Design of a low power GPS receiver in 0.18 μm CMOS technology with a ΣΔ fractional-N synthesizer

A 19 mW highly integrated GPS receiver with a ΣΔ fractional-N synthesizer is presented in this paper.Fractional-N frequency synthesizer architecture was adopted in this work, to provide more degrees of freedom in the synthesizer design.A high linearity low noise amplifier(LNA) is integrated into the chip.The radio receiver chip was fabricated in a 0.18 μm complementary metal oxide semiconductor(CMOS) process and packaged in a 48-pin 2 mm×2 mm land grid array chip scale package.The chip consumes 19 mW(LNA1 excluded) and the LNA1 6.3 mW.Measured performances are:noise figure<2 dB, channel gain=108 dB(LNA1 included), image rejection>36 dB, and-108 dBc/Hz @ 1 MHz phase noise offset from the carrier.The carrier noise ratio(C/N) can reach 41 dB at an input power of-130 dBm.The chip operates over a temperature range of-40, 120 °C and ±5% tolerance over the CMOS technology process.

Design of a dual-channel multi-mode GNSS receiver with a∑△ fractional-N synthesizer

A 72 mW highly integrated dual-channel multimode GNSS（global navigation satellite system） receiver with aΣ△fractional-N synthesizer which covers GPS L1 and the Compass B1/B2/B3 band is presented.This chip was fabricated in a TSMC CMOS 0.18μm process and packaged in a 48-pin 3×3 mm^2 land grid array chip scale package.This work achieves NF≤5.3 dB without an external LNA,channel gain = 105 dB for channel one （Compass B2 and B3 band）,and channel gain = 110 dB for channel two（GPS L1 and Compass B1 band）.Image rejection（IMRR） = 36 dB,phase noise is -115.9 dBc @ 1 MHz and -108.9 dBc @ 1 MHz offset from the carrier for the two channels separately.At the low power consumption,multibands of GNSS are compatible in one chip, which is easy for consumers to use,when two different navigation signals are received simultaneously.

A Novel Method to Compensate the Sigma-Delta Shaped Noise for Wide Band Fractional-N Frequency Synthesizers

A novel method to partially compensate sigma-delta shaped noise is proposed. By injecting the compensation current into the passive loop filter during the delay time of the phase frequency detector（PFD）,a maximum reduction of the phase noise by about 16dB can be achieved. Compared to other compensation methods,the technique proposed here is relatively simple and easy to implement. Key building blocks for realizing the noise cancellation,including the delay variable PFD and compensation current source, are specially designed. Both the behavior level and circuit level simulation results are presented.

A Σ-Δ Fractional-N PLL Frequency Synthesizer with AFC for SRD Applications

A fractional-N frequency synthesizer for 433/868MHz SRD applications is implemented in a 0.3μm CMOS process. A wide-band VCO and an AFC are used to cover the desired bands. A 3bit third order sigma-delta modulator is adopted to reduce the out-band phase noise. The measurements show a VCO tuning range from 1.31 to 1.88GHz with AFC working correctly,an out-band phase noise of -139dBc/Hz at 3MHz offset frequency, and a fractional spur of less than - 60dBc. The chip area is 1.5mm × 1.2mm and the total current dissipation including LO buffers is 19mA from a single 3.0V supply voltage.

A 8.75-11.2-GHz,low phase noise fractional-N synthesizer for 802.11a/b/g zero-IF transceiver

An ultra broadband fractional-N frequency synthesizer for 802.11a/b/g zero-IF transceiver application is presented.The mathematical models for the behavior of the synthesizer＇s spur and phase noise are analyzed,and the optimization methodology is proposed.Measurement results exhibits that the frequency synthesizer＇s integrated phase noise is less than 1°（1 kHz to 100 MHz）with a 4.375 GHz carrier（after divide-by-2）,and the reference frequency spur is below-60 dBc operating with a 33 MHz reference clock.The frequency synthesizer is fabricated on a standard 0.13μm RF CMOS process and consumes 39.6 mW from a 1.2 V supply voltage.

COMPARISON OF SIGMA-DELTA MODULATOR FOR FRACTIONAL-N PLL FREQUENCY SYNTHESIZER

This paper investigates the design of digital Sigma-Delta Modulator (SDM) for fractional-N frequency synthesizer. Characteristics of SDMs are compared through theory analysis and simulation. The curve of maximum-loop-bandwidth vs. maximum-phase-noise is suggested to be a new criterion to the performance of SDM,which greatly helps designers to select an appropriate SDM structure to meet their real application requirements and to reduce the cost as low as possible. A low-spur 3-order Mul-tistage Noise Shaping (MASH)-1-1-1 SDM using three 2-bit first-order cascaded modulators is proposed,which balances the requirements of tone-free and maximum operation frequency.

