Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during ...Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during casting,which are crucial for the quality of the ingot and can determine the success or failure of the casting operation.Numerical simulation,with the advantages of low cost,rapid execution,and visualized results,is an important method to study and optimize the DC casting process.In the present work,a simulation model of DC casting 2024 aluminum alloy was established,and the reliability of the model was verified.Then,the influence of casting parameters on flow field and temperature field was studied in detail by numerical simulation method.Results show that with the increase of casting speed,the melt flow becomes faster,the depths of slurry zone and mushy zone increase,and the variation of slurry zone depth is greater than that of mushy zone.With an increase in casting temperature,the melt flow rate increases,the depth of the slurry zone becomes shallower,and the depth of the mushy zone experiences only minor changes.The simulation results further indicate that the increase of the flow rate of the secondary cooling water slightly reduces the depths of both slurry and mushy zone.展开更多
Wind-sand flow generates erosion and deposition around obstacles such as bridges and roadbeds, resulting in sand damage and endangering railway systems in sandy regions. Previous studies have mainly focused on the flo...Wind-sand flow generates erosion and deposition around obstacles such as bridges and roadbeds, resulting in sand damage and endangering railway systems in sandy regions. Previous studies have mainly focused on the flow field around roadbeds, overlooking detailed examinations of sand particle erosion and deposition patterns near bridges and roadbeds. This study employs numerical simulations to analyze the influence of varying heights and wind speeds on sand deposition and erosion characteristics at different locations: the bridge-road transition section(side piers), middle piers, and roadbeds. The results show that the side piers, experience greater accumulation than the middle piers. Similarly, the leeward side of the roadbed witnesses more deposition compared to the windward side. Another finding reveals a reduced sand deposition length as the vertical profile, in alignment with the wind direction, moves further from the bridge abutments at the same clearance height. As wind speeds rise, there’s a decline in sand deposition and a marked increase in erosion around the side piers, middle piers and roadbeds. In conclusion, a bridge clearance that’s too low can cause intense sand damage near the side piers, while an extremely high roadbed may lead to extensive surface sand deposition. Hence, railway bridges in areas prone to sandy winds should strike a balance in clearance height. This research provides valuable guidelines for determining the most suitable bridge and roadbed heights in regions affected by wind and sand.展开更多
Wind and sand hazards are serious in the Milan Gobi area of the Xinjiang section of the Korla Railway. In order to ensure the safe operation of railroads, there is a need for wind and sand protection in heavily sandy ...Wind and sand hazards are serious in the Milan Gobi area of the Xinjiang section of the Korla Railway. In order to ensure the safe operation of railroads, there is a need for wind and sand protection in heavily sandy areas. The wind and sand flow in the region is notably bi-directional. To shield railroads from sand, a unique sand fence made of folded linear high-density polyethylene(HDPE) is used, aligning with the principle that the dominant wind direction is perpendicular to the fence. This study employed field observations and numerical simulations to investigate the effectiveness of these HDPE sand fences in altering flow field distribution and offering protection. It also explored how these fences affect the deposition and erosion of sand particles. Findings revealed a significant reduction in wind speed near the fence corner;the minimum horizontal wind speed on the leeward side of the first sand fence(LSF) decreased dramatically from 3 m/s to 0.64 m/s. The vortex area on the LSF markedly impacted horizontal wind speeds. Within the LSF, sand deposition was a primary occurrence. As wind speeds increased, the deposition zone shrank, whereas the positive erosion zone expanded. Close to the folded corners of the HDPE sand fence, there was a notable shift from the positive erosion zone to a deposition zone. Field tests and numerical simulations confirmed the high windproof efficiency(WE) and sand resistance efficiency(SE) in the HDPE sand fence. Folded linear HDPE sheet sand fence can effectively slow down the incoming flow and reduce the sand content, thus achieving good wind and sand protection. This study provides essential theoretical guidance for the design and improvement of wind and sand protection systems in railroad engineering.展开更多
The so-called T-shaped reducing tees are typically used to divide,change and control(to a certain extent)the flow direction in pipe networks.In this study,the Ffowcs Williams–Hawkings(FW-H)equation and the Large Eddy...The so-called T-shaped reducing tees are typically used to divide,change and control(to a certain extent)the flow direction in pipe networks.In this study,the Ffowcs Williams–Hawkings(FW-H)equation and the Large Eddy Simulation(LES)methods are used to simulate the flow-induced noise related to T-shaped reducing tees under different inlet flow velocities and for different pipe diameter ratios.The results show that the maximum flow velocity,average flow velocity,and vorticity in the branch pipe increase gradually as the related diameter decreases.Strong vorticity and secondary flows are also observed in the branch pipe,and the associated violent pressure fluctuations are found to be the main sources of flow-induced noise.In particular,as the pipe diameter ratio decreases from 1 to 0.45,the Total Sound Pressure Level(TSPL)increases by 6.8,6.26,and 7.43 dB for values of the inlet flow velocity of 1,2,and 3 m/s,respectively.The distribution characteristics of the flow-induced noise in the frequency domain follow similar trends for different pipe diameter ratios.展开更多
