OptoGPT: A foundation model for inverse design in optical multilayer thin film structures

Optical multilayer thin film structures have been widely used in numerous photonic applications.However,existing inverse design methods have many drawbacks because they either fail to quickly adapt to different design targets,or are difficult to suit for different types of structures,e.g.,designing for different materials at each layer.These methods also cannot accommodate versatile design situations under different angles and polarizations.In addition,how to benefit practical fabrications and manufacturing has not been extensively considered yet.In this work,we introduce OptoGPT(Opto Generative Pretrained Transformer),a decoder-only transformer,to solve all these drawbacks and issues simultaneously.

Optimal design for rubber concrete layered periodic foundations based on the analytical approximations of band gaps and mapping relations

The seismic performance of rubber concrete-layered periodic foundations are significantly influenced by their design,in which the band gaps play a paramount role.Aiming at providing better designs for these foundations,this study first proposes and validates the analytical formulas to approximate the bounds of the first few band gaps.In addition,the mapping relations linking the frequencies of different band gaps are presented.Furthermore,an optimal design method for these foundations is developed,which is validated through an engineering example.It is demonstrated that ensuring the superstructure’s resonance zones are completely covered by the corresponding periodic foundation’s band gaps can achieve satisfactory vibration attenuation effects,which is a good strategy for the design of rubber concrete layered periodic foundations.

Experimental study on seismic reinforcement of bridge foundation on silty clay landslide with inclined interlayer

A shaking table test for a bridge foundation reinforced by anti-slide piles on a silty clay landslide model with an inclined interlayer was performed.The deformation characteristics of the bridge foundation piles and anti-slide piles were analyzed in different loading conditions.The dynamic response law of a silty clay landslide with an inclined interlayer was summarized.The spacing between the rear anti-slide piles and bridge foundation should be reasonably controlled according to the seismic fortification requirements,to avoid the two peaks in the forced deformation of the bridge foundation piles.The“blocking effect”of the bridge foundation piles reduced the deformation of the forward anti-slide piles.The stress-strain response of silty clay was intensified as the vibration wave field appeared on the slope.Since the vibration intensified,the thrust distribution of the landslide underwent a process of shifting from triangle to inverted trapezoid,the difference in the acceleration response between the bearing platform and silty clay landslide tended to decrease,and the spectrum amplitude near the natural vibration frequency increased.The rear anti-slide piles were able to slow down the shear deformation of the soil in front of the piles and avoid excessive acceleration response of the bridge foundation piles.

Dynamic Response of Foundations during Startup of High-Frequency Tunnel Equipment

The specialized equipment utilized in long-line tunnel engineering is evolving towards large-scale,multifunctional,and complex orientations.The vibration caused by the high-frequency units during regular operation is supported by the foundation of the units,and the magnitude of vibration and the operating frequency fluctuate in different engineering contexts,leading to variations in the dynamic response of the foundation.The high-frequency units yield significantly diverse outcomes under different startup conditions and times,resulting in failure to meet operational requirements,influencing the normal function of the tunnel,and causing harm to the foundation structure,personnel,and property in severe cases.This article formulates a finite element numerical computation model for solid elements using three-dimensional elastic body theory and integrates field measurements to substantiate and ascertain the crucial parameter configurations of the finite element model.By proposing a comprehensive startup timing function for high-frequency dynamic machines under different startup conditions,simulating the frequency andmagnitude variations during the startup process,and suggesting functions for changes in frequency and magnitude,a simulated startup schedule function for high-frequency machines is created through coupling.Taking into account the selection of the transient dynamic analysis step length,the dynamic response results for the lower dynamic foundation during its fundamental frequency crossing process are obtained.The validation checks if the structural magnitude surpasses the safety threshold during the critical phase of unit startup traversing the structural resonance region.The design recommendations for high-frequency units’dynamic foundations are provided,taking into account the startup process of the machine and ensuring the safe operation of the tunnel.