A 900 MHz fractional-N synthesizer for UHF transceiver in 0.18μm CMOS technology

A 900 MHz fractional-N synthesizer is designed for the UHF transceiver. The VCO with a 4 bits capacitor bank covers 823–1061 MHz that implements 16（2^4）sub-bands. A 7/8 dual-modulus prescaler is implemented with a phase-switching circuit and high-speed flip–flops, which are composed of source coupled logic. The proposed synthesizer phase-locked loop is demonstrated with a 50 k Hz band width by a low 12.95 MHz reference clock, and offers a better phase noise and band width tradeoff. To reduce the out-band phase noise, a 4-levels 3-order single-loop sigma–delta modulator is applied. When its relative frequency resolution is settled to 10^-6, the testing results show that the phase noises are –120.6 dBc/Hz at 1 MHz and –95.0 dBc/Hz at 100 k Hz. The chip is2.1 mm^2 in UMC 0.18μm CMOS. The power is 36 m W at a 1.8 V supply.

Fast Switching Fractional-N Frequency Synthesizer Architecture Using TDTL

This paper presents an efficient indirect fractional frequency synthesizer architecture based on the time delay digital tanlock loop. The indirect type frequency synthesis systems incorporate a low complexity high performance adaptation mechanism that enables them to remain in a locked state following the division process. The performance of the proposed fractional-N synthesizer under various input conditions is demonstrated. This includes sudden changes in the system input frequency as well as the injection of noise. The results of the extensive set of tests indicate that the fractional-N synthesizer, proposed in this work, performs well and is capable of achieving frequency divisions with fine resolution. The indirect frequency synthesizer also has a wide locking range and fast switching response. This is reflected by the system ability to regain its lock in response to relatively large variations in the input frequency within a few samples. The overall system performance shows high resilience to noise as reflected by the mean square error results.

A CMOS Low Power Fully Differential Sigma-Delta Frequency Synthesizer for 2Mb/s GMSK Modulation

A CMOS fully-differential 2.4GHz ∑-△ frequency synthesizer for Gaussian minimum shift keying （GMSK）modulation is presented. A pre-compensation fractional-N phase-locked loop（PLL）is adopted in the modulator.The transfer function of the type- Ⅱ third-order phase-locked loop is deduced,and the important parameters that affect the loop transfer function are pointed out. Methods to calibrate the important loop parameters arc introduced. A differential tuned LC-VCO and a fully-differential charge pump are adopted in the PLL design. The designed circuits are simulated in a 0.18gm 1P6M CMOS process. The power consumption of the PLL is only about llmW with the low power consideration in building blocks design, and the data rate of the modulator can reach 2Mb/s.

Design of Down Scalers in Mixed-Signal GHz Frequency Synthesizer

An optimized method is presented to design the down scalers in a GHz frequency synthesizer. The down scalers are comprised of dual modulus prescaler （DMP） and programmable ＆ pulse swallow divider,different methods of high frequency analog circuit and digital logical synthesis are adopted respectively. Using a DMP high speed, lower jitter and lower power dissipation are obtained,and output frequency of 133.0MHz of the DMP working at divide-by-8 shows an RMS jitter less than 2ps. The flexibility and reusability of the progrs, mmable divider is high;its use could be extended to many complicated frequency synthesizers. By comparison,it is a better design on performance of high-frequency circuit and good design flexibility.

A 2.4GHz Quadrature Output Frequency Synthesizer

A design and implementation for a 2.4GHz quadrature output frequency synthesizer intended for bluetooth in 0. 35μm CMOS technology are presented. A differentially controlled quadrature voltage-controlled oscillator （QVCO） is employed to generate quadrature （I/Q） signals. A second-order loop filter, with a unit gain transconductance amplifier having the performance of a third-order loop filter,is exploited for low cost. The measured spot phase noise is -106.15dBc/Hz@ 1MHz. Close-in phase noise is less than -70dBc/Hz. The synthesizer consumes 13.5mA under a 3.3V voltage supply. The core size is 1.3mm×0. 8mm.

A CMOS Fully Integrated Frequency Synthesizer with Stability Compensation

A complete closed-loop third order s-domain model is analyzed for a frequency synthesizer. Based on the model and root-locus technique, the procedure for parameters design is described, and the relationship between the process,voltage,and temperature variation of parameters and the loop stability is quantitatively analyzed. A variation margin is proposed for stability compensation. Furthermore,a simple adjustable current cell in the charge pump is proposed for additional stability compensation and a novel VCO with linear gain is adopted to limit the total variation. A fully integrated frequency synthesizer from 1 to 1.05GHz with 250kHz channel resolution is implemented to verify the methods.

Frequency synthesizer for DRM/DAB/AM/FM RF front-end

This paper describes a wideband low phase noise frequency synthesizer.It operates in the multi-band including digital radio mondiale DRM digital audio broadcasting DAB amplitude modulation AM and frequency modulation FM .In order to cover the signals of the overall frequencies a novel frequency planning and a new structure are proposed. A wide-band low-phase-noise low-power voