,提出一种可求解含多类型DG和SOP且可运行在并网/孤岛模式的主动配电网统一全纯嵌入潮流计算方法。首先,根据负荷静态电压和频率特性,构建计及配电网频率和节点电压影响的负荷节点全纯嵌入潮流模型;其次,根据DG不同的控制方式以及配电网不同的运行模式,将DG所连节点等效为不同节点类型,构建各类DG的全纯嵌入潮流模型;再次,考虑SOP不同控制方式,构建SOP全纯嵌入潮流模型;从次,依据全纯嵌入潮流模型等式左右两侧同次幂级数系数相等原则,推导配电网各全纯函数幂级数系数的求解递推关系式,进而计算各全纯函数的各项幂级数系数,借助解析延拓理论求取电压和频率逼近值,实现配电网潮流的准确求解;最后,通过修改的IEEE-33节点测试系统和IEEE-123节点测试系统验证所提方法准确性和有效性。

基于子循环自适应串行交错时间匹配算法的油浸式变压器绕组瞬态温升计算

针对传统算法存在的步长调整及耦合点选择问题,该文提出基于子循环自适应串行交错(SCAS)的时间匹配算法。首先,在步长调整方面,通过加入自适应(ATS)-启发式(HTS)混合变步长算法,解决步长无法实时调整的问题;然后,针对耦合点选择问题,该文在传统常规串行交错(CSS)时间匹配算法及现有改进方案子循环常规串行交错(SCSS)的基础上,提出SCAS时间匹配算法,采用自适应方案确定计算时间窗及预定耦合点,并引入指数平滑法对其精度进行保证;最后,该文基于110 kV油浸式电力变压器建立二维瞬态单分区分匝绕组模型,并将所提算法与其他传统方法进行对比分析。结果表明:在精度方面,与传统CSS算法相比SCAS算法的流场及温度场最大平均相对误差均不超过0.45%,在可接受误差范围内;在效率方面,SCAS算法总体计算效率较CSS算法提高了近20倍。同时,为了说明所提算法的工程价值,该文搭建基于110 kV变压器绕组模型的温升实验平台,将SCAS时间匹配算法应用于该模型中,实验结果表明:在精度方面,SCAS算法与实验达到稳态时最大绝对误差为2.7 K;在计算效率上,本文所提算法的计算效率较传统算法提升约46倍,计算步数约为传统的1/47,减少了计算冗余。