During the electromagnetic railgun launching process,there will be a complex flow field with high temperature in the muzzle area because of the high-speed friction,transition and seco ndary arc-ignition.This paper mod...During the electromagnetic railgun launching process,there will be a complex flow field with high temperature in the muzzle area because of the high-speed friction,transition and seco ndary arc-ignition.This paper models the muzzle area of railgun when the projectile is far away from the muzzle,and the dynamic simulation of the flow field with secondary arc in the muzzle area is carried out based on the magneto hydrodynamic equations.Meanwhile,a multi-component plasma transport model is used to analyze the muzzle arc plasma flow process of the mixed gas of Al vapor and the air.Furthermore,the pressure boundary conditions are fitted by the dynamic mesh simulation results.The current and voltage of the muzzle are obtained through the emission experiment of the railgun experimental prototype.We load the current data into the simulation model and the voltage of experiments and simulations are compared,which proves the accuracy of the simulation.Then the plasma temperature and the composition of Al vapor in the muzzle flow process are analyzed in-depth.展开更多
Based on the casting manufacture practice of steel slabs by CSP technology, the flow and the temperature fields of the funnel mould and the secondary cooling segment were simulated using the commercial code, CFX4. Com...Based on the casting manufacture practice of steel slabs by CSP technology, the flow and the temperature fields of the funnel mould and the secondary cooling segment were simulated using the commercial code, CFX4. Compared with other physical investigations, the correlative data of the present simulation results are in good agreement with them. Therefore, a more comprehensive survey for metallurgy characteristic of the flow and the temperature fields in CSP continuous casting process can be achieved.展开更多
The flow field over Hainan Island and the Leizhou Peninsula in summer and winter is discussed with three-dimensional mesoscale model developed in the University of Virginia and using the representative meteorological ...The flow field over Hainan Island and the Leizhou Peninsula in summer and winter is discussed with three-dimensional mesoscale model developed in the University of Virginia and using the representative meteorological data of January and July.Simulation results indicate that the local weather characteristics over the Hainan Island are distinctly influenced by theWuzhi Mountain terrain. The cloudy or rainfall weather over the northeast of the Wuzhi Mountain occurs easily, under proper large-scale conditions of flow, temperature and humidity. while west wind prevails. The overcast or rainfall weather is often induced by strong convection in the afternoon over west of the Hainan Island under easterly prevailing wind.展开更多
The railway subgrades in the sandy areas act as an obstacle interfering wind-blown sand,causing sand erosion and sedimentation,which can disrupt the safe and stable operation of the railway system.Most previous studie...The railway subgrades in the sandy areas act as an obstacle interfering wind-blown sand,causing sand erosion and sedimentation,which can disrupt the safe and stable operation of the railway system.Most previous studies mainly focus on the flow field around railway subgrades,however,the real erosion and sedimentation patterns are rarely studied.This study aims to analyze the erosion and sand sedimentation patterns of wind-blown sand over the subgrades with different heights and steel rails using the ratio of the wall shear stress to the critical value of erosion shear stress.Results show that wind erosion near the top of the upwind slope of the embankment and the shoulder on the upwind side are more severe,and the severity increases with an increase in the height of the embankment.With the increase of wind velocity,sand sedimentation both on the windward and leeside of the subgrade decreases and wind erosion by reverse flow occur.This study indicates that railways in sandy areas should be constructed with a moderate subgrade height(4 m).展开更多
A three-dimension full-size numerical simulation of the effect of air distribution on turbulent flow and combustion in a tubular heating furnace was carried out. A standard k –ε turbulent model, a simplified PDF c...A three-dimension full-size numerical simulation of the effect of air distribution on turbulent flow and combustion in a tubular heating furnace was carried out. A standard k –ε turbulent model, a simplified PDF combustion model and a discrete ordinate transfer radiation model were used. The hybrid grid combining a structured and a non-structured grid was generated without any simplification of the complicated geometric configuration around the burner. It was found that the multistage combustion could reduce and control the peak value of temperature. At the same time, it was concluded that the amount of primary air had little effect on the global distribution of velocity and temperature in the furnace, but a great effect on that around the burner. It is recommended that 45% - 65% of the total amount of air be taken in in primary air inlets in the furnace. All the results are important to optimize the combustion progress.展开更多
In this work,by establishing a three-dimensional physical model of a 1000-ton industrial multi-jet combustion reactor,a hexahedral structured grid was used to discretize the model.Combined with realizable k–εmodel,e...In this work,by establishing a three-dimensional physical model of a 1000-ton industrial multi-jet combustion reactor,a hexahedral structured grid was used to discretize the model.Combined with realizable k–εmodel,eddy-dissipation-concept,discrete-ordinate radiation model,hydrogen 19-step detailed reaction mechanism,air age user-defined-function,velocity field,temperature field,concentration field and gas arrival time in the reactor were numerically simulated.The Euler–Lagrange method combined with the discrete-phase-model was used to reveal the flow characteristics of particles in the reactor,and based on this,the effects of the reactor aspect ratios,central jet gas velocity and particle size on the flow field characteristics and particle back-mixing degree in the reactor were investigated.The results show that with the decrease of aspect ratio in the combustion reactors,the velocity and temperature attenuation in the reactor are intensified,the vortex phenomenon is aggravated,and the residence time distribution of nanoparticles is more dispersed.With the increase in the central jet gas velocities in reactors,the vortex lengthens along the axis,the turbulence intensity increases,and the residence time of particles decreases.The back-mixing degree and residence time of particles in the reactor also decrease with the increase in particle size.The simulation results can provide reference for the structural regulation of nanoparticles and the structural design of combustion reactor in the process of gas combustion synthesis.展开更多
This article aims at building an electromagnetic and fluid model, based on the Maxwell equations and Navier-Stokes equations, in TiAl melt under two electric fields.FEM (Finite Element Method) and APDL (ANSYS Parametr...This article aims at building an electromagnetic and fluid model, based on the Maxwell equations and Navier-Stokes equations, in TiAl melt under two electric fields.FEM (Finite Element Method) and APDL (ANSYS Parametric Design Language) were employed to perform the simulation, model setup, loading and problem solving.The melt in molds of same cross section area with different flakiness ratio (i.e.width/depth) under the load of sinusoidal current or pulse current was analyzed to obtain the distribution of electromagnetic field and flow field.The results show that the induced magnetic field occupies sufficiently the domain of the melt in the mold with a flakiness ratio of 5:1.The melt is driven bipolarly from the center in each electric field.It is also found that the pulse electric field actuates the TiAl melt to flow stronger than what the sinusoidal electric field does.展开更多
Precise function expression of the flow area for the sloping U-shape notch orifice versus the spool stroke was derived.The computational fluid dynamics was used to analyze the flow features of the sloping U-shape notc...Precise function expression of the flow area for the sloping U-shape notch orifice versus the spool stroke was derived.The computational fluid dynamics was used to analyze the flow features of the sloping U-shape notch on the spool,such as mass flow rates,flow coefficients,efflux angles and steady state flow forces under different operating conditions.At last,the reliability of the mathematical model of the flow area for the sloping U-shape notch orifice on the spool was demonstrated by the comparison between the orifice area curve derived and the corresponding experimental data provided by the test.It is presented that the bottom arc of sloping U-shape notch(ABU) should not be omitted when it is required to accurately calculate the orifice area of ABU.Although the theoretical flow area of plain bottom sloping U-shape notch(PBU) is larger than that of ABU at the same opening,the simulated mass flow and experimental flow area of ABU are both larger than these of PBU at the same opening,while the simulated flow force of PBU is larger than that of ABU at the same opening.Therefore,it should be prior to adapt the ABU when designing the spool with proportional character.展开更多
The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The simulation is based on the two-equation RNG κ-ε turbulence model,...The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The simulation is based on the two-equation RNG κ-ε turbulence model, Eulerian multiphase model, mad a real-shape 3D model with a huge number of meshes. The simulation results include detailed information about velocity, pressure, volume fraction and so on. Some features of the flow field are obtained: liquid is atomized in a thin annular zone; a high velocity air zone prevents water drops at the bottom from flying towards the wall;the pressure varies sharply at the end of blades and so on. The results will be helpful for structure optimization and engineering design.展开更多
This article presents a study we have made of one class of coherent structures of the tripolar vortex. Considering the sheared flow and sheared magnetic field which are common in the thermonuclear plasma and space pla...This article presents a study we have made of one class of coherent structures of the tripolar vortex. Considering the sheared flow and sheared magnetic field which are common in the thermonuclear plasma and space plasma, we have simulated the dynamics of the tripolar vortex. The results show that the tripolar vortex is largely stable in most cases, but a strongly sheared magnetic field will make the structure less stable, and lead it to decays into single vortices with the large space scale. These results are consistent with findings from former research about the dipolar vortex.展开更多
