A Theoretical Study on Energy of a Gaseous System Vis-a-Vis Mass and Temperature

To study various properties of a gas has been a subject of rational curiosity in pneumatic sciences. A gaseous system, in general, is studied by using four measurable parameters namely, the pressure, volume, number of moles and temperature. In the present work, an attempt is made to study the variation of energy of an ideal gas with the two measurable parameters, the mass and temperature of the gas. Using the well known ideal gas equation, PV = nRT where symbols have their usual meanings and some simple mathematical operations widely used in physics, chemistry and mathematics in a transparent manner, an equation of state relating the three variables, the energy, mass and temperature of an ideal gas is obtained. It is found that energy of an ideal gas is equal to the product of mass and temperature of the gas. This gives a direct relationship between the energy, mass and temperature of the gas. Out of the three variables, the energy, mass and temperature of an ideal gas, if one of the parameters is held constant, the other two variables can be measured. At a constant temperature, when the power or energy is stabilized, the increase in the mass of the gas may affect the new works and an engine can therefore be prevented from overheating.

Characteristic Temperatures of Waxy Crude Oils

Gel point or pour point is widely used to evaluate the low temperature flowability of crude oil. However, it is not adequate to describe the gelling properties of waxy crude oils under flow conditions with gel point or pour point, since the theological behavior of crude oils is dependent on shear history. Waxy crude oils tend to gel at a low temperature. Based on gelation theory, the characteristic temperature of waxy crude oil was determined by analyzing viscosity-temperature data. Two mathematical models were developed for calculating characteristic temperatures of virgin crude oils and pour point depressants （PPD） beneficiated crude oils, respectively. By using these two models, the characteristic temperatures of crude oils that have experienced shearing and thermal histories can be predicted. The model for predicting the characteristic temperature of virgin crude oils has an average relative deviation of 4.5%, and all predicted values have a deviation within 2 ℃. Tested by 42 sets of data, the prediction model for crude oil treated with PPD has a high accuracy, with an average relative deviation of 4.2%, and 95.2 percent of predicted values have a deviation within 2 ℃. These two models provide useful ways for predicting the flowability of crude oils in pipelines when only wax content, wax appearance point and gel point are available.

Flow behaviour constitutive model of CuCrZr alloy and 35CrMo steel based on dynamic recrystallization softening effect under elevated temperature

In order to study the effect of dynamic recrystallization on the metal flow behavior during thermal deformation,the elevated temperature compression experiments of CuCrZr alloy and 35CrMo steel are carried out using Gleeble-3810 thermal simulator.It is proved that the samples underwent obvious dynamic recrystallization behavior during thermal deformation by microstructure observation of deformed specimens.The size of recrystallized grains increases as the temperature improved and the strain rate decreased.Meanwhile,the net softening rate caused by dynamic recrystallization is determined based on the stress-dislocation relationship.It can be found that the value of net softening rate increases quadratically as the Z parameter decreases,and the dynamic recrystallization net softening rate of CuCrZr alloy and 35CrMo steel are calculated to be 21.9%and 29.8%,respectively.Based on the dynamic recrystallization softening effect proposed,the novel elevated temperature flow constitutive models of two different alloys are proposed,and the related parameters are well defined and solved in detail.The predicted values of the obtained models are agreed well with the experimental values.

Temperature influence on macro-mechanics parameter of intact coal sample containing original gas from Baijiao Coal Mine in China

Investigation of temperature effect on mechanical parameters of coal is very important for understanding the mechanical response of coal bed at high temperature.It is especially benefcial for mitigating the thermal-induced disasters occurred in those coal mines suffering from heat hazard.In this work,coal samples,obtained from the No.2442 working face of Baijiao Coal Mine,were subjected to uniaxial compression ranging from 20 to 40℃ with an interval of 5℃.The apparatus used was designed to obtain deformation of a stressed sample,as well as the emission of gases desorbing from coal matrix.The adsorbed gas desorption caused by heating is measured during the entire testing.It is evident that the concentrations of releasing gas(containing methane,carbon dioxide and ethane)slightly rise with increasing temperature.Gas movement observed is closely related to the deformation of coal sample.Both uniaxial compressive strength and elastic modulus of coal samples tend to reduce with temperature.It reveals that increasing temperature can not only result in thermal expansion of coal,but also lead to desorption of preexisting gas in coal which can in turns harden coal due to shrinks of the coal matrix.Even though desorption of adsorbed gas can contribute to the hardening effect for the heated coal,by comparison to the results,it could be inferred that the softening of coal resulted from thermal expansion still predominates changes in mechanical characters of coal sample with temperature at the range from20 to 40℃.

