Study on gas metal arc welding of two types of TMCP steels

Gas metal arc welding experiments were conducted on two types of steels with 0.41% carbon equivalent(Ceq) and 0.31% Cequsing WER70T wire and 20% CO_(2)and 80% Ar as shielding gas.The two types of steels show satisfactory weldability.The transition temperatures of 50% upper shelf energy(Tk0.5) for Charpy-V impact test of both the welded joints are below-40 ℃.However, the toughness of the fusion line zone and heat-affected zone(HAZ) of the two steel joints exhibits differences, with the toughness of 0.41% Ceqsteel being better than that of 0.31% Ceqsteel.The Tk0.5of the fusion line zone and the HAZ of 0.41% Ceqsteel is below-60℃,whereas that of 0.31% Ceqsteel is above-40℃.The welded joint of 0.41% Ceqsteel has low hardness fluctuation, while that of 0.31% Ceqsteel exhibits a narrow, softened zone, which has no obvious influence on the tested tensile strength.The coarse grain heat-affected zone(CGHAZ)microstructure of 0.41% Ceqsteel is bainite, while that of 0.31% Ceqsteel is bainite with ferrite and minor pearlite.

Study on arc characteristics and behavior of metal transfer in pulse current flux-cored arc welding of mild steel

The variation in arc characteristics and behavior of metal transfer with the change in pulse parameters has been studied by high speed video camera during pulse current flux-cored arc weld deposition.A comparative study of similar nature has also been carried out during flux-cored arc weld deposition in globular and spray transfer modes.The effect of pulse parameters has been studied by considering their mean current and arc voltage.The arc characteristics studied by its root diameter,projected diameter and length,and the behavior of metal transfer noted by the metal transfer model and the droplet diameter have been found to vary significantly with the pulse parameters.The observation may help in understanding the arc characteristics with respect to the variation in pulse parameters which may be beneficial in using pulse current FCAW to produce desired weld quality.

A novel single wire indirect arc metal inert gas welding process operated in streaming mode

Dilution of a pad weld must be limited to a certain critical level to improve its wear and/or corrosion properties.To do that,a novel single wire indirect arc metal inert gas welding process operated in streaming mode was realized.A metal inert gas welding torch,arranged perpendicular to a substrate in vertical position,is fixed with an auxiliary tungsten electrode horizontally.The arc is ignited between a wire through the torch and the auxiliary electrode.The substrate is not electrically connected.The welding current is set in the range of streaming mode.304 stainless steel was pad welded on Q235 substrates in vertical position by this process.Microstructures were analyzed with optical microscope.Dilution ratios were measured with stereo light microscope and calculated.The results show that,after eliminating interference of the massive torch setup,the dilution ratio of the pad weld with optimized parameters is 5.07%,much less than that with a metal inert gas welding process,which is 26.46%.The pad weld is bonded to the substrate without defects.Microstructures of the pad weld consist of columnar austenite and ferrite between the columns.The dilution ratio increases with increasing welding current or welding velocity,and decreases with increasing distance to the substrate.

Feature Extraction and Dimensionality Reduction of Arc Sound under Typical Penetration Status in Metal Inert Gas Welding

Arc sound is well known as the potential and available resource for monitoring and controlling of the weld penetration status,which is very important to the welding process quality control,so any attentions have been paid to the relationships between the arc sound and welding parameters.Some non-linear mapping models correlating the arc sound to welding parameters have been established with the help of neural networks.However,the research of utilizing arc sound to monitor and diagnose welding process is still in its infancy.A self-made real-time sensing system is applied to make a study of arc sound under typical penetration status,including partial penetration,unstable penetration,full penetration and excessive penetration,in metal inert-gas（MIG） flat tailored welding with spray transfer.Arc sound is pretreated by using wavelet de-noising and short-time windowing technologies,and its characteristics,characterizing weld penetration status,of time-domain,frequency-domain,cepstrum-domain and geometric-domain are extracted.Subsequently,high-dimensional eigenvector is constructed and feature-level parameters are successfully fused utilizing the concept of primary principal component analysis（PCA）.Ultimately,60-demensional eigenvector is replaced by the synthesis of 8-demensional vector,which achieves compression for feature space and provides technical supports for pattern classification of typical penetration status with the help of arc sound in MIG welding in the future.

