Optimization method of fracturing fluid volume intensity for SRV fracturing technique in shale oil reservoir based on forced imbibition:A case study of well X-1 in Biyang Sag of Nanxiang Basin,China

An optimization method of fracturing fluid volume strength was introduced taking well X-1 in Biyang Sag of Nanxiang Basin as an example.The characteristic curves of capillary pressure and relative permeability were obtained from history matching between forced imbibition experimental data and core-scale reservoir simulation results and taken into a large scale reservoir model to mimic the forced imbibition behavior during the well shut-in period after fracturing.The optimization of the stimulated reservoir volume(SRV)fracturing fluid volume strength should meet the requirements of estimated ultimate recovery(EUR),increased oil recovery by forced imbibition and enhancement of formation pressure and the fluid volume strength of fracturing fluid should be controlled around a critical value to avoid either insufficiency of imbibition displacement caused by insufficient fluid amount or increase of costs and potential formation damage caused by excessive fluid amount.Reservoir simulation results showed that SRV fracturing fluid volume strength positively correlated with single-well EUR and an optimal fluid volume strength existed,above which the single-well EUR increase rate kept decreasing.An optimized increase of SRV fracturing fluid volume and shut-in time would effectively increase the formation pressure and enhance well production.Field test results of well X-1 proved the practicality of established optimization method of SRV fracturing fluid volume strength on significant enhancement of shale oil well production.

Impact of Pollutant Concentration and Particle Deposition on the Radiative Flow of Casson-Micropolar Fluid between Parallel Plates

Assessing the behaviour and concentration of waste pollutants deposited between two parallel plates is essential for effective environmental management.Determining the effectiveness of treatment methods in reducing pollution scales is made easier by analysing waste discharge concentrations.The waste discharge concentration analysis is useful for assessing how effectively wastewater treatment techniques reduce pollution levels.This study aims to explore the Casson micropolar fluid flow through two parallel plates with the influence of pollutant concentration and thermophoretic particle deposition.To explore the mass and heat transport features,thermophoretic particle deposition and thermal radiation are considered.The governing equations are transformed into ordinary differential equations with the help of suitable similarity transformations.The Runge-Kutta-Fehlberg’s fourthfifth order technique and shooting procedure are used to solve the reduced set of equations and boundary conditions.The integration of a neural network model based on the Levenberg-Marquardt algorithm serves to improve the accuracy of predictions and optimize the analysis of parameters.Graphical outcomes are displayed to analyze the characteristics of the relevant dimensionless parameters in the current problem.Results reveal that concentration upsurges as the micropolar parameter increases.The concentration reduces with an upsurge in the thermophoretic parameter.An upsurge in the external pollutant source variation and the local pollutant external source parameters enhances mass transport.The surface drag force declines for improved values of porosity and micropolar parameters.

A stencil-like volume of fluid (VOF)method for tracking free interface

A stencil-like volume of fluid （VOF） method is proposed for tracking free interface. A stencil on a grid cell is worked out according to the normal direction of the interface, in which only three interface positions are possible in 2D cases, and the interface can be reconstructed by only requiring the known local volume fraction information. On the other hand, the fluid-occupying-length is defined on each side of the stencil, through which a unified fluid-occupying volume model and a unified algorithm can be obtained to solve the interface advection equation. The method is suitable for the arbitrary geometry of the grid cell, and is extendible to 3D cases. Typical numerical examples show that the current method can give ＂sharp＂ results for tracking free interface.

The Quality Characteristics of Eggs: Impact on the Volume of Allantoin-Amniotic Fluid of Chicken Embryos

In this paper, the eggs＇ weight, quality characteristics （ albumen density, shell quality, yolk size）, and egg weight loss during incubation having impact on volume of allantoin-anmiotic fluid are considered. The major parameters that should be taken into account when creating specialized population of chickens for the production of DEC （ developing embryos of chickens） are determined.

