A Study on the Effect of Low Calcium Ultra-fine Fly Ash as a Partial Sustainable Supplementary Material to Cement in Self-compacting Concrete

The aim and scope of the present study were to determine the efficacy of UFFA in evaluating the workability,static and dynamic stabilization properties,retention period,and slump loss of SCC systems in their fresh state,as well as their compressive strength at various ages.Microstructure(SEM and XRD)of blended SCC systems were studied.Also,the thermogravimetry behavior of blended SCC specimens were researched.According to the evaluated results,incorporating up to 20%UFFA into fresh concrete improved its performance due to its engineered fine particle size and spherical geometry,both of which contribute to the enhancement of characteristics.Blends of 25%and 30%of UFFA show effect on the water-binder ratio and chemical enhancer dosage,resulting in a loss of homogeneity in fresh SCC systems.The reduced particle size,increased amorphous content,and increased surface area all contribute to the pozzolanic reactivity of the early and later ages,resulting in denser packing and thus an increase in compressive strength.The experimental results indicate that UFFA enhances the properties of SCC in both its fresh and hardened states,which can be attributed to the particles’fineness and their relative effect on SCC.

Effect of CSH Crystal Nucleus on Steam-Free Cured Fly Ash Precast Concrete Components

The measures of steam curing and early-strengthening agents to promote the precast components to reach the target strength quickly can bring different degrees of damage to the concrete.Based on this,the new nanomaterial CSH-the hydration product of cement effectively solves these measures’disadvantages,such as excessive energy consumption,thermal stress damage,and the introduction of external ions.In this paper,the effect of CSH on the early strength of precast fly ash concrete components was investigated in terms of setting time,workability,and mechanical properties and analyzed at the microscopic level using hydration temperature,XRD,and SEM.The results showed that under the same workability,CSH could significantly reduce the amount of admixture,shorten the final setting time,almost not affect the initial setting time,and accelerate the hydration of cement.At the optimum dose of 5%,the mechanical properties of the specimens were improved by more than 98%within 12 h of hydration,resulting in an earlier release time of 12 h and no risk of strength inversion later.The results of this paper give theoretical support to the behavior of precast components under steam-free curing.

Analysis of the Performances and Optimization of Polyurethane Concrete with a Large Percentage of Fly Ash

The properties of polyurethane concrete containing a large amount of fly ash are investigated,and accordingly,a model is introduced to account for the influence of fly ash fineness,water ratio,and loss of ignition(LOI)on its mechanical performances.This research shows that,after optimization,the concrete has a compressive strength of 20.8 MPa,a flexural strength of 3.4 MPa,and a compressive modulus of elasticity of 19.2 GPa.The main factor influencing 28 and 90 d compressive strength is fly ash content,water-binder ratio,and early strength agent content.

BOND PERFORMANCE EXPERIMENT FOR FLY ASH CONCRETE AND STEEL BAR

The impact of fly ash content on bond performance of steel bars and their surrounding concrete is studied by means of sticking strain gauges on steel bars. The average bond stress-slip curves, the steel strain-anchor location curves, and the bond stress-anchor position curves of the pullout specimens with various fly ash contents are obtained. Results indicate that the bond performance of concrete and steel bars can be improved and the distribution of steel strain along the anchorage length tends to be more uniform by adding fly ash in concrete specimens, and both ultimate bond stress and ultimate slip deformation increase the most when 20% of specimens′ content is fly ash.

High-Volume Fly Ash Concrete-A Relevant Step to Sustainable Development

HVFA （high-volume fly ash） concrete could be a sustainable way for by-product utilization to conserve natural resources and protect environment. HVFA concrete can play the role of a high-performance material that may be comparable to the conventional Portland cement concrete. The results of the research programme concerning the relationships between the composition of concrete （w/b ratio, fly ash content and type of cement） and their physical and mechanical properties are presented and discussed in the paper. It is found that the introduction of high-volume fly ash into concrete has caused a decrease in compressive strength at the early age of storage. The significant increase in strength was observed between 28 days and 90 days of curing. The high-volume fly ash concretes were characterized with lower water absorbability and sorptivity than control concrete.