Flow Field and Temperature Field in GaN-MOCVD Reactor Based on Computational Fluid Dynamics Modeling

Metal organic chenlical vapor deposition （AIOCVD） growth systems arc one of the. main types of equipment used for growing single crystal materials, such as GaN. To obtain fihn epitaxial materials with uniform performanee, the flow field and ternperature field in a GaN-MOCVD reactor are investigated by modeling and simulating. To make the simulation results more consistent with the actual situation, the gases in the reactor are considered to be compressible, making it possible to investigate the distributions of gas density and pressure in the reactor. The computational fluid dynamics method is used to stud,v the effects of inlet gas flow velocity, pressure in the reactor, rotational speed of graphite susceptor, and gases used in the growth, which has great guiding~ significance for the growth of GaN fihn materials.

Selective Area Growth and Characterization of GaN Nanorods Fabricated by Adjusting the Hydrogen Flow Rate and Growth Temperature with Metal Organic Chemical Vapor Deposition

CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen （H2）/nitrogen （N2） and growth temperature of the selective area growth （SAG） method with metal organic chemical vapor deposition （MOCVD）. The SAG template is obtained by nanospherical-lens photolithography. It is found that increasing the flow rate of 1-12 will change the CaN crystal shape from pyramid to vertical rod, while increasing the growth temperature will reduce the diameters of GaN rods to nanometer scale. Finally the CaN nanorods with smooth lateral surface and relatively good quality are obtained under the condition that the H2：N2 ratio is 1：1 and the growth temperature is 1030℃. The good crystal quality and orientation of GaN nanorods are confirmed by high resolution transmission electron microscopy. The cathodoluminescence spectrum suggests that the crystal and optical quality is also improved with increasing the temperature.

Numerical Investigation on the Flow and Temperature Fields in an Inductively Coupled Plasma Reactor

This paper gives a numerical study on the flow and temperature fields in an induced plasma reactor, which worked in 0.5 ATM with air as a working gas. We employed a two-dimensional mode of an inductively coupled plasma to calculate the temperature and flow field of the reactor as well as the generator. The algorithm is based on the solutions of the two-dimensional continuity, momentum, and energy equations in term of vorticity, stream function and enthalpy. An upwind finite-difference scheme was adopted to solve those equations with appropriate boundary conditions. The computed results show that there is a flat region with little parameter change in the reactor, that the diameter of the region is not much larger than that of the generator and that a deep change of parameter exists in the outer side of the region.

CONJUGATE MODEL FOR HEAT AND MASS TRANSFER OF POROUS WALL IN THE HIGH TEMPERATURE GAS FLOW

Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration and heat transfer equations in a porous body and boundary layer equations on its surface. Such an approach enables one to take into account complex interaction between heat and mass transfer in the gasdynamical flow and in the structure subjected to this flow. The main attention is given to the impact of the intraporous heat transfer intensity on the transpiration cooling efficiency.

Simulation of Temperature and Flow Field by Three Dimension Finite ElementMethod for Castex Process of AS Wire

Castex of AS wire is a new technology of near net shape. To study the variation of temperature and velocity of liquid (or semisolid) aluminum during dynamic solidification the numerical simulation was carried out with the theory of heat-transfer and hydrodynamics by means of 3-dimensional finite element method. From simulation results, it is found that the variation of temperature and velocityis mainly influenced by the casting temperature of aluminum, rotating speed of Castex wheel and flow of cooling water. Among theseinfluencing factors, the casting temperature distributes most to the length of liquid phase metal. Moreover, the faster the metal solidifies,the higher the metal there moves with the overall trend of descending from the bottom of the wheel to the shoe wall as well as from sidewalls to the center of wheel groove. In comparison with the practical value, the simulation is reliable.

Effect of heat flux and inlet temperature on the fouling characteristics of nanoparticles

In order to study the effect of heat flux and inlet temperature on the fouling characteristics of nanoparticles, and to further reveal the fouling mechanism for insights into proper operating conditions, γ-Al_2O_3/water suspensions were chosen as the subject of this research. The particulate fouling characteristics of γ-Al_2O_3/water suspensions on the surface of stainless steel have been experimentally studied by varying the heat flux and the inlet temperature under single-phase flow and subcooled-flow boiling conditions. The results show that in the condition of single-phase flow, the asymptotic value of fouling resistance decreases with increasing of heat flux and inlet temperature. The asymptotic value of fouling resistance under single-phase flow is much higher than for the subcooled-flow boiling condition. The effect of heat flux on the fouling resistance under the two flow states has an inverse relationship, and there exists a minimum value of fouling resistance between these two states. For subcooled-flow boiling, the asymptotic value of fouling resistance increases with increasing heat flux, whereas the effect on fouling resistance by the inlet temperature is negligible.