Modeling bubble column reactor with the volume of fluid approach:Comparison of surface tension models

This work aims at comparing surface tension models in VOF(Volume of Fluid) modeling and investigating the effects of gas distributor and gas velocity. Hydrodynamics of a continuous chain of bubbles inside a bubble column reactor was simulated. The grid independence study was first conducted and a grid size of 1.0 mm was adopted in order to minimize the computing time without compromising the accuracy of the results. The predictions were validated by comparing the experimental studies reported in the literature. It was found that all surface tension models can describe the bubble rise and bubble plume in a column with slight deviations.

Asymptomatic fluid volume imbalance and peridialysis blood pressure independently predict cardiovascular and all-cause mortality in patients undergoing hemodialysis

Chronic fluid overload(FO)is a well-known factor which contributes to the high morbidity and mortality of patients undergoing hemodialysis(HD).[1]Higher blood pressure(BP)is commonly associated with overload volume.[1–4]Thus,the measurement time point(eg,pre-dialysis and post-dialysis)and volume status may affect the prognostic value of BP in HD patients.This study aimed to examine the correlation between fluid volume and BP,as well as their prognostic effects in HD patients who were free of coronary artery disease(CAD).

Volumetric fluid analysis of fixed monthly anti-VEGF treatment in patients with neovascular age-related macular degeneration

·AIM:To evaluate visual outcomes and changes in fluid after administering monthly anti-vascular endothelial growth factor(VEGF)injections to treat neovascular agerelated macular degeneration(n AMD)with subretinal fluid(SRF)and pigment epithelial detachment(PED).·METHODS:This prospective study included eyes with n AMD previously treated with as-needed anti-VEGF injections.The patients were treated with six monthly intravitreal injections of ranibizumab.Quantitative volumetric segmentation analyses of the SRF and PED were performed.The main outcome measures included best-corrected visual acuity(BCVA),and SRF and PED volumes.·RESULTS:Twenty eyes of 20 patients were included in this study.At the 6-month follow-up,BCVA and PED volume did not change significantly(P=0.110 and 0.999,respectively)but the mean SRF volume decreased from 0.53±0.82 mm3 at baseline to 0.08±0.23 mm3(P=0.002).The absorption rate of the SRF volume was negatively correlated with the duration of previous antiVEGF treatment(P=0.029).Seven of the 20 eyes(35%)showed a fluid-free macula and significant improvement in BCVA(P=0.036)by month 6.·CONCLUSION:Quantifying the SRF can precisely determine the patient’s responsiveness to anti-VEGF treatment of n AMD.

Hemodynamic effects of different fluid volumes for a fluid challenge in septic shock patients

Background:It is still unclear what the minimal infusion volume is to effectively predict fluid responsiveness.This study was designed to explore the minimal infusion volume to effectively predict fluid responsiveness in septic shock patients.Hemodynamic effects of fluid administration on arterial load were observed and added values of effective arterial elastance(Ea)in fluid resuscitation were assessed.Methods:Intensive care unit septic shock patients with indwelling pulmonary artery catheter(PAC)received five sequential intravenous boluses of 100 mL 4%gelatin.Cardiac output(CO)was measured with PAC before and after each bolus.Fluid responsiveness was defined as an increase in CO>10%after 500 mL fluid infusion.Results:Forty-seven patients were included and 35(74.5%)patients were fluid responders.CO increasing>5.2%after a 200 mL fluid challenge(FC)provided an improved detection of fluid responsiveness,with a specificity of 80.0%and a sensitivity of 91.7%.The area under the ROC curve(AUC)was 0.93(95%CI:0.84-1.00,P<0.001).Fluid administration induced a decrease in Ea from 2.23(1.46-2.78)mmHg/mL to 1.83(1.34-2.44)mmHg/mL(P=0.002),especially for fluid responders in whom arterial pressure did not increase.Notably,the baseline Ea was able to detect the fluid responsiveness with an AUC of 0.74(95%CI:0.59-0.86,P<0.001),whereas Ea failed to predict the pressure response to FC with an AUC of 0.50(95%CI:0.33-0.67,P=0.086).Conclusion:In septic shock patients,a minimal volume of 200 mL 4%gelatin could reliably detect fluid responders.Fluid administration reduced Ea even when CO increased.The loss of arterial load might be the reason for patients who increased their CO without pressure responsiveness.Moreover,a high level of Ea before FC was able to predict fluid responsiveness rather than to detect the pressure responsiveness.

