Analysis and synchronization controller design of dual-port gridforming voltage-source converters for different operation modes

Grid-tie voltage source converters(VSCs)can operate in three distinct modes:AC-dominant,DC-dominant,and balanced,depending on the placement of the stiff voltage sources.The distinct operation modes of the VSCs traditionally demand different synchronization control techniques,leading to heterogeneous VSCs.It is challenging for the power system to accommodate and coordinate heterogeneous VSCs.A promising universal synchronization control technique for VSCs is the DC-link voltage synchronization control(DVSC)based on a lead compensator(LC).The LC DVSC stabilizes both the DC and AC voltages of a VSC while achieving synchronization with the AC grid.This results in a dual-port grid-forming(DGFM)characteristic for the VSC.However,there has been very limited study on the stability and synchronization controller design of the VSCs with the LC DVSC operating in various modes.To bridge this gap,the paper presents a quantitative analysis on the stability and steady-state performance of the LC DVSC in all three operation modes of the DGFM VSC.Based on the analysis,the paper provides step-by-step design guidelines for the LC DVSC.Furthermore,the paper uncovers an instability issue related to the LC DVSC when the DGFM VSC operates in the balanced mode.To tackle the instability issue,a virtual resistance control is proposed and integrated with the LC DVSC.Simulation results validate the analysis and demonstrate the effectiveness of the DGFM VSC with the LC DVSC designed using the proposed guidelines in all three operation modes.Overall,the paper demonstrates the feasibility of employing the DGFM VSC with the LC DVSC for all three possible operation modes,which can help overcome the challenges associated with accommodating and coordinating heterogeneous VSCs in the power system.

Microstructure and forming mechanism of metals subjected to ultrasonic vibration plastic forming: A mini review

Compared with traditional plastic forming,ultrasonic vibration plastic forming has the advantages of reducing the forming force and improving the surface quality of the workpiece.This technology has a very broad application prospect in industrial manufactur-ing.Researchers have conducted extensive research on the ultrasonic vibration plastic forming of metals and laid a deep foundation for the development of this field.In this review,metals were classified according to their crystal structures.The effects of ultrasonic vibration on the microstructure of face-centered cubic,body-centered cubic,and hexagonal close-packed metals during plastic forming and the mech-anism underlying ultrasonic vibration forming were reviewed.The main challenges and future research direction of the ultrasonic vibra-tion plastic forming of metals were also discussed.

An overview of grid-forming technology and its application in new-type power system

To address the global climate crisis,achieving energy transitions is imperative.Establishing a new-type power system is a key measure to achieve CO_(2) emissions peaking and carbon neutrality.The core goal is to transform renewable energy resources into primary power sources.The large-scale integration of high proportions of renewable energy sources and power electronic devices will dramatically change the operational mechanisms and control strategies of power systems.Existing wind and solar converters mostly adopt the grid-following control mode,which leads to significant challenges in system security and stability as it is insufficient to support the frequency and voltage of the grid.On the other hand,grid-forming control technology(GFM)can provide voltage and frequency support for the system,and thus becomes an effective measure to improve the inertia and damping characteristics of power systems.This paper illustrates the principles,control strategies,equipment types,application scenarios,and project implementation of grid-forming technology.The simulation and analysis based on a renewable-dominated real new-type power system show that GFM can significantly enhance the frequency and voltage support capacity of the power system,improve renewable energy accommodation capacity and grid transmission capacity under weak grid conditions,and play an important role in enhancing the stability and power supply reliability of renewable-dominated new-type power systems.

MPI/OpenMP-Based Parallel Solver for Imprint Forming Simulation

In this research,we present the pure open multi-processing(OpenMP),pure message passing interface(MPI),and hybrid MPI/OpenMP parallel solvers within the dynamic explicit central difference algorithm for the coining process to address the challenge of capturing fine relief features of approximately 50 microns.Achieving such precision demands the utilization of at least 7 million tetrahedron elements,surpassing the capabilities of traditional serial programs previously developed.To mitigate data races when calculating internal forces,intermediate arrays are introduced within the OpenMP directive.This helps ensure proper synchronization and avoid conflicts during parallel execution.Additionally,in the MPI implementation,the coins are partitioned into the desired number of regions.This division allows for efficient distribution of computational tasks across multiple processes.Numerical simulation examples are conducted to compare the three solvers with serial programs,evaluating correctness,acceleration ratio,and parallel efficiency.The results reveal a relative error of approximately 0.3%in forming force among the parallel and serial solvers,while the predicted insufficient material zones align with experimental observations.Additionally,speedup ratio and parallel efficiency are assessed for the coining process simulation.The pureMPI parallel solver achieves a maximum acceleration of 9.5 on a single computer(utilizing 12 cores)and the hybrid solver exhibits a speedup ratio of 136 in a cluster(using 6 compute nodes and 12 cores per compute node),showing the strong scalability of the hybrid MPI/OpenMP programming model.This approach effectively meets the simulation requirements for commemorative coins with intricate relief patterns.