The control rod drive mechanism(CRDM)is an essential part of the control and safety protection system of pressurized water reactors.Current CRDM simulations are mostly performed collectively using a single method,igno...The control rod drive mechanism(CRDM)is an essential part of the control and safety protection system of pressurized water reactors.Current CRDM simulations are mostly performed collectively using a single method,ignoring the influence of multiple motion units and the differences in various features among them,which strongly affect the efficiency and accuracy of the simulations.In this study,we constructed a flow field fusion simulation method based on model features by combining key motion unit analysis and various simulation methods and then applied the method to the CRDM simulation process.CRDM performs motion unit decomposition through the structural hierarchy of function-movement-action method,and the key meta-actions are identified as the nodes in the flow field simulation.We established a fused feature-based multimethod simulation process and processed the simulation methods and data according to the features of the fluid domain space and the structural complexity to obtain the fusion simulation results.Compared to traditional simulation methods and real measurements,the simulation method provides advantages in terms of simulation efficiency and accuracy.展开更多
In order to solve the problem of excessive noise and vibration during the operation of the hydraulic transformer,an optimization method of valve plate damping hole structure is proposed to alleviate the phenomenon of ...In order to solve the problem of excessive noise and vibration during the operation of the hydraulic transformer,an optimization method of valve plate damping hole structure is proposed to alleviate the phenomenon of pressure shock.Firstly,the mathematical model of oil pressure gradient in the plunger cavity is established,and the incremental equation of pressure change is derived.Secondly,a kind of buffering structure is proposed,the corresponding relationship between the pressure change and the envelopment angle of the buffering hole and the aperture size is determined by analyzing the oil pressure change curve in the plunger cavity.Finally,the flow field models with buffering holes are established,and the transient simulation of the pressure change process under the optimal solution is carried out with ANSYS software and the flow field pressure distribution contours are obtained.Through the analysis of simulation results,it is concluded that the optimal envelope angle of the three buffer holes ofA-T-B-Ais 5°,and the optimal aperture is 1.8 mm,1.6 mm,and 1.7 mm,respectively.The buffer hole can achieve a better-buffering effect in the range of variable pressure angle[0°,101°].The buffer hole structure can effectively alleviate the pressure shock and reduce the noise level,which lays a foundation for the design and theoretical research of hydraulic transformers.展开更多
New design of plain flow distributor of the radial piston low speed hydraulic motor is presented. On the basis of analyzing its static mathematic model and structural optimization, the kinetic characteristics of the d...New design of plain flow distributor of the radial piston low speed hydraulic motor is presented. On the basis of analyzing its static mathematic model and structural optimization, the kinetic characteristics of the distribution plates and the oil film between them are discussed in detail.展开更多
Based on turbulent theory, a 3D coupled model of fluid flow and solidification was built using finite difference method and used to study the influence of superheating degree and casting speed on fluid flow and solidi...Based on turbulent theory, a 3D coupled model of fluid flow and solidification was built using finite difference method and used to study the influence of superheating degree and casting speed on fluid flow and solidification, analyze the interaction between shell and molten steel, and compare the temperature distribution under different technological conditions. The results indicate that high superheating degree can lengthen the liquid-core depth and make the crack and breakout possible, so suitable superheating should be controlled within 35℃ according to the simulation results. Casting speed which is one of the most important technological parameters of improving production rate, should be controlled between 0. 85 m/min and 1.05 m/min and the caster has great potential in the improvement of blank quality.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51674078)。
文摘Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during casting,which are crucial for the quality of the ingot and can determine the success or failure of the casting operation.Numerical simulation,with the advantages of low cost,rapid execution,and visualized results,is an important method to study and optimize the DC casting process.In the present work,a simulation model of DC casting 2024 aluminum alloy was established,and the reliability of the model was verified.Then,the influence of casting parameters on flow field and temperature field was studied in detail by numerical simulation method.Results show that with the increase of casting speed,the melt flow becomes faster,the depths of slurry zone and mushy zone increase,and the variation of slurry zone depth is greater than that of mushy zone.With an increase in casting temperature,the melt flow rate increases,the depth of the slurry zone becomes shallower,and the depth of the mushy zone experiences only minor changes.The simulation results further indicate that the increase of the flow rate of the secondary cooling water slightly reduces the depths of both slurry and mushy zone.
