Silicon carbide （SIC） foams with a continuously connected open-cell structure were prepared and characterized for their mechanical performance. The apparent densities of SiC foams were controlled between about 0.4 a...Silicon carbide （SIC） foams with a continuously connected open-cell structure were prepared and characterized for their mechanical performance. The apparent densities of SiC foams were controlled between about 0.4 and 2.3 g/cm^3, with corresponding compressive strengths ranging from about 23 to 60 MPa and flexural strengths from about 8 to 30 MPa. Compressive testing of the SiC foams yielded stress-strain curves with only one linear-elastic region, which is different from those reported on ceramic foams in literature. This can possibly be attributed to the existence of filaments with fine, dense and high strength microstructures. The SiC and the filaments respond homogeneously to applied loading.展开更多
In this study, a series of flame-retardant polyisocyanurate-polyurethane (PIR-PUR) foams were prepared using various concentrations (0-25% by weight) of expandable graphite (EG) and dimethyl methyl phosphonate (DMMP) ...In this study, a series of flame-retardant polyisocyanurate-polyurethane (PIR-PUR) foams were prepared using various concentrations (0-25% by weight) of expandable graphite (EG) and dimethyl methyl phosphonate (DMMP) (0-7% by weight). The effect of these additives on the properties of the PIR-PUR foams, including physico-mechanical, morphological, flame retardancy, and thermal stability, was studied. Increasing amounts of EG in the PIR-PUR foam caused a significant drop in the compression strength. However, DMMP caused the mechanical properties of PIR-PUR foam to improve compared to foam filled with EG alone. The flame retardancy of PIR-PUR foams containing both EG and DMMP was enhanced significantly compared to EG filled foams. Thermogravimetric analysis (TGA) indicated that EG enhances the thermal stability of PIR-PUR foams but that DMMP decreased it. The morphology of the residual char provided conclusive evidence for the weak thermal stability of foams filled with DMMP.展开更多
The properties orAl based nanocomposite metal foams and their corrosion behaviors were investigated in this study. For this, the composite metal foams with different relative densities （porosity） reinforced with alu...The properties orAl based nanocomposite metal foams and their corrosion behaviors were investigated in this study. For this, the composite metal foams with different relative densities （porosity） reinforced with alumina nanoparticles were prepared using a powder me- tallurgy-based sintering-dissolution process （SDP） and NaC1 particles were used as space holders. Then, the effect of nanoparticle rein- forcement and different amounts of NaC1 space holders （corresponding porosity） on the microstructure, morphology, density, hardness, and electrochemical specifications of the samples were investigated. It was found that as the relative density increased from 60% to 70%, the wall thickness increased from about 200 to 300 pro, which led to a decrease in pore size. Also, the addition of nanoparticle reinforcement and the increased relative density result in increasing metal foam hardness. Moreover, electrochemical test results indicated that increasing the A1203 content reduced the corrosion rate, but increasing the porosity enhanced it.展开更多
The vesicant problem during the process of preparing closed-cell aluminum foam by molten body transitional foaming process was discussed and the effect of granularity and addition of TiH2on porosity of closed-cell alu...The vesicant problem during the process of preparing closed-cell aluminum foam by molten body transitional foaming process was discussed and the effect of granularity and addition of TiH2on porosity of closed-cell aluminum foam was investigated. The static compressive behavior of closed-cell aluminum foam and the influence of porosity on static compressive property of closed-cell aluminum foam were researched as well. The results show that with increasing granularity of TiH2,the porosity of closed-cell aluminum foam firstly increases and then decreases gradually, the granularity should be controlled in the range of 38-74μm which can result in higher porosity. The porosity of closed-cell aluminum foam increases with the increasing addition of TiH2, and the addition of TiH2 should be controlled from 1.5% to 2.5% which can result in homogeneous cell and moderate strength of closed-cell aluminum foam. The compressive process of closed-cell aluminum foam obviously displays linear elastic phase, plastic collapse phase, and densification phase, and the compressive strength grows with decreasing porosity.展开更多
The applicability of ultrasonic pulse velocity （UPV） method to in-situ monitor setting and hardening process of foamed concrete （FC） was systematically investigated. The UPVs of various FC pastes were automaticall...The applicability of ultrasonic pulse velocity （UPV） method to in-situ monitor setting and hardening process of foamed concrete （FC） was systematically investigated. The UPVs of various FC pastes were automatically and continuously measured by a specially designed ultrasonic monitoring apparatus （UMA）. Ultrasonic tests were performed on FC mixtures with different density （300, 500, 800 and 1 000 kg/m3）, and different fly ash contents （0%, 20%, 40% and 60%）. The influence of curing temperatures （20, 40, 60 and 80~C） was also studied. The experimental results show that three characteristic stages can be clearly identified during the setting process of an arbitrary FC paste： dormant stage, acceleration stage, and deceleration stage. Wet density, fly ash content, and curing temperature have great impact on setting behavior. A stepwise increase of the wet density results in shorter dormant stage and larger final UPV. Hydration reaction rate is obviously promoted with an increase in curing temperature. However, the addition fly ash retards the microstn,lcture formation. To aid in comparing with the ultrasonic results, the consistence spread test and Vicat needle test （VNT） were also conducted. A correlation between ultrasonic and VNT results was also established to evaluate the initial and final setting time of the FC mixtures. Finally, certain ranges of UPV with reasonable widths were suggested for the initial and final setting time, respectively.展开更多
High-density polyethylene/carbon black foaming conductive composites were prepared from acetylene black（ACEY） and super conductive carbon black（HG-1P） as conductive filler, low-density polyethylene（LDPE） as the ...High-density polyethylene/carbon black foaming conductive composites were prepared from acetylene black（ACEY） and super conductive carbon black（HG-1P） as conductive filler, low-density polyethylene（LDPE） as the second component, ethylene-vinyl acetate（EVA） and ethylene propylene rubber（EPR） as the third component, azobisformamide（AC） as foamer, and dicumyl peroxide（DCP） as cross-linker. The structure and resistivity-temperature behavior of high-density polyethylene（HDPE）/CB foaming conductive composites were investigated. Influences of carbon black, LDPE, EVA, EPR, AC, and DCP on the foaming performance and resistivity-temperature behavior of HDPE/CB foaming conductive composites were also studied. The results reveal that HDPE/CB foaming conductive composite exhibits better switching characteristic; ACET-filled HDPE foaming conductive composite displays better positive temperature coefficient（PYC） effect; whereas super conductive carbon black（HG-1P）-filled HDPE foaming conductive composite shows better negative temperature coefficient（NTC） effect.展开更多
Quasi-static and compressive fatigue tests on the closed cell Al-Si-Ca alloy foam specimens with three different aspect ratios were performed. It turned out that the onset of cyclic shortening of foam with a lower asp...Quasi-static and compressive fatigue tests on the closed cell Al-Si-Ca alloy foam specimens with three different aspect ratios were performed. It turned out that the onset of cyclic shortening of foam with a lower aspect ratio took place earlier and the fatigue strength was lower compared with the specimen with a higher aspect ratio, although all the dimensions of specimen satisfied the seven times the cell size criterion, while the quasi-static stress-strain curves were almost same having same Young＇s modulus, yield stress and plateau stress. Therefore, the seven times the cell size criterion for the quasi-static compression behavior was not applicable to the fatigue analysis of Al-Si-Ca alloy foam.展开更多
The rheological behavior, thermal properties and foam morphology of linear polypropylene and long chain branching polypropylene prepared through UV irradiation reactive extrusion were studied by rheological test, melt...The rheological behavior, thermal properties and foam morphology of linear polypropylene and long chain branching polypropylene prepared through UV irradiation reactive extrusion were studied by rheological test, melt index test, DSC and supercritical carbon dioxide foaming technology. Rheological test and melt index test confirmed that under UV irradiation and extrusion, adding photo-initiator and cross- linking agent could achieve the purpose of branching, thus improved the melt strength of polypropylene effectively. The DSC results revealed that with the introducing of long chain branching, the melting range of the polypropylene broadened and the crystallization temperature increased. Owing to the introduction of long chain branches, polypropylene exhibited higher melt strength and strain hardening behavior. Compared with linear polypropylene, the foam morphologies of long chain branching polypropylene were more uniform.展开更多
The compressive behavior, energy absorption and damping capacity of Al 28% Zn alloy foam, Al 10% Mg alloy foam and commercial pure aluminum foam with open cell were investigated. The Al 28 % Zn alloy foam exhibits the...The compressive behavior, energy absorption and damping capacity of Al 28% Zn alloy foam, Al 10% Mg alloy foam and commercial pure aluminum foam with open cell were investigated. The Al 28 % Zn alloy foam exhibits the typical deformation behavior of brittle foam in static compression, and a much higher energy absorption capacity than the Al 10%Mg alloy foam and pure aluminum foam to the densification strain. Over a large plastic strain range, the energy absorption efficiency of the Al 28 % Zn alloy foam keeps nearly constant and above 80%. The experiments on the internal friction of the three foams are also conducted on a multifunction internal friction apparatus (MFIFA). The Al 28%Zn alloy foam exhibits a high damping capacity which is three to four times larger than those of the pure aluminum foam and Al 28%Mg alloy foam around room temperature. The mechanism for the high damping capacity of the foamed Al 28%Zn alloy may be associated with the viscous sliding at the interface between the soft phase α and the brittle rich Zn phase η in its base metal during vibration.展开更多
文摘Silicon carbide （SIC） foams with a continuously connected open-cell structure were prepared and characterized for their mechanical performance. The apparent densities of SiC foams were controlled between about 0.4 and 2.3 g/cm^3, with corresponding compressive strengths ranging from about 23 to 60 MPa and flexural strengths from about 8 to 30 MPa. Compressive testing of the SiC foams yielded stress-strain curves with only one linear-elastic region, which is different from those reported on ceramic foams in literature. This can possibly be attributed to the existence of filaments with fine, dense and high strength microstructures. The SiC and the filaments respond homogeneously to applied loading.