A three-dimensional robust volume-of-fluid solver based on the adaptive mesh refinement

The present study provides a three-dimensional volume-of-fluid method based on the adaptive mesh refinement technique.The projection method on the adaptive mesh is introduced for solving the incompressible Navier-Stokes equations.The octree structure mesh is employed to solve the flow velocities and the pressure.The developed solver is applied to simulate the deformation of the cubic droplet driven by the surface tension without the effect of the gravity.The numerical results well predict the shape evolution of the droplet.

Thermodynamic Equilibrium of the Saturated Fluid with a Free Surface Area and the Internal Energy as a Function of the Phase-Specific Volumes and Vapor Pressure

This study is concerned with describing the thermodynamic equilibrium of the saturated fluid with and without a free surface area A. Discussion of the role of A as system variable of the interface phase and an estimate of the ratio of the respective free energies of systems with and without A show that the system variables given by Gibbs suffice to describe the volumetric properties of the fluid. The well-known Gibbsian expressions for the internal energies of the two-phase fluid, namely for the vapor and for the condensate (liquid or solid), only differ with respect to the phase-specific volumes and . The saturation temperature T, vapor presssure p, and chemical potential are intensive parameters, each of which has the same value everywhere within the fluid, and hence are phase-independent quantities. If one succeeds in representing as a function of and , then the internal energies can also be described by expressions that only differ from one another with respect to their dependence on and . Here it is shown that can be uniquely expressed by the volume function . Therefore, the internal energies can be represented explicitly as functions of the vapor pressure and volumes of the saturated vapor and condensate and are absolutely determined. The hitherto existing problem of applied thermodynamics, calculating the internal energy from the measurable quantities T, p, , and , is thus solved. The same method applies to the calculation of the entropy, chemical potential, and heat capacity.

Synthetic polymers:A review of applications in drilling fluids

With the growth of deep drilling and the complexity of the well profile,the requirements for a more complete and efficient exploitation of productive formations increase,which increases the risk of various complications.Currently,reagents based on modified natural polymers(which are naturally occurring compounds)and synthetic polymers(SPs)which are polymeric compounds created industrially,are widely used to prevent emerging complications in the drilling process.However,compared to modified natural polymers,SPs form a family of high-molecular-weight compounds that are fully synthesized by undergoing chemical polymerization reactions.SPs provide substantial flexibility in their design.Moreover,their size and chemical composition can be adjusted to provide properties for nearly all the functional objectives of drilling fluids.They can be classified based on chemical ingredients,type of reaction,and their responses to heating.However,some of SPs,due to their structural characteristics,have a high cost,a poor temperature and salt resistance in drilling fluids,and degradation begins when the temperature reaches 130℃.These drawbacks prevent SP use in some medium and deep wells.Thus,this review addresses the historical development,the characteristics,manufacturing methods,classification,and the applications of SPs in drilling fluids.The contributions of SPs as additives to drilling fluids to enhance rheology,filtrate generation,carrying of cuttings,fluid lubricity,and clay/shale stability are explained in detail.The mechanisms,impacts,and advances achieved when SPs are added to drilling fluids are also described.The typical challenges encountered by SPs when deployed in drilling fluids and their advantages and drawbacks are also discussed.Economic issues also impact the applications of SPs in drilling fluids.Consequently,the cost of the most relevant SPs,and the monomers used in their synthesis,are assessed.Environmental impacts of SPs when deployed in drilling fluids,and their manufacturing processes are identified,together with advances in SP-treatment methods aimed at reducing those impacts.Recommendations for required future research addressing SP property and performance gaps are provided.

