Simulation investigation on fluid characteristics of jet pipe water hydraulic servo valve based on CFD

Simulation investigation on fluid characteristics of the water hydraulic jet pipe servo valve （WHJPSV） is conducted through a commercial computational fluid dynamics （CFD） software package FLUENT. In particular, the factors to fluid characteristics of WHJPSV are addressed, which include diameter combination of jet pipe and receiver pipe, jet pipe nozzle clearance, angle between two jet receiver pipes and deflection angle of the jet pipe. It is concluded from the results that： （i） Structural parameters have great influences on fluid characteristics of WHJPSV, when d1 = d2 = 0.3 mm, α= 45 , b = 0.5 mm, and the simulation exhibits better fluid characteristics; （ii） The magnitude of the recovery pressure and flow velocity increase almost linearly with the deflection angle of jet pipe. The research work in this paper is important for determining and optimizing the structural parameters of the jet pipe and jet receiver. The relevant conclusions could be extended to the study of other water hydraulic servo control components.

Ore-forming fluid characteristics and ore-forming materials source of the Tudimiaogou – Yindongshan lead-zinc polymetallic orefield, west Henan

1 Introduction The Tudimiaogou-Yindongshan lead-zinc polymetallic orefield is located in the Tudimiaogou-Weimoshi lead and zinc silver polymetallic metallogenic belt.The belt is an important part of southwestern Henan lead and zinc

Characteristics and mechanism of smart fluid for sweep-controlling during CO_(2) flooding

A smart response fluid was designed and developed to overcome the challenges of gas channeling during CO_(2)flooding in low-permeability,tight oil reservoirs.The fluid is based on Gemini surfactant with self-assembly capabilities,and the tertiary amine group serves as the response component.The responsive characteristics and corresponding mechanism of the smart fluid during the interaction with CO_(2)/oil were studied,followed by the shear characteristics of the thickened aggregates obtained by the smart fluid responding to CO_(2).The temperature and salt resistance of the smart fluid and the aggregates were evaluated,and their feasibility and effectiveness in sweep-controlling during the CO_(2)flooding were confirmed.This research reveals:(1)Thickened aggregates could be assembled since the smart fluid interacted with CO_(2).When the mass fraction of the smart fluid ranged from 0.05%to 2.50%,the thickening ratio changed from 9 to 246,with viscosity reaching 13 to 3100 mPas.As a result,the sweep efficiency in low-permeability core models could be increased in our experiments.(2)When the smart fluid(0.5%to 1.0%)was exposed to simulated oil,the oil/fluid interfacial tension decreased to the level of 1×10^(-2)mN/m.Furthermore,the vesicle-like micelles in the smart fluid completely transformed into spherical micelles when the fluid was exposed to simulated oil with the saturation greater than 10%.As a result,the smart fluid could maintain low oil/fluid interfacial tension,and would not be thickened after oil exposure.(3)When the smart fluid interacted with CO_(2),the aggregates showed self-healing properties in terms of shear-thinning,static-thickening,and structural integrity after several shear-static cycles.Therefore,this fluid is safe to be placed in deep reservoirs.(4)The long-term temperature and salt resistance of the smart fluid and thickened aggregates have been confirmed.

Characteristics of Abnormal Pressure Systems and Their Responses of Fluid in Huatugou Oil Field,Qaidam Basin

Based on the comprehensive study of core samples, well testing data, and reservoir fluid properties, the construction and the distribution of the abnormal pressure systems of the Huatugou oil field in Qaidam Basin are discussed. The correlation between the pressure systems and hydrocarbon accumulation is addressed by analyzing the corresponding fluid characteristics. The results show that the Huatugou oil field as a whole has low formation pressure and low fluid energy; therefore, the hydrocarbons are hard to migrate, which facilitates the forming of primary reservoirs. The study reservoirs, located at the Xiayoushashan Formation （N1/2） and the Shangganchaigou Formation （N1） are relatively shallow and have medium porosity and low permeability. They are abnormal low-pressure reservoirs with an average formation pressure coefficient of 0.61 and 0.72 respectively. According to the pressure coefficient and geothermal anomaly, the N1 and N1/2 Formations belong to two independent temperature-pressure systems, and the former has slightly higher energy. The low-pressure compartments consist of a distal bar as the main body, prodelta mud as the top boundary, and shore and shallow lake mud or algal mound as the bottom boundary. They are vertically overlapped and horizontally paralleled. The formation water is abundant in the Cl^- ion and can be categorized as CaCl2 type with high safinity, which indicates that the abnormal low-pressure compartments are in good sealing condition and beneficial for oil and gas accumulation and preservation.