Study on chaos in short circuit gas metal arc welding process

Based on the chaos theory, an idea is put forward to analyze the short circuit Gas Metal Arc Welding （ GMAW-S） process. The theory of phase space reconstruction and related algorithms such as mutual information and so on, are applied to analyze the chaos of the GMAW-S process. The largest Lyapunov exponents of some current time series are calculated, and the results indicate that chaos exists in the GMAW-S process. The research of the chaos in the GMAW-S process can be help to get new knowledge of the process.

Inclusion behavior and microstructure of weld metal with Ce in twin wire high heat input submerged-arc welding

In this study,the welding thermal cycle curve exhibited two temperature peaks in high heat-input twin-wire separate-pool submerged-arc welding and coarse-grained heat affected zone existed in the welded joint. The inclusions of primary weld metal and coarse-grained heat affected zone of Ce-added SAW should be Al_2O_3,MnO,SiO_2,TiO,Ce_2S_3,CeS,Ce_2O_2S and Ce_2O_3. Under the effect of welding thermal cycle,oxy-sulfides inclusions of Ce,the diameter of which was less than 2. 0 μm,slightly grew larger,but the composition and type of the inclusions didn't change. The microstructure of the large heat input weld metal had acicular ferrite that Ce oxide sulphide particles induced nucleation and proeutectoid ferrite. In the coarse-grained heat affected zone of weld metal,home-position precipitation of acicular ferrite and sympathetic acicular ferrite were both observed. It was supposed that previous crystal cells of acicular ferrite in austenite grain promoted home-position precipitation of acicular ferrite. Meanwhile,sympathetic acicular ferrite tended to nucleate at the primary acicular ferrite grain boundaries,where high dislocation density was located,and grew inside the neighboring carbon-depleted austenitic regions. The granular bainite nucleated in the austenitic zone with high carbon content close to acicular ferrite and sympathetic acicular ferrite.

Computer-based sensing and visualizing of metal transfer mode in gas metal arc welding

Using Xenon lamp lights to overcome the strong interference from the welding arc, a computer-based system is developed to sense and visualize the metal transfer in GMAW. This system combines through-the-arc sensing of the welding current and arc voltage with high speed imaging of the metal transfer. It can simultaneously display the metal transfer processes and waveforms of electrical welding parameters in real-time The metal transfer videos and waveforms of electrical welding parameters can be recorded. Metal transfers under various welding conditions have been investigated with the system developed.

Digital control of pulsed gas metal arc welding inverter using TMS320LF2407A

A digital control of pulsed gas metal arc welding inverter was proposed. A control system consisting of analogue parts was replaced with a new digital control implemented in a TMS320LF2407A DSP chip. The design and constructional features of the whole digital control were presented. The resources of the DSP chip were efficiently utilized and the circuits are very concise, which can enhance the stability and reliability of welding inverter. Experimental results demonstrate that the developed digital control has the ability to accomplish the excellent pulsed gas metal arc welding process and the merits of the developed digital control are stable welding process, little spatter and perfect weld appearance.

Numerical Simulation of Molten Metal Droplet Behavior in Gas Metal Arc Welding by Three-Dimensional Incompressible Smoothed Particle Hydrodynamics Method

The numerical model was developed using a SPH (Smoothed Particle Hydrodynamics) method and the projected transfer phenomena during a GMA (Gas Metal Arc) welding were simulated by the model to clarify mechanisms of the phenomena. As a result, the droplet transfer mode obtained from this calculation was regarded as a projected transfer mode in which the liquid column grew about 1 mm and a droplet grew up until its diameter became large the same as a wire diameter,?after that it was detached from the tip of the column. In addition, 10 droplets were formed for 0.1 s through these growth and detachment processes at the tip of a wire. To compare with the numerical results, actual GMA welding was carried out and molten metal droplet transfers were taken by high speed camera. The diameter of a wire, the length of a liquid column, the velocity of a droplet right before it reached a weld pool obtained by simulation showed good agreement with experiment.

Microstructure and mechanical properties of AZ31B magnesium alloy gas metal arc weld

Wrought magnesium alloy sheets were butt welded with gas metal arc welding process. Pores in the weld were investigated under different welding parameters, the causes of pore formation were systematically disposed, and the effects of porosity on the microstructure and mechanical properties of the joint were analyzed. The microstructure examination shows that the pores mainly appear close to the top or bottom part of the weld, and could connect to each other and lead to the formation of cracks in the welds. However, the pores can be controlled with proper welding parameters. The tensile testing results reveal that the average joint strength is close to or higher than that of the base metal. The microhardness in the weld can be even higher than that in the base metal due to the second ohase strengthening of β-Mg17（A1, Zn）12 formed in the weld.