基金supported by the State Key Program of Coal Joint Funds of National Natural Science Foundation of China (No.51134020)the Natural Science Foundation of Shandong Province(No. ZR2011EL036)the High School Science & Technology Fund Planning Project of Shandong Province (No. JIILD53)
文摘In this study, a series of flame-retardant polyisocyanurate-polyurethane (PIR-PUR) foams were prepared using various concentrations (0-25% by weight) of expandable graphite (EG) and dimethyl methyl phosphonate (DMMP) (0-7% by weight). The effect of these additives on the properties of the PIR-PUR foams, including physico-mechanical, morphological, flame retardancy, and thermal stability, was studied. Increasing amounts of EG in the PIR-PUR foam caused a significant drop in the compression strength. However, DMMP caused the mechanical properties of PIR-PUR foam to improve compared to foam filled with EG alone. The flame retardancy of PIR-PUR foams containing both EG and DMMP was enhanced significantly compared to EG filled foams. Thermogravimetric analysis (TGA) indicated that EG enhances the thermal stability of PIR-PUR foams but that DMMP decreased it. The morphology of the residual char provided conclusive evidence for the weak thermal stability of foams filled with DMMP.
文摘The properties orAl based nanocomposite metal foams and their corrosion behaviors were investigated in this study. For this, the composite metal foams with different relative densities （porosity） reinforced with alumina nanoparticles were prepared using a powder me- tallurgy-based sintering-dissolution process （SDP） and NaC1 particles were used as space holders. Then, the effect of nanoparticle rein- forcement and different amounts of NaC1 space holders （corresponding porosity） on the microstructure, morphology, density, hardness, and electrochemical specifications of the samples were investigated. It was found that as the relative density increased from 60% to 70%, the wall thickness increased from about 200 to 300 pro, which led to a decrease in pore size. Also, the addition of nanoparticle reinforcement and the increased relative density result in increasing metal foam hardness. Moreover, electrochemical test results indicated that increasing the A1203 content reduced the corrosion rate, but increasing the porosity enhanced it.
基金Project (2002AA334060) supported by the Hi-tech Research and Development Program of China
文摘The vesicant problem during the process of preparing closed-cell aluminum foam by molten body transitional foaming process was discussed and the effect of granularity and addition of TiH2on porosity of closed-cell aluminum foam was investigated. The static compressive behavior of closed-cell aluminum foam and the influence of porosity on static compressive property of closed-cell aluminum foam were researched as well. The results show that with increasing granularity of TiH2,the porosity of closed-cell aluminum foam firstly increases and then decreases gradually, the granularity should be controlled in the range of 38-74μm which can result in higher porosity. The porosity of closed-cell aluminum foam increases with the increasing addition of TiH2, and the addition of TiH2 should be controlled from 1.5% to 2.5% which can result in homogeneous cell and moderate strength of closed-cell aluminum foam. The compressive process of closed-cell aluminum foam obviously displays linear elastic phase, plastic collapse phase, and densification phase, and the compressive strength grows with decreasing porosity.