Compressive Strength, Pore Size Distribution and Chloride-ion Penetration of Recycled Aggregate Concrete Incorporating Class-F Fly Ash

The effects of fly ash on the compressive strength, pore size distribution and chloride-ion penetration of recycled aggregate concrete were investigated. Two series of concrete mb：tures were prepared. The concrete mixtures in series I had a water-to-binder ratio and a cement content of 0.55 and 410 kg/ m^3 , respectively. The concrete rnixtures in series II had a water-to-binder ratio and a cement content of 0.45 and 400 kg/ ml respectively. Recycled aggregate was ased as 20% , 50% , and 100% replacements of natural coarse aggregate in the concrete mixtures in both series. In cutdition, fly ash was used as 0% , 25% and 35% by weight replacements of cement. The results show that the compressive strengths of the concrete decreased as the recycled aggregate and the fly ash contents increased. The total porosity and average porosity diameter of the concrete increased us the recycled aggregate content increased. Furtherrruore , an increase in the recycled aggregate content decreased the resistance to chloride ion penetration. Nevertheless, the replacement of cement by 25% fly ush improved the resistance to chloride ion penetration and pore diameters and reduced the total porosity of the recycled aggregate concrete.

Influence of fly ash on early-age cracking behavior of high-flowing concrete

The effects of quality and content of fly ash on the early-age cracking behavior of high-flowing concrete （HFC） were investigated. The early-age cracking behavior of the HFC was analyzed by combining the tests of evaporation capacity and electrical resistivity of the HFC. In these tests, a modified flat-type specimen was adopted. The results show that the HFC will have a lower evaporation capacity when it is mixed with fine fly ash, while it will have a higher evaporation capacity when grade II! fly ash is used as mineral admixture. And the electrical resistivity rate of HFC reduces with the increase of the content of fly ash. A nonlinear relationship exists between the cracking time of HFC and the minimum electrical resistivity. The early-age cracking behavior of HFC with fly ash can be enhanced by appropriately increasing the fine particle content and MgO, K2O, and SO3 contents of fly ash. The optimal content of fly ash, which makes a satisfied early-age cracking behavior of HFC, is obtained. And when the content of fly ash exceeds a critical value, the early-age cracking behavior of HFC will rapidly decrease.

Effect of Fly Ash on Frost-Resistance and Chloride Ions Diffusion Properties of Marine Concrete

It is necessary to pay more attention to the durability of concrete undergoing freeze-thaw cycles and seawater attack simultaneously.Investigated are the effects of water-binder ratio,fly ash（FA）contents and air-entraining agent on resistance to frost and chloride diffusion of marine concrete blended with FA in natural seawater.The results show that fly ash does not improve the frost resistance of concrete but can improve its resistance to chloride diffusion by addition of less than 30%.The resistance to frost and chloride diffusion of FA concrete can be improved with the decrease of water-binder ratio,and FA may improve both of them simultaneously only being mixed with air-entraining agent.A ratio（named as R）of the frost-resisting durability factor to chloride diffusion coefficient can be used to evaluate the durability of marine concrete.Scanning electron microscope（SEM）analyses are consistent with the evaluations by the value of R.

Preparation of Reactive Powder Concrete Using Fly Ash and Steel Slag Powder

To decrease the cement and SF content of RPC by using ultra-fine fly ash （UFFA） and steel slag powder （SS）, the effect of these mineral admixtures on compressive strength of RPC were investigated. The experimental results indicate that the utilization of UFFA and SS in RPC is feasible and has prominent mechanical performance. The microstructure analysis （SEM and TG-DTG-DSC） demonstrated that the excellent mechanical properties of RPC containing SS and UFFA were mainly attributed to the sequential hydration filling effect of the compound system.

Cellular lightweight concrete containing high-calcium fly ash and natural zeolite

Cellular lightweight concrete （CLC） with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement （OPC）, fly ash （FA）, or natural zeolite （NZ）, and its compressive strength, setting time, water absorption, and microstructure of were tested. High-calcium FA and NZ with the median particle sizes of 14.52 and 7.72 μm, respectively, were used to partially replace OPC at 0, 10wt%, 20wt%, and 30wt% of the binder （OPC and pozzolan admixture）. A water-to-binder mass ratio （W/B） of 0.5 was used for all mixes. The testing results indicated that CLC containing 10wt% NZ had the highest compressive strength. The replacement of OPC with NZ decreased the total porosity and air void size but increased the capillary porosity of the CLC. The incorporation of a suitable amount of NZ decreased the setting time, total porosity, and pore size of the paste compared with the findings with the same amount of FA. The total porosity and cumulative pore volume decreased, whereas the gel and capillary pores increased as a result of adding both pozzolans at all replacement levels. The water absorption increased as the capillary porosity increased; this effect depended on the volume of air entrained and the type or amount of pozzolan.

