Studies of Adsorption of Cadmium Ions by Biowaste Adsorbent from Aqueous Solutions with Ion-Selective Electrodes and ICP-OES

Using environment-friendly and low-cost biowaste adsorbents as toxic metal ion removal substrates from aqueous solutions has a great economic advantage. This work evaluated pumpkin and potato peel biowastes for the adsorption of cadmium ions. The biowastes were treated with acid or base. Batch experiments were carried out by introducing a known concentration of metal ion solution into the biowaste sorbent at various pH levels. The pH and metal ion concentration was monitored with pH and cadmium ion-selective electrode continuously for two hours, and the final concentration for the metal ion after 24 hours was measured with the cadmium electrode and then confirmed with ICP-OES. L-type isotherms were obtained that fit to Freundlich model. Adsorption isotherms showed chemical adsorption and the kinetics following the second order model. Equilibrium adsorption capacity is higher than 29 mg/g at pH 5.6 when the initial concentration is 220 ppm. Dynamic cadmium adsorption capacity is 17 mg/g from aqueous solution when the feed solution is 220 ppm with pumpkin peel biowaste sorbent. The biowaste materials can be regenerated with acid washing.

Dye-sensitized Solar Cells with Higher J_(sc) by Using Polyvinylidene Fluoride Membrane Counter Electrodes

A flexible counter electrode(CE) for dye-sensitized solar cells(DSCs) has been fabricated using a micro-porous polyvinylidene fluoride membrane as support media and sputtered Pt as the catalytic material.Non-conventional structure DSCs have been developed by the fabricated CEs. The Pt metal was sputtered onto one surface of the membrane as the catalytic material. DSCs were assembled by attaching the Ti O2 electrode to the membrane surface without Pt coating. The membrane was with cylindrical pore geometry. It served not only as a substrate for the CE but also as a spacer for the DSC. The fabricated DSC with the flexible membrane CE showed higher photocurrent density than the conventional sandwich devices based on chemically deposited Pt/FTO glass, achieving a photovoltaic conversion efficiency of 4.43%. The results provides useful information in investigation and development of stable, low-cost, simple-design, flexible and lightweight DSCs.

Protective electrode/electrolyte interphases for high energy lithium-ion batteries with p-toluenesulfonyl fluoride electrolyte additive

High energy density lithium-ion batteries using Ni-rich cathode(such as LiNi0.6Co0.2Mn0.2O2) suffer from severe capacity decay.P-toluenesulfonyl fluoride(pTSF) has been investigated as a novel film-forming electrolyte additive to enhance the cycling performances of graphite/LiNi0.6Co0.2Mn0.2O2 pouch cell.In comparison with the baseline electrolyte,a small dose of pTSF can significantly improve the cyclic stability of the cell.Theoretical calculations together with experimental results indicate that pTSF would be oxidized and reduced to construct protective interphase film on the surfaces of LiNi0.6Co0.2Mn0.2O2 cathode and graphite anode,respectively.These S-containing surface films derived from pTSF effectively mitigate the decomposition of electrolyte,reduce the interphasial impedance,as well as prevent the dissolution of transition metal ions from Ni-rich cathode upon cycling at high voltage.This finding is beneficial for the practical application of high energy density graphite/LiNi0.6Co0.2Mn0.2O2 cells.

Direct Determination of Potassium-Sodium Activity Ratio in Soil Suspension with Two Ion-Selective Electrodes

A K+-selective electrode and a Na+-selective electrode were used to construct a measuring cell without liquid-junction for the determination of the ion activity ratio of K+ to Na+ in soil suspensions. The measured cell potential was not affected by the total electrolyte concentration when the total cation concentration was 10-1-10-3 mol L-1 and the concentration ratio CK+ / CNa+. was 10:1 to 1:50. When the concentration ratios were equal to 1and the total electrolyte concentrations were 10-2 and 10-3 mol L-1, the ion activity ratio measurement would not be affected by pH in the pH range of 3.5 to 11.5 and 4.4 to 11 respectively. Ions other than H+ have no remarkable influence on the measurement. The ion activity ratio of K+ to Na+ measured directly in soil suspension agree well with those in centrifuged supernant solution. The relative deviation was within 4%. From the measured ion activity ratio, the difference of the bonding energies of K+ and Na+ ions was calculated.