Analysis and Optimization of the Electrohydraulic Forming Process of Sinusoidal Corrugation Tubes

Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic forming process.In the present study,the influence of the related parameters on the forming quality of a 6063 aluminum alloy sinusoidal corrugation tube has been assessed.In particular,the orthogonal experimental design(OED)and central composite design(CCD)methods have been used.Through the range analysis and variance analysis of the experimental data,the influence degree of wire diameter(WD)and discharge energy(DE)on the forming quality was determined.Multiple regression analysis was performed using the response surface methodology.A prediction model for the attaching-die state coefficient was established accordingly.The following optimal arrangement of parameters was obtained(WD=0.759 mm,DE=2.926 kJ).The attaching-die state coefficient reached the peak value of 0.001.Better optimized wire diameter and discharge energy for a better attaching-die state could be screened by CCD compared with OED.The response surface method in CCD was more suitable for the design and optimization of the considered process parameters.

Forming and Springback Prediction of Strips Under Multi-square Punch Concave Forming Process Considering Partial-unloading Effects

To further investigate the forming mechanism and springback characteristics of strips under multi-square punch forming (MSPF) considering partial-unloading effects, a series of concave form ing tests of strips are conducted on the MSPF machine. This paper aims to reveal the physical mecha nism of the elastic-plastic deformation in the MSPF process considering the effect of the forming ap proaches, and derive appropriate mathematical interpretations. The theoretical model is firstly estab lished to analyse the concave forming mechanism and springback characteristics of the strip, and its accuracy is then validated by experimental data. The forming history and load evolutions are depicted to explore the required forming capacity through the proposed analytical method. Besides, the paramet ric studies are carried out to discuss their effects on the springback of the strip. The results suggest that the deformation paths of the strip are influenced by the forming approach, and the springback of the strip in convex forming is larger than that in concave forming.

Experimental study on the forming characteristics of 1.5 GPa ultrahigh-strength dual-phase steel

The DP1500 steel series successfully produced by Baosteel is a marked improvement over the cold-rolled hot-dip galvanized dual-phase steel series.Sufficient parameter data related to forming characteristics are needed for the successful application of dual-phase steel series in engineering structures.Therefore,differences in the mech-anical properties,forming limit,hole expansion ratio,and stretch bend limit of the 1.5 GPa ultrahigh-strength steel,including DP1500,QP1500,and MS1500,have been systematically studied.Results show that the DP1500 exhibits good plastic deformation performance and approximately 5% uniform elongation,and its true major strain minimum on the forming limit curve(FLC_(0)) value is approximately 0.083,which is higher and lower than the FLC_(0) values of MS1500 and QP1500 of the same strength grade,respectively.DP1500 also exhibits good flanging and pore expansion capabilities and superior performance to QP1500 and MS1500.The minimum radius-to-thickness(R/T) ratio(1.4) of DP1500 in the 90° bend tests transverse to the rolling direction is between the R/T ratios of MS1500 and the QP1500.Overall,the formability performance of DP1500 is between that of MS1500 and QP1500.Its excellent crash energy absorption and formability performance render it a suitable structural component,and it has been successfully tested and verified on a typical complex ultrahigh-strength steel skeleton structure.

Method of fabricating artificial rock specimens based on extrusion free forming(EFF)3D printing

Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natural rock.Extrusion free forming(EFF)is a 3D printing technique that uses clay as the printing material and cures the specimens through high-temperature sintering.In this study,we attempted to use the EFF technology to fabricate artificial rock specimens.The results show the physico-mechanical properties of the specimens are significantly affected by the sintering temperature,while the nozzle diameter and layer thickness also have a certain impact.The specimens are primarily composed of SiO_(2),with mineral compositions similar to that of natural rocks.The density,uniaxial compressive strength(UCS),elastic modulus,and tensile strength of the printed specimens fall in the range of 1.65–2.54 g/cm3,16.46–50.49 MPa,2.17–13.35 GPa,and 0.82–17.18 MPa,respectively.It is capable of simulating different types of rocks,especially mudstone,sandstone,limestone,and gneiss.However,the simulation of hard rocks with UCS exceeding 50 MPa still requires validation.

Effect of Low pH on Forming Process of Desulfurization Gypsum Composite Boards Strengthened by Melamine-formaldehyde Resin

Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.

A Hybrid Optimization Approach of Single Point Incremental Sheet Forming of AISI 316L Stainless Steel Using Grey Relation Analysis Coupled with Principal Component Analysiss

We investigated the parametric optimization on incremental sheet forming of stainless steel using Grey Relational Analysis(GRA) coupled with Principal Component Analysis(PCA). AISI 316L stainless steel sheets were used to develop double wall angle pyramid with aid of tungsten carbide tool. GRA coupled with PCA was used to plan the experiment conditions. Control factors such as Tool Diameter(TD), Step Depth(SD), Bottom Wall Angle(BWA), Feed Rate(FR) and Spindle Speed(SS) on Top Wall Angle(TWA) and Top Wall Angle Surface Roughness(TWASR) have been studied. Wall angle increases with increasing tool diameter due to large contact area between tool and workpiece. As the step depth, feed rate and spindle speed increase,TWASR decreases with increasing tool diameter. As the step depth increasing, the hydrostatic stress is raised causing severe cracks in the deformed surface. Hence it was concluded that the proposed hybrid method was suitable for optimizing the factors and response.

Study of microstructure evolution of magnesium alloy cylindrical part with longitudinal inner ribs during hot flow forming by coupling ANN-modified CA and FEA

Hot flow forming(HFF)is a promising forming technology to manufacture thin-walled cylindrical part with longitudinal inner ribs(CPLIRs)made of magnesium(Mg)alloys,which has wide applications in the aerospace field.However,due to the thermo-mechanical coupling effect and the existence of stiffened structure,complex microstructure evolution and uneven microstructure occur easily at the cylindrical wall(CW)and inner rib(IR)of Mg alloy thin-walled CPLIRs during the HFF.In this paper,a modified cellular automaton(CA)model of Mg alloy considering the effects of deformation conditions on material parameters was developed using the artificial neural network(ANN)method.It is found that the ANN-modified CA model exhibits better predictability for the microstructure of hot deformation than the conventional CA model.Furthermore,the microstructure evolution of ZK61 alloy CPLIRs during the HFF was analyzed by coupling the modified CA model and finite element analysis(FEA).The results show that compared with the microstructure at the same layer of the IR,more refined grains and less sufficient DRX resulted from larger strain and strain rate occur at that of the CW;various differences of strain and strain rate in the wall-thickness exist between the CW and IR,which leads to the inhomogeneity of microstructure rising firstly and declining from the inside layer to outside layer;the obtained Hall-Petch relationship between the measured microhardness and predicted grain sizes at the CW and the IR indicates the reliability of the coupled FEA-CA simulation results.

计及构网稳定性的GFM变流器负序电流控制

构网型(GFM)变流器可在并/离网两种不同工况下实现单模式运行控制,在电网弱连接和微电网领域具有良好应用前景。这里在简要阐述GFM变流器基本模型和工作原理的基础上,分析并指出了在电网不对称条件下,常规正负序分离控制应用到GFM变流器的局限性。在此基础上,提出了一种基于谐振滤波的GFM变流器负序电流抑制策略,在电网不对称工况下实现了入网电流输出平衡,同时保证了GFM变流器在独立构网运行时的系统稳定性,仿真和实验结果验证了所提系统控制策略的正确性和有效性。

What If the Protection against Oxidation of Chromia-Forming Alloys Was Not Always Due to the Chromia Layer?

