Experiments on simultaneous absorption of SO_2 and NO_X from sintering flue gas via a composite absorbent NaClO_2/NaClO were carried out. The effects of various operating parameters such as NaClO_2 concentration(ms), ...Experiments on simultaneous absorption of SO_2 and NO_X from sintering flue gas via a composite absorbent NaClO_2/NaClO were carried out. The effects of various operating parameters such as NaClO_2 concentration(ms), NaClO concentration(mp), molar ratio of NaClO_2/NaClO(M), solution temperature(TR), initial solution pH, gas flow(Vg) and inlet concentration of SO_2(CS) and NO(CN) on the removal efficiencies of SO_2 and NO were discussed. The optimal experimental conditions were determined to be initial solution pH = 6, TR=55 °C and M = 1.3 under which the average efficiencies of desulfurization and denitrification could reach99.7% and 90.8%, respectively. Moreover, according to the analysis of reaction products, it was found that adding NaClO to NaClO_2 aqueous solution is favorable for the generation of ClO_2 and Cl_2 which have significant effect on desulfurization and denitrification. Finally, engineering experiments were performed and obtained good results demonstrating that this method is practicable and promising.展开更多
With the vigorous development of China's iron and steel industry and the introduction of ultra-low emission policies,the emission of pollutants such as SO_(2)and NO x has received unprecedented attention.Consideri...With the vigorous development of China's iron and steel industry and the introduction of ultra-low emission policies,the emission of pollutants such as SO_(2)and NO x has received unprecedented attention.Considering the increase of the proportion of semi-dry desulfurization technology in the desulfurization process,several semi-dry desulphurization technologies such as flue gas circulating fluidized bed(CFB),dense flow absorber(DFA)and spray drying absorption(SDA)are briefly summarized.Moreover,a method for simultaneous treatment of SO_(2)and NOx in sintering/pelletizing flue gas by O_(3)oxidation combined with semidry method is introduced.Meantime,the effects of key parameters such as O_(3)/NO molar ratio,Ca SO_(3),SO_(2),reaction temperature,Ca/(S+2 N)molar ratio,droplet size and approach to adiabatic saturation temperature(AAST)on denitrification and desulfurization are analyzed.Furthermore,the reaction mechanism of denitrification and desulfurization is further elucidated.Finally,the advantages and development prospects of the new technology are proposed.展开更多
The low-temperature wet oxidation behavior of semi-dry desulfurization ash from iron ore sintering flue gas in ammonium citrate solution was investigated for efficiently utilizing the low-quality desulfurization ash. ...The low-temperature wet oxidation behavior of semi-dry desulfurization ash from iron ore sintering flue gas in ammonium citrate solution was investigated for efficiently utilizing the low-quality desulfurization ash. The effects of the ammonium citrate concentration, oxidation temperature, solid/liquid ratio, and oxidation time on the wet oxidation behavior of desulfurization ash were studied. Simultaneously, the oxidation mechanism of desulfurization ash was revealed by means of X-ray diffraction, Zeta electric resistance, and X-ray photoelectron spectroscopy (XPS) analysis. Under the optimal conditions with ammonium citrate, the oxidation ratio of CaSO_(3) was up to the maximum value (98.49%), while that of CaSO_(3) was only 8.92% without ammonium citrate. Zeta electric resistance and XPS results indicate that the dissolution process of CaSO_(3) could be significantly promoted by complexation derived from the ammonium citrate hydrolysis. As a result, the oxidation process of CaSO_(3) was transformed from particle oxidation to SO_(3)^(2−) ion oxidation, realizing the rapid transformation of desulfurization ash from CaSO_(3) to CaSO_(4) at low temperature. It provides a reference for the application of semi-dry desulfurization ash and contributes to sustainable management for semi-dry desulfurization ash.展开更多
The properties of activated coke(AC)for sintering flue gas purification greatly affect the efficiency of desulfurization and denitration,but they gradually change during cycles.The change in properties of coal-based A...The properties of activated coke(AC)for sintering flue gas purification greatly affect the efficiency of desulfurization and denitration,but they gradually change during cycles.The change in properties of coal-based AC during cycles was studied to clarify the change law and AC optimization index.The AC oxygen content rapidly increases 13.49 to 17.87 wt.%in the early cycles to form phenol,which promotes the denitration rate 55.63%to 78.20%.The denitration performance slowly increases in subsequent cycles becaof the generation of quinone AC slow oxidation.However,the oxygen-containing groups are not conducive to adsorption capacity of AC for NO.The adsorbed NO species which can be replaced SO2 is the main NO species on AC,and its amount decreases with the decrease in CC content of AC.The AC chemical loss leads to the opening of closed pores,expansion of original pores and formation of new pores,causing micropore volume to increase 0.085%to 0.152%,compressive strength to decrease 472 to 336 N,and abrasive resistance to decrease 97.87%to 94.16%during cycles.The low oxygen content and high micropore volume are favorable to the initial desulfurization performance,and the former is more decisive.After a while,the desulfurization rate is linearly positively correlated with the micropore volume regardless of the chemistry.4-h desulfurization rate increased 69.03%to 85.91%during 25 cycles due to the increasing micropore volume.The AC properties change in cycles will greatly affect the desulfurization and denitration rate in the height direction of the flue gas purification system.Selecting the coal-based AC with moderate micropore volume,easy oxidation surface and less original oxygen-containing groups facilitates the better purification efficiency at lower cost for sintering plants.展开更多