Uniformity evaluation and optimization of fluid flow characteristics in a seven-strand tundish

The effect of flow control devices（FCDs） on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1：2.5 hydraulic model and a numerical simulation of a 1：1 geometric model.The variation coefficient（CV） was defined to evaluate the flow uniformity of the seven-strand tundish.An optimized FCD configuration was proposed on the basis of the evaluation of experimental results.It is concluded that a turbulence inhibitor（TI） and U-type dam are essential to improve the uniformity of fluid flow in the seven-strand tundish.In addition,the configuration of inclination T-type dams with a height of 200 mm between the second and third strands and with a height of 300 mm between the third and fourth strands can minimize the proportion of dead zone.After optimizing the configuration of FCDs,the variation coefficient reduces below 20%of the mean value,and the average proportion of dead zone is just 14.6%;in addition,the temperature fluctuation between the strands could be controlled within 0.6 K.In summary,the uniformity of flow and temperature in the seven-strand tundish is greatly improved.

Geochemical Characteristics of the Ore-forming Fluids of the Haigou Gold Deposit, Jilin

The quartz in the Haigou gold deposit contains a great abundance of three-phase CO2-NaCl-H2O and two-phase CO2-rich inclusions, which are associated with two-phase NaCl-H2O ones. The ore-forming fluids, which were rich in CO2, are classified into two types with two different sources: the high-salinity CO2-rich NaCl-H2O fluid derived from magmatic hydrothermal solution, and the low-salinity NaCl-H2O fluid from ancient meteoric water. The optimum conditions for gold mineralization are 220-300℃ for the temperature, 4-20 MPa for the fluid static pressure, 1-3 km for the mineralization depth, 2-7 w (NaCl)/10-2 for the fluid salinity, and 0.644 g/cm3 for the total density. The fluid was in a critical or supercritical state at the initial stage of mineralization, and it boiled and was unmixed with CO2 and NaCl-H2O in the climax of mineralization, leading to the decomposition of Au-chlorine complexes and the bulk precipitation of Au.The type, association, homogenization temperature and composition (CO2/H2O value etc.) are the microscopic criteria for distinguishing the auriferous quartz vein from the barren quartz

Geochemical Characteristics of the Fluid Inclusions Trapped in Primary Gypsum of the Lop Nor Basin

Objective The Lop Nor Basin is a very important Quaternary potash-formation basin in China. It is a typical sulphate- potash brine mine with an average grade of 1.4% （KC1） in underground concentrated brines. It is extraordinary that the reservoir of potassium-rich brines is glauberite stratum rather than halite rock. The anomalous potassium enrichment, advanced in relative early stage of lake evolution （sulphate stage）, has attracted much attention in the recent twenty years. Many researchers consider that there may be other source supply besides the Tarim River.

Characteristics of the ore-forming fluid in the Huayuan Pb-Zn ore filed, Northwest of Hunan Province, China

1 Geological Setting The Huayuan Pb-Zn ore field in Xiangxi is located in the southeastern margin of the Yangtze block and the mid-segment of the West Hunan-West Hubei metallogenic belt.The exposed stratum are the lower

