Design and Grasping Force Modeling for a Soft Robotic Gripper with Multi-stem Twining

To improve the grasping power of soft robots,inspired by the scene of intertwined and interdependent vine branches safely clinging to habitats in a violent storm and the phenomenon of large grasping force after being entangled by aquatic plants,this paper proposes a soft robotic gripper with multi-stem twining.The proposed robotic gripper can realize a larger contact area of surrounding or containing object and more layers of a twining object than the current twining gripping methods.It not only retains the adaptive advantages of twining grasping but also improves the grasping force.First,based on the mechanical characteristics of the multi-stem twining of the gripper,the twining grasping model is developed.Then,the force on the fiber is deduced by using the twining theory,and the axial force of the gripper is analyzed based on the equivalent model of the rubber ring.Finally,the torsion experiments of fibers and the grasping experiments of the gripper are designed and conducted.The torsion experiment of fibers verifies the influence of a different number of fiber ropes and fiber torque on the grasping force,and the grasping experiment reflects the large load of the gripper and the high adaptability and practicability under different tasks.

Comparisons of Wave Force Model Effects on the Structural Responses and Fatigue Loads of a Semi-Submersible Floating Wind Turbine

The selection of wave force models will significantly impact the structural responses of floating wind turbines.In this study,comparisons of wave force model effects on the structural responses and fatigue loads of a semi-submersible floating wind turbine(SFWT)were conducted.Simulations were performed by employing the Morison equation(ME)with linear or second-order wave kinematics and potential flow theory(PFT)with first-or second-order wave forces.A comparison of regular waves,irregular waves,and coupled wind/waves analyses with the experimental data showed that many of the simulation results and experimental data are relatively consistent.However,notable discrepancies are found in the response amplitude operators for platform heave,tower base bending moment,and tension in mooring lines.PFT models give more satisfactory results of heave but more significant discrepan-cies in tower base bending moment than the ME models.In irregular wave analyses,low-frequency resonances were captured by PFT models with second-order difference-frequency terms,and high-frequency resonances were captured by the ME models or PFT models with second-order sum-frequency terms.These force models capture the response frequencies but do not reasonably predict the response amplitudes.The coupled wind/waves analyses showed more satisfactory results than the wave-only analyses.However,an important detail to note is that this satisfactory result is based on the overprediction of wind-induced responses.

An extended social force model on unidirectional flow considering psychological and behavioral impacts of hazard source

An accurate assessment of the evacuation efficiency in case of disasters is of vital importance to the safety design of buildings and street blocks.Hazard sources not only physically but psychologically affect the pedestrians,which may further alter their behavioral patterns.This effect is especially significant in narrow spaces,such as corridors and alleys.This study aims to integrate a non-spreading hazard source into the social force model following the results from a previous experiment and simulation,and to simulate unidirectional pedestrian flows over various crowd densities and clarity–intensity properties of the hazard source.The integration include a virtual repulsion force from the hazard source and a decay on the social force term.The simulations reveal(i)that the hazard source creates virtual bottlenecks that suppress the flow,(ii)that the inter-pedestrian push forms a stabilisation phase on the flow-density curve within medium-to-high densities,and(iii)that the pedestrians are prone to a less orderly and stable pattern of movement in low clarity–intensity scenarios,possibly with lateral collisions passing the hazard source.

MODELING, VALIDATION AND OPTIMAL DESIGN OF THE CLAMPING FORCE CONTROL VALVE USED IN CONTINUOUSLY VARIABLE TRANSMISSION

Associated dynamic performance of the clamping force control valve used in continuously variable transmission （CVT） is optimized. Firstly, the structure and working principle of the valve are analyzed, and then a dynamic model is set up by means of mechanism analysis. For the purpose of checking the validity of the modeling method, a prototype workpiece of the valve is manufactured for comparison test, and its simulation result follows the experimental result quite well. An associated performance index is founded considering the response time, overshoot and saving energy, and five structural parameters are selected to adjust for deriving the optimal associated performance index. The optimization problem is solved by the genetic algorithm （GA） with necessary constraints. Finally, the properties of the optimized valve are compared with those of the prototype workpiece, and the results prove that the dynamic performance indexes of the optimized valve are much better than those of the prototype workpiece.

Simulation based on a modified social force model for sensitivity to emergency signs in subway station

The subway is the primary travel tool for urban residents in China. Due to the complex structure of the subway and high personnel density in rush hours, subway evacuation capacity is critical. The subway evacuation model is explored in this work by combining the improved social force model with the view radius using the Vicsek model. The pedestrians are divided into two categories based on different force models. The first category is sensitive pedestrians who have normal responses to emergency signs. The second category is insensitive pedestrians. By simulating different proportions of the insensitive pedestrians, we find that the escape time is directly proportional to the number of insensitive pedestrians and inversely proportional to the view radius. However, when the view radius is large enough, the escape time does not change significantly, and the evacuation of people in a small view radius environment tends to be integrated. With the improvement of view radius conditions, the escape time changes more obviously with the proportion of insensitive pedestrians. A new emergency sign layout is proposed, and the simulations show that the proposed layout can effectively reduce the escape time in a small view radius environment. However, the evacuation effect of the new escape sign layout on the large view radius environment is not apparent. In this case, the exit setting emerges as an additional factor affecting the escape time.

Milling Force Model for Aviation Aluminum Alloy: Academic Insight and Perspective Analysis

Aluminum alloy is the main structural material of aircraft,launch vehicle,spaceship,and space station and is processed by milling.However,tool wear and vibration are the bottlenecks in the milling process of aviation aluminum alloy.The machining accuracy and surface quality of aluminum alloy milling depend on the cutting parameters,material mechanical properties,machine tools,and other parameters.In particular,milling force is the crucial factor to determine material removal and workpiece surface integrity.However,establishing the prediction model of milling force is important and difficult because milling force is the result of multiparameter coupling of process system.The research progress of cutting force model is reviewed from three modeling methods:empirical model,finite element simulation,and instantaneous milling force model.The problems of cutting force modeling are also determined.In view of these problems,the future work direction is proposed in the following four aspects:(1)high-speed milling is adopted for the thin-walled structure of large aviation with large cutting depth,which easily produces high residual stress.The residual stress should be analyzed under this particular condition.(2)Multiple factors(e.g.,eccentric swing milling parameters,lubrication conditions,tools,tool and workpiece deformation,and size effect)should be considered comprehensively when modeling instantaneous milling forces,especially for micro milling and complex surface machining.(3)The database of milling force model,including the corresponding workpiece materials,working condition,cutting tools(geometric figures and coatings),and other parameters,should be established.(4)The effect of chatter on the prediction accuracy of milling force cannot be ignored in thin-walled workpiece milling.(5)The cutting force of aviation aluminum alloy milling under the condition of minimum quantity lubrication(mql)and nanofluid mql should be predicted.

Study on Model Tests and Hydrodynamic Force Models for Free Spanning Submarine Pipelines Subjected to Earthquakes

A test rig is built to model the dynamic response of submarine pipelines with an underwater shaking table in the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, China. Model tests are carried out to consider the effects of exciting wave directions and types. Based on the experimental results, two hydrodynamic force models derived from Morisen equation and Wake model are presented respectively. By use of hydrodynamic force models suitable for free spanning submarine pipelines under earthquakes, diseretized equations of motion are obtained and finite element models are established to analyze dynamic response of free spanning submarine pipeline subjected to multi-support seismic excitations. The comparison of numerical results with experimental results shows that the improved Morison and Wake hydrodynamic force models could satisfactorily predict dynamic response on the free spanning submarine pipelines subjected to earthquakes.

Application of a new wind driving force model in soil wind erosion area of northern China

The shear stress generated by the wind on the land surface is the driving force that results in the wind erosion of the soil.It is an independent factor influencing soil wind erosion.The factors related to wind erosivity,known as submodels,mainly include the weather factor(WF)in revised wind erosion equation(RWEQ),the erosion submodel(ES)in wind erosion prediction system(WEPS),as well as the drift potential(DP)in wind energy environmental assessment.However,the essential factors of WF and ES contain wind,soil characteristics and surface coverings,which therefore results in the interdependence between WF or ES and other factors(e.g.,soil erodible factor)in soil erosion models.Considering that DP is a relative indicator of the wind energy environment and does not have the value of expressing wind to induce shear stress on the surface.Therefore,a new factor is needed to express accurately wind erosivity.Based on the theoretical basis that the soil loss by wind erosion(Q)is proportional to the shear stress of the wind on the soil surface,a new model of wind driving force(WDF)was established,which expresses the potential capacity of wind to drive soil mass in per unit area and a period of time.Through the calculations in the typical area,the WDF,WF and DP are compared and analyzed from the theoretical basis,construction goal,problem-solving ability and typical area application;the spatial distribution of soil wind erosion intensity was concurrently compared with the spatial distributions of the WDF,WF and DP values in the typical area.The results indicate that the WDF is better to reflect the potential capacity of wind erosivity than WF and DP,and that the WDF model is a good model with universal applicability and can be logically incorporated into the soil wind erosion models.

An Experimental Study of Several Special Issues Regarding the Ice Force on Conical Structures

The effect of the cone spacing of a conieal structure on the ice force is studied by model experiments. The ice force reduction coefficient presented in this paper expresses the relationship between the ice force and the arrangement of cones. The experiments prove that the mode of the ice failure before the boundary of upward-downward bending cone (UDBC) is crushing. A conclusion can also be drawn from the experiments that the ice force on the boundary of UDBC is by far less than that on a vertical pile with the same diameter. Moreover, the ice force frequencies on upright and inve-rted cones are obtained under the field condition of the platform JZ20-2, respectively. The results show that the alterna-tion of the ice force on UDBC can hardly induce resonance of platform JZ20-2.

Assessment of force models on finite-sized particles at finite Reynolds numbers

Finite-sized inertial spherical particles are fully-resolved with the immersed boundary projection method(IBPM)in the turbulent open-channel flow by direct numerical simulation(DNS).The accuracy of the particle surface force models is investigated in comparison with the total force obtained via the fully-resolved method.The results show that the steady-state resistance only performs well in the streamwise direction,while the fluid acceleration force,the added-mass force,and the shear-induced Saffman lift can effectively compensate for the large-amplitude and high-frequency characteristics of the particle surface forces,especially for the wall-normal and spanwise components.The modified steady-state resistance with the correction effects of the acceleration and the fluid shear can better represent the overall forces imposed on the particles,and it is a preferable choice of the surface force model in the Lagrangian point-particle method.

The Shielding Effect of Multi-Pile Structures on Ice Force

The shielding effect of the front pile-row on the ice force acting on the back pile-row is studied by ice force model tests. In the tests, the front pile-row is designed to model jacket legs and the back pile-row to model the water resisting pipe-phalanx within the jacket. The shielding factor for ice force corresponding to different conditions are given in this paper. The research indicates that there are many factors, including the longitudinal and lateral spacing between the front and back pile-row, ice attacking angle and the ratio of pile diameter to ice thickness, that influence the shielding effect on ice force.

Composite Adaptive Control of Belt Polishing Force for Aero-engine Blade

The existing methods for blade polishing mainly focus on robot polishing and manual grinding.Due to the difficulty in high-precision control of the polishing force,the blade surface precision is very low in robot polishing,in particular,quality of the inlet and exhaust edges can not satisfy the processing requirements.Manual grinding has low efficiency,high labor intensity and unstable processing quality,moreover,the polished surface is vulnerable to burn,and the surface precision and integrity are difficult to ensure.In order to further improve the profile accuracy and surface quality,a pneumatic flexible polishing force-exerting mechanism is designed and a dual-mode switching composite adaptive control(DSCAC) strategy is proposed,which combines Bang-Bang control and model reference adaptive control based on fuzzy neural network(MRACFNN) together.By the mode decision-making mechanism,Bang-Bang control is used to track the control command signal quickly when the actual polishing force is far away from the target value,and MRACFNN is utilized in smaller error ranges to improve the system robustness and control precision.Based on the mathematical model of the force-exerting mechanism,simulation analysis is implemented on DSCAC.Simulation results show that the output polishing force can better track the given signal.Finally,the blade polishing experiments are carried out on the designed polishing equipment.Experimental results show that DSCAC can effectively mitigate the influence of gas compressibility,valve dead-time effect,valve nonlinear flow,cylinder friction,measurement noise and other interference on the control precision of polishing force,which has high control precision,strong robustness,strong anti-interference ability and other advantages compared with MRACFNN.The proposed research achieves high-precision control of the polishing force,effectively improves the blade machining precision and surface consistency,and significantly reduces the surface roughness.