基金financially supported by the fellowship of the China Postdoctoral Science Foundation (2021M703466)the Natural Science Foundation of Gansu Province, China (20JR10RA231)the Natural Science Foundation of Gansu Province, China (22JR5RA050)。
文摘Wind-sand flow generates erosion and deposition around obstacles such as bridges and roadbeds, resulting in sand damage and endangering railway systems in sandy regions. Previous studies have mainly focused on the flow field around roadbeds, overlooking detailed examinations of sand particle erosion and deposition patterns near bridges and roadbeds. This study employs numerical simulations to analyze the influence of varying heights and wind speeds on sand deposition and erosion characteristics at different locations: the bridge-road transition section(side piers), middle piers, and roadbeds. The results show that the side piers, experience greater accumulation than the middle piers. Similarly, the leeward side of the roadbed witnesses more deposition compared to the windward side. Another finding reveals a reduced sand deposition length as the vertical profile, in alignment with the wind direction, moves further from the bridge abutments at the same clearance height. As wind speeds rise, there’s a decline in sand deposition and a marked increase in erosion around the side piers, middle piers and roadbeds. In conclusion, a bridge clearance that’s too low can cause intense sand damage near the side piers, while an extremely high roadbed may lead to extensive surface sand deposition. Hence, railway bridges in areas prone to sandy winds should strike a balance in clearance height. This research provides valuable guidelines for determining the most suitable bridge and roadbed heights in regions affected by wind and sand.
基金financially supported by the Chang Jiang Scholar and Innovation Team Development Plan of China (IRT_15R29)the Basic Research Innovation Group Project of Gansu Province, China (21JR7RA347)the Natural Science Foundation of Gansu Province, China (20JR10RA231)。
文摘Wind and sand hazards are serious in the Milan Gobi area of the Xinjiang section of the Korla Railway. In order to ensure the safe operation of railroads, there is a need for wind and sand protection in heavily sandy areas. The wind and sand flow in the region is notably bi-directional. To shield railroads from sand, a unique sand fence made of folded linear high-density polyethylene(HDPE) is used, aligning with the principle that the dominant wind direction is perpendicular to the fence. This study employed field observations and numerical simulations to investigate the effectiveness of these HDPE sand fences in altering flow field distribution and offering protection. It also explored how these fences affect the deposition and erosion of sand particles. Findings revealed a significant reduction in wind speed near the fence corner;the minimum horizontal wind speed on the leeward side of the first sand fence(LSF) decreased dramatically from 3 m/s to 0.64 m/s. The vortex area on the LSF markedly impacted horizontal wind speeds. Within the LSF, sand deposition was a primary occurrence. As wind speeds increased, the deposition zone shrank, whereas the positive erosion zone expanded. Close to the folded corners of the HDPE sand fence, there was a notable shift from the positive erosion zone to a deposition zone. Field tests and numerical simulations confirmed the high windproof efficiency(WE) and sand resistance efficiency(SE) in the HDPE sand fence. Folded linear HDPE sheet sand fence can effectively slow down the incoming flow and reduce the sand content, thus achieving good wind and sand protection. This study provides essential theoretical guidance for the design and improvement of wind and sand protection systems in railroad engineering.