Entropy Production Analysis for Hump Characteristics of a Pump Turbine Model

The hump characteristic is one of the main problems for the stable operation of pump turbines in pump mode.However,traditional methods cannot reflect directly the energy dissipation in the hump region.In this paper,3D simulations are carried out using the SST k-ω turbulence model in pump mode under different guide vane openings.The numerical results agree with the experimental data.The entropy production theory is introduced to determine the flow losses in the whole passage,based on the numerical simulation.The variation of entropy production under different guide vane openings is presented.The results show that entropy production appears to be a wave,with peaks under different guide vane openings,which correspond to wave troughs in the external characteristic curves.Entropy production mainly happens in the runner,guide vanes and stay vanes for a pump turbine in pump mode.Finally,entropy production rate distribution in the runner,guide vanes and stay vanes is analyzed for four points under the 18 mm guide vane opening in the hump region.The analysis indicates that the losses of the runner and guide vanes lead to hump characteristics.In addition,the losses mainly occur in the runner inlet near the band and on the suction surface of the blades.In the guide vanes and stay vanes,the losses come from pressure surface of the guide vanes and the wake effects of the vanes.A new insight-entropy production analysis is carried out in this paper in order to find the causes of hump characteristics in a pump turbine,and it could provide some basic theoretical guidance for the loss analysis of hydraulic machinery.

Mathematical Model of Steady State Operation in Jet Pipe Electro-Hydraulic Servo Valve

Jet pipe electro-hydraulic servo valve is the heart of feedback control systems,and it is one of the mechatronic components used for precision flow control application.It consists of several precision and ddicate components.The performance of the jet pipe servo valve depends on many parameters.During the developmental stage,it is very difficult to ascertain the function parameters.The steady-state analysis of jet pipe electro-hydraulic servo valve has been made to simulate its fluid characteristics （flowin,flow-out,leakage flow,recovery or load pressure,etc.） by mathematical modeling.Theoretical model was conducted on various affecting parameters on the pressure,the main flow rate of fluid,or leakage flow through the receiver holes.The major parameters studied are jet pipe nozzle diameters,receiver hole diameters,angle between the two centre-lines of receiver hole,nozzle offset,and nozzle stand-of distance.In this paper the research is important to determine and optimize the structural parameters of jet pipe servo valve.Thus,equations of the pressure and flow characteristics are set up and the optimal structural parameters of jet pipe are established.

Computational fluid dynamic modeling of gas flow characteristics of the high-power CW CO_2 laser

To increase the photoelectronic conversion efficiency of the single discharge tube and to meet the requirements of the laser cutting system, optimization of the discharge tube structure and gas flow field is necessary. We present a computational fluid dynamic model to predict the gas flow characteristics of high-power fast-axial flow CO2 laser. A set of differential equations is used to describe the operation of the laser. Gas flow characteristics, are calculated. The effects of gas velocity and turbulence intensity on discharge stability are studied. Computational results are compared with experimental values, and a good agreement is observed. The method presented and the results obtained can make the design process more efficient.

Recovery of rare and precious metals from urban mines —— A review

Urban mining is essential for continued natural resource extraction. The recovery of rare and precious metals （RPMs） from urban mines has attracted increasing attention from both academic and industrial sectors, because of the broad application and high price of RPMs, and their low content in natural ores. This study summarizes the distribution characteristics of various RPMs in urban mines, and the advantages and shortcomings of various technologies for RPM recovery from urban mines, including both conventional （pyrometallurgical, hydrometallurgical, and biometallurgical processing）, and emerging （electrochemical, supereritieal fluid, mechanochemical, and ionic liquids processing） technologies. Mechanical/physical technologies are commonly employed to separate RPMs from nonmetallic components in a pre-treatment process. A pyrometallurgical process is often used tbr RPM recovery, although the expensive equipment required has limited its use in small and medium-sized enterprises. Hydrometallurgical processing is effective and easy to operate, with high selectivity of target metals and high recovery efficiency of RPMs, compared to pyrometallurgy. Biometallurgy, though, has shown the most promise for leaching RPMs from urban mines, because of its low cost and environmental friendliness. Newly developed technologies electrochemical, supercritical fluid, ionic liquid, and mechanochemical have offered new choices and achieved some success in laboratory experiments, especially as efficient and environmentally friendly methods of recycling RPMs. With continuing advances in science and technology, more technologies will no doubt be developed in this field, and be able to contribute to the sustainability of RPM mining.