基金Founded by the key laboratory of high performance civil engineering materials(2010CEM002)the National Natural Science Foundation of China(51178106,51138002)+1 种基金the Program for New Century Excellent Talents in University(NCET-08-0116),973 Program(2009CB623200)the Program sponsored for scientific innovation research of college graduate in Jiangsu province(CXLX_0105)
文摘The applicability of ultrasonic pulse velocity （UPV） method to in-situ monitor setting and hardening process of foamed concrete （FC） was systematically investigated. The UPVs of various FC pastes were automatically and continuously measured by a specially designed ultrasonic monitoring apparatus （UMA）. Ultrasonic tests were performed on FC mixtures with different density （300, 500, 800 and 1 000 kg/m3）, and different fly ash contents （0%, 20%, 40% and 60%）. The influence of curing temperatures （20, 40, 60 and 80~C） was also studied. The experimental results show that three characteristic stages can be clearly identified during the setting process of an arbitrary FC paste： dormant stage, acceleration stage, and deceleration stage. Wet density, fly ash content, and curing temperature have great impact on setting behavior. A stepwise increase of the wet density results in shorter dormant stage and larger final UPV. Hydration reaction rate is obviously promoted with an increase in curing temperature. However, the addition fly ash retards the microstn,lcture formation. To aid in comparing with the ultrasonic results, the consistence spread test and Vicat needle test （VNT） were also conducted. A correlation between ultrasonic and VNT results was also established to evaluate the initial and final setting time of the FC mixtures. Finally, certain ranges of UPV with reasonable widths were suggested for the initial and final setting time, respectively.
文摘High-density polyethylene/carbon black foaming conductive composites were prepared from acetylene black（ACEY） and super conductive carbon black（HG-1P） as conductive filler, low-density polyethylene（LDPE） as the second component, ethylene-vinyl acetate（EVA） and ethylene propylene rubber（EPR） as the third component, azobisformamide（AC） as foamer, and dicumyl peroxide（DCP） as cross-linker. The structure and resistivity-temperature behavior of high-density polyethylene（HDPE）/CB foaming conductive composites were investigated. Influences of carbon black, LDPE, EVA, EPR, AC, and DCP on the foaming performance and resistivity-temperature behavior of HDPE/CB foaming conductive composites were also studied. The results reveal that HDPE/CB foaming conductive composite exhibits better switching characteristic; ACET-filled HDPE foaming conductive composite displays better positive temperature coefficient（PYC） effect; whereas super conductive carbon black（HG-1P）-filled HDPE foaming conductive composite shows better negative temperature coefficient（NTC） effect.
基金supported by Chungnam Automotive Technology Education Center(NURI)and BK 21.
文摘Quasi-static and compressive fatigue tests on the closed cell Al-Si-Ca alloy foam specimens with three different aspect ratios were performed. It turned out that the onset of cyclic shortening of foam with a lower aspect ratio took place earlier and the fatigue strength was lower compared with the specimen with a higher aspect ratio, although all the dimensions of specimen satisfied the seven times the cell size criterion, while the quasi-static stress-strain curves were almost same having same Young＇s modulus, yield stress and plateau stress. Therefore, the seven times the cell size criterion for the quasi-static compression behavior was not applicable to the fatigue analysis of Al-Si-Ca alloy foam.
基金Funded by the National Natural Science Foundation of China(No.51103091)Scientific Research Foundation for the Returned Overseas Chinese Scholars State Education Ministry(No.20101174-4-3)the Opening Project of the Key Laboratory of Polymer Processing Engineering,Ministry of Education,China and the Fundamental Research Funds for the Central Universities(No.2012ZM0074)
文摘The rheological behavior, thermal properties and foam morphology of linear polypropylene and long chain branching polypropylene prepared through UV irradiation reactive extrusion were studied by rheological test, melt index test, DSC and supercritical carbon dioxide foaming technology. Rheological test and melt index test confirmed that under UV irradiation and extrusion, adding photo-initiator and cross- linking agent could achieve the purpose of branching, thus improved the melt strength of polypropylene effectively. The DSC results revealed that with the introducing of long chain branching, the melting range of the polypropylene broadened and the crystallization temperature increased. Owing to the introduction of long chain branches, polypropylene exhibited higher melt strength and strain hardening behavior. Compared with linear polypropylene, the foam morphologies of long chain branching polypropylene were more uniform.
文摘The compressive behavior, energy absorption and damping capacity of Al 28% Zn alloy foam, Al 10% Mg alloy foam and commercial pure aluminum foam with open cell were investigated. The Al 28 % Zn alloy foam exhibits the typical deformation behavior of brittle foam in static compression, and a much higher energy absorption capacity than the Al 10%Mg alloy foam and pure aluminum foam to the densification strain. Over a large plastic strain range, the energy absorption efficiency of the Al 28 % Zn alloy foam keeps nearly constant and above 80%. The experiments on the internal friction of the three foams are also conducted on a multifunction internal friction apparatus (MFIFA). The Al 28%Zn alloy foam exhibits a high damping capacity which is three to four times larger than those of the pure aluminum foam and Al 28%Mg alloy foam around room temperature. The mechanism for the high damping capacity of the foamed Al 28%Zn alloy may be associated with the viscous sliding at the interface between the soft phase α and the brittle rich Zn phase η in its base metal during vibration.
