Robust Nonlinear Current Sensorless Control of the Boost Converter with Constant Power Load

The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the design of stabilizing controllers. A PWM-based current-sensorless robust sliding mode controller is developed that requires only the measurement of the output voltage. An extended state observer is developed to estimate a lumped uncertainty signal that comprises the uncertain load power and the input voltage, the converter parasitics, the component uncertainties and the estimation of the derivative of the output voltage needed in the implementation of the controller. A linear sliding surface is used to derive the controller, which is simple in its design and yet exhibits excellent features in terms of robustness to external disturbances, parameter uncertainties, and parasitics despite the absence of the inductor’s current feedback. The robustness of the controller is validated by computer simulations.

RELIABLE HYSTERESIS CURRENT CONTROLLED DUAL BUCK HALF BRIDGE INVERTER

A highly efficient and re liable topology-dual buck half bridge inverter (DBI) is introduced. The existenc e of discontinuous conduction mode (DCM) operation state requires the bias of in du ctor current for DBI implemented with linear controllers like ramp comparison SP WM (RCSPWM) controllers. A novel operation scheme for DBI and a hysteresis curre nt controlled dual buck half bridge inverter (HCDBI) are proposed. The bias curr ent required by RCSPWM DBI is eliminated and conduction losses are dramatically reduced. HCDBI has greatly improved the modulation performance in DCM region for the benefit of its excellent command tracking capability. The operational schem e and control strategy are presented. Power losses of the conventional half brid ge inverter (CHBI) and HCDBI are compared with mathematical computation, and exp erimental verification is also executed. Both calculational and experimental res ults verify that HCDBI has a superior switching performance over CHBI. Its exce llent high frequency operational capacity provides another access to realize high fre quency operation of inverters.

Fault tolerant control of electric pitch control system based on single current detection

In view of the current sensors failure in electric pitch system,a variable universe fuzzy fault tolerant control method of electric pitch control system based on single current detection is proposed.When there is single or two-current sensor fault occurs,based on the proposed method the missing current information can be reconstructed by using direct current（DC）bus current sensor and the three-phase current can be updated in time within any two adjacent sampling periods,so as to ensure stability of the closed-loop system.And then the switchover and fault tolerant control of fault current sensor would be accomplished by fault diagnosis method based on adaptive threshold judgment.For the reconstructed signal error caused by the modulation method and the main control target of electric pitch system,a variable universe fuzzy control method is used in the speed loop,which can improve the anti-disturbance ability to load variation,and the robustness of fault tolerance system.The results show that the fault tolerant control method makes the variable pitch control system still has ideal control characteristics in case of sensor failure although part of the system performance is lost,thus the correctness of the proposed method is verified.

Design and analysis of dual-mode structure repetitive control based hybrid current regulation scheme for active power filters

An all-digital hybrid current regulation scheme for the single-phase shunt active power filter （APF） is presented. The proposed hybrid current control scheme integrates the deadbeat control and the dual-mode structure repetitive control （DMRC） so that it can offer superior steady-state performance and good transient features. Unlike the conventional schemes, the proposed scheme-based APF can compensate both the odd and the even order harmonics in grid. The detailed design criteria and the stability analysis of the proposed hybrid current controller are presented. Moreover, an improved structure which incorporates the proposed hybrid controller and the resonant controller for tracking specific order harmonics is given. The relationships between the resonant controller and different repetitive control schemes are discussed. Experimental results verify the effectiveness and advantages of the proposed hybrid control scheme.

Application of a Current and Voltage Mixed Control Mode for the New Fast Control Power Supply at EAST

A feedback control system is needed to restrain plasma vertical displacement in EAST （Experimental Advanced Superconducting Toknmak）. A fast control power supply excites active feedback coils, which produces a magnetic field to control the plasma＇s displacement. With the development of EAST, new demands on the new fast control power supply have led to an enhanced ability of fast response and output current, as well as a new control mode. The structure of cascaded and paralleled H-bridges can meet the demand of extended capacity, and digital control can reMize current and voltage mixed control mode. The validity of the proposed scheme is confirmed by experiments.