Chloride diffusivity in flexural cracked Portland cement concrete and fly ash concrete beams

In order to examine the effect of load-induced transverse cracks on the chloride penetration in flexural concrete beams, two different concretes, Portland cement concrete(PCC) and fly ash concrete(FAC), were tested with various crack widths. Total 14 reinforced concrete(RC) beams, ten of which were self-anchored in a three-point bending mode, were immersed into a 5% NaCl solution with the condition of dry-wet cycles. Then, the free chloride ion contents were determined by rapid chloride testing(RCT) method. Based on the proposed analytical models of chloride penetration in sound and cracked concrete subjected to dry-wet cycles, the apparent chloride diffusion coefficient and chloride diffusivity of concrete were discussed. It can be found that the performance of chloride diffusivity in both concretes will be improved with the increase of crack width, and that the influence of convection action will also be augmented. Based on the two samples obtained in sound concrete after 15 and 30 cycles, the time-exponent, m, for chloride diffusion coefficient was determined to be 0.58, 0.42, 0.62 and 0.77 for PCC1, PCC2, FAC1 and FAC2 specimens, respectively. Finally, two influencing factors of fly ash content and crack width on chloride diffusivity were obtained by regression analysis of test data, and it can be seen that factors kf and kw can be expressed with quadratic polynomial functions of fly ash content, f, and crack width, w, respectively.

Recycled Aggregate Pervious Concrete: Analysis of Influence of Water-Cement Ratio and Fly Ash under Single Action and Optimal Design of Mix Proportion

Pervious concrete is recommended,which is of great benefit to the ecological environment and human living environment.In this paper,the influences of five water-cement ratios and four fly ash contents to replace the cement by mass with a water-cement ratio of 0.30 on the properties of Recycled Aggregate Pervious Concrete(RAPC)were studied.Following this,based on the Grey relational-Technique for Order Preference by Similarity to an Ideal Solution(TOPSIS)optimization method,the strength,permeability,abrasion loss rate,and material costs of RAPC were adopted as evaluation indices to establish a mix proportion optimization model.The results show that the increase of water-cement ratio and fly ash replacement level of RAPC leads to decreased compres-sive strength while an increase in the permeability and abrasion loss rate.According to test results based on the optimal model 0.30 was identified as the best mix proportion.In addition,ecological-economic analysis of RAPC raw materials was carried out by comparing different natural aggregates.The results of EE(embodied energy)and ECO 2e(embodied CO_(2) emission)pointed out that the combination of recycled aggregate and fly ash leads to sig-nificant ecological and economic benefits.

Durability of Seawater Mixed Concrete with Different Replacement Ratio of BFS （Blast Furnace Slag） and FA （Fly Ash）

Using seawater in concrete can be considered as one of the sustainable approaches in construction industry not only to save the freshwater resource but also to promote the use of abandoned seawater resource, especially in the construction at the uninhabited area close to the sea where the procurement of fresh water is difficult. In this study, durability against chloride attack of seawater mixed concrete with different replacement ratio of BFS （blast furnace slag） and FA （fly ash） is discussed and the life time until the occurrence of corrosion crack is evaluated. The results show that： （1） Chloride penetration rate of seawater mixed specimens with BFS and FA is lower than that of freshwater mixed OPC （ordinary Portland cement） specimens; （2） Oxygen permeability of seawater mixed specimens with BFS and FA is almost the same or lower than that of freshwater mixed OPC specimens; （3） Total life time （corrosion incubation period and propagation period） of seawater mixed specimens with BFS and FA is almost the same or only slightly shorter than that of freshwater mixed OPC specimens. From the results, it was confirmed that the usage of seawater in concrete mixing is feasible in concrete with the appropriate BFS and FA replacement ratio.

Effects of GH Admixture on the Early Strength of Fly Ash Concrete and Mortar

The enhancement effects of GH admixture on the early strengths of fly ash concrete and mortar were studied, and the mechanism was analyzed by X-ray diffraction （XRD） and scanning electro microscope （SEM）. Experimental results show that, by the incorporation of GH admixture, both of cement hydration and pozzolanic reaction of fly ash are accelerated, the strengths of fly ash concrete and mortar are enhanced noticeably, especially the early strength. With a mixture design of 200 kg/m^3 OPC （Ordinary Portland Cement ）, 200 kg/m^3 fly ash and 50 kg/m^3 GH admixture, the strength of concrete at 1 d, 3 d and 28 d reaches 25 MPa, 50 MPa and 70 MPa respectively.