Effect of fracture fluid flowback on shale microfractures using CT scanning

The field data of shale fracturing demonstrate that the flowback performance of fracturing fluid is different from that of conventional reservoirs,where the flowback rate of shale fracturing fluid is lower than that of conventional reservoirs.At the early stage of flowback,there is no single-phase flow of the liquid phase in shale,but rather a gas-water two-phase flow,such that the single-phase flow model for tight oil and gas reservoirs is not applicable.In this study,pores and microfractures are extracted based on the experimental results of computed tomography(CT)scanning,and a spatial model of microfractures is established.Then,the influence of rough microfracture surfaces on the flow is corrected using the modified cubic law,which was modified by introducing the average deviation of the microfracture height as a roughness factor to consider the influence of microfracture surface roughness.The flow in the fracture network is simulated using the modified cubic law and the lattice Boltzmann method(LBM).The results obtained demonstrate that most of the fracturing fluid is retained in the shale microfractures,which explains the low fracturing fluid flowback rate in shale hydraulic fracturing.

Bronchoalveolar lavage fluid assessment facilitates precision medicine for lung cancer

Lung cancer is the most common and fatal malignant disease worldwide and has the highest mortality rate among tumor-related causes of death.Early diagnosis and precision medicine can significantly improve the survival rate and prognosis of lung cancer patients.At present,the clinical diagnosis of lung cancer is challenging due to a lack of effective non-invasive detection methods and biomarkers,and treatment is primarily hindered by drug resistance and high tumor heterogeneity.Liquid biopsy is a method for detecting circulating biomarkers in the blood and other body fluids containing genetic information from primary tumor tissues.Bronchoalveolar lavage fluid(BALF)is a potential liquid biopsy medium that is rich in a variety of bioactive substances and cell components.BALF contains information on the key characteristics of tumors,including the tumor subtype,gene mutation type,and tumor environment,thus BALF may be used as a diagnostic supplement to lung biopsy.In this review,the current research on BALF in the diagnosis,treatment,and prognosis of lung cancer is summarized.The advantages and disadvantages of different components of BALF,including cells,cell-free DNA,extracellular vesicles,and micro RNA are introduced.In particular,the great potential of extracellular vesicles in precision diagnosis and detection of drug-resistant for lung cancer is highlighted.In addition,the performance of liquid biopsies with different body fluid sources in lung cancer detection are compared to facilitate more selective studies involving BALF,thereby promoting the application of BALF for precision medicine in lung cancer patients in the future.

Scattering and absorption imaging of a highly fractured fluid-filled seismogenetic volume in a region of slow deformation

Regions of slow strain often produce swarm-like sequences,characterized by the lack of a clear mainshockaftershock pattern.The comprehension of their underlying physical mechanisms is challenging and still debated.We used seismic recordings from the last Pollino swarm(2010-2014) and nearby to separate and map seismic scattering(from P peak-delays) and absorption(from late-time coda-wave attenuation) at different frequencies in the Pollino range and surroundings.High-scattering and high-absorption anomalies are markers of a fluid-filled fracture volume extending from SE to NW(1.5-6 Hz) across the range.With increasing frequency,these anomalies approximately cover the area where the strongest earthquakes occurred from the sixteenth century until 1998.In our interpretation,the NW fracture propagation ends where carbonates of the Lucanian Apennines begin,as marked by a high-scattering and low-absorption area.At the highest frequency(12 Hz) the anomalies widen southward in the middle of the range,consistently marking the faults active during the recent Pollino swarm.Our results suggest that fracture healing has closed small-scale fractures across the SE faults that were active in the past centuries,and that the propagation of fluids may have played a crucial role in triggering the 2010-2014 Pollino swarm.Assuming that the fluid propagation ended at the carbonates barrier in the NW direction,fractures opened new paths to the South,favoring the nucleation of the last Pollino swarm.Indeed,the recently active faults in the middle of the seismogenic volume are marked by a high-scattering and highabsorption footprints.Our work provides evidence that attenuation parameters may track shape and dynamics of fluid-filled fracture networks in fault areas.

Effect of bubble morphology and behavior on power consumption in non-Newtonian fluids’aeration process

Due to a prolonged operation time and low mass transfer efficiency, the primary challenge in the aeration process of non-Newtonian fluids is the high energy consumption, which is closely related to the form and rate of impeller, ventilation, rheological properties and bubble morphology in the reactor. In this perspective, through optimal computational fluid dynamics models and experiments, the relationship between power consumption, volumetric mass transfer rate(kLa) and initial bubble size(d0) was constructed to establish an efficient operation mode for the aeration process of non-Newtonian fluids. It was found that reducing the d0could significantly increase the oxygen mass transfer rate, resulting in an obvious decrease in the ventilation volume and impeller speed. When d0was regulated within 2-5 mm,an optimal kLa could be achieved, and 21% of power consumption could be saved, compared to the case of bubbles with a diameter of 10 mm.

Reservoir quality evaluation of the Narimba Formation in Bass Basin,Australia:Implications from petrophysical analysis,sedimentological features,capillary pressure and wetting fluid saturation

The evaluation of reservoir quality was accomplished on the Late Paleocene to Early Eocene Narimba Formation in Bass Basin,Australia.This study involved combination methods such as petrophysical analysis,petrography and sedimentological studies,reservoir quality and fluid flow units from derivative parameters,and capillary pressure and wetting fluid saturation relationship.Textural and diagenetic features are affecting the reservoir quality.Cementation,compaction,and presence of clay minerals such as kaolinite are found to reduce the quality while dissolution and secondary porosity are noticed to improve it.It is believed that the Narimba Formation is a potential reservoir with a wide range of porosity and permeability.Porosity ranges from 3.1%to 25.4%with a mean of 15.84%,while permeability ranges between 0.01 mD and 510 mD,with a mean of 31.05 mD.Based on the heterogenous lithology,the formation has been categorized into five groups based on permeability variations.Group I showed an excellent to good quality reservoir with coarse grains.The impacts of both textural and diagenetic features improve the reservoir and producing higher reservoir quality index(RQI)and flow zone indicators(FZI)as well as mostly mega pores.The non-wetting fluid migration has the higher possibility to flow in the formation while displacement pressure recorded as zero.Group II showed a fair quality reservoir with lower petrophysical properties in macro pores.The irreducible water saturation is increasing while the textural and digenetic properties are still enhancing the reservoir quality.Group III reflects lower quality reservoir with mostly macro pores and higher displacement pressure.It may indicate smaller grain size and increasing amount of cement and clay minerals.Group IV,and V are interpreted as a poor-quality reservoir that has lower RQI and FZI.The textural and digenetic features are negatively affecting the reservoir and are leading to smaller pore size and pore throat radii(r35)values to be within the range of macro,meso-,micro-,and nano pores.The capillary displacement pressure curves of the three groups show increases reaching the maximum value of 400 psia in group V.Agreement with the classification of permeability,r35 values,and pore type can be used in identifying the quality of reservoir.

An inverse analysis of fluid flow through granular media using differentiable lattice Boltzmann method

This study presents a method for the inverse analysis of fluid flow problems.The focus is put on accurately determining boundary conditions and characterizing the physical properties of granular media,such as permeability,and fluid components,like viscosity.The primary aim is to deduce either constant pressure head or pressure profiles,given the known velocity field at a steady-state flow through a conduit containing obstacles,including walls,spheres,and grains.The lattice Boltzmann method(LBM)combined with automatic differentiation(AD)(AD-LBM)is employed,with the help of the GPU-capable Taichi programming language.A lightweight tape is used to generate gradients for the entire LBM simulation,enabling end-to-end backpropagation.Our AD-LBM approach accurately estimates the boundary conditions for complex flow paths in porous media,leading to observed steady-state velocity fields and deriving macro-scale permeability and fluid viscosity.The method demonstrates significant advantages in terms of prediction accuracy and computational efficiency,making it a powerful tool for solving inverse fluid flow problems in various applications.

