Ordered nanoripples on the niobium-doped SrTiO_3 surfaces were fabricated through focused ion beam bombardment. The surface morphology of the SrTiO_3 nanoripples was characterized using in situ focused ion beam/scanni...Ordered nanoripples on the niobium-doped SrTiO_3 surfaces were fabricated through focused ion beam bombardment. The surface morphology of the SrTiO_3 nanoripples was characterized using in situ focused ion beam/scanning electron microscopy. The well-aligned SrTiO_3 nanostructures were obtained under optimized ion irradiation conditions. The characteristic wavelength was measured as about 210 nm for different ion beam currents. The relationship between the ion irradiation time and current and SrTiO_3 surface morphology was analyzed. The presented method will be an effective supplement for fabrication of SrTiO_3 nanostructures that can be used for ferroelectric and electronic applications.展开更多
Three-dimensional(3D)vertical architecture transistors represent an important technological pursuit,which have distinct advantages in device integration density,operation speed,and power consumption.However,the fabric...Three-dimensional(3D)vertical architecture transistors represent an important technological pursuit,which have distinct advantages in device integration density,operation speed,and power consumption.However,the fabrication processes of such 3D devices are complex,especially in the interconnection of electrodes.In this paper,we present a novel method which combines suspended electrodes and focused ion beam(FIB)technology to greatly simplify the electrodes interconnection in 3D devices.Based on this method,we fabricate 3D vertical core-double shell structure transistors with ZnO channel and Al_(2)O_(3) gate-oxide both grown by atomic layer deposition.Suspended top electrodes of vertical architecture could be directly connected to planar electrodes by FIB deposited Pt nanowires,which avoid cumbersome steps in the traditional 3D structure fabrication technology.Both single pillar and arrays devices show well behaved transfer characteristics with an Ion/Ioff current ratio greater than 106 and a low threshold voltage around 0 V.The ON-current of the 2×2 pillars vertical channel transistor was 1.2μA at the gate voltage of 3 V and drain voltage of 2 V,which can be also improved by increasing the number of pillars.Our method for fabricating vertical architecture transistors can be promising for device applications with high integration density and low power consumption.展开更多
Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation ...Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.展开更多
Three sample preparation techniques, focused ion beam (FIB), ion beam (IB) etching, and ultramicrotomy (UM) were used in comparison to analyze the interphase of carbon fiber 'epoxy composites using transmission...Three sample preparation techniques, focused ion beam (FIB), ion beam (IB) etching, and ultramicrotomy (UM) were used in comparison to analyze the interphase of carbon fiber 'epoxy composites using transmission electron microscopy. An intact interphase with a relatively uniform thickness was obtained by FIB. and detailed chemical analysis of the interphase was investigated by electron energy loss spectroscopy. It shows that the interphase region is 200 mn wide with an increasing oxygen-to-carbon ratio from 10% to 19% and an almost constant nitrogen-to-carbon ratio of about 3%. However, gallium implantation of FIB tends to hinder fine structure analysis of the interphase. For IB etching, the interphase region is observed with transition morphology frona amorphous resin to nano-crystalline carbon fiber, but the uneven sample thickness brings difficulty for quantitative chemical analysis. Moreover, UM tends to cause damage and/or deformation on the interphase. These results are meaningful for in-depth understanding on the interphase characteristic of carbon fiber composites.展开更多
Raman spectroscopy is a type of inelastic scattering spectroscopy that is widely used in determining and analyzing molecular structure.It also has a number of practical applications in evaluating food safety,medicine,...Raman spectroscopy is a type of inelastic scattering spectroscopy that is widely used in determining and analyzing molecular structure.It also has a number of practical applications in evaluating food safety,medicine,and forensics.The Raman spectral signal is weak,but the development of the surface-enhanced Raman scattering(SERS)technique has overcome this problem and led to further developments in Raman spectroscopy.This paper describes a fundamental study of the use of focused ion beam(FIB)direct writing for preparing gold substrates for SERS.Molecular dynamics and Monte Carlo simulation methods are used to investigate the damage induced by gallium ion implantation of a gold substrate.Based on characterization by x-ray photoelectron spectroscopy(XPS)and scanning electron microscopy,the mechanism by which ion implantation and annealing influence the damage induced by a gallium FIB is analyzed.After annealing at 350 XC,a mixture of metallic gallium,its oxide Ga2O3 conforming to the stoichiometric ratio,and its sub-stable oxide(Ga2Ox)in sub-stoichiometric ratio precipitated on the surface are detected by XPS.Annealing treatment can effectively reduce the effect of gallium ion implantation on a SERS substrate fabricated by FIB direct writing.展开更多
The combination of focused ion beam (FIB) with scanning electron microscopy (SEM), also known as FIB-SEM tomography, has become a powerful 3D imaging technique at the nanometer scale. This method uses an ion beam to m...The combination of focused ion beam (FIB) with scanning electron microscopy (SEM), also known as FIB-SEM tomography, has become a powerful 3D imaging technique at the nanometer scale. This method uses an ion beam to mill away a thin slice of material, which is then block-face imaged using an electron beam. With consecutive slicing along the z-axis and subsequent imaging, a volume of interest can be reconstructed from the images and further analyzed. Hierarchical nanoporous gold (HNPG) exhibits unique structural properties and has a ligament size of 15–110 nm and pore size of 5–20 nm. Accurate reconstruction of its image is crucial in determining its mechanical and other properties. Slice thickness is one of the most critical and uncertain parameters in FIB-SEM tomography. For HNPG, the slice thickness should be at least half as thin as the pore size and, in our approach, should not exceed 10 nm. Variations in slice thickness are caused by various microscope and sample parameters, e.g., converged ion milling beam shape, charging effects, beam drift, or sample surface roughness. Determining and optimizing the actual slice thickness variation appear challenging. In this work, we examine the influence of ion beam scan resolution and the dwell time on the mean and standard deviation of slice thickness. After optimizing the resolution and dwell time to achieve the target slice thickness and lowest possible standard deviation, we apply these parameters to analyze an actual HNPG sample. Our approach can determine the thickness of each slice along the z-axis and estimate the deviation of the milling process along the y-axis (slow imaging axis). For this function, we create a multi-ruler structure integrated with the HNPG sample.展开更多