Preparation of CeO_2 Nanoparticles and Its Application to Ion-selective Electrodes Based on Acetyl Cellulose

CeO2 nanoparticles with an average diameter of about 30 nm were prepared by sol-gel method at lower temperature. The gel, transformed from the aqueous solution of metal nitrate and citric acid, can be combusted completely at lower temperature. The redox behavior and the crystallization process of the dried gel were studied by thermogravimetric analysis and infrared spectroscopy. The synthesized powders were characterized by X-ray powder diffraction and transmission electron microscopy. In addition, rare earth elements ion-selective electrodes based on acetyl cellulose were prepared using ultra fine cerium oxide powders.

Determination of Boron Trifluoride in Boron Trifluoride Complex by Fluoride Ion Selective Electrode

A method was proposed to determine boron trifluoride in boron trifluoride complex using fluoride ion selective electrode(ISE). Hydroxide was chosen to mask aluminum for the determination of 0.01—0.1 mol/L of fluoride. The simulation indicated that the permissible aluminum masked at a certain p H value was limited and hardly related to F-concentration and boric acid. It is better to control p H value below 11.5 and the aluminum concentration within 0.025 mol/L to minimize the interference of hydroxide to the fluoride ISE. The decomposition conditions of boron trifluoride by aluminum chloride were investigated. It is found that the F-detection ratio will approach 1.0 if the Al/F molar ratio is 0.3—0.7 and aluminum concentration is no more than 0.02 mol/L when heated at 80 ℃ for 10 min. In one word, hydroxide is quite fit to mask aluminum for samples which contain high content of fluoride and aluminum and the BF3 content can be successfully determined by this method.

High-temperature Reference Electrodes Used in Molten Fluorides

The thermodynamic and dynamic behaviour of Ni^(2+)|Ni couple in FLINAK melt is investigated by us- ing EMF measurement and micropolarization method.The couple shows the Nernstian reversibility and a large exchange current density(6 mA·cm^(-2)).A single crystal LaF_3 which is a fluoride ion conductor used as a membrane of the Ni^(2+)|Ni couple reference electrode is reliable in FLINAK melts at 973 K.The poten- tial of LaF_3 membrane reference electrode is constant within±2 mV.The boron nitride used as a salt bridge was not good in FLINAK melts.The platinum electrode is studied by using micropolarization.The equilibrium potential of Pt electrode is dependent on the absorption and the electrochemical reaction.The potential is stable for a constant composition at constant temperature.

Construction and Application of a PVC Membrane Enoxacin Ion-selective Electrode Based on a Needle-shaped Inner Reference Electrode

A PVC membrane enoxacin ion-selective electrode based on a needle-shaped inner reference electrode was prepared. A Ag/AgCl wire was used as the substrate of this electrode. It was previously coated with a thin sheet of urea-formaldehyde resin containing Cl - ions to form a needle-shaped inner reference electrode, then the inner reference electrode was coated with a thin sheet of a PVC membrane containing an enoxacin tetraphenylborate ion-pair complex. The influences of various ion-pair complexes, concentrations of the active components in the membrane and the plasticizers on the performance of the electrode were studied by orthogonal design. The linear response range of the electrode was 7.9×10 -5 -1.0×10 -2 mol/L. The detection limit was 2.0×10 -5 mol/L. The slope was 30.4 mV/decade(25 ℃). The electrode can be used for the potentiometric determination of enoxacin tablets directly. The average recovery was 100.4%, and the RSD was 0.9%. The results agreed with those determined by the method in Chinese Pharmacopoeia.

Potentiometric Urea Biosensor Based on Ion-Selective Electrode by Different Immobilization Procedures

Enzyme was immobilized on an ammonium ion-selective electrode by different methods.An ion-selective electrode is not completely ion-specific,and interfering ions react with the ion-selective electrode membrane,altering the measured potential.Therefore,the characteristics of the effect of other ions on ammonium ion-selective electrode-based urea biosensors are considered.Based on the experimental results,the urea biosensor based on entrapment had a high response voltage of around 189 mV and fast response time of around 16 sec.Moreover,selectivity of the urea biosensor in different interfering ions was considered to elucidate the characteristics of ammonium ion-selective electrode-based biosensors.

STUDY OF CALCIUM ION-SELECTIVE ELECTRODE BASED ON A NEW NEUTRAL CARRIER

A calcium ion-setective eletrode based on a new neutral carrier was studied.The electrode gives a Nernstian response in the rang 5.9-1 Pa and the response is stable in a wide pH range.Logarithms of setectivity coefficents are -2.3 Li(+),-3.5 Na(+),-4.0 K(+),-3.7NH_4(+),-4.5 Mg(2+) and -4.4Zn(2+).