NUMERICAL SIMULATION OF MOLTEN POOL AND CONTROL STRATEGY OF KISS POINT IN A TWIN-ROLL STRIP CASTING PROCESS

Coupled turbulent flow, temperature fields of the twin-roll casting strip process were simulated by three-dimensional finite element method. Based on the heat balance calculation and using inverse methods between the simulations and real experiments, the relational models among casting speed, location, and coefficient of heat transfer between molten metal and rolls in different regions are given. In the simulation, the calculated surface temperatures are in good agreement with the measured values. An on-line model of kiss point is derived by simulations and the geometry of molten pool, corresponding control strategy is also proposed.

3D Numerical Analysis of the Arc Plasma Behavior in a Submerged DC Electric Arc Furnace for the Production of Fused MgO

A three dimensional steady-state magnetohydrodynamic model is developed for the arc plasma in a DC submerged electric arc furnace for the production of fused MgO. The arc is generated in a small semi-enclosed space formed by the graphite electrode, the molten bath and unmelted raw materials. The model is first used to solve a similar problem in a steel making furnace, and the calculated results are found to be in good agreement with the published measurements. The behavior of arcs with different arc lengths is also studied in the furnace for MgO production. From the distribution of the arc pressure on the bath surface it is shown that the arc plasma impingement is large enough to cause a crater-like depression on the surface of the MgO bath. The circulation of the high temperature air under the electrode may enhance the arc efficiency, especially for a shorter arc.

NUMERICAL SIMULATION BY COMPUTATIONAL FLUID DYNAMICS AND EXPERIMENTAL STUDY ON STIRRED BIOREACTOR WITH PUNCHED IMPELLER

Instantaneous flow field and temperature field of the two-phase fluid are measured by particle image velocimetry （PIV） and steady state method during the state of onflow. A turbulent two-phase fluid model of stirred bioreactor with punched impeller is established by the computational fluid dynamics （CFD）, using a rotating coordinate system and sliding mesh to describe the relative motion between impeller and baffles. The simulation and experiment results of flow and temperature field prove their warps are less than 10% and the mathematic model can well simulate the fields, which will also provide the study on optimized-design and scale-up of bioreactors with reference value.

Structure and Combustion Characteristics of Methane/Air Premixed Flame under the Action of Wall

In order to obtain the combustion characteristics of the CH4/Air premixed flame under the action of the wall interaction,a study on the impact of the jet flame on the wall at different separation distances was carried out.The separation distance from the burner outlet to the lower surface of the wall is changed and the flame structure is obtained through experiments.The temperature,velocity and reaction rate are obtained through numerical simulation,and the law of flame characteristics change is obtained through analysis.The results show that as the separation distance increases,the premixing cone inside the flame gradually changes from a horn shape to a complete cone shape and the length of the premixing cone profile increases.Also,the peak temperature and velocity of the mixture in the axial direction gradually increase,and the temperature and velocity in the radial direction first increase and then decrease.The temperature gradient and velocity reach the maximum when the separation distance is 11 mm.The peaks of reactants(CH_(4))net reaction rate intermediate products(CO)and products(CO_(2),H_(2)O)on the axis and the axial distance corresponding to the peaks increase accordingly.The chemical reaction rate near the wall also gradually decreases with the increase of the separation distance.

Effect of tempering temperature on strain hardening exponent and flow stress curve of 1000MPa grade steel for construction machinery

To study the effect of tempering temperature on strain hardening exponent and flow stress curve,one kind of 1000 MPa grade low carbon bainitic steel for construction machinery was designed,and the standard uniaxial tensile tests were conducted at room temperature.A new flow stress model,which could predict the flow behavior of the tested steels at different tempering temperatures more efficiently,was established.The relationship between mobile dislocation density and strain hardening exponent was discussed based on the dislocation-stress relation.Arrhenius equation and an inverse proportional function were adopted to describe the mobile dislocation,and two mathematical models were established to describe the relationship between tempering temperature and strain hardening exponent.Nonlinear regression analysis was applied to the Arrhenius type model,hence,the activation energy was determined to be 37.6kJ/mol.Moreover,the square of correlation coefficient was 0.985,which indicated a high reliability between the fitted curve and experimental data.By comparison with the Arrhenius type curve,the general trend of the inverse proportional fitting curve was coincided with the experimental data points except of some fitting errors.Thus,the Arrhenius type model can be adopted to predict the strain hardening exponent at different tempering temperatures.