Chromia-forming alloys have good resistance to oxidizing agents such as O2, CO2, … It is accepted that the protection of these alloys is always due to the chromia layer formed at the surface of the alloys, which acts as a barrier between the oxidizing gases and the alloy substrates, forming a diffusion zone that limits the overall reaction rate and leads to parabolic kinetics. But this was not verified in the study devoted to Inconel®625 the oxidation in CO2 that was followed by TGA, with characterizations by XRD, EDS and FIB microscopy. Contrary to what was expected and accepted in similar studies on other chromia-forming alloys, it was shown that the diffusion step that governs the overall reaction rate is not located inside the chromia layer but inside the alloy, precisely inside a zone just beneath the interface alloy/chromia, this zone being depleted in chromium. The chromia layer, therefore, plays no kinetic role and does not directly protect the underlying alloy. This result was demonstrated using a simple test that consisted in removing the chromia layer from the surface of samples partially oxidized and then to continue the thermal treatment: insofar as the kinetics continued without any change in rate, this proved that this surface layer of oxide did not protect the substrate. Based on previous work on many chromia-forming alloys, the possibility of a similar reaction mechanism is discussed. If the chromia layer is not the source of protection for a number of chromia-forming alloys, as is suspected, this might have major consequences in terms of industrial applications.

基于刚塑性有限元的GFM精锻锻透性仿真

采用商用软件DEFORM用刚塑性有限元理论对GFM精锻锻透性进行了仿真研究,确认了GFM锻不透的问题并指出锻透性最大只能达到约60％,且与摩擦条件的影响关系不大,进而得出了GFM锻透性FPE与压下率△h／R的5次方回归关系式,为GFM精锻的工艺设计提供了参考。

转人工合成GFM CryIA基因烟草表现明显杀虫活性

为了使来自原核生物的苏云金芽孢杆菌（ＢａｃｉｌｕｓｔｈｕｒｉｎｇｉｅｎｓｉｓＢｅｒｌｉｎｅｒ，Ｂｔ）的杀虫晶体蛋白（ＩＣＰ）基因能够在高等植物中得到很好的表达，对编码这种杀虫晶体蛋白基因的核苷酸顺序进行了必要而又合理的修饰和改造：不改变杀虫晶体蛋白基因的氨基酸编码顺序，将杀虫晶体蛋白基因的密码子更换成植物基因组中常用的优化密码子，同时更换掉Ｂｔ杀虫晶体蛋白结构基因中的不稳定元件，人工全合成了长度为１８２４ｂｐ的杀虫晶体蛋白基因———ＧＦＭＣｒｙＩＡ基因。为了检测合成的ＧＦＭＣｒｙＩＡ基因的生物杀虫活性，将ＧＦＭＣｒｙＩＡ基因导入了烟草（ＮｉｃｏｔｉａｎａｔａｂａｃｕｍＬ．），经Ｓｏｕｔｈｅｒｎ杂交证实了ＧＦＭＣｒｙＩＡ基因已整合到转基因烟草植株的基因组中。用再生的转ＧＦＭＣｒｙＩＡ基因烟草植株的叶片喂养二龄棉铃虫（ＨｅｌｉｏｔｈｉｓａｒｍｉｇｅｒａＨüｂｎｅｒ），进行杀虫活性检测，结果表明，转ＧＦＭＣｒｙＩＡ基因烟草植株能显著地抑制棉铃虫的生长发育，表现出有效的杀虫活性。与此相反，对照植物即未转ＧＦＭＣｒｙＩＡ基因烟草植株受到棉铃虫的严重危害。这一实验结果证明：人工合成的ＧＦＭＣｒｙＩＡ基因在烟草植株中获得?