Determination of Fluoride in Various Samples Using a Fluoride Selective Electrode

Fluoride is widespread in the environment, water, air, vegetation and Earth’s crust which can entre ground and surface water by natural process. Fluoride in minute quantities is essential component for human health and help in normal mineralization of bone and formation of dental enamel. The determination of fluoride in some species was performed by using fluoride ion-selective electrode by direct measurement and standard addition method. The concentration of fluoride ion was determined in drinking water (from different place at Kathmandu), toothpaste, various brand of tea and coffees. The range of fluoride concentration in water sample was 0.16 to 0.39 mg/l, tea and coffee samples were 0.011 to 0.084 mg/l and its value of toothpaste was 0.026 to 0.75 mg/l. The concentration of fluoride ion obtain from different sample was compared with the legitimate value given by the world health organization.

A comparative study of four 20-membered N_2S_4-crown ethers as ionophores for polymeric membrane silver selective electrodes

Four 20-membered N_2S_4-monoazathiacrown ethers have been synthesized and explored as neutral ionophores for Ag^+-selective electrodes.Potentiometric responses reveal that the flexibility of the ligands has great effect on the selectivity and sensitivity to Ag^+ ions.The electrode based on ionophore 9,10,20,25-tetrahydro-5H,12H-tribenzo[b,n,r][1,7,10,16,4,13]tetrathiadiaza cycloicosine 6,13-(7H,14H)-dione(C) with 2-nitrophenyl octyl ether(o-NPOE) as solvent in a poly(vinyl chloride)(PVC) membrane matrix sho...

Effect of Packaging Material on Piezoelectric Response of Sensor with Electrospinning Polyvinylidene Fluoride (PVDF) Nanofiber Web

The polyvinylidene fluoride(PVDF)nanofiber web by electrospinning technology has the characteristics of fast response,high sensitivity,wide range of pressure,etc.,and provides new sensitive materials for the sensor testing the dynamic pressure such as foot pressure during walking.Because of the nanofiber mesh structure,it must be packaged to collect piezoelectric charge and bear strong mechanical behavior before industrial practice.The PVDF nanofiber web is usually packaged by incorporating a pair of flexible electrode as well as the lead of signal output.This present work will introduce the detailed packaging process and technology of PVDF nanofiber web,and three different types of packaging electrode materials(adhesive copper foil tape,indium tin oxide(ITO)thin plate,and adhesive conductive cloth)in previously published literatures are compared by the piezoelectric response of their sensor prototypes to a periodic mechanical activation.The results showed that the surface property of packaging material had a significant effect on the piezoelectric response of sensor by PVDF nanofiber web.For PVDF nanofiber web sensor,therefore,it needed a deep investigation on the specific packaging technology in terms of different working conditions.

Ion Selective Electrode Array Analysis Using Variable Step-Size Generalized Simulated Annealing

A global optimum location algorithm called Variable Step-Size Generalized Simulated Annealing(VSGSA) was applied to treating the data obtained by using an array of ion-electrodes in solutions containing mixtures of Na+, K+, Ca2+. Unlike traditional optimization algorithms such as simplex procedure, VSGSA can be used to determine the model parameters without any priori information about the analytical system under investigation and overcome the disadvantage of simplex method which might converge to local extrema depending on the starting positions. The algorithm was applied to po-tentiometric determination of ions in mixture solutions.

Binding mechanism of halide ions to bovine serum albumin and hemoglobin: investigated by ion selective-electrode

The binding mechanism of the interactions of halide ions (F–, Br– and I–) with bovine serum albumin (BSA) and hemoglobin (Hb) were studied at different temperatures, by using ion-selective electrodes. The experimental data were treated according to Klotz equation, and the number of binding sites and the binding constants were determined. The results show that the binding sites of F– on protein molecules are more than those of Br– and I–. Additionally, the number of the binding sites for halide ions on protein molecules increases with increasing temperature. This study also indicates that the binding constants for the interactions of halide ions with proteins gradually decrease as the size of halide ions and temperature increases. These behaviors were reasonably interpreted with the structural and thermodynamic factors. The thermodynamic functions at different temperatures were calculated with thermodynamic equations, and the enthalpy change for the interactions were also determined by isothermal titration calorimetry (ITC) at 298.15 K, which indicate that the interactions of halide ions with proteins are mainly electrostatic interaction.