Clock rolling was developed to make defor- mation microstructure homogenize in high-purity Ta. The substructure of deformed Ta was revealed by electron back-scatter diffraction (EBSD) technique aided with triple foc...Clock rolling was developed to make defor- mation microstructure homogenize in high-purity Ta. The substructure of deformed Ta was revealed by electron back-scatter diffraction (EBSD) technique aided with triple focused ion beam (FIB). The results indicate that the triple FIB method can produce a mirror surface required by EBSD analysis. The clock rolling works well for the homogenization of deformed microstructure. Particularly, the local stored energy in { 111 } orientated grains is largely reduced by clock rolling, whereas it is enhanced in {100} orientated grains because of the occurrence of grain subdivision.展开更多
PbTiO_(3)nanorods with tetragonal phase were synthesized by hydrothermal method and heat treatment,and temperature-dependent electrical transport properties of individual PbTiO_(3)nanorod were investigated.The results...PbTiO_(3)nanorods with tetragonal phase were synthesized by hydrothermal method and heat treatment,and temperature-dependent electrical transport properties of individual PbTiO_(3)nanorod were investigated.The results show that the conductivities of PbTiO_(3)nanorods are gradually enhanced with temperature increasing from 77.4 to 295 K,and exhibit the typical nonlinear Ⅰ–Ⅴ char-acteristics.The barrier height between Au electrode and nanorod is reduced from 0.137 to 0.088 eV with increasing bias from 0.2 to 1 V.The corresponding values of thermal activation energies are 0.172 and 0.06 eV below the conduction band for 180–295 and 77.4–180 K,respectively.This semiconductor-like behavior may result from the larger number of surface defects or localized states in the amorphorized PbTiO_(3).展开更多
As a newly developed method for fabricating Josephson junctions,a focused helium ion beam has the advantage of producing reliable and reproducible junctions.We fabricated Josephson junctions with a focused helium ion ...As a newly developed method for fabricating Josephson junctions,a focused helium ion beam has the advantage of producing reliable and reproducible junctions.We fabricated Josephson junctions with a focused helium ion beam on our 50 nm YBa_(2)Cu_(3)O_(7-δ)(YBCO)thin films.We focused on the junction with irradiation doses ranging from 100 to 300 ions/nm and demonstrated that the junction barrier can be modulated by the ion dose and that within this dose range,the junctions behave like superconductor–normal conductor–superconductor junctions.The measurements of the I–V characteristics,Fraunhofer diffraction pattern,and Shapiro steps of the junctions clearly show AC and DC Josephson effects.Our findings demonstrate high reproducibility of junction fabrication using a focused helium ion beam and suggest that commercial devices based on this nanotechnology could operate at liquid nitrogen temperatures.展开更多
Performance degradation shortens the life of solid oxide fuel cells in practical applications.Revealing the degradation mechanism is crucial for the continuous improvement of cell durability.In this work,the effects o...Performance degradation shortens the life of solid oxide fuel cells in practical applications.Revealing the degradation mechanism is crucial for the continuous improvement of cell durability.In this work,the effects of cell operating conditions on the terminal voltage and anode microstructure of a Ni-yttria-stabilized zirconia anode-supported single cell were investigated.The microstructure of the anode active area near the electrolyte was characterized by laser optical microscopy and focused ion beam-scanning electron microscopy.Ni depletion at the anode/electrolyte interface region was observed after 100 h discharge tests.In addition,the long-term stability of the single cell was evaluated at 700℃for 3000 h.After an initial decline,the anode-supported single cell exhibits good durability with a voltage decay rate of 0.72%/kh and an electrode polarization resistance decay rate of 0.17%/kh.The main performance loss of the cell originates from the initial degradation.展开更多
Half-integer microwave induced steps(Shapiro steps)have been observed in many different Josephson junction systems,which have attracted a lot of attention because they signify the deviation of current phase relation(C...Half-integer microwave induced steps(Shapiro steps)have been observed in many different Josephson junction systems,which have attracted a lot of attention because they signify the deviation of current phase relation(CPR)and uncover many unconventional physical properties.In this article,we first report the discovery of half-integer Shapiro steps in MgB_(2)focused He ion beam(He-FIB)Josephson junctions.The half-integer steps'dependence on microwave frequency,temperature,microwave power,and magnetic field is also analyzed.We find that the existence of half-integer steps can be controlled by the magnetic field periodically,which is similar to that of high temperature superconductor(HTS)grain boundary junctions,and the similarity of the microstructures between gain boundary junctions and He-FIB junctions is discussed.As a consequence,we mainly attribute the physical origin of half-integer steps in MgB_(2)He-FIB junctions to the model that a He-FIB junction is analogous to a parallel junctions'array.Our results show that He-FIB technology is a promising platform for researching CPR in junctions made of different superconductors.展开更多