Effects of current waveform parameters during droplet transfer on spatter in high speed waveform controlled Short-circuiting GMAW

Aim at improving the stability of the Short-circuiting Gas Metal Arc Welding （GMAW-S） process for the enhanced speed usage, effects of current waveform parameters during short-term on the welding stability have been investigated by experimental method. The welding power source used for the research is an inverter with a special current waveform control. It is shown that the spatter decreases at first then increases with each increase of the low current period, current increase rate and the maximum current limit. The test results are provided for welding of 1 mm and 3 mm mild steel at speed of 1.2 m/min. The stable GMA W-S process under high speed welding condition has been achieved by optimizing the parameters.

Reaction Selectivity Improvement for Reduction of Nitrobenzene in a Packed-Bed Electrode Reactor under Periodic-Current Control

Rectangular wave current control of the electrochemical reduction of nitrobenzene im-proves the selectivity for p-aminophenol(PAP) compared to direct current(d.c.) control at thesame average current density in a flow-by packed-bed reactor.Optimal increase in PAP selectivitycan be obtained at about a frequency of 50Hz and a duty cycle of 0.2.A mathematical model isset up to incorporate the effects of mass transfer,hydrogen evolution and double layer charging,and is solved using the Duhamel’s superposition principle and the modified Crank-Nicolson methodwith the upwind scheme.The conventional d.c.control cases are also calculated for comparison.Calculations can be applied to predict the reaction results under periodic current and d.c.control,but both display the same trends compared to experimental data.

Energy-Based Current Control for Stabilizing a Flexible Electrodynamic Tether System

An energy-based controller of electric current is synthesized for the libration stabilization of an electrodynamic tether system,which consists of a relatively large main-satellite and a sub-satellite of much smaller size.Two dynamic models with different levels of accuracy are considered in this work.First,a dumbbell model of the system is used for the controller design,which aims at damping injection on the libration motions via the real-time regulation of the electric current.Furthermore,the efficacy and performance of the proposed scheme are numerically verified by using a more complex multi-body model which accounts for not only the tether flexibility but also the attitude of the main-satellite.

Online Learning Control for Harmonics Reduction Based on Current Controlled Voltage Source Power Inverters

Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.

Research on Pitch Control Strategies of Horizontal Axis Tidal Current Turbine

Based on blade element momentum theory and generator characteristic test,a dynamic simulation model of 150 kW horizontal-axis tidal current turbine was established.The matching of the dynamic characteristics between the turbine and generator under various current velocities is studied,and the influence of the pitch angle on the matching is analyzed.For the problem of maximum power output in case of low current speed and limiting power in high current speed,the relation between optimal pitch angle and output power is analyzed.On the basis of dynamic characteristic analysis,the variable pitch control strategy is developed.The performance of the turbine under various tidal conditions is simulated.The research results show that the designed controller enables the turbine to operate efficiently under the condition of low current speed,and achieve the goal of limited power at high current speed.

Growth and passivation of aluminum etch tunnels at on-off controlling direct current in 6 wt.% HCI solution

Growth and passivation of tunnels within Al foil by on-off controlling DC etching in 6 wt.% HCI solution has been investigated. It was found that, in a given etchant solution at a special temperature, the longest tunnel length was only a function of the turn-on interval of DC. The potential of Al foil broke at on-off controlling DC by the result from anode polarization curves and potential-time （E-t） responding curves. When DC was switched on, the potential increased abruptly over pitting potential, leading to nucleation of pits at the surface and the growth of tunnels at special length. When DC was switched off, the potential decreased rapidly to a passive value, leading to stoppage of nucleation and death of tunnels. By this way, the longest tunnel length can be controlled and a non-piercing layer can be obtained. Hence, etching of Al foil at this current is beneficial for maintaining a good mechanical strength.