Modification of metallurgical coke,biomass char and semi-coke was carried out using a microwave device with power of 450-850 W and irradiation time of 6-12 min.The desulfurization rates of three carbon materials befor...Modification of metallurgical coke,biomass char and semi-coke was carried out using a microwave device with power of 450-850 W and irradiation time of 6-12 min.The desulfurization rates of three carbon materials before and after modification were tested.The effects of microwave power and irradiation time on the pore texture and surface chemical characteristics of the three carbon materials were examined by SEM,BET and Fourier transform infrared spectroscopy（FTIR）.The results showed that the specific surface area,total pore volume and pore diameter of biomass char and semi-coke after irradiation decreased slightly.Noteworthily,the pore diameter turned small and the acidic functional groups on their surface decomposed,thereby the basicity of carbon surface increased by microwave modification.The optimal promotion of desulfurization rate of three carbon materials was semi-coke irradiated at 850 W for 9 min and the sulfur dioxide adsorption rate was up to 45%.展开更多
At present,the continuous accumulation of the flue gas desulfurization(FGD)gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel...At present,the continuous accumulation of the flue gas desulfurization(FGD)gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel industry,it is significant to improve the usage of by-product gypsum.Employing the sintering FGD gypsum,ferric oxide,and graphite carbon as raw materials,the effects of the carbon content,reaction time,and molar ratio of CaO to Fe_(2)O_(3)on the desulfurization rate of gypsum were studied based on the orthogonal experiment.The results show that the order of the three influencing factors on the desulfurization rate of FGD gypsum is:molar ratio of CaO to Fe_(2)O_(3)>reaction time>carbon content.Under the optimal conditions of 20 wt.%carbon content,4 h reaction time,and 1:1 molar ratio of CaO to Fe_(2)O_(3),the desulfurization rate of desulfurization gypsum is 95.79%,and 97.57 wt.%of calcium ferrite appears in the solid product,which can be used as sintering additive to increase the economic benefits of enterprises and realize the green ecological development mode of internal generation and internal digestion of solid waste in iron and steel enterprises.展开更多
基金Supported by the National Science Foundation of China for Distinguished Young Scholars(No.51325601)Major Program of National Science Foundation of China(No.51390492)Joint Funds of National Science Foundation of China(No.U1560205)
文摘Experiments on simultaneous absorption of SO_2 and NO_X from sintering flue gas via a composite absorbent NaClO_2/NaClO were carried out. The effects of various operating parameters such as NaClO_2 concentration(ms), NaClO concentration(mp), molar ratio of NaClO_2/NaClO(M), solution temperature(TR), initial solution pH, gas flow(Vg) and inlet concentration of SO_2(CS) and NO(CN) on the removal efficiencies of SO_2 and NO were discussed. The optimal experimental conditions were determined to be initial solution pH = 6, TR=55 °C and M = 1.3 under which the average efficiencies of desulfurization and denitrification could reach99.7% and 90.8%, respectively. Moreover, according to the analysis of reaction products, it was found that adding NaClO to NaClO_2 aqueous solution is favorable for the generation of ClO_2 and Cl_2 which have significant effect on desulfurization and denitrification. Finally, engineering experiments were performed and obtained good results demonstrating that this method is practicable and promising.
基金supported by the National Key Research and Development Program of China(No.2017YFC0210600)the National Natural Science Foundation of China(No.51978644)。
文摘With the vigorous development of China's iron and steel industry and the introduction of ultra-low emission policies,the emission of pollutants such as SO_(2)and NO x has received unprecedented attention.Considering the increase of the proportion of semi-dry desulfurization technology in the desulfurization process,several semi-dry desulphurization technologies such as flue gas circulating fluidized bed(CFB),dense flow absorber(DFA)and spray drying absorption(SDA)are briefly summarized.Moreover,a method for simultaneous treatment of SO_(2)and NOx in sintering/pelletizing flue gas by O_(3)oxidation combined with semidry method is introduced.Meantime,the effects of key parameters such as O_(3)/NO molar ratio,Ca SO_(3),SO_(2),reaction temperature,Ca/(S+2 N)molar ratio,droplet size and approach to adiabatic saturation temperature(AAST)on denitrification and desulfurization are analyzed.Furthermore,the reaction mechanism of denitrification and desulfurization is further elucidated.Finally,the advantages and development prospects of the new technology are proposed.
基金the National Natural Science Foundation of China(NSFC)(Grant Nos.51704004 and 51674002)the Natural Science Foundation of Anhui Province(Grant No.1808085QE133).
文摘The low-temperature wet oxidation behavior of semi-dry desulfurization ash from iron ore sintering flue gas in ammonium citrate solution was investigated for efficiently utilizing the low-quality desulfurization ash. The effects of the ammonium citrate concentration, oxidation temperature, solid/liquid ratio, and oxidation time on the wet oxidation behavior of desulfurization ash were studied. Simultaneously, the oxidation mechanism of desulfurization ash was revealed by means of X-ray diffraction, Zeta electric resistance, and X-ray photoelectron spectroscopy (XPS) analysis. Under the optimal conditions with ammonium citrate, the oxidation ratio of CaSO_(3) was up to the maximum value (98.49%), while that of CaSO_(3) was only 8.92% without ammonium citrate. Zeta electric resistance and XPS results indicate that the dissolution process of CaSO_(3) could be significantly promoted by complexation derived from the ammonium citrate hydrolysis. As a result, the oxidation process of CaSO_(3) was transformed from particle oxidation to SO_(3)^(2−) ion oxidation, realizing the rapid transformation of desulfurization ash from CaSO_(3) to CaSO_(4) at low temperature. It provides a reference for the application of semi-dry desulfurization ash and contributes to sustainable management for semi-dry desulfurization ash.
基金the financial support of Fundamental Research Funds for the Central Universities(Grant No.FRF-IC-18-010).
文摘The properties of activated coke(AC)for sintering flue gas purification greatly affect the efficiency of desulfurization and denitration,but they gradually change during cycles.The change in properties of coal-based AC during cycles was studied to clarify the change law and AC optimization index.The AC oxygen content rapidly increases 13.49 to 17.87 wt.%in the early cycles to form phenol,which promotes the denitration rate 55.63%to 78.20%.The denitration performance slowly increases in subsequent cycles becaof the generation of quinone AC slow oxidation.However,the oxygen-containing groups are not conducive to adsorption capacity of AC for NO.The adsorbed NO species which can be replaced SO2 is the main NO species on AC,and its amount decreases with the decrease in CC content of AC.The AC chemical loss leads to the opening of closed pores,expansion of original pores and formation of new pores,causing micropore volume to increase 0.085%to 0.152%,compressive strength to decrease 472 to 336 N,and abrasive resistance to decrease 97.87%to 94.16%during cycles.The low oxygen content and high micropore volume are favorable to the initial desulfurization performance,and the former is more decisive.After a while,the desulfurization rate is linearly positively correlated with the micropore volume regardless of the chemistry.4-h desulfurization rate increased 69.03%to 85.91%during 25 cycles due to the increasing micropore volume.The AC properties change in cycles will greatly affect the desulfurization and denitration rate in the height direction of the flue gas purification system.Selecting the coal-based AC with moderate micropore volume,easy oxidation surface and less original oxygen-containing groups facilitates the better purification efficiency at lower cost for sintering plants.
基金the National Natural Science Foundation of China(No.51604048)Fund of Chongqing Science and Technology(Nos.cstc2015shmszx20016 and cstc2016shmszx20015)China Postdoctoral Science Foundation(2016M590862)
文摘Modification of metallurgical coke,biomass char and semi-coke was carried out using a microwave device with power of 450-850 W and irradiation time of 6-12 min.The desulfurization rates of three carbon materials before and after modification were tested.The effects of microwave power and irradiation time on the pore texture and surface chemical characteristics of the three carbon materials were examined by SEM,BET and Fourier transform infrared spectroscopy（FTIR）.The results showed that the specific surface area,total pore volume and pore diameter of biomass char and semi-coke after irradiation decreased slightly.Noteworthily,the pore diameter turned small and the acidic functional groups on their surface decomposed,thereby the basicity of carbon surface increased by microwave modification.The optimal promotion of desulfurization rate of three carbon materials was semi-coke irradiated at 850 W for 9 min and the sulfur dioxide adsorption rate was up to 45%.
基金Fundamental Research Funds for the Central Universities(FRF-MP-20-018).
文摘At present,the continuous accumulation of the flue gas desulfurization(FGD)gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel industry,it is significant to improve the usage of by-product gypsum.Employing the sintering FGD gypsum,ferric oxide,and graphite carbon as raw materials,the effects of the carbon content,reaction time,and molar ratio of CaO to Fe_(2)O_(3)on the desulfurization rate of gypsum were studied based on the orthogonal experiment.The results show that the order of the three influencing factors on the desulfurization rate of FGD gypsum is:molar ratio of CaO to Fe_(2)O_(3)>reaction time>carbon content.Under the optimal conditions of 20 wt.%carbon content,4 h reaction time,and 1:1 molar ratio of CaO to Fe_(2)O_(3),the desulfurization rate of desulfurization gypsum is 95.79%,and 97.57 wt.%of calcium ferrite appears in the solid product,which can be used as sintering additive to increase the economic benefits of enterprises and realize the green ecological development mode of internal generation and internal digestion of solid waste in iron and steel enterprises.