Application of strength reduction method to dynamic anti-sliding stability analysis of high gravity dam with complex dam foundation

Considering that there are some limitations in analyzing the anti-sliding seismic stability of dam-foundation systems with the traditional pseudo-static method and response spectrum method, the dynamic strength reduction method was used to study the deep anti-sliding stability of a high gravity dam with a complex dam foundation in response to strong earthquake-induced ground action. Based on static anti-sliding stability analysis of the dam foundation undertaken by decreasing the shear strength parameters of the rock mass in equal proportion, the seismic time history analysis was carried out. The proposed instability criterion for the dynamic strength reduction method was that the peak values of dynamic displacements and plastic strain energy change suddenly with the increase of the strength reduction factor. The elasto-plastic behavior of the dam foundation was idealized using the Drucker-Prager yield criterion based on the associated flow rule assumption. The result of elasto-plastic time history analysis of an overflow dam monolith based on the dynamic strength reduction method was compared with that of the dynamic linear elastic analysis, and the reliability of elasto-plastic time history analysis was confirmed. The results also show that the safety factors of the dam-foundation system in the static and dynamic cases are 3.25 and 3.0, respectively, and that the F2 fault has a significant influence on the anti-sliding stability of the high gravity dam. It is also concluded that the proposed instability criterion for the dynamic strength reduction method is feasible.

Optimization design of foundation excavation for Xiluodu super-high arch dam in China

With better understanding of the quality and physico-mechanical properties of rocks of dam foundation,and the physico-mechanical properties and structure design of arch dam in association with the foundation excavation of Xiluodu arch dam,the excavation optimization design was proposed for the foundation surface on the basis of feasibility study.Common analysis and numerical analysis results demonstrated the feasibility of using the weakly weathered rocks III1and III2as the foundation surface of super-high arch dam.In view of changes in the geological conditions at the dam foundation along the riverbed direction,the design of extending foundation surface excavation area and using consolidating grouting and optimizing structure of dam bottom was introduced,allowing for harmonization of the arch dam and foundation.Three-dimensional(3D)geomechanics model test and fi nite element analysis results indicated that the dam body and foundation have good overload stability and high bearing capacity.The monitoring data showed that the behaviors of dam and foundation correspond with the designed patterns in the construction period and the initial operation period.

Design of Large-Scale Prestressing Bucket Foundation for Offshore Wind Turbines

The key in the force transmission between the tower and the foundation for offshore wind turbines is to transfer the large moment and horizontal loads. The finite element model of a large-scale prestressing bucket founda- tion for offshore wind turbines is set up and the structural characteristics of the arc transition structure of the founda- tion are analyzed for 40-60 channels(20-30 rows) arranged with prestressing steel strand under the same ultimate load and boundary conditions. The mechanical characteristics of the key parts of the foundation structures are illus- trated by the peak of the principal tensile stress, the peak of the principal compressive stress and the distribution areas where the principal tensile stress is larger than 2.00 MPa. It can be concluded that the maximum principal tensile stress of the arc transition decreases with the increasing number of channels, and the amplitude does not change signifi- cantly; the maximum principal compressive stress increases with the increasing number of channels and the amplitude changes significantly; however, for the distribution areas where the principal tensile stress is larger than 2.00 MPa, with different channel numbers, the phenomenon is not obvious. Furthermore, the principal tensile stress at the top of the foundation beams fluctuantly increases with the increasing number of channels and for the top cover of the bucket, the principal tensile stress decreases with the increasing number of channels.

Study on Deep Well Dewatering Optimization Design in Deep Foundation Pit and Engineering Application

Based on analyses of the theories of groundwater unsteady flow in deep well dewatering in the deep foundation pit, Theis equations are chosen to calculate and analyze the relationship between water level drawdown of confined aquifer and dewatering duration. In order to reduce engineering cost and diminish detrimental effect on ambient surrounding, optimization design target function based on the control of confined water drawdown and four restriction requisitions based on the control of safe water level, resistance to throwing up from the bottom of foundation pit, avoiding excessively great subsidence and unequal surface subsidence are proposed. A deep well dewatering project in the deep foundation pit is optimally designed. The calculated results including confined water level drawdown and surface subsidence are in close agreement with the measured results, and the optimization design can effectively control both surface subsidence outside foundation pit and unequal subsidence as a result of dewatering.