Coulometric Response of H-Selective Solid-Contact Ion-Selective Electrodes and Its Application in Flexible Sensors+

The analytical performance of H+-selective solid-contact ion-selective electrodes(SCISEs)based on solid contact polyaniline doped with chloride(PANI(Cl))and poly(3,4-ethylenedioxythiophene)doped with poly(styrene sulfonate)(PEDOT(PSS))was characterized by a developed coulometric signal transduction method.PEDOT(PSS)solid contact is covered by PVC based H+-selective membrane.The obtained coulometric signal demonstrates that the cumulated charge can be amplified by increasing the capacitance of solid contact.SCISEs covered with spin-coated membrane behave faster amperometric response than electrodes with drop-cast mem-brane.In contrast to earlier works,the amperometric response and impedance spectrum demonstrates H+transfer through SCISEs is independent from the thickness of membrane.The exceptional behavior of PANI(Cl)H+-SCISEs shows that the capacitance estimated from impedance spectrum at low frequency 10 mHz and coulometric signal of PANI(Cl)based SCISEs is influenced by the applied po-tentials,whereas PEDOT(PSS)solid contact is independent from the chosen applied potentials.Furthermore,preliminary investiga-tions of coulometric signal transduction on flexible pH sensor implies its potential applications in wearable sensors for sweat ion concentration detection.

土壤环境氟化物测定中的离子选择电极分析方法

本文使用离子选择电极法测定土壤样品中的氟化物。为提高测定结果的精确性,测定实验中需要使用总离子强度调节缓冲液。选取TISAB1和TISAB2两种常用缓冲液进行对比实验,结果表明TISAB1缓冲液的3次测定结果均在保证值规定范围内,可以更好地满足氟化物测定实验中提高测定精度的需要。金属离子干扰实验表明,在Al^(3+)浓度不超过10 mg/L、Fe^(3+)浓度不超过50 Mg/L、Ca^(2+)浓度不超过100 mg/L的情况下,3种金属离子不会对氟化物测定结果产生干扰。土壤水溶态氟化物的检出限为2.1μg,土壤全态氟化物的检出限为2.2μg,可以满足土壤环境氟化物测定要求。

离子色谱法和离子选择电极法对氟化氢溶液中的氟化物分析对比

氟化物指含负价氟的有机或无机化合物。与其他卤素类似,氟生成单负阴离子。无机氟化物的例子有氢氟酸(HF)、氟化钠(NaF)等。本文用离子选择电极法和离子色谱法分别分析含氢氟酸(HF)溶液中的氟化物。发现溶液含有氢氟酸(HF)时分析氟化物,分析结果与p H值形成干扰,pH值越低氟化物的结果越高,而采用氢氧化钠将溶液中和成碱性条件和用碳酸钠-碳酸氢钠淋洗液体系稀释样品时,干扰最小。而含氢氟酸(HF)溶液采用离子选择电极法分析时溶液pH值偏低,H+偏高,会氟化物的浓度偏高,而溶液p H值调至中性条件时干扰最小,结果最接近真值。

离子选择电极法测定水中氟化物的不确定度评定

目的:采用离子选择电极法测定生活饮用水中氟化物的含量,评定测定过程中的不确定度分量。方法:依据标准《测量不确定度评定与表示》(JJF 1059.1—2012)和《化学分析中不确定度的评估指南》(CNAS-GL006:2019),分析不确定度来源,建立数学模型,对测定过程中的各不确定度分量进行分析和计算,综合评估氟化物含量的不确定度。结果:当生活饮用水中氟化物的含量为0.915 mg·L^(-1)时,其扩展不确定度为0.038 mg·L^(-1)(k=2),测定结果可表示为(0.915±0.038)mg·L^(-1)(k=2)。结论:影响检测结果不确定度的因素主要是标准系列溶液的配制,在实验中可以通过严格控制标准系列溶液的配制过程提高检测结果的准确性。

氟离子选择电极法测定土壤中水溶性氟化物和总氟化物含量

采用氟离子选择电极法测定土壤中水溶性氟化物和总氟化物。结果表明,氟化物含量在5~500μg范围内具有良好的线性关系(>0.999),水溶性氟化物方法检出限为0.5 mg/kg,相对标准偏差(RSD,n=6)为3.8%~6.7%,总氟化物方法检出限为43 mg/kg,相对标准偏差(RSD,n=6)为4.0%~4.2%,满足标准方法的测定要求。有证标准物质RMU044和RMU045测定结果均在标准范围内,水溶性氟化物相对误差为-3.3%~-2.4%,相对标准偏差为4.0%~4.7%,总氟化物相对误差为0.9%~1.3%,相对标准偏差为1.0%~2.2%。实际样品加标回收率试验时,水溶性氟化物平均加标回收率为100%,总氟化物的平均加标回收率为94%,该实验方法重现性好,准确度高,操作简单。