Determining chaotic invariant properties of short-circuiting gas metal arc welding from an observed time series

The experimental time series of welding current produced by carbon dioxide gas metal arc welding with shortcircuiting transfer were recorded and subsequently evaluated. Based on phase space reconstruction, the correlation dimeusions and Kolmogorov entropies of the corresponding system have been numerically calculated using the Grassberger-Procaccia algorithm at different time delays. It was found out that the time delay has little effect on the estimation of correlation dimension; conversely, it plays a key role in producing precise results on the estimation of Kolmogorov entropy.

Experimental study on gas metal arc welding and laser hybrid welding of WYS700 steel

Gas metal arc welding, laser welding, and laser-metal active gas welding(MAG) hybrid welding methods were applied to WYS700 steel.Different welding procedures were performed and different welding technologies were compared.Macro metallographs of the welded joints were obtained, and the mechanical properties(such as tensile strength, bending property, and hardness) of the joints formed using the different welding technologies were determined.The results revealed that the joint of the WYS700 steel could be formed well through gas metal arc welding, laser welding, and laser-MAG hybrid welding.Furthermore, the softening of the welding heat affected zone can be effectively reduced to obtain good strength and plasticity by using a suitable welding procedure.Laser-MAG hybrid welding allows the realization of high efficiency and deep penetration for the welding of thick plates with specifications above 3 mm.

Gas metal arc welding of duplex stainless clad steel plates

The 2205 duplex stainless ＋ DH36 clad steel plate was welded by gas metal arc welding（GMAW）, and the welding performance of the clad steel plate was investigated. The results show that the adaptability of the welding procedure for the base metal of carbon steel, the transition layer, and the cladding material is excellent. The test results indicate that the phase proportion and component dilution of the GMAW-welded joints of clad steel plate can be effectively controlled to yield joints with good mechanical properties and corrosion resistance.

Investigate Weld Quality of Gas Metal Arc Welding Process Through Online Monitoring of Input Parameters

Gas metal arc welding(GMAW)is also referred as the metal inert gas(MIG)welding which is a process of welding done by the formation of an electric arc between the consumable wire electrode and the workpiece.Through the welding process,a continuous flow of inert gas is supplied,and it avoids the weld being subjected to react with atmospheric air.The process can be automatic or semi-automatic where the main input parameters like current and the voltage can be direct and constant,respectively.Not only the current and voltage the welding quality depends on some more input parameters such as arc gap,velocity,and temperature.In this paper,we explain about a setup which is capable of real-time monitoring of input parameters mentioned above and selecting the best MIG welding parameters for the mild steel.The setup is composed of several sensors and microcontrollers for the collection and the measurement of the input parameters.The samples were categorized according to the federate and the voltage adjustment of the selected welding machine.Then the final objective was to identify the samples of the weld with different parameter changes which are monitored through the system.For the analysis,the samples were subjected to tensile and hardness tests,and microstructure tests to find the dependence of the input parameters which effect for the weld quality.Finally,the experimental results verified the effectiveness of the system for the selection of the quality weld.

Arc and Droplet Behaviors in Horizontal Short-Arc Pulsed Gas Metal Arc Welding of 9%Ni Steel with ERNiCrMo-3 Welding Wire

Short-arc pulsed gas metal arc welding(P-GMAW)was used to solve the dificulties of molten pool spreading and droplet transfer of Ni-based welding wire.Suppression of short-circuit current was used to reduce spatter.Arc length stabilizer was used to acquire a proper and stable arc length maintained at the critical position where short circuit starts to occur.Short-arc P-GMAW with or without arc length stabilizer was compared.The droplet transfer,arc behaviors and weld bead profiles were investigated and compared based on the high-speed photography and observation of weld cross-section.When the arc length stabilizer was deactivated,the arc length was unstable and too short.The droplet transfer mode was mainly short circuit partial transfer,with only a small part of the droplet transferred into the molten pool,with the characteristics of no obvious necking,a few spatters,small droplet impact,long short circuit duration and high short-circuit current.There was also a small proportion of short circuit complete transfer with obvious necking,larger droplet impact,shorter short-circuit duration and lower short-circuit current.With arc length stabilizer,droplet transfer modes were short circuit complete transfer and spray transfer.The spray transfer had the largest droplet impact,no short circuit and no spatter.With the arc length stabilizer activated,a deep penetration,a high penetration ratio,a small reinforcement and a large reinforcement factor were acquired.This provides an innovative method to solve the difficulties of droplet transfer and molten pool spreading and eliminate the incomplete fusion in the GMAW of 9%Ni steel with nickel-based alloy welding wire.