Propagation of sound in pipes with gas flow of high temperature

In this paper, propagation of sound in pipes under the influence of a gas flow of high temperature is investigated . The analysis in the paper is based on the fundamental equations of fluid mechanics . Approximate formulas of the variation of parameters, such as the static tempera -ture, the local velocity of sound , the flow speed and the Mach number, with distance are obtained . The four parameters transmision matix which determines the acoustical character of the pipe is derived and discussed . The acoustical character of a pulsating gas heater is investigated experimentally and theoretically . The theoretical values of the resonant frequencies of the device are in good agreement with the experimental results.

Conjugate heat transfer investigations of turbine vane based on transition models

The accurate simulation of boundary layer transition process plays a very important role in the prediction of turbine blade temperature field. Based on the Abu-Ghannam and Shaw （AGS） and c-Re h transition models, a 3D conjugate heat transfer solver is developed, where the fluid domain is discretized by multi-block structured grids, and the solid domain is discretized by unstructured grids. At the unmatched fluid/solid interface, the shape function interpolation method is adopted to ensure the conservation of the interfacial heat flux. Then the shear stress transport （SST） model, SST ＆ AGS model and SST ＆ c-Re h model are used to investigate the flow and heat transfer characteristics of Mark II turbine vane. The results indicate that compared with the full turbulence model （SST model）, the transition models could improve the prediction accuracy of temperature and heat transfer coefficient at the laminar zone near the blade leading edge. Compared with the AGS transition model, the c-Re h model could predict the transition onset location induced by shock/boundary layer interaction more accurately, and the prediction accuracy of temperature field could be greatly improved.

Numerical Analysis of Flow Instability in the Water Wall of a Supercritical CFB Boiler with Annular Furnace

In order to expand the study on flow instability of supercritical circulating fluidized bed(CFB) boiler,a new numerical computational model considering the heat storage of the tube wall metal was presented in this paper.The lumped parameter method was proposed for wall temperature calculation and the single channel model was adopted for the analysis of flow instability.Based on the time-domain method,a new numerical computational program suitable for the analysis of flow instability in the water wall of supercritical CFB boiler with annular furnace was established.To verify the code,calculation results were respectively compared with data of commercial software.According to the comparisons,the new code was proved to be reasonable and accurate for practical engineering application in analysis of flow instability.Based on the new program,the flow instability of supercritical CFB boiler with annular furnace was simulated by time-domain method.When 1.2 times heat load disturbance was applied on the loop,results showed that the inlet flow rate,outlet flow rate and wall temperature fluctuated with time eventually remained at constant values,suggesting that the hydrodynamic flow was stable.The results also showed that in the case of considering the heat storage,the flow in the water wall is easier to return to stable state than without considering heat storage.

Numerical investigation of thermo-physical properties of non-newtonian fliud in a modelled intestine

Several kinds of researches have been conducted on peristaltic flow of non-Newtonian fluid in modelled oesophagus,stomach and intestine.However,further investigation is still needed es-pecially in the area of mechanical shear stress,the influence of inlet temperature and velocity,Nutsselt number and the history of strain rates experienced by fluid particles.This study presents the numerical investigation of thermo-physical properties of non-Newtonian fluid in a modelled intestine.The properties investigated were fluid temperature,velocity,Nutsselt number and wall shear stress.Numerical simulation was performed by solving 3D Navier-Stokes and continuity equations.The intestinal model was drawn by using Autodesk Inventor 2017 while the numerical investigation was conducted by using ANSYS FLUENT 16.0.The Computational Fluid Dynamics solver employs the Finite Element Method(FEM)to discretize the governing equations.Chyme,Hibiscus Sabdariffa Roselle(Sobo),Soymilk(Soya)and Pap(Ogi)were the working fluids used for the investigation.Analyses of the results showed that the variation of fluid temperature and heat transfer with axial position across the length of intestinal model were not significantly influenced by the variation of the inlet velocity.Expansion of the model about the pulsating part enhanced heat transfer and nutrient delivery to the intestinal walls.Variation of the inlet velocity did not affect the average Nutsselt number.Chyme and Sobo had the highest and lowest Nutsselt number,respectively.Sobo displayed the best fluid properties considering flow behaviour while Soya dis-played the best properties for thermal history.The results presented in this study are of countless importance in medical,paramedical,engineering applications,thermoregulation system,ther-motherapy,and biomedical disciplines,where analyses and investigation of gastrointestinal tract history can be understudied.