Endoscopic intramural cystogastrostomy for treatment of peripancreatic fluid collection: A viewpoint from a surgeon

Percutaneous or endoscopic drainage is the initial choice for the treatment of peripancreatic fluid collection in symptomatic patients.Endoscopic transgastric fenestration(ETGF)was first reported for the management of pancreatic pseu-docysts of 20 patients in 2008.From a surgeon’s viewpoint,ETGF is a similar procedure to cystogastrostomy in that they both produce a wide outlet orifice for the drainage of fluid and necrotic debris.ETGF can be performed at least 4 wk after the initial onset of acute pancreatitis and it has a high priority over the surgical approach.However,the surgical approach usually has a better success rate because surgical cystogastrostomy has a wider outlet(>6 cm vs 2 cm)than ETGF.However,percutaneous or endoscopic drainage,ETGF,and surgical approach offer various treatment options for peripancreatic fluid collection patients based on their conditions.

On the experimental characterization of the fluid volume influence on the friction between rough surfaces

The load-bearing behaviour of lubricated contacts depends primarily on the normal force,the relative velocity,and the geometry.Thus,with the aid of the Stribeck curve,it is usually well possible to characterize whether hydrodynamics,mixed friction,or boundary friction is more likely to be present.The fact that the load regime can also depend on the fluid quantity is obvious,but has hardly been systematically investigated so far.Especially for contacts with microscopic roughness,the defined application of a very small amount of fluid is a very challenging requirement.In this paper,a very fundamental study shows how a pin-on-disc tribometer can be used to achieve the transition from dry friction via mixed friction to predominant hydrodynamics by the amount of supplied fluid.The experiments are carried out on samples filed with different coarseness.In addition,the simultaneous influence of partial filling and normal force as well as relative velocity is also shown.Very good reproducibility has been practically reached over the entire range of the tests.Regarding the quantities for the coefficient of friction(COF),it was concluded that close to full filling,a reduction of the fluid quantity has a similar effect on the COF as the reduction of the velocity.This property goes along with the common theory of starved lubricated systems.Such behaviour was not observed to the same extent for the normal force.In the vicinity of smaller fluid quantities,the COF increases very rapidly with further reduction in fluid quantity,far more disproportionately than that with reduction in velocity.With a deeper understanding of this problem,various practical issues such as idling or the run-up process in bearings can also be studied in a more focused manner.

Step-over of strike-slip faults and overpressure fluid favor occurrence of foreshocks:Insights from the 1975 Haicheng fore-main-aftershock sequence,China

This study analyzed and summarized in detail the spatial and temporal distributions of earthquakes,tidal responses,focal mechanisms,and stress field characteristics for the M 7.3 Haicheng earthquake sequence in February 1975.The foreshocks are related to the main fault and the conjugate faults surrounding the extension step-over in the middle.The initiation timing of the foreshock clusters and the original time of the mainshock were clearly modulated by the Earth's tidal force and coincided with the peak of dilational volumetric tidal strain.As a plausible and testable hypothesis,we proposed a fluid-driven foreshock model,by which all observed seismicity features can be more reasonably interpreted with respect to the results of existing models.Together with some other known examples,the widely existing step-over along strike-slip faults and associated conjugate faults,especially for extensional ones in the presence of deep fluids,favor the occurrence of short-term foreshocks.Although clustered seismicity with characteristics similar to those of the studied case is not a sufficient and necessary condition for large earthquakes to occur under similar tectonic conditions,it undoubtedly has a warning significance for the criticality of the main fault.Subsequent testing would require quantification of true/false positives/negatives.