The three-dimensional(3D)pore structures and permeability of shale are critical for forecasting gas production capacity and guiding pressure differential control in practical reservoir extraction.However,few investiga...The three-dimensional(3D)pore structures and permeability of shale are critical for forecasting gas production capacity and guiding pressure differential control in practical reservoir extraction.However,few investigations have analyzed the effects of microscopic organic matter(OM)morphology and 3D pore nanostructures on the stress sensitivity,which are precisely the most unique and controlling factors of reservoir quality in shales.In this study,ultra-high nanoscale-resolution imaging experiments,i.e.focused ion beam-scanning electron microscopy(FIB-SEMs),were conducted on two organic-rich shale samples from Longmaxi and Wufeng Formations in northern Guizhou Depression,China.Pore morphology,porosity of 3D pore nanostructures,pore size distribution,and connectivity of the six selected regions of interest(including clump-shaped OMs,interstitial OMs,framboidal pyrite,and microfractures)were qualitatively and quantitatively characterized.Pulse decay permeability(PDP)measurement was used to investigate the variation patterns of stress-dependent permeability and stress sensitivity of shales under different confining pressures and pore pressures,and the results were then used to calculate the Biot coefficients for the two shale formations.The results showed that the samples have high OM porosity and 85%of the OM pores have the radius of less than 40 nm.The OM morphology and pore structure characteristics of the Longmaxi and Wufeng Formations were distinctly different.In particular,the OM in the Wufeng Formation samples developed some OM pores with radius larger than500 nm,which significantly improved the connectivity.The macroscopic permeability strongly depends on the permeability of OM pores.The stress sensitivity of permeability of Wufeng Formation was significantly lower than that of Longmaxi Formation,due to the differences in OM morphology and pore structures.The Biot coefficients of 0.729 and 0.697 were obtained for the Longmaxi and Wufeng Formations,respectively.展开更多
The influence of oxide scales on the corrosion behaviors of B510 L hot-rolled steel strips was investigated in this study. Focused ion beams and scanning electron microscopy were used to observe the morphologies of ox...The influence of oxide scales on the corrosion behaviors of B510 L hot-rolled steel strips was investigated in this study. Focused ion beams and scanning electron microscopy were used to observe the morphologies of oxide scales on the surface and cross sections of the hot-rolled steel. Raman spectroscopy and X-ray diffraction were used for the phase analysis of the oxide scales and corrosion products. The corrosion potential and impedance were measured by anodic polarization and electrochemical impedance spectroscopy. According to the results, oxide scales on the hot-rolled strips mainly comprise iron and iron oxides. The correlation between mass gain and test time follows a power exponential rule in the damp-heat test. The corrosion products are found to be mainly composed of γ-Fe OOH, Fe3O4, ?-Fe OOH, and γ-Fe2O3. The contents of the corrosion products are different on the surfaces of the steels with and without oxide scales. The steel with oxide scales is found to show a higher corrosion resistance and lower corrosion rate.展开更多
Despite the long-established rocking-chair theory of lithium-ion batteries(LIBs),developing novel characterization methodology with higher spatiotemporal resolution facilitates a better understanding of the solid elec...Despite the long-established rocking-chair theory of lithium-ion batteries(LIBs),developing novel characterization methodology with higher spatiotemporal resolution facilitates a better understanding of the solid electrolyte interphase studies to shape the reaction mechanisms.In this work,we develop a Xenon ion plasma focused ion beam(Xe+PFIB)-based characterization technique to probe the cross-sectional interface of both ternary cathode and graphite anode electrodes,with the focus on revealing the chemical composition and distribution underneath the electrode surface by in-depth analysis of secondary ions.Particularly,the lithium fluoride is detected in the pristine cathode prior to contact with the electrolyte,reflecting that the electrode degradation is in the form of the loss of lithium inventory during electrode preparation.This degradation is related to the hydrolysis of the cathode material and the decomposition of the PVDF binder.Through the quantitative analysis of the transition-metal degradation products,manganese is found to be the dominant element in the newly formed inactive fluoride deposition on the cathode,while no transition metal signal can be found inside the anode electrode.These insights at high resolution implemented via a PFIB-based characterization technique not only enrich the understanding of the degradation mechanism in the LIBs but also identify and enable a high-sensitivity methodology to obtain the chemical survey at the subsurface,which will help remove the capacity-fade observed in most LIBs.展开更多
Human dental hard tissues are dentine, cementum, and enamel. These are hydrated mineralised composite tissues with a hierarchical structure and versatile thermo-mechanical properties. The hierarchical structure of den...Human dental hard tissues are dentine, cementum, and enamel. These are hydrated mineralised composite tissues with a hierarchical structure and versatile thermo-mechanical properties. The hierarchical structure of dentine and enamel was imaged by transmission electron microscopy (TEM) of samples prepared by focused ion beam (FIB) milling. High resolution TEM was carried out in the vicinity of a crack tip in dentine. An intricate "random weave" pattern of hydroxyapatile crystallites was observed and this provided a possible explanation for toughening of the mineralized dentine tissue at the nano-scale. The results reported here provide the basis for improved understanding of the rela- tionship between the multi-scale nature and the mechanical properties of hierarchically structured biomaterials, and will also be useful for the development of better prosthetic and dental restorative materials.展开更多
Focused ion beam(FIB)processing with low-energy ions has become a standard technique for the manipulation of nanostructures.Many underlying ion beam effects that deviate from conventional high-energy ion irradiation o...Focused ion beam(FIB)processing with low-energy ions has become a standard technique for the manipulation of nanostructures.Many underlying ion beam effects that deviate from conventional high-energy ion irradiation of bulk systems are considered today;however,ion channeling with its consequence of significant deeper penetration depth has been only theoretically investigated in this regime.We present here an experimental approach to determine the channeling of low-energy ions in crystalline nanoparticles by measuring the sputter yield derived from scanning electron microscopy(SEM)images taken after irradiation under various incident ion angles.Channeling maps of 30 and 20 keV Ga+ions in Ag nanocubes have been identified and fit well with the theory.Indeed,channeling has a significant impact on the transport of energetic ions in crystals due to the large critical angle at low ion energies,thus being relevant for any FIB-application.Consequently,the obtained sputter yield clearly differs from amorphous materials;therefore,it is recommended not to rely only on,e.g.,ion distribution depths predicted by standard Monte-Carlo(MC)algorithms for amorphous materials.展开更多