基金supported by the Shandong Engineering Laboratory for High-Efficiency Energy Conservation and Energy Storage Technology&Equipment.
文摘The so-called T-shaped reducing tees are typically used to divide,change and control(to a certain extent)the flow direction in pipe networks.In this study,the Ffowcs Williams–Hawkings(FW-H)equation and the Large Eddy Simulation(LES)methods are used to simulate the flow-induced noise related to T-shaped reducing tees under different inlet flow velocities and for different pipe diameter ratios.The results show that the maximum flow velocity,average flow velocity,and vorticity in the branch pipe increase gradually as the related diameter decreases.Strong vorticity and secondary flows are also observed in the branch pipe,and the associated violent pressure fluctuations are found to be the main sources of flow-induced noise.In particular,as the pipe diameter ratio decreases from 1 to 0.45,the Total Sound Pressure Level(TSPL)increases by 6.8,6.26,and 7.43 dB for values of the inlet flow velocity of 1,2,and 3 m/s,respectively.The distribution characteristics of the flow-induced noise in the frequency domain follow similar trends for different pipe diameter ratios.
文摘During the electromagnetic railgun launching process,there will be a complex flow field with high temperature in the muzzle area because of the high-speed friction,transition and seco ndary arc-ignition.This paper models the muzzle area of railgun when the projectile is far away from the muzzle,and the dynamic simulation of the flow field with secondary arc in the muzzle area is carried out based on the magneto hydrodynamic equations.Meanwhile,a multi-component plasma transport model is used to analyze the muzzle arc plasma flow process of the mixed gas of Al vapor and the air.Furthermore,the pressure boundary conditions are fitted by the dynamic mesh simulation results.The current and voltage of the muzzle are obtained through the emission experiment of the railgun experimental prototype.We load the current data into the simulation model and the voltage of experiments and simulations are compared,which proves the accuracy of the simulation.Then the plasma temperature and the composition of Al vapor in the muzzle flow process are analyzed in-depth.
基金Item Sponsored by Scientific Research Program Foundation of Shanghai City of China(04DZ05621)
文摘Based on the casting manufacture practice of steel slabs by CSP technology, the flow and the temperature fields of the funnel mould and the secondary cooling segment were simulated using the commercial code, CFX4. Compared with other physical investigations, the correlative data of the present simulation results are in good agreement with them. Therefore, a more comprehensive survey for metallurgy characteristic of the flow and the temperature fields in CSP continuous casting process can be achieved.
文摘The flow field over Hainan Island and the Leizhou Peninsula in summer and winter is discussed with three-dimensional mesoscale model developed in the University of Virginia and using the representative meteorological data of January and July.Simulation results indicate that the local weather characteristics over the Hainan Island are distinctly influenced by theWuzhi Mountain terrain. The cloudy or rainfall weather over the northeast of the Wuzhi Mountain occurs easily, under proper large-scale conditions of flow, temperature and humidity. while west wind prevails. The overcast or rainfall weather is often induced by strong convection in the afternoon over west of the Hainan Island under easterly prevailing wind.
基金financially supported by the Fellowship of the China Postdoctoral Science Foundation(2021M703466)the Natural Science Foundation of Gansu Province,China(20JR10RA231)+1 种基金the Basic Research Innovation Group Project of Gansu Province,China(21JR7RA347)Special Funds for Guiding Local Scientific and Technological Development by the Central Government(22ZY1QA005)。
文摘The railway subgrades in the sandy areas act as an obstacle interfering wind-blown sand,causing sand erosion and sedimentation,which can disrupt the safe and stable operation of the railway system.Most previous studies mainly focus on the flow field around railway subgrades,however,the real erosion and sedimentation patterns are rarely studied.This study aims to analyze the erosion and sand sedimentation patterns of wind-blown sand over the subgrades with different heights and steel rails using the ratio of the wall shear stress to the critical value of erosion shear stress.Results show that wind erosion near the top of the upwind slope of the embankment and the shoulder on the upwind side are more severe,and the severity increases with an increase in the height of the embankment.With the increase of wind velocity,sand sedimentation both on the windward and leeside of the subgrade decreases and wind erosion by reverse flow occur.This study indicates that railways in sandy areas should be constructed with a moderate subgrade height(4 m).