Design parameter optimization of beam foundation on soft soil layer with nonlinear finite element

Finite element method was performed to investigate the influences of beam stiffness, foundation width and cushion thickness on the beating capacity of beam foundation on underlying weak laminated clay. The comparison between numerical results and results from field test including plate-bearing test and foundation settlement observation shows reasonable agreement. According to the numerical results, the beam width, length, cross section and cushion thickness were optimized. The results show that the stresses in subgrade soil decrease greatly with increasing the cushion thickness and width of foundation. However, the foundation settlement and influencing depth of displacement also increase correspondingly under conditions of relatively thinner cushion thickness. For the foundations on underlying weak layer, increasing foundation width merely might be inadequate for improving the bearing capacity, and the appropriate width and cushion thickness depend on the response of subgrade. A comparison between rigid and flexible beams was also discussed. The influence of a flexible beam foundation on subgrade is relatively smaller under the same loading conditions, and the flexible beam foundation appears more adaptable to various subgrades. The proposed flexible beam foundation was adopted in engineering. According to the calculation results, beam width of 2.4 m and cushion thickness of 0.8 m are proposed, and a flexible beam foundation is applied in the optimized design, which is confirmed reasonable by the actual engineering.

Design and construction of Sutong Bridge deep-water main-pylon foundations

This paper,from three aspects including construction conditions,foundation design and construction,introduces some considerations in the designing of main-pylon foundations and some practical measures to deal with certain unfavorable construction conditions,such as deep water,tidal effect,soft stratum and heavy traffic,during the construction of main-pylon foundations.

Vibration Isolation Characteristics of Impedance-balanced Ship Equipment Foundation under Unbalanced Excitation

A new type of impedance-balanced ship equipment foundation structure based on the principle of impedance balancing using a“discontinuous panel-vibration isolation liquid layer-foundation structure”is proposed to solve the problem of poor low-frequency vibration isolation of the foundation under unbalanced excitation of shipboard equipment.Based on the finite element method,the influence of characteristic parameters of the foundation panel structure on its vibration reduction characteristics under unbalanced excitation is explored.The results show that the vibration isolation level of the impedance-balanced foundation is 10 dB higher than the traditional foundation in the low-frequency band of 10-500 Hz when subjected to combined excitation of concentrated force and moment.Increasing the thickness of the impedance-balanced foundation panel can enhance the isolation effect.Increasing the number of sub-panels can effectively reduce the vibration response of the foundation panel and enhance the isolation performance of the foundation.The connection stiffness between sub-panels has a small effect on the isolation performance of the foundation.

Design of Foundations Built on a Shallow Depth (Less than 4 m) of Egyptian Macro-Porous Collapsible Soils

It is nowadays well reported that collapsible soils spread in many countries, including United States, Russia, China, South America (e.g. Brazil), South and North Africa (e.g. Egypt, Algeria), Middle East (e.g. Saudi Arabia) and many countries in Eastern Europe. In general, collapsible soils are located in arid and semi-arid regions around the world. This special type of soil is characterized by abrupt reduction in strength, excessive and sudden settlement when it becomes wet leading to failure of the structure. Construction on such a kind of soil is one of the prominent problems in geotechnical engineering. The main objectives of this study are reporting geological and geotechnical zonation maps for potentially collapsible soils in inhabited areas in Egypt. Furthermore, a design technique for foundations built on a shallow depth of Egyptian macro-porous collapsible soils (less than 4 m) is developed. The design method includes a design chart for soil collapse field classification in terms of the most governing parameters, a method for foundation settlement estimation based on a correlation between the wetting-induced collapse strain and the applied pressure, and a design practice to guide practicing engineers to select the appropriate foundation system to construct on such soil with a great degree of confidence and safety.

Spatially variable soils affecting geotechnical strip foundation design

Natural soil variability is a well-known issue in geotechnical design,although not frequently managed in practice.When subsoil must be characterized in terms of mechanical properties for infrastructure design,random finite element method(RFEM)can be effectively adopted for shallow foundation design to gain a twofold purpose:(1)understanding how much the bearing capacity is affected by the spatial variability structure of soils,and(2)optimisation of the foundation dimension(i.e.width B).The present study focuses on calculating the bearing capacity of shallow foundations by RFEM in terms of undrained and drained conditions.The spatial variability structure of soil is characterized by the autocorrelation function and the scale of fluctuation(δ).The latter has been derived by geostatistical tools such as the ordinary Kriging(OK)approach based on 182 cone penetration tests(CPTs)performed in the alluvial plain in Bologna Province,Italy.Results show that the increase of the B/δratio not only reduces the bearing capacity uncertainty but also increases its mean value under drained conditions.Conversely,under the undrained condition,the autocorrelation function strongly affects the mean values of bearing capacity.Therefore,the authors advise caution when selecting the autocorrelation function model for describing the soil spatial variability structure and point out that undrained conditions are more affected by soil variability compared to the drained ones.

Automated Design and Visualization System of a House Foundation from Blocks

This article analyzes creation methods of automated design system, presents design system of a house foundation from blocks. The creation methods of automated design system of a house foundation from blocks are discovered with Unified Modeling Language. Analyzed objects-classes： block, specification, model. Graphical system can design foundation, form specification of objects and create 3D model of house foundation. There are several types and different dimensions of concrete blocks. The program optimally arranges selected blocks so that monolithic parts will be minimal volume. Program selects a house foundation blocks from database by using ActiveX Data Objects technology, which by programming method connects drawing and database. Drawing＇s graphical objects have additional data from which exchange of data between graphical system and database is executed. Visualization system and example of house foundation from blocks project with specifications is presented. Creation problems of automated design system are discussed and conclusions are made.

Design and Engineering of Urban Interchange Ramp Bridge Structure

This paper analyzes the structural design of an urban interchange ramp bridge from four aspects,which are the superstructure,pier structure,foundation structure,and deck structure design to summarize the structural design ideas of this urban interchange ramp bridge,which can be used as a reference for future construction of the same bridge.

Design Methodology Research of the Floating Foundation for the Offshore MW-Rating Wind Turbine

With the rapid growth of the offshore wind industry, the innovative floating offshore wind turbine is chosen as the most feasible device to harvest the vast wind energy in deep water area. However there is no practical design guide for the floating wind turbine especially the floating foundation. In this paper, based on the investigation on the worldwide floating wind turbine and current available expertise on floating platforms accumulated in offshore O/G （oil and gas） industry, an integrated design methodology is presented according to the specialized characteristics of wind turbine, including the type selection of foundation and mooring system, design standard, design procedure, design conditions, key technologies involved. Finally a semi-submersible floating foundation is designed to support certain megawatt-rating wind turbine of Goldwind and also performance analysis and code checks are performed to validate the design. The design method of the floating foundation provided in this paper is proved feasible and can be adopted in practical engineering design.

Foundation的设计输入方法

介绍了xilinx公司的EDA软件Foundation的各种输入方法,并举例说明它们之间的组合应用。

Reinforcement of Soft Foundation with Geotextile and Observation for Sea Dike Project of Zhapu Port

The design method of reinforcement of soft foundation with geotextile for the sea dike of the Zhapu Port is discussed in this paper. The prototype behaviours such as pore water pressure, settlement and so on were observed. The degree of consolidation is found out from observed pore water pressure and observed settlement respectively, then the strength increment of soil is calculated and compared with that obtained from vane shear tests. For the use of observed pore water pressure, the consolidation coefficient of soil is deduced approximately with a method named experimental exponential interpolation. The degree of consolidation of the ground is deduced theoretically from the dissipation of pore water pressure. Besides, the logarithmic curve and hyperbola are used to fit the observed time-settlement curve, and the degree of consolidation of soil is obtained according to the definition of the consolidation degree. After preliminary verification with observed prototype data, the method to reinforce the low dike with geotextile is considered to be simple and rational, and it can also reduce the construction cost.

Foundation Assessment in Different Parts of Iraq Using STAAD Pro V8i

Foundation is considered as one of the main parts of any structure. The type of foundation used is highly dependent on the type and properties of soil. The design of foundations requires many factors that should be defined. There are number of differences in the geological and soil conditions in Iraq. As a consequence, these differences are reflected on the type of foundation to be used. Despite these differences, same materials and style of buildings are used all over Iraq. The main problems of Iraqi soil are high gypsum content, salinity and shallow water table depth. These factors that influence the foundations are the soil properties and the amount of loads that transmitted by the superstructure. The situation has been analysed through a case study which illustrated the link between soil and foundation types in three different parts of Iraq （Mosul, Baghdad and Basra）. One building was analysed using ＂STAAD （structural analysis and design）. Pro＂ software in these regions. It is evident that Iraqi designers and engineers require local code to define all the loads, materials and design of the foundation to be used. The use of local materials might be very effective from both engineering and economic perspectives.