Aluminosilicate small pore zeolites belonging to ABC-6 family play crucially important roles in the high methanol conversion with the high selectivity of light olefins,gas separation and storage,and selective catalyti...Aluminosilicate small pore zeolites belonging to ABC-6 family play crucially important roles in the high methanol conversion with the high selectivity of light olefins,gas separation and storage,and selective catalytic reduction of NO_(x).In this work,we report a general method,called the epitaxial growth approach,for designing ABC-6 family small pore zeolites.It is mainly realized through the epitaxial growth on the nonporous SOD-type zeolite in the presence of inorganic cations(Na^(+)and K^(+))combined with a variety of organic structure directing agents(OSDAs).In this case,a series of ABC-6 family small pore zeolites such as ERI-,SWY-,LEV-,AFX-,and PTT-type zeolites have been successfully synthesized within a few hours.More importantly,the advanced focused ion beam(FIB)and the low-dose high-resolution transmission electron microscopy(HRTEM)imaging technique have been utilized for unraveling the zeolite heterojunction at the atomic level during the epitaxial growth process.It turns out(222)crystallographic planes of the SOD-type zeolite substrate provide unique pre-building units,which facilitate the growth of targeted ABC-6 family small pore zeolites along its c-axis.Moreover,the morphologies of ERI-type zeolite can also be tuned through the epitaxial growth approach,achieving a longer lifetime in the methanol conversion.展开更多
The microstructural evolutions of 5Mn steel during various heat treatments have been investiga- ted by in-situ transmission electron microscopy (TEM). The specimen of 5Mn steel was pre- pared using focused ion beam ...The microstructural evolutions of 5Mn steel during various heat treatments have been investiga- ted by in-situ transmission electron microscopy (TEM). The specimen of 5Mn steel was pre- pared using focused ion beam (FIB) milling, which allowed the selection of specific morphology of interest prior to the in-situ observation, The complete austenization at 800 ℃ was verified at the atomic scale by minimizing thermal expansion and sample drift in a heating holder based on micro-electro-mechanical-systems. During annealing at 650 ℃, the formation of reverted austen- ite was dynamically observed, while the morphologies of austenite laths of 5Mn steel after in-situ heating were quite similar to that after ex-situ intereritical annealing. During annealing at 500 ℃, the morphological evolution of cementite and associated Mn diffusion were investigated. It was demonstrated that a combination of FIB sampling and high temperature in-situ TEM enables us to probe the morphological evolution and elemental diffusion of specific areas of interest in steel at high spatial resolution.展开更多
Pb nanobridges with a thickness of less than 10 nm and a width of several hundred nm have been fabricated from single-crystalline Pb fi lms using low-temperature molecular beam epitaxy and focus ion beam microfabricat...Pb nanobridges with a thickness of less than 10 nm and a width of several hundred nm have been fabricated from single-crystalline Pb fi lms using low-temperature molecular beam epitaxy and focus ion beam microfabrication techniques.We observed novel magnetoresistance oscillations below the superconducting transition temperature(TC)of the bridges.The oscillations which were not seen in the crystalline Pb fi lmsmay originate from the inhomogeneity of superconductivity induced by the applied magnetic fi elds on approaching the normal state,or the degradation of fi lm quality by thermal evolution.展开更多
Focused ion beam (FIB) machining can be used to fabricate gallium arsenide-based devices, which have a surface fnish of several nanometers, and the FIB machining speed and surface fnish can be greatly improved using x...Focused ion beam (FIB) machining can be used to fabricate gallium arsenide-based devices, which have a surface fnish of several nanometers, and the FIB machining speed and surface fnish can be greatly improved using xenon difuoride (XeF2) gas-assisted etching. Although the refresh time is one of the most important parameters in the gas-assisted etching process, its efect on the machining quality of the surface fnish has rarely been studied. Therefore, in this work, we investigated the efect of the refresh time on the etching process, including the dissociation process of XeF2, the refresh time dependency of the sputter in yield under diferent incident angles, and the surface fnish under diferent refresh times. The results revealed that a selective etching mechanism occurred at diferent refresh times. At an incidence angle of 0°, the sputtering yield increased with the refresh time and reached its maximum value at 500 ms;at an incidence angle of 30°, the sputtering yield reached its minimum value at a refresh time of 500 ms. For surface roughness, the incident angle played a more important role than the refresh time. The surface fnish was slightly better at an incidence angle of 30° than at 0°. In addition, both F and Xe elements were detected in the processed area: Xe elements were evenly distributed throughout the processing area, while F elements tended to accumulate in the whole processing area. The results suggest that the optimum surface can be obtained when a larger refresh time is employed.展开更多
基金the financial support from the Arkansas Institute for Nanoscience and Engineering at University of Arkansasthe International Centre of Artificial Materials(iCAM)at University of Electronic Science and Technology of China
文摘Ordered nanoripples on the niobium-doped SrTiO_3 surfaces were fabricated through focused ion beam bombardment. The surface morphology of the SrTiO_3 nanoripples was characterized using in situ focused ion beam/scanning electron microscopy. The well-aligned SrTiO_3 nanostructures were obtained under optimized ion irradiation conditions. The characteristic wavelength was measured as about 210 nm for different ion beam currents. The relationship between the ion irradiation time and current and SrTiO_3 surface morphology was analyzed. The presented method will be an effective supplement for fabrication of SrTiO_3 nanostructures that can be used for ferroelectric and electronic applications.
基金the National Key Research and Development Program of China(Grant Nos.2016YFA0200400 and 2016YFA0200800)the National Natural Science Foundation of China(Grant Nos.61888102,12074420,and 11674387)+1 种基金Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB33000000)Key Research Program of Frontier Sciences,Chinese Acdemy of Sciences(Grant No.QYZDJ-SSWSLH042).
文摘Three-dimensional(3D)vertical architecture transistors represent an important technological pursuit,which have distinct advantages in device integration density,operation speed,and power consumption.However,the fabrication processes of such 3D devices are complex,especially in the interconnection of electrodes.In this paper,we present a novel method which combines suspended electrodes and focused ion beam(FIB)technology to greatly simplify the electrodes interconnection in 3D devices.Based on this method,we fabricate 3D vertical core-double shell structure transistors with ZnO channel and Al_(2)O_(3) gate-oxide both grown by atomic layer deposition.Suspended top electrodes of vertical architecture could be directly connected to planar electrodes by FIB deposited Pt nanowires,which avoid cumbersome steps in the traditional 3D structure fabrication technology.Both single pillar and arrays devices show well behaved transfer characteristics with an Ion/Ioff current ratio greater than 106 and a low threshold voltage around 0 V.The ON-current of the 2×2 pillars vertical channel transistor was 1.2μA at the gate voltage of 3 V and drain voltage of 2 V,which can be also improved by increasing the number of pillars.Our method for fabricating vertical architecture transistors can be promising for device applications with high integration density and low power consumption.
基金Project supported by the National Key Research and Development Program of China (Grant Nos.2020YFF01014706 and 2017YFC0601901)the National Natural Science Foundation of China (Grant Nos.61571019 and 52177026)。
文摘Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.
基金supported by the National Natural Science Foundation of China (Grant No. 51273007)the Program for New Century Excellent Talents in University of China (NCET)
文摘Three sample preparation techniques, focused ion beam (FIB), ion beam (IB) etching, and ultramicrotomy (UM) were used in comparison to analyze the interphase of carbon fiber 'epoxy composites using transmission electron microscopy. An intact interphase with a relatively uniform thickness was obtained by FIB. and detailed chemical analysis of the interphase was investigated by electron energy loss spectroscopy. It shows that the interphase region is 200 mn wide with an increasing oxygen-to-carbon ratio from 10% to 19% and an almost constant nitrogen-to-carbon ratio of about 3%. However, gallium implantation of FIB tends to hinder fine structure analysis of the interphase. For IB etching, the interphase region is observed with transition morphology frona amorphous resin to nano-crystalline carbon fiber, but the uneven sample thickness brings difficulty for quantitative chemical analysis. Moreover, UM tends to cause damage and/or deformation on the interphase. These results are meaningful for in-depth understanding on the interphase characteristic of carbon fiber composites.
基金The study is supported by the National Natural Science Foundation of China(Grant No.51575389)the State Key Laboratory of Precision Measurement Technology and Instruments(Pilt1705)。
文摘Raman spectroscopy is a type of inelastic scattering spectroscopy that is widely used in determining and analyzing molecular structure.It also has a number of practical applications in evaluating food safety,medicine,and forensics.The Raman spectral signal is weak,but the development of the surface-enhanced Raman scattering(SERS)technique has overcome this problem and led to further developments in Raman spectroscopy.This paper describes a fundamental study of the use of focused ion beam(FIB)direct writing for preparing gold substrates for SERS.Molecular dynamics and Monte Carlo simulation methods are used to investigate the damage induced by gallium ion implantation of a gold substrate.Based on characterization by x-ray photoelectron spectroscopy(XPS)and scanning electron microscopy,the mechanism by which ion implantation and annealing influence the damage induced by a gallium FIB is analyzed.After annealing at 350 XC,a mixture of metallic gallium,its oxide Ga2O3 conforming to the stoichiometric ratio,and its sub-stable oxide(Ga2Ox)in sub-stoichiometric ratio precipitated on the surface are detected by XPS.Annealing treatment can effectively reduce the effect of gallium ion implantation on a SERS substrate fabricated by FIB direct writing.
基金funded by the Deutsche Forschungsgemeinschaft(DFG,German Research Foundation)—Project SFB 986—Tailor-Made Multiscale Materials Systems,subproject B9—Microstructure-based classification and mechanical analysis of nanoporous metals by machine learningOpen Access funding enabled and organized by Projekt DEAL.
文摘The combination of focused ion beam (FIB) with scanning electron microscopy (SEM), also known as FIB-SEM tomography, has become a powerful 3D imaging technique at the nanometer scale. This method uses an ion beam to mill away a thin slice of material, which is then block-face imaged using an electron beam. With consecutive slicing along the z-axis and subsequent imaging, a volume of interest can be reconstructed from the images and further analyzed. Hierarchical nanoporous gold (HNPG) exhibits unique structural properties and has a ligament size of 15–110 nm and pore size of 5–20 nm. Accurate reconstruction of its image is crucial in determining its mechanical and other properties. Slice thickness is one of the most critical and uncertain parameters in FIB-SEM tomography. For HNPG, the slice thickness should be at least half as thin as the pore size and, in our approach, should not exceed 10 nm. Variations in slice thickness are caused by various microscope and sample parameters, e.g., converged ion milling beam shape, charging effects, beam drift, or sample surface roughness. Determining and optimizing the actual slice thickness variation appear challenging. In this work, we examine the influence of ion beam scan resolution and the dwell time on the mean and standard deviation of slice thickness. After optimizing the resolution and dwell time to achieve the target slice thickness and lowest possible standard deviation, we apply these parameters to analyze an actual HNPG sample. Our approach can determine the thickness of each slice along the z-axis and estimate the deviation of the milling process along the y-axis (slow imaging axis). For this function, we create a multi-ruler structure integrated with the HNPG sample.