骨形成肽1和聚多巴胺复合涂层修饰提高聚醚醚酮表面活性

背景:聚醚醚酮具有与人体皮质骨相近的弹性模量及良好的射线透射性、化学稳定性和生物相容性等优点,有望应用于口腔种植领域,然而其具有生物惰性,难以与周围组织形成骨结合,因此如何提高聚醚醚酮的表面活性是目前的主要问题。目的:分析聚醚醚酮表面骨形成肽1和聚多巴胺复合涂层的促成骨和成血管作用。方法:将聚醚醚酮片浸泡于多巴胺溶液中24 h,制备聚醚醚酮-聚多巴胺材料;将聚醚醚酮-聚多巴胺材料浸泡于骨形成肽1溶液中24 h,制备聚醚醚酮-聚多巴胺-骨形成肽1材料,表征材料的微观形貌、亲水性与元素组成。将骨髓间充质干细胞分别接种于聚醚醚酮、聚醚醚酮-聚多巴胺、聚醚醚酮-聚多巴胺-骨形成肽1材料表面,通过活死细胞染色和细胞骨架染色评估细胞活性与黏附状态,茜素红和骨钙素免疫荧光染色检测细胞成骨分化能力。将人脐静脉内皮细胞分别接种于3组材料表面,通过活死细胞染色和细胞骨架/血管内皮生长因子免疫荧光染色评估细胞活性及成血管水平。结果与结论:①扫描电镜下可见聚醚醚酮材料表面光滑,聚醚醚酮-聚多巴胺材料表面出现凹凸不平的沉积物,聚醚醚酮-聚多巴胺-骨形成肽1材料表面有小颗粒突起;接触角测试结果显示,聚醚醚酮-聚多巴胺-骨形成肽1材料的亲水性优于其他两种材料;X射线光电子能谱测试结果显示,骨形成肽1成功修饰于聚醚醚酮材料表面;②活死细胞染色和细胞骨架染色显示,相较于其他两种材料,聚醚醚酮-聚多巴胺-骨形成肽1材料可提高骨髓间充质干细胞的活性与黏附;茜素红和骨钙素免疫荧光染色显示,相较于其他两种材料,聚醚醚酮-聚多巴胺-骨形成肽1材料可促进骨髓间充质干细胞的成骨分化;③活死细胞染色和免疫荧光染色显示,相较于其他两种材料,聚醚醚酮-聚多巴胺-骨形成肽1材料可提高人脐静脉内皮细胞的活性与黏附及血管内皮生长因子蛋白的表达;④结果表明,骨形成肽1和聚多巴胺复合涂层可提高聚醚醚酮表面的促成骨和成血管活性。

Forming limit of textured AZ31B magnesium alloy sheet at different temperatures

Repeated unidirectional bending （RUB） was carried out to improve the texture of commercial AZ31B magnesium alloy sheets. All specimens were prepared in the rolling direction. The forming limit diagrams （FLDs） of AZ31B magnesium alloy sheet were determined experimentally by conducting stretch-forming tests at room temperature, 100, 200 and 300 ℃ Compared with the as-received sheet, the lowest limited strain of AZ31B magnesium alloy sheet with tilted texture in the FLD increased by 79% at room temperature and 104% at 100 ℃. The texture also affected the extension of the forming limit curves （FLC） in the FLD. However, the FLCs of two kinds of sheets almost overlapped at temperature above 200 ℃. It can be concluded that the reduction of （0002） texture intensity is effective to the improvement of formability not only at room temperature but also at low-and-medium temperature. The effect of texture on FLDs becomes weak with increasing temperature.

Theoretical prediction of forming limit diagram of AZ31 magnesium alloy sheet at warm temperatures

A theoretical prediction on forming limit diagram（FLD） of AZ31 magnesium alloy sheet was developed at warm temperatures based on the M-K theory. Two different yield criteria of von Mises and Hill＇48 were applied in this model. Mechanical properties of AZ31 magnesium alloy used in the prediction were obtained by uniaxial tensile tests and the Fields-Backofen equation was incorporated in the analysis. In addition, experimental FLDs of AZ31 were acquired by conducting rigid die swell test at different temperatures to verify the prediction. It is demonstrated from a comparison between the predicted and the experimental FLDs at 473 K and 523 K that the predicted results are influenced by the type of yield criterion used in the calculation, especially at lower temperatures. Furthermore, a better agreement between the predicted results and experimental data for AZ31 magnesium alloy sheet at warm temperatures was obtained when Hill＇48 yield criterion was applied.

Influence of forming process on three-dimensional morphology of TiB_2 particles in Al-Ti-B alloys

A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.

Forming defects in aluminum alloy hot stamping of side-door impact beam

The forming defects, including thinning, rupture, wrinkling and springback, usually arising in producing a side-door impact beam, were investigated by trial and numerical simulation. A temperature-related constitutive model specific to the temperature range from 350 °C to 500 °C was established and used for the numerical simulation. The trial and numerical simulation were conducted to clarify the quantitative characteristics of forming defects and to analyze the effects of process parameters on the forming defects. Results show that the rupture situation is ameliorated and the springback is eliminated in the aluminum alloy hot stamping. The wrinkling severity decreases with increasing blank holder force (BHF), but the BHF greater than 15 kN causes the rupture at the deepest drawing position of workpiece. The forming defects are avoided with lubricant in the feasible ranges of process parameters: the BHF of 3 to 5 kN and the stamping speed of 50 to 200 mm/s.