Preparation and Properties of Eco-Friendly Aerated Concrete Utilizing High-Volume Fly Ash with MgO and CaO Activators

The associated MgO in limestone is believed to affect the volume stability of cementitious materials at room tem-perature,which limits the utilization of low grade limestone.In this study,MgO was used as an alkali activator instead of partial CaO to prepare the aerated concrete under hydrother mal conditions.The expansion process was studied to evaluate the influence of the raw materials on the gas forming stability of the slurry.The pore structure(porosity,pore size and its distribution)was analyzed by the image method.The physic mechanical properties(density,strength,thermal properties)of concrete with the addition of MgO were comprehensively investigated.Besides,the mineral compositions and morphology of the hydration products were analyzed to demonstrate the infuence mechanism of MgO on the mechanical properties.Experimental results show that the final expansion rate of the slurry decreases with MgO content.A reasonable MgO content,ie,MgO/(MgO+CaO)<20%,con-tributes to improve the compressive strength,attributing to an increased reaction rate to C-S-H gel and tobermor-ite.The addition of MgO causes the thermal conductivity and specific heat to increase.The pore structure is mainly related to the amount of air entraining agent.This study has a significance for the further utilization of magnesium-rich carbonates in the autoclaved building products.

Two-and Three-Dimensional Chloride Ingress into Fly Ash Concrete

2D,3D chloride ion concentration at the edge and corner zones were systematically investigated for fly ash concretes made with different cement replacement percentage by fly ash （0%,10%,20%,40%,60%）,water to binder ratios （0.3,0.35,0.4）,and curing ages （28 d,90 d）.An interaction effect caused by 2D and 3D diffusion could obviously be observed through the comparison with 1D testing results.In order to quantify the interaction effect,2D and 3D diffusion interaction coefficients was proposed in this paper.Finally,the changes of 2D and 3D interaction coefficients with the change in the free chloride ion concentration were given.The above research provide an insight into chloride ion attack on the edge and corner reinforcing bars of concrete structures in the field of civil engineering.

Assessment of Curing Efficiency and Effect of Moist Curing on Performance of Fly Ash Concrete

This study was conducted to evaluate the sensitivity of compressive strength,water permeability and electrical resistance of near-surface layer concrete with different fly ash contents to curing conditions.It is shown that the sensitivity to curing condition and fly ash content descends in the following order：difference between internal and surface resistivity （ρ） at 28 days,water permeability and compressive strength;both of longer duration of moist curing and use of fly ash in concrete enhanced the water penetration resistance.It is indicated that the resistivity difference ρ at 28 days can reflect accurately the curing history of fly ash concrete regardless of mix proportions;and use of fly ash in concrete requires longer moist curing duration.

Effect of Fly Ash and Early Strength Agent on Durability of Concrete Exposed to the Cyclic Sulfate Environment

The effect of fly ash and early strength agent on resistance of concrete to the cyclic sulfate environment was studied.Concrete specimens made with ordinary portland cement or ordinary portland cement incorporating fly ash with the replacement of 10% or 20%,or 1% early strength agent and fly ash with the replacement of 20%,were made and subjected to 250 cycles of exposure to the cyclic sulfate environment.Concrete properties including loss of mass,chloride ion diffusion coefficient,compressive strength and flexural strength were measured.Microstructure and chemical component of samples were determined by means of X-ray diffraction,scanning electron microscopy and energy dispersive spectroscopy.The experimental results indicated that effect of fly ash on the cyclic sulfate resistance of concretes was mostly dependent on the amount of fly ash.Early strength agent improved performances of concrete with 20% fly ash exposed to cyclic sulfate environment.

Research on the influence of the fly ash on the concrete carbonation

The influence of fly ash on the fresh properties, mechanical properties and carbonation properties were studied in this paper. The performance of a kind of curing agent which was applied to the hardened concrete surface was evaluated. Incorporating large volume of fly ash will risk the concrete carbonation. The curing agent could prevent the concrete carbonation, and the mechanism was explained.

Comparison of High Performance Fly Ash Concrete Using Nano Silica Fume on Different Mixes

This paper investigates the experimental results on the effect of nano silica fume on compressive strength development of concretes containing high volume fly ash (HVFA). The effect of various silica fumes contents such as 1%, 2% & 3% (wt. %) as partial replacement of cement on the compressive strength of cements is evaluated in the first part. The nano silica fume content which exhibits the highest compressive strength above is used in high volume fly ash concretes containing 30% and 50% class F fly ash. The results show that among three different silica fumes contents, the addition of 1% increases the compressive strength of concretes. The addition of 1% silica fume also increases the early age and 28 days compressive strengths of HVFA concretes.