基金supported by the National Natural Science Foundation of China (No. 51301212)the Major National Science and Technology Projects of China (No. 2011ZX02705)+1 种基金the Chongqing Science and Technology Commission in China (No. 2012jjA50023)the Fundamental Research Funds for the Central Universities (No. CDJZR11130010)
文摘Clock rolling was developed to make defor- mation microstructure homogenize in high-purity Ta. The substructure of deformed Ta was revealed by electron back-scatter diffraction (EBSD) technique aided with triple focused ion beam (FIB). The results indicate that the triple FIB method can produce a mirror surface required by EBSD analysis. The clock rolling works well for the homogenization of deformed microstructure. Particularly, the local stored energy in { 111 } orientated grains is largely reduced by clock rolling, whereas it is enhanced in {100} orientated grains because of the occurrence of grain subdivision.
基金supported by the National Natural Science Foundation of China(NSFC Grant No.61274073).
文摘PbTiO_(3)nanorods with tetragonal phase were synthesized by hydrothermal method and heat treatment,and temperature-dependent electrical transport properties of individual PbTiO_(3)nanorod were investigated.The results show that the conductivities of PbTiO_(3)nanorods are gradually enhanced with temperature increasing from 77.4 to 295 K,and exhibit the typical nonlinear Ⅰ–Ⅴ char-acteristics.The barrier height between Au electrode and nanorod is reduced from 0.137 to 0.088 eV with increasing bias from 0.2 to 1 V.The corresponding values of thermal activation energies are 0.172 and 0.06 eV below the conduction band for 180–295 and 77.4–180 K,respectively.This semiconductor-like behavior may result from the larger number of surface defects or localized states in the amorphorized PbTiO_(3).
基金supported by the National Key Research and Development Program of China(Grant No.2017YFC0601901)the National Natural Science Foundation of China(Grant No.61571019)。
文摘As a newly developed method for fabricating Josephson junctions,a focused helium ion beam has the advantage of producing reliable and reproducible junctions.We fabricated Josephson junctions with a focused helium ion beam on our 50 nm YBa_(2)Cu_(3)O_(7-δ)(YBCO)thin films.We focused on the junction with irradiation doses ranging from 100 to 300 ions/nm and demonstrated that the junction barrier can be modulated by the ion dose and that within this dose range,the junctions behave like superconductor–normal conductor–superconductor junctions.The measurements of the I–V characteristics,Fraunhofer diffraction pattern,and Shapiro steps of the junctions clearly show AC and DC Josephson effects.Our findings demonstrate high reproducibility of junction fabrication using a focused helium ion beam and suggest that commercial devices based on this nanotechnology could operate at liquid nitrogen temperatures.
基金supported by the National Key R&D Program of China(No.2018YFB1502202)the Fundamental Research Funds for the Central Universities(No.FRF-GF-20-09B).
文摘Performance degradation shortens the life of solid oxide fuel cells in practical applications.Revealing the degradation mechanism is crucial for the continuous improvement of cell durability.In this work,the effects of cell operating conditions on the terminal voltage and anode microstructure of a Ni-yttria-stabilized zirconia anode-supported single cell were investigated.The microstructure of the anode active area near the electrolyte was characterized by laser optical microscopy and focused ion beam-scanning electron microscopy.Ni depletion at the anode/electrolyte interface region was observed after 100 h discharge tests.In addition,the long-term stability of the single cell was evaluated at 700℃for 3000 h.After an initial decline,the anode-supported single cell exhibits good durability with a voltage decay rate of 0.72%/kh and an electrode polarization resistance decay rate of 0.17%/kh.The main performance loss of the cell originates from the initial degradation.
基金supported by the National Natural Science Foundation of China (Grant No.12104016)the National Key Research and Development Program of China (Grant No.2020YFF01014706)。
文摘Half-integer microwave induced steps(Shapiro steps)have been observed in many different Josephson junction systems,which have attracted a lot of attention because they signify the deviation of current phase relation(CPR)and uncover many unconventional physical properties.In this article,we first report the discovery of half-integer Shapiro steps in MgB_(2)focused He ion beam(He-FIB)Josephson junctions.The half-integer steps'dependence on microwave frequency,temperature,microwave power,and magnetic field is also analyzed.We find that the existence of half-integer steps can be controlled by the magnetic field periodically,which is similar to that of high temperature superconductor(HTS)grain boundary junctions,and the similarity of the microstructures between gain boundary junctions and He-FIB junctions is discussed.As a consequence,we mainly attribute the physical origin of half-integer steps in MgB_(2)He-FIB junctions to the model that a He-FIB junction is analogous to a parallel junctions'array.Our results show that He-FIB technology is a promising platform for researching CPR in junctions made of different superconductors.
基金supported by the National Key R&D Program of China(Grant No.2020YFA0711802)the Strategic Program of Chinese Academy of Sciences(Grant No.XDB10030400)。
文摘The three-dimensional(3D)pore structures and permeability of shale are critical for forecasting gas production capacity and guiding pressure differential control in practical reservoir extraction.However,few investigations have analyzed the effects of microscopic organic matter(OM)morphology and 3D pore nanostructures on the stress sensitivity,which are precisely the most unique and controlling factors of reservoir quality in shales.In this study,ultra-high nanoscale-resolution imaging experiments,i.e.focused ion beam-scanning electron microscopy(FIB-SEMs),were conducted on two organic-rich shale samples from Longmaxi and Wufeng Formations in northern Guizhou Depression,China.Pore morphology,porosity of 3D pore nanostructures,pore size distribution,and connectivity of the six selected regions of interest(including clump-shaped OMs,interstitial OMs,framboidal pyrite,and microfractures)were qualitatively and quantitatively characterized.Pulse decay permeability(PDP)measurement was used to investigate the variation patterns of stress-dependent permeability and stress sensitivity of shales under different confining pressures and pore pressures,and the results were then used to calculate the Biot coefficients for the two shale formations.The results showed that the samples have high OM porosity and 85%of the OM pores have the radius of less than 40 nm.The OM morphology and pore structure characteristics of the Longmaxi and Wufeng Formations were distinctly different.In particular,the OM in the Wufeng Formation samples developed some OM pores with radius larger than500 nm,which significantly improved the connectivity.The macroscopic permeability strongly depends on the permeability of OM pores.The stress sensitivity of permeability of Wufeng Formation was significantly lower than that of Longmaxi Formation,due to the differences in OM morphology and pore structures.The Biot coefficients of 0.729 and 0.697 were obtained for the Longmaxi and Wufeng Formations,respectively.
基金supported by the National Natural Science Foundation of China(No.51222106)the Fundamental Research Funds for the Central Universities(No.FRF-TP-14-011C1)+1 种基金the Major State Basic Research Development Program of China(No.2014CB643300)the Beijing Municipal Commission of Education
文摘The influence of oxide scales on the corrosion behaviors of B510 L hot-rolled steel strips was investigated in this study. Focused ion beams and scanning electron microscopy were used to observe the morphologies of oxide scales on the surface and cross sections of the hot-rolled steel. Raman spectroscopy and X-ray diffraction were used for the phase analysis of the oxide scales and corrosion products. The corrosion potential and impedance were measured by anodic polarization and electrochemical impedance spectroscopy. According to the results, oxide scales on the hot-rolled strips mainly comprise iron and iron oxides. The correlation between mass gain and test time follows a power exponential rule in the damp-heat test. The corrosion products are found to be mainly composed of γ-Fe OOH, Fe3O4, ?-Fe OOH, and γ-Fe2O3. The contents of the corrosion products are different on the surfaces of the steels with and without oxide scales. The steel with oxide scales is found to show a higher corrosion resistance and lower corrosion rate.
基金The electrochemical part of the research done at Oak Ridge National Laboratory,managed by UT Battelle,LLC,for the U.S.Department of Energy(DOE)under contract DE-AC05-00OR22725,was sponsored by the Office of Energy Efficiency and Renewable Energy(EERE)Vehicle Technologies OfficeT.S.acknowledges the support from the EPSRC project(EP/P001521/1)“Integrated Plasma Source Focused Ion Beam with Scanning Electron Microscope.”Y.Z.acknowledges support from EPSRC project(EP/V002260/1),UK National Measurement System and ISCF Measurement Fellowship.
文摘Despite the long-established rocking-chair theory of lithium-ion batteries(LIBs),developing novel characterization methodology with higher spatiotemporal resolution facilitates a better understanding of the solid electrolyte interphase studies to shape the reaction mechanisms.In this work,we develop a Xenon ion plasma focused ion beam(Xe+PFIB)-based characterization technique to probe the cross-sectional interface of both ternary cathode and graphite anode electrodes,with the focus on revealing the chemical composition and distribution underneath the electrode surface by in-depth analysis of secondary ions.Particularly,the lithium fluoride is detected in the pristine cathode prior to contact with the electrolyte,reflecting that the electrode degradation is in the form of the loss of lithium inventory during electrode preparation.This degradation is related to the hydrolysis of the cathode material and the decomposition of the PVDF binder.Through the quantitative analysis of the transition-metal degradation products,manganese is found to be the dominant element in the newly formed inactive fluoride deposition on the cathode,while no transition metal signal can be found inside the anode electrode.These insights at high resolution implemented via a PFIB-based characterization technique not only enrich the understanding of the degradation mechanism in the LIBs but also identify and enable a high-sensitivity methodology to obtain the chemical survey at the subsurface,which will help remove the capacity-fade observed in most LIBs.
基金supported by EPSRC through grants"Multi-disciplinary Centre for In-situ Processing Studies(CIPS)"(EP/I020691),"Micromechanical Modelling and Experimentation"(EP/G004676),and "New Dimensions of Engineering Science at Large Facilities"(EP/H003215)
文摘Human dental hard tissues are dentine, cementum, and enamel. These are hydrated mineralised composite tissues with a hierarchical structure and versatile thermo-mechanical properties. The hierarchical structure of dentine and enamel was imaged by transmission electron microscopy (TEM) of samples prepared by focused ion beam (FIB) milling. High resolution TEM was carried out in the vicinity of a crack tip in dentine. An intricate "random weave" pattern of hydroxyapatile crystallites was observed and this provided a possible explanation for toughening of the mineralized dentine tissue at the nano-scale. The results reported here provide the basis for improved understanding of the rela- tionship between the multi-scale nature and the mechanical properties of hierarchically structured biomaterials, and will also be useful for the development of better prosthetic and dental restorative materials.
基金We thank the Deutsche Forschungsgemeinschaft(DFG)for financial support through the project Ro1198/22-1“Energy induced nanoparticle substrate interactions”.