Simulation of Crowd Motion Based on Boids Flocking Behavior and Social Force Model

In the process of crowd movement,pedestrians are often affected by their neighbors.In order to describe the consistency of adjacent individuals and collectivity of a group,this paper learns from the rules of the flocking behavior,such as segregation,alignment and cohesion,and proposes a method for crowd motion simulation based on the Boids model and social force model.Firstly,the perception area of individuals is divided into zone of segregation,alignment and cohesion.Secondly,the interactive force among individuals is calculated based upon the zone information,velocity vector and the group information.The interactive force among individuals is the synthesis of three forces:the repulsion force to avoid collisions,the alignment force to keep consistent with the velocity direction,and the attractive force to get close to the members of group.In segregation and alignment areas,the repulsion force and alignment force among pedestrians are limited by visual field factors.Finally,the interactive force among individuals,the driving force of destination and the repulsion force of obstacles work together to drive the behavior of crowd motion.The simulation results show that the proposed method can not only effectively simulate the interactive behavior between adjacent individuals but also the collective behavior of group.

Study on High-Performance Computing for Simulation of End Milling Force

Milling Process Simulation is one of the important re search areas in manufacturing science. For the purpose of improving the prec ision of simulation and extending its usability, numerical algorithm is more and more used in the milling modeling areas. But simulative efficiency is decreasin g with increase of its complexity. As a result, application of the method is lim ited. Aimed at above question, high-efficient algorithm for milling process sim ulation is studied. It is important for milling process simulation’s applicatio n. Parallel computing is widely used to solve the large-scale computation question s. Its advantages include system flexibility, robust, high-efficient computing capability and high ratio of performance to price. With the development of compu ter network, utilizing the computing resource in the Internet, a virtual computi ng environment with powerful computing capability can be consisted by microc omputers, and the difficulty of building hardware environment which is used to s upport parallel computing is reduced. How to use network technology and parallel algorithm to improve simulative effic iency for milling forces simulation is investigated in the paper. In order to pr edict milling forces, a simplified local milling forces model is used in the pap er. End milling cutter is assumed to be divided by r number of differential elem ents along the axial direction of the cutter. For a given time, the total cuttin g forces can be obtained by summarizing the resultant cutting force produced by each differential cutter disc. Divide the whole simulative time into some segmen ts, send these program’s segments to microcomputers in the Internet and obtain the result of the program’s segments, all of the result of program’s segments a re composed the final result. For implementing the algorithm, a distributed Parallel computing framework is de signed in the paper. In the framework, web server plays a role of controller. Us ing Java RMI(remote method interface), the computing processes in computing serv er are called by web server. There are lots of control processes in web server a nd control the computing servers. The codes of simulative algorithm can be dynam ic sent to the computing servers, and milling forces at the different time are c omputed through utilizing the local computer’s resource. The results that are ca lculated by every computing servers are sent to the web server, and composed the final result. The framework can be used by different simulative algorithm. Comp ared with the algorithm running single machine, the efficiency of provided algor ithm is higher than that of single machine.

Mesh Force Modelling and Parametric Studies for Compound Oscillatory Roller Reducer

A compound oscillatory roller reducer(CORR)with a first-stage gear transmission and a second-stage oscillatory roller transmission is presented.The transmission principle of oscillatory roller transmission is introduced,and the tooth profile equation of the inner gear is derived.The analytical model of mesh force considering the installation errors and manufacturing errors is proposed.Then,parametric studies considering different errors on the mesh force are conducted.Results show that the design parameters are significant factors for mesh force.The mesh force is reduced by 17%as the eccentricity of disk cam increases from 2.5 mm to 4 mm.When the radius of the movable roller increases from 7 mm to 20 mm,the mesh force decreases by 8%.As the radius of disk cam increases from 125 mm to 170 mm,the mesh force is decreased by 26.5%.For the impacts of errors,the mesh force has a noticeable fluctuation when these errors exist including the manufacturing error of disk cam,the installation error of disk cam and the manufacturing error of movable roller change.The prototype of the reducer is manufactured and preliminary run-in test proved the feasibility of the transmission principle.

