Influence of Incomplete Soil Plugs on Bearing Capacities of Bucket Foundations in Clay

Due to the uneven seabed and heaving of soil during pumping,incomplete soil plugs may occur during the installation of bucket foundations,and the impacts on the bearing capacities of bucket foundations need to be evaluated.In this paper,the contact ratio(the ratio of the top diameter of the soil plug to the diameter of the bucket)and the soil plug ratio(the ratio of the soil heave height to the skirt height)are defined to describe the shape and size of the incomplete soil plug.Then,finite element models are established to investigate the bearing capacities of bucket foundations with incomplete soil plugs and the influences of the contact ratios,and the soil plug ratios on the bearing capacities are analyzed.The results show that the vertical bearing capacity of bucket foundations in homogeneous soil continuously improves with the increase of the contact ratio.However,in normally consolidated soil,the vertical bearing capacity barely changes when the contact ratio is smaller than 0.75,while the bearing capacity suddenly increases when the contact ratio increases to 1 due to the change of failure mode.The contact ratio hardly affects the horizontal bearing capacity of bucket foundations.Moreover,the moment bearing capacity improves with the increase of the contact ratio for small aspect ratios,but hardly varies with increasing contact ratio for aspect ratios larger than 0.5.Consequently,the reduction coefficient method is proposed based on this analysis to calculate the bearing capacities of bucket foundations considering the influence of incomplete soil plugs.The comparison results show that the proposed reduction coefficient method can be used to evaluate the influences of incomplete soil plug on the bearing capacities of bucket foundations.

Integration of GIS with the Generalized Reciprocal Method(GRM)for Determining Foundation Bearing Capacity:A Case Study in Opolo,Yenagoa Bayelsa State,Nigeria

This study addresses the pressing need to assess foundation bearing capacity in Opolo,Yenagoa,Bayelsa State,Nigeria.The significance lies in the dearth of comprehensive geotechnical data for construction planning in the region.Past research is limited and this study contributes valuable insights by integrating Geographic Information System(GIS)with the Generalized Reciprocal Method(GRM).To collect data,near-surface seismic refraction surveys were conducted along three designated lines,utilizing ABEM Terraloc Mark 6 equipment,Easy Refract,and ArcGIS 10.4.1 software.This methodology allowed for the determination of key geotechnical parameters essential for soil characterization at potential foundation sites.The results revealed three distinct geoseismic layers.The uppermost layer,within a depth of 0.89 to 1.50 meters,exhibited inadequate compressional and shear wave velocities and low values for oedometric modulus,shear modulus,N-value,ultimate bearing capacity,and allowable bearing capacity.This indicates the presence of unsuitable,soft,and weak alluvial deposits for substantial structural loads.In contrast,the second layer(1.52 to 3.84 m depth)displayed favorable geotechnical parameters,making it suitable for various construction loads.The third layer(15.00 to 26.05 m depth)exhibited varying characteristics.The GIS analysis highlighted the unsuitability of the uppermost layer for construction,while the second and third layers were found to be fairly competent and suitable for shallow footing and foundation design.In summary,this study highlights the importance of geotechnical surveys in Opolo’s construction planning.It offers vital information for informed choices,addresses issues in the initial layer,and suggests secure,sustainable construction options.

Estimation of Undrained Bearing Capacity for Offshore Soft Foundations with Cyclic Load

The degradation strength of soils under cyclic loading is studied and a method for determining the cyclic degradation strength with cyclic triaxial tests is given in the paper. Furthermore, a dum my static method for estimating the undrained bearing capacity for offshore soft foundation under wave loads is developed. It can consider the effect of the difference of cyclic stress for different parts of the foundation on both the degradation strength of the foundation soil and the bearing capacity so that the estimated result can better reflect the real condition of foundation under cyclic loading. The method can be applied to plane and space problem.

Empirical methods for determining shaft bearing capacity of semi-deep foundations socketed in rocks

Semi-deep foundations socketed in rocks are considered to be a viable option for the foundations in the presence of heavy load imposed by high-rise structures, due to the low settlement and high bearing capacity. In the optimum design of semi-deep foundations, prediction of the shaft bearing capacity, rs, of foundations socketed in rocks is thus critically important. In this study, the unconfined compressive strength(UCS), qu, has been applied in order to investigate the shaft bearing capacity. For this, a database of 106 full-scale load tests is compiled with UCS values of surrounding rocks, in which 34 tests with rock quality designation(RQD), and 5 tests with rock mass rating(RMR). The bearing rocks for semi-deep foundations include limestone, mudstone, siltstone, shale, granite, tuff, granodiorite, claystone, sandstone, phyllite, schist, and greywacke. Using the database, the applicability and accuracy of the existing empirical methods are evaluated and new relations are derived between the shaft bearing capacity and UCS based on the types of rocks. Moreover, a general equation in case of unknown rock types is proposed and it is verified by another set of data. Since rock-socketed shafts are supported by rock mass(not intact rock), a reduction factor for the compressive strength is suggested and verified in which the effect of discontinuities is considered using the modified UCS, qu(modified), based upon RMR and RQD in order to take into account the effect of the rock mass properties.

Lateral Bearing Capacity of Multi-Bucket Foundation in Soft Ground

The bucket foundation is a new type of foundation for offshore application to intermediate-depth waters. It has advantages over conventional ones. However, there is no consensus in the analysis and design of this type of foundation. In this paper, the lateral bearing capacity and the failure mechanism of multi-bucket foundations are studied with different connection stiffness and bucket spacing by use of a three-dimensional finite element method. Based on the numerical analysis results, a limit analysis method of plasticity for evaluating the lateral bearing capacity of large-spacing multi- bucket foundation with rigid connection in soft ground is proposed. This method provides a simple procedure that gives results comparable to those from the finite element analyses.

Probabilistic analysis of ultimate seismic bearing capacity of strip foundations

This paper presents a reliability analysis of the pseudo-static seismic bearing capacity of a strip foundation using the limit equilibrium theory. The first-order reliability method(FORM) is employed to calculate the reliability index. The response surface methodology(RSM) is used to assess the Hasofer e Lind reliability index and then it is optimized using a genetic algorithm(GA). The random variables used are the soil shear strength parameters and the seismic coefficients(khand kv). Two assumptions(normal and non-normal distribution) are used for the random variables. The assumption of uncorrelated variables was found to be conservative in comparison to that of negatively correlated soil shear strength parameters. The assumption of non-normal distribution for the random variables can induce a negative effect on the reliability index of the practical range of the seismic bearing capacity.

New design equations for estimation of ultimate bearing capacity of shallow foundations resting on rock masses

Rock masses are commonly used as the underlying layer of important structures such as bridges, dams and transportation constructions. The success of a foundation design for such structures mainly depends on the accuracy of estimating the bearing capacity of rock beneath them. Several traditional numerical approaches are proposed for the estimation of the bearing capacity of foundations resting on rock masses to avoid performing elaborate and expensive experimental studies. Despite this fact, there still exists a serious need to develop more robust predictive models. This paper proposes new nonlinear prediction models for the ultimate bearing capacity of shallow foundations resting on non-fractured rock masses using a novel evolutionary computational approach, called linear genetic programming. A comprehensive set of rock socket, centrifuge rock socket, plate load and large-scaled footing load test results is used to develop the models. In order to verify the validity of the models, the sensitivity analysis is conducted and discussed. The results indicate that the proposed models accurately characterize the bearing capacity of shallow foundations. The correlation coefficients between the experimental and predicted bearing capacity values are equal to 0.95 and 0.96 for the best LGP models. Moreover, the derived models reach a notably better prediction performance than the traditional equations.

Characteristic Test Study on Bearing Capacity of Suction Caisson Foundation Under Vertical Load

Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion.In order to study the uplift bearing mechanism and failure mode of suction caisson foundation,a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode.Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity.The smaller the permeability coefficient is,the higher the residual negative pressure will be.And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson.When the load reaches the ultimate bearing capacity,both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay.Combined the uplift bearing characteristics of caisson in sandy soil and soft clay,the bearing capacity composition and the calculation method are proposed.It can provide a reference for the engineering design of suction caisson foundation under vertical load.

Upper Bound Solutions for Uplift Ultimate Bearing Capacity of Suction Caisson Foundation

Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson and the failure mode of suction caisson foundation subjecting pullout loading behaves as a reverse compression failure mechanism.The upper bound theorems have been proved to be a powerful method to find the critical failure mechanism and critical load associated with foundations, buried caissons and other geotechnical structures. However, limited attempts have been reported to estimate the uplift bearing capacity of the suction caisson foundation using the upper bound solution. In this paper, both reverse failure mechanisms from Prandtl and Hill were adopted as the failure mechanisms for the computation of the uplift bearing capacity of the suction caisson. New equations were proposed based on both failure mechanisms to estimate the pullout capacity of the suction caisson. The proposed equations were verified by the test results and experimental data from published literature. And the two solutions agree reasonably well with the other test results. It can be proved that both failure mechanisms are reasonably and more consistent with the actual force condition.

Effect of Bearing Capacity on Designing Foundations in Iraq Using STAAD Pro-v8i

Most of Iraqi soil is classified as Quaternary deposits, especially in the Mesopotamian plain and tributaries of the River Tigris. Soil varies from north to south of Iraq. These differences in soil affected the process to select the suitable type of foundation. This research is to study the effect of bearing capacity on shallow foundations in different regions of Iraq. Seventy nine samples were collected from 23 boreholes at three different locations (Mosul at the North, Baghdad at the middle and Basrah at the south of Iraq). The samples were collected at varying depth between 1 to 24 m. They were subjected to the following testes: Atterberg limits, sieve and hydrometers, consolidation, direct shear, unconfined compression and the filed (SPT test). The values of the bearing capacity parameters ( and c) were obtained from the above tests. The results obtained were used in the application of the general equation of the bearing capacity. Then, the model of a building was designed (two floors, with mat foundation type) using STAAD Pro software. The average values of bearing capacity in each region were applied in the program (Mosul = 177 KPa, Baghdad = 125 KPa and Basrah = 84 KPa). In addition, the worst bearing capacity values were also used for the three regions (Mosul = 77 KPa, Baghdad = 68 KPa and Basrah = 24 KPa). The results obtained from the average and worst bearing capacity indicated that for Mosul, we could use shallow foundation (spread and mat used if there was basement) for different areas and for buildings with many stories. For Baghdad region, shallow foundation was more suitable for building not higher than five stories. Finally, for Basrah region, shallow foundations were an appropriate selection, but for most areas deep foundation was the right choice.

Bearing Capacity and Technical Advantages of Composite Bucket Foundation of Offshore Wind Turbines

Based on mechanical characteristics such as large vertical load,large horizontal load,large bending moment and complex geological conditions,a large scale composite bucket foundation (CBF) is put forward.Both the theoretical analysis and numerical simulation are employed to study the bearing capacity of CBF and the relationship between loads and ground deformation.Furthermore,monopile,high-rise pile cap,tripod and CBF designs are compared to analyze the bearing capacity and ground deformation,with a 3-MW wind generator as an example.The results indicate that CBF can effectively bear horizontal load and large bending moment resulting from upper structures and environmental load.

Bearing capacity and mechanical behavior of CFG pile composite foundation

CFG pile (i.e., pile constructed by granular materials of cement, fly-ash and gravel) composite foundation is applied in subsoil treatment widely and successfully. In order to have a further study of this kind of subsoil treatment technology, the influencing factors and calculation methods of the vertical bearing capacity of single CFG pile and the CFG pile composite foundation were discussed respectively. And based on the obtained solutions, effects by the cushion and measurements to reduce negative friction area were analyzed. Moreover, the developing law of settlement and bearing capacity eigenvalue controlled by the material strength with the increase of load were given for the CFG composite foundation. The in-situ static load test was tested for CFG pile. The results of test show that the maximum test load or half of the ultimate load is used from all the points of test, the average bearing capacity eigenvalue of single pile is 390 kN, and slightly greater than the design value of bearing capacity. The bearing capacity eigenvalues of composite foundation for 3 piles are greater than 300 kPa, and the mechanical properties of CFG pile composite foundation are almost identical in the case of the same load and cushion thickness. The pile-soil stress ratio and the load-sharing ratio can be adjusted through setting up cushion thickness.

Numerical analysis on bearing capacity of middle pylon caisson foundation of Taizhou Bridge

Because of the computation difficulty of the bearing capacity of large underwater caisson foundation on thick overburden layer ground, the geotechnical software FLAC3D was utilized in the 3D numerical analysis on the bearing capacity of middle pylon foundation. From the computational results, it is concluded that the caisson foundation has a good bearing capacity on thick overburden layer ground and the bearing capacity can be improved assuming that the soil near the area of basal corner is reinforced.

One-Step-Installation of Offshore Wind Turbine on Large-Scale Bucket-Top-Bearing Bucket Foundation

In 2010,the first offshore wind turbine with integrated installation was established in Qidong sea area of Jiangsu Province,China,which led to the implementation phase of one-step-installation technique based on the design and construction of large-scale bucket-top-bearing (LSBTB) bucket foundation.The critical technique of LSBTB bucket foundation included self-floating towing,penetration with adjustment of horizontal levelness,removability and one-step-installation.The process of one-step-installation included the prefabrication of LSBTB bucket foundation in onshore construction base,installation and debugging of wind power,overall water transportation of foundation and wind power system,and installation of foundation and offshore wind turbine on the appointed sea area.The cost of one-step-installation technique was about 5 000 Yuan/kW,which was 30%-50% lower than that of the existing technique.The prefabrication of LSBTB bucket foundation took about two months.During the one-step-installation process,the installation and debugging of wind power and overall water transportation need about one to two days in sea area within 35 m depth.After the proposed technique is industrialized,the cost will be further reduced,and the installation capacity is expected to be up to 500 wind turbines per year.

Test on Muddy Soil Reinforcement by Negative Pressure and Electro-Osmosis Inside Cover-Bearing-Type Bucket Foundation for Offshore Wind Turbines

Cover-bearing-type bucket foundation for offshore wind turbines has been paid more and more attention due to its low cost and great bearing capacity. In order to ensure the cover-bearing mode, the muddy soil inside the bucket foundation should be reinforced by some soil consolidation methods, such as negative pressure and electro-osmosis. Firstly, tests were conducted to obtain the reasonable current density. Meanwhile, to improve the electro-osmotic speed and effectiveness, other factors such as intermittent power and layout of electrode, were also studied in the tests. Then, the soil reinforcing tests by negative pressure combined with electro-osmosis were performed for the muddy soil consolidation inside the bucket foundation. The results showed that soil reinforcement by negative pressure was quicker and more obvious during the early phase, and electro-osmotic method can affect more range of soil by rational arrangement of electrodes. Compared with negative pressure, the electro-osmotic method was a continuous and relatively slow process of reinforcement, which was complementary to the negative pressure method. The voltage value of electro-osmosis had little effect on the muddy soil reinforcement inside the bucket foundation, and 1.5 A was chosen as the most reasonable current value for scale model testing in the electro-osmotic method.