文摘Focused ion beam(FIB)processing with low-energy ions has become a standard technique for the manipulation of nanostructures.Many underlying ion beam effects that deviate from conventional high-energy ion irradiation of bulk systems are considered today;however,ion channeling with its consequence of significant deeper penetration depth has been only theoretically investigated in this regime.We present here an experimental approach to determine the channeling of low-energy ions in crystalline nanoparticles by measuring the sputter yield derived from scanning electron microscopy(SEM)images taken after irradiation under various incident ion angles.Channeling maps of 30 and 20 keV Ga+ions in Ag nanocubes have been identified and fit well with the theory.Indeed,channeling has a significant impact on the transport of energetic ions in crystals due to the large critical angle at low ion energies,thus being relevant for any FIB-application.Consequently,the obtained sputter yield clearly differs from amorphous materials;therefore,it is recommended not to rely only on,e.g.,ion distribution depths predicted by standard Monte-Carlo(MC)algorithms for amorphous materials.
基金supported by National Key Research and Development Project of China(No.2022YFE0113800)National Natural Science Foundation of China(Nos.22288101,21972136,21991090 and 21991091)Key Research Program of Frontier Sciences,Chinese Academy of Sciences(No.QYZDB-SSW-JSC040)。
文摘Aluminosilicate small pore zeolites belonging to ABC-6 family play crucially important roles in the high methanol conversion with the high selectivity of light olefins,gas separation and storage,and selective catalytic reduction of NO_(x).In this work,we report a general method,called the epitaxial growth approach,for designing ABC-6 family small pore zeolites.It is mainly realized through the epitaxial growth on the nonporous SOD-type zeolite in the presence of inorganic cations(Na^(+)and K^(+))combined with a variety of organic structure directing agents(OSDAs).In this case,a series of ABC-6 family small pore zeolites such as ERI-,SWY-,LEV-,AFX-,and PTT-type zeolites have been successfully synthesized within a few hours.More importantly,the advanced focused ion beam(FIB)and the low-dose high-resolution transmission electron microscopy(HRTEM)imaging technique have been utilized for unraveling the zeolite heterojunction at the atomic level during the epitaxial growth process.It turns out(222)crystallographic planes of the SOD-type zeolite substrate provide unique pre-building units,which facilitate the growth of targeted ABC-6 family small pore zeolites along its c-axis.Moreover,the morphologies of ERI-type zeolite can also be tuned through the epitaxial growth approach,achieving a longer lifetime in the methanol conversion.
基金funded by National Basic Research Program of China(2010CB630800,2015CB921700)National Natural Science Foundation of China(51671112,51471096,51390471,11374174)+2 种基金National Key Research and Development Program(2016YFB0700402)National Key Scientific Instruments and Equipment Development Project(2013YQ120353)Tsinghua University(20141081200)
文摘The microstructural evolutions of 5Mn steel during various heat treatments have been investiga- ted by in-situ transmission electron microscopy (TEM). The specimen of 5Mn steel was pre- pared using focused ion beam (FIB) milling, which allowed the selection of specific morphology of interest prior to the in-situ observation, The complete austenization at 800 ℃ was verified at the atomic scale by minimizing thermal expansion and sample drift in a heating holder based on micro-electro-mechanical-systems. During annealing at 650 ℃, the formation of reverted austen- ite was dynamically observed, while the morphologies of austenite laths of 5Mn steel after in-situ heating were quite similar to that after ex-situ intereritical annealing. During annealing at 500 ℃, the morphological evolution of cementite and associated Mn diffusion were investigated. It was demonstrated that a combination of FIB sampling and high temperature in-situ TEM enables us to probe the morphological evolution and elemental diffusion of specific areas of interest in steel at high spatial resolution.
基金by the National Science Foundation and the Ministry of Science and Technology of China and the Penn.State MRSEC under NSF grant DMR-0820404.
文摘Pb nanobridges with a thickness of less than 10 nm and a width of several hundred nm have been fabricated from single-crystalline Pb fi lms using low-temperature molecular beam epitaxy and focus ion beam microfabrication techniques.We observed novel magnetoresistance oscillations below the superconducting transition temperature(TC)of the bridges.The oscillations which were not seen in the crystalline Pb fi lmsmay originate from the inhomogeneity of superconductivity induced by the applied magnetic fi elds on approaching the normal state,or the degradation of fi lm quality by thermal evolution.
基金The authors gratefully acknowledge the startup funding support by the Dalian University of Technology(DUT)(Award No.82232022,82232043,and DUT22LAB404)。
文摘Focused ion beam (FIB) machining can be used to fabricate gallium arsenide-based devices, which have a surface fnish of several nanometers, and the FIB machining speed and surface fnish can be greatly improved using xenon difuoride (XeF2) gas-assisted etching. Although the refresh time is one of the most important parameters in the gas-assisted etching process, its efect on the machining quality of the surface fnish has rarely been studied. Therefore, in this work, we investigated the efect of the refresh time on the etching process, including the dissociation process of XeF2, the refresh time dependency of the sputter in yield under diferent incident angles, and the surface fnish under diferent refresh times. The results revealed that a selective etching mechanism occurred at diferent refresh times. At an incidence angle of 0°, the sputtering yield increased with the refresh time and reached its maximum value at 500 ms;at an incidence angle of 30°, the sputtering yield reached its minimum value at a refresh time of 500 ms. For surface roughness, the incident angle played a more important role than the refresh time. The surface fnish was slightly better at an incidence angle of 30° than at 0°. In addition, both F and Xe elements were detected in the processed area: Xe elements were evenly distributed throughout the processing area, while F elements tended to accumulate in the whole processing area. The results suggest that the optimum surface can be obtained when a larger refresh time is employed.