Constant evacuation time gap: Experimental study and modeling

In this paper, the evacuation dynamics in an artificial room with only one exit is investigated via experiments and modeling. Two sets of experiments are implemented, in which pedestrians are asked to escape individually. It is found that the average evacuation time gap is essentially constant. To model the evacuation dynamics, an improved social force model is proposed, in which it is assumed that the driving force of a pedestrian cannot be performed when the resultant physical force exceeds a threshold. Simulation results are in good agreement with the experimental ones.

FORCE FEEDBACK MODEL OF ELECTRO-HYDRAULIC SERVO TELE-OPERATION ROBOT BASED ON VELOCITY CONTROL

The tele-operation robotic system which consists of an excavator as the construction robot, and two joysticks for operating the robot from a safe place are useful for performing restoration in damaged areas. In order to accomplish a precise task, the operator needs to feel a realistic sense of task force brought about from a feedback force between the fork glove of slave robot and unfamiliar environment. A novel force feedback model is proposed based on velocity control of cylinder to determine environment force acting on fork glove. Namely, the feedback force is formed by the error of displacement of joystick with velocity and driving force of piston, and the gain is calculated by the driving force and threshold of driving force of hydraulic cylinder. Moreover, the variable gain improved algorithm is developed to overcome the defect for grasping soft object. Experimental results for fork glove freedom of robotic system are provided to demonstrate the developed algorithm is available for grasping soft object.

Dynamic Modeling of Variable Stiffness and Damping for Spatial Linkage Weft Insertion Mechanism with Clearance

In order to further analyze the influence of clearance on the kinematic performance of spatial linkage weft insertion mechanism,it is necessary to study the dynamic characteristics of contact impact force model with the variable stiffness and damping coefficient.Firstly,the parameters in the output process of the system are solved by describing of the flexible joint clearance.Then,based on Lankarani-Nikravesh contact force model,the contact impact stiffness and damping coefficient is modified from fixed values to time-varying coefficients.The dynamic model of spatial linkage weft insertion mechanism with modified clearance is established by Lagrange method,and the dynamic characteristics of the system are calculated.The results show that the joint clearance can directly affect the output performance of the mechanism.With the increase of the clearance value,the curve fluctuations of acceleration,driving torque and collision force are obvious,and it will be further intensified with the increase of spindle speed,which greatly affects the stability of mechanism and fabric quality.Finally,the virtual prototype is established by the SolidWorks software and simulated by the ADAMS software.The simulation results are compared with the numerical results,which verifies the accuracy of the modeling method in this paper.

Stability of rat models of fluid percussion-induced traumatic brain injury: comparison of three different impact forces

Fluid percussion-induced traumatic brain injury models have been widely used in experimental research for years. In an experiment, the stability of impaction is inevitably affected by factors such as the appearance of liquid spikes. Management of impact pressure is a crucial factor that determines the stability of these models, and direction of impact control is another basic element. To improve experimental stability, we calculated a pressure curve by generating repeated impacts using a fluid percussion device at different pendulum angles. A stereotactic frame was used to control the direction of impact. We produced stable and reproducible models, including mild, moderate, and severe traumatic brain injury, using the MODEL01-B device at pendulum angles of 6°, 11° and 13°, with corresponding impact force values of 1.0 ± 0.11 atm（101.32 ± 11.16 k Pa）, 2.6 ± 0.16 atm（263.44 ± 16.21 k Pa）, and 3.6 ± 0.16 atm（364.77 ± 16.21 k Pa）, respectively. Behavioral tests, hematoxylin-eosin staining, and magnetic resonance imaging revealed that models for different degrees of injury were consistent with the clinical properties of mild, moderate, and severe craniocerebral injuries. Using this method, we established fluid percussion models for different degrees of injury and stabilized pathological features based on precise power and direction control.

Model of Aluminium Foil Rolling Force Based on Neural Networks

Based on the principle of BP neural networks, the rolling force model is established after thoroughly analyzing and reprocessing the data of 1 350 mm aluminium foil mill. It states that the difference between the output of artificial neural networks rolling force model and the real value is in the order of 3 percent. The model reflects the real feature of process.