Arc characteristics of submerged arc welding with stainless steel wire

The arc characteristics of submerged arc welding （SAW） with stainless steel wire were studied by using Analysator Hannover （AH）. The tests were carded out under the same preset arc voltage combined with different welding currents. By comparing the probability density distribution （PDD） curves of arc voltage and welding current, the changes were analyzed, the metal transfer mode in SAW was deduced, and the characteristics of a stable arc were summarized. The analysis results show that, with an increase of welding parameters, the short-circuiting peak in the PDD curves of arc voltage decreases gradually until it disappears, and the dominant metal transfer mode changes from flux-wall guided transfer to projected transfer and then to streaming transfer. Moreover, when the PDD curves of arc voltage are both unimodal and generally symmetrical, the greater the peak probability and the smaller the peak span, the more stable the arc becomes.

Fatigue life prediction of gas metal arc welded crucifrom joints of AA7075 aluminium alloy failing from root region

Empirical relationship was developed to predict the fatigue life of gas metal arc welded （GMAW） cruciform joints failing from root region. High strength, age hardenable aluminium alloy of AA7075-T6 grade was used as the base material. The design of experiments concept was used to optimize the required number of fatigue testing experiments. Fatigue experiment was conducted in a servo hydraulic controlled fatigue testing machine under constant amplitude loading. The empirical relationship was developed. By using the developed empirical relationship, the fatigue life of GMAW cruciform joints failing from root region was predicted at 95% confidence level. The effect of cruciform joint dimensions on fatigue life was discussed in detail.

Effect of Ti-Si-Mg-Al wire on microstructure and mechanical properties of plasma arc in-situ welded joint of SiC_p/Al composites

The influence of Ti-Si-Mg-AI wire on microstructure and mechanical properties of SiCp/A1 metal matrix composite joints produced by plasma arc in-situ weld-alloying was investigated. Argon-nitrogen mixture was used as plasma gas and Ti-Si-Mg-A1 flux-cored wires as filled composites. Weldments were submitted to tensile test. Meanwhile, the macro morphology and microstructure of the joints were examined. The result shows that the formation ofneedie-like harmful phase A14C3 is effectively inhibited and the wettability of molten pool is improved by adding Ti-Si-Mg-A1 flux-cored wires. With 15Ti-5Si-5Mg-A1 flux-cored wire as filled composite, the maximum tensile strength of the welded joint is 267 MPa, which is up to 83% that of the matrix composites under annealed condition.

Effect of combinative addition of Ti and Sr on modification of AA4043 welding wire and mechanical properties of AA6082 welded by TIG welding

To improve the mechanical properties of AA6082 weld welded by tungsten inert gas welding using AA4043 welding wire, the effect of addition of Ti and/or Sr on continuous cast and rolled AA4043 welding wire was investigated. Experimental results indicated that Ti and Sr are excellent modifiers, which improve the microstructure of the AA4043 welding wire and enhance the mechanical properties of the AA6082 weld. It was found that the combinative addition of Ti and Sr can effectively modify both the α（Al） dendrites and eutectic Si phases compared with individual addition of Ti or Sr. In addition, Ti and/or Sr also changed the microstructure of the AA6082 weld. The tensile strength of the AA6082 weld reached the maximum value when 0.08% Ti and 0.025% Sr were added simultaneously. These results indicate that the combinative addition of Ti and Sr can be an effective composite modifier.

Arc characteristics of GMA welding in high-pressure air condition

Gas metal arc （ GMA ） welding process can be fluently executed under the range of 0. 1 - 0. 7 MPa air pressure shielded by C02 and ArS0% ＋ CO220% gases, which were tested by the igniting and exploding experiments using a hyperbaric chamber to simulate the underwater conditions. The arc voltage characteristics of the GMA welding were tested in hyperbaric conditions to discover the law of the welding arc affected by environmental pressure, welding current, stick-out, gas type and gas-flow. The experimental results and related discussion are also given in this paper. Finally, a mathematical model was calculated under high-pressure air condition based on the experimental data with the least square approximation method.