文摘A three-dimension full-size numerical simulation of the effect of air distribution on turbulent flow and combustion in a tubular heating furnace was carried out. A standard k –ε turbulent model, a simplified PDF combustion model and a discrete ordinate transfer radiation model were used. The hybrid grid combining a structured and a non-structured grid was generated without any simplification of the complicated geometric configuration around the burner. It was found that the multistage combustion could reduce and control the peak value of temperature. At the same time, it was concluded that the amount of primary air had little effect on the global distribution of velocity and temperature in the furnace, but a great effect on that around the burner. It is recommended that 45% - 65% of the total amount of air be taken in in primary air inlets in the furnace. All the results are important to optimize the combustion progress.
基金supported by the National Natural Science Foundation of China(21978088,91534202,51673063)Shanghai Technology Research Leader(20XD1433600)+4 种基金the Program for Professor of Special Appointment(Eastern Scholar)at Shanghai Institutes of High Learningthe Basic Research Program of Shanghai(17JC1402300)the Shanghai City Board of education research and innovation projectthe Fundamental Research Funds for the Central Universities(222201718002)provided by Feringa Nobel Prize Scientist Joint Research Center。
文摘In this work,by establishing a three-dimensional physical model of a 1000-ton industrial multi-jet combustion reactor,a hexahedral structured grid was used to discretize the model.Combined with realizable k–εmodel,eddy-dissipation-concept,discrete-ordinate radiation model,hydrogen 19-step detailed reaction mechanism,air age user-defined-function,velocity field,temperature field,concentration field and gas arrival time in the reactor were numerically simulated.The Euler–Lagrange method combined with the discrete-phase-model was used to reveal the flow characteristics of particles in the reactor,and based on this,the effects of the reactor aspect ratios,central jet gas velocity and particle size on the flow field characteristics and particle back-mixing degree in the reactor were investigated.The results show that with the decrease of aspect ratio in the combustion reactors,the velocity and temperature attenuation in the reactor are intensified,the vortex phenomenon is aggravated,and the residence time distribution of nanoparticles is more dispersed.With the increase in the central jet gas velocities in reactors,the vortex lengthens along the axis,the turbulence intensity increases,and the residence time of particles decreases.The back-mixing degree and residence time of particles in the reactor also decrease with the increase in particle size.The simulation results can provide reference for the structural regulation of nanoparticles and the structural design of combustion reactor in the process of gas combustion synthesis.
基金supported by the Program for New Century Excellent Talents in Universities of the Ministry of Education of China under Grant No.NCET-08-0164the Foundation of National Key Laboratory for Precision Heat Processing of Metals
文摘This article aims at building an electromagnetic and fluid model, based on the Maxwell equations and Navier-Stokes equations, in TiAl melt under two electric fields.FEM (Finite Element Method) and APDL (ANSYS Parametric Design Language) were employed to perform the simulation, model setup, loading and problem solving.The melt in molds of same cross section area with different flakiness ratio (i.e.width/depth) under the load of sinusoidal current or pulse current was analyzed to obtain the distribution of electromagnetic field and flow field.The results show that the induced magnetic field occupies sufficiently the domain of the melt in the mold with a flakiness ratio of 5:1.The melt is driven bipolarly from the center in each electric field.It is also found that the pulse electric field actuates the TiAl melt to flow stronger than what the sinusoidal electric field does.
基金Project(51004085)supported by the National Natural Science Foundation of China
文摘Precise function expression of the flow area for the sloping U-shape notch orifice versus the spool stroke was derived.The computational fluid dynamics was used to analyze the flow features of the sloping U-shape notch on the spool,such as mass flow rates,flow coefficients,efflux angles and steady state flow forces under different operating conditions.At last,the reliability of the mathematical model of the flow area for the sloping U-shape notch orifice on the spool was demonstrated by the comparison between the orifice area curve derived and the corresponding experimental data provided by the test.It is presented that the bottom arc of sloping U-shape notch(ABU) should not be omitted when it is required to accurately calculate the orifice area of ABU.Although the theoretical flow area of plain bottom sloping U-shape notch(PBU) is larger than that of ABU at the same opening,the simulated mass flow and experimental flow area of ABU are both larger than these of PBU at the same opening,while the simulated flow force of PBU is larger than that of ABU at the same opening.Therefore,it should be prior to adapt the ABU when designing the spool with proportional character.
基金Supported by the National 863 Project (2001AA642030-1) and Zhejiang Provincial Key Research Project (010007037).
文摘The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The simulation is based on the two-equation RNG κ-ε turbulence model, Eulerian multiphase model, mad a real-shape 3D model with a huge number of meshes. The simulation results include detailed information about velocity, pressure, volume fraction and so on. Some features of the flow field are obtained: liquid is atomized in a thin annular zone; a high velocity air zone prevents water drops at the bottom from flying towards the wall;the pressure varies sharply at the end of blades and so on. The results will be helpful for structure optimization and engineering design.
基金The project supported by the National Natural Science Foundation of China (Nos. 10075047, 40336052)
文摘This article presents a study we have made of one class of coherent structures of the tripolar vortex. Considering the sheared flow and sheared magnetic field which are common in the thermonuclear plasma and space plasma, we have simulated the dynamics of the tripolar vortex. The results show that the tripolar vortex is largely stable in most cases, but a strongly sheared magnetic field will make the structure less stable, and lead it to decays into single vortices with the large space scale. These results are consistent with findings from former research about the dipolar vortex.
基金supported by the National Natural Science Foundation of China (No. 52075350)the Special City School Strategic Cooperation Project of Sichuan University and Zigong (No.2021CDZG-3)
文摘The control rod drive mechanism(CRDM)is an essential part of the control and safety protection system of pressurized water reactors.Current CRDM simulations are mostly performed collectively using a single method,ignoring the influence of multiple motion units and the differences in various features among them,which strongly affect the efficiency and accuracy of the simulations.In this study,we constructed a flow field fusion simulation method based on model features by combining key motion unit analysis and various simulation methods and then applied the method to the CRDM simulation process.CRDM performs motion unit decomposition through the structural hierarchy of function-movement-action method,and the key meta-actions are identified as the nodes in the flow field simulation.We established a fused feature-based multimethod simulation process and processed the simulation methods and data according to the features of the fluid domain space and the structural complexity to obtain the fusion simulation results.Compared to traditional simulation methods and real measurements,the simulation method provides advantages in terms of simulation efficiency and accuracy.
基金Supported by the National Natural Science Foundation of China(No.51975164)Outstanding Youth of Pyramid Talent Training Project ofBeijing University of Civil Engineering and Architecture(No.GDRC20220801)。
文摘In order to solve the problem of excessive noise and vibration during the operation of the hydraulic transformer,an optimization method of valve plate damping hole structure is proposed to alleviate the phenomenon of pressure shock.Firstly,the mathematical model of oil pressure gradient in the plunger cavity is established,and the incremental equation of pressure change is derived.Secondly,a kind of buffering structure is proposed,the corresponding relationship between the pressure change and the envelopment angle of the buffering hole and the aperture size is determined by analyzing the oil pressure change curve in the plunger cavity.Finally,the flow field models with buffering holes are established,and the transient simulation of the pressure change process under the optimal solution is carried out with ANSYS software and the flow field pressure distribution contours are obtained.Through the analysis of simulation results,it is concluded that the optimal envelope angle of the three buffer holes ofA-T-B-Ais 5°,and the optimal aperture is 1.8 mm,1.6 mm,and 1.7 mm,respectively.The buffer hole can achieve a better-buffering effect in the range of variable pressure angle[0°,101°].The buffer hole structure can effectively alleviate the pressure shock and reduce the noise level,which lays a foundation for the design and theoretical research of hydraulic transformers.
文摘New design of plain flow distributor of the radial piston low speed hydraulic motor is presented. On the basis of analyzing its static mathematic model and structural optimization, the kinetic characteristics of the distribution plates and the oil film between them are discussed in detail.
文摘Based on turbulent theory, a 3D coupled model of fluid flow and solidification was built using finite difference method and used to study the influence of superheating degree and casting speed on fluid flow and solidification, analyze the interaction between shell and molten steel, and compare the temperature distribution under different technological conditions. The results indicate that high superheating degree can lengthen the liquid-core depth and make the crack and breakout possible, so suitable superheating should be controlled within 35℃ according to the simulation results. Casting speed which is one of the most important technological parameters of improving production rate, should be controlled between 0. 85 m/min and 1.05 m/min and the caster has great potential in the improvement of blank quality.