Model Predictive Current Control with Adaptive-adjusting Timescales for PMSMs

A model predictive current control(MPCC)with adaptive-adjusting method of timescales for permanent magnet synchronous motors(PMSMs)is proposed in this paper to improve the dynamic response and prediction accuracy in transient-state,while lessening the computational burden and improving the control performance in steady-state.The timescale characteristics of different parts of MPCC,such as signal sampling,prediction calculation,control output,model error correction,are analyzed,and the algorithm architecture of MPCC with multi-timescale is proposed.The difference between reference and actual speed,and the change rate of actual speed are utilized to discriminate the transient state of speed change and load change,respectively.Adaptive-adjusting method of control period and prediction stepsize are illustrated in detail after operation condition discrimination.Experimental results of a PMSM are presented to validate the effectiveness of proposed MPCC.In addition,comparative evaluation of single-step MPCC with fixed timescale and proposed MPCC is conducted,which demonstrates the superiority of proposed control strategy.

Hybrid Predictive Control with Simple Linear Control Based Circulating Current Suppression for Modular Multilevel Converters

The modular multilevel converter(MMC)has become a promising topology for widespread power converter applications.However,an evident circulating current flowing between the phases will increase system losses and complicate the heatsink design.This paper proposes a novel hybrid model predictive control method for MMCs.This method utilizes an indirect structure MPC and a sorting algorithm to implement current tracking and capacitor voltages balancing,considerably resulting in reduced calculation burden.In addition,different from the conventional MPC solutions,we add a simple proportional-integral(PI)controller to suppress circulating current through modifying the submodule(SM)inserted number,which is parallel to the MPC loop.This hybrid control solution combines both advantages of MPC and linear control,evidently resulting in improved performance of circulating current.Finally,the MATLAB/Simulink results of an 11-level MMC system verify the effectiveness of the proposed solution.

Current Situation and Comprehensive Control Measures of Water Environment in the Chaohu Lake

Based on the analysis of current situation of water environment in the Chaohu Lake,general ideas and measures of controlling the water environment were proposed. In respect of control ideas,controlling outbreaks of blue-green algae should be as one of control goals; it is needed to combine reducing the quantity of blue-green algae with decreasing eutrophication level to make the decrease in the quantity of blue-green algae larger than their natural increase until outbreaks of blue-green algae are eliminated; all kinds of techniques should be combined closely,integrated and innovated,and corresponding safeguard measures should be adopted. In respect of control measures,controlling sources of pollution and intercepting pollutants are basic measures,of which improving sewage treatment capacity and standard greatly is a key measure,and actively controlling pollution from large-scale livestock and poultry breeding is one of main measures; rivers polluted heavily should be controlled,and using microorganisms to purify small and moderate rivers can be as one of preferred techniques; blue-green algae should be dredged deeply to reducing their quantity; water should be transferred from the Yangtze River to the Chaohu Lake or the Hauihe River to purify water bodies and increase environmental capacity; reed wetland should be restored on a large scale to increase vegetation coverage from 5% to 20%; dredging should be combined with the elevation of basement of restored reed wetland.

Predictive current control system of PMSM based on LADRC

For a permanent magnet synchronous motor(PMSM)model predictive current control(MPCC)system,when the speed loop adopts proportional-integral(PI)control,speed regulation is easily affected by motor parameters,resulting in the inability to balance the system robustness and dynamic performance.A PMSM optimal control strategy combining linear active disturbance rejection control(LADRC)and two-vector MPCC(TV-MPCC)is proposed.Firstly,a mathematical model of a PMSM is presented,and the PMSM TV-MPCC model is developed in the synchronous rotation coordinate system.Secondly,a first-order LADRC controller composed of a linear extended state observer and linear state error feedback is designed to reduce the complexity of parameter tuning while linearly simplifying the traditional active disturbance rejection control(ADRC)structure.Finally,the conventional PI speed regulator in the motor speed control system is replaced by the designed LADRC controller.The simulation results show that the speed control system using LADRC can effectively deal with the changes in motor parameters and has better robustness and dynamic performance than PI control and similar methods.The system has a fast motor speed response,small overshoot,strong anti-interference,and no steady-state error,and the total harmonic distortion is reduced.