Reply to Discussion on “Empirical methods for determining shaft bearing capacity of semi-deep foundations socketed in rocks”

Semi-deep foundations socketed in rocks are considered to be a viable option for the foundations in the presence of heavy loads imposed by high-rise buildings and special structures, due to the low settlement and high bearing capacity. In this study, the unconfined compressive strength（UCS） and rock mass cuttability index（RMCI） have been applied to investigating the shaft bearing capacity. For this purpose, a comprehensive database of 178 full-scale load tests is compiled by adding a data set（n = 72）collected by Arioglu et al.（2007） to the data set（n = 106） presented in Rezazadeh and Eslami（2017）.Using the database, the applicability and accuracy of the existing empirical methods are evaluated and new relations are derived between the shaft bearing capacity and UCS/RMCI. Moreover, a general equation in case of unknown rock types is proposed and it is verified by another set of data（series 3 in Rezazadeh and Eslami（2017））. Since rock-socketed shafts are supported by rock mass（not intact rock）,a reduction factor for the compressive strength is suggested and verified in which the effect of discontinuities is considered using the modified UCS, based upon RMR and RQD to consider the effect of the rock mass properties.

Semi-Deep Skirted Foundations and Numerical Solution to Evaluate Bearing Capacity

Semi-deep foundations are a remarkable solution in conditions where the soil beneath the foundation is loose to a great depth and there is no possible way to use any way of soil improvement and applying piles would not be a logical way considering their cost and time of enforcing. Skirted foundations are a type of semi-deep foundations that can penetrate to the soil up to two times of their breadth. Estimating bearing capacity of these foundations is a long geotechnical problem for engineers whether under absolute or combined loading because of their usage in offshore and onshore projects. For estimating the vertical bearing capacity of these foundations, series of finite element analyses were performed for a range of embedment ratios to investigate the effect of the length of the skirt. The foundation has been modelled with two different types of soil and the results validated with previous analytical, numerical and experimental researches. In addition, the bearing capacity of a skirted foundation under combined loading in V-H space has been analyzed by this approach and the 2-dimentional failure envelope has been presented.

Upper Bound Solution of the Resisting Moment Bearing Capacity of A Composite Bucket Shallow Foundation of An Offshore Wind Turbine in Sand

Bearing the large moment that is generated by the wind load that acts on the upper structure of offshore wind turbines is an important feature of their foundations that is different from other offshore structures.A composite bucket shallow foundation(CBSF)has been proposed by Tianjin University to address the soft geological conditions in the offshore regions of China for wind turbines.The CBSF is a new type of foundation and is effective against large moments.The soil deformation test of a CBSF and the numerical simulation study under the same working conditions are carried out to determine the failure mechanism of a CBSF under moment loading.The resisting soil compression rateηm is defined as a new empirical parameter that indicates the ability of the soil inside the bucket to resist moment loading.The upper limit of the resisting moment bearing capacity of the bucket foundation is derived through the upper bound theorem of classical plasticity theory based on the failure mechanism.The calculation method is validated by tests of bucket models with different height-diameter ratios in sand under moment loading.

Calculation and Analysis of Bearing Capacity of Double-Layer Foundation Based on Prandtl Assumption

Based on the basic concept of Plandell's assumption,the plasticity balance principle is applied to analyze the bearing capacity of the two-layer foundation,and the formula of bearing capacity of the two-layer foundation is obtained.The variation of bearing capacity of the foundation under different soil conditions is analyzed,and different calculation parameters are obtained.The effect on the ultimate bearing capacity of the two-layer foundation.The study found that:(1)For homogeneous soils,the formula obtained in this paper is the same as the Plandell formula;(2)the cohesive force of the soil,the soil bulk density above the foundation,and the aspect ratio have less influence on the bearing capacity of the foundation than the internal friction angle.Much;(3)The upper and lower layers of different strength ratios have different critical depths and increase with the increase of the relative strength of the upper layers.(4)This paper assumes that the foundation is completely smooth and ignores the influence of the bulk density of the foundation soil,which is not consistent with sand.

Methods for Estimating the Ultimate Bearing Capacity of Layered Foundations

The Meyerhof and Hanna′s(M-H) method to estimate the ultimate bearing capacity of layered foundations was improved. The experimental results of the load tests in Tianjin New Harbor were compared with predictions with the method recommended by the code for the foundations of harbor engineering, i.e. Hansen′s method and the improved M-H method. The results of the comparisons implied that the code and the improved M-H method could give a better prediction.