Adaptive controller design based on input-output signal selection for voltage source converter high voltage direct current systems to improve power system stability

An input-output signal selection based on Phillips-Heffron model of a parallel high voltage alternative current/high voltage direct current(HVAC/HVDC) power system is presented to study power system stability. It is well known that appropriate coupling of inputs-outputs signals in the multivariable HVDC-HVAC system can improve the performance of designed supplemetary controller. In this work, different analysis techniques are used to measure controllability and observability of electromechanical oscillation mode. Also inputs–outputs interactions are considered and suggestions are drawn to select the best signal pair through the system inputs-outputs. In addition, a supplementary online adaptive controller for nonlinear HVDC to damp low frequency oscillations in a weakly connected system is proposed. The results obtained using MATLAB software show that the best output-input for damping controller design is rotor speed deviation as out put and phase angle of rectifier as in put. Also response of system equipped with adaptive damping controller based on HVDC system has appropriate performance when it is faced with faults and disturbance.

Design of a Control Device for Synthetic Making Test Based on Pre-Arcing Current Detection and Phase Control

The synthetic making test has been widely used in evaluating the break ability of high-voltage circuit breaker. However, the test research and application are still inadequate, especially in the condition of rated voltage. According to the realistic conditions of test stations in China, a control device based on pre-arcing current detection and phase control is proposed in this paper. A sample of the control device made up of DSP TMS320LF2407A is fabricated, in which the CPLD MAX7064 is used to transmit signals for EMC design. It can be applied in full voltage synthetic making test at a level of 126kV/63kA. The test results show that, it is accurate to control the making phase of the applied voltage, whether the closing is demanded at voltage peak or zero.

The Current Status and Challenges Regarding Tuberculosis Infection Control in Health Care Facilities in China

Health care facilities are a high-risk environment for generating and spreading respiratory infectious diseases such as tuberculosis （TB）. The TB prevention and treatment staff in health care facilities are responsible for the identification, diagnosis, treatment, supervision, and management of TB patients .

Flow separation control over an airfoil using continuous alternating current plasma actuator

The flow separation control over an NACA 0015 airfoil using continuous alternating current(AC)dielectric barrier discharge(DBD)plasma actuator is investigated experimentally and numerically.This work is intended to report some observations made from our experiment,to which little attention is paid in the previous studies,but which is thought to be important to the understanding of control of complex flow separation with AC DBD.To this end,the response of separated flow to AC plasma actuation is visualized through the time-resolved particle image velocimetry(PIV)measurement,whereas numerical simulation is carried out to complement the experiment.The flow control process at chord-based Reynolds number(Re)of 3.31×105 is investigated.It is found that the response of external flow to plasma forcing is delayed for up to tens of milliseconds and the delay time increases with angle of attack increasing.Also observed is that at the intermediate angle of attack near stall,the forced flow features a well re-organized flow pattern.However,for airfoil at high post-stall angle of attack,the already well suppressed flow field can recover to the massively separated flow state and then reattach to airfoil surface with the flow pattern fluctuating between the two states in an irregular manner.This is contrary to one’s first thought that the forced flow at any angles of attack will become well organized and regular,and reflects the complexity of flow separation control.

An Adaptive Single Neural Control for Variable Step-Size P&O MPPT of Marine Current Turbine System

Marine current energy has been increasingly used because of its predictable higher power potential.Owing to the external disturbances of various flow velocity and the high nonlinear effects on the marine current turbine(MCT)system,the nonlinear controllers which rely on precise mathematical models show poor performance under a high level of parameters’uncertainties.This paper proposes an adaptive single neural control(ASNC)strategy for variable step-size perturb and observe(P&O)maximum power point tracking(MPPT)control.Firstly,to automatically update the neuron weights of SNC for the nonlinear systems,an adaptive mechanism is proposed to adaptively adjust the weighting and learning coefficients.Secondly,aiming to generate the exact reference speed for ASNC to extract the maximum power,a variable step-size law based on speed increment is designed to strike a balance between tracking speed and accuracy of P&O MPPT.The robust stability of the MCT control system is guaranteed by the Lyapunov theorem.Comparative simulation results show that this strategy has favorable adaptive performance under variable velocity conditions,and the MCT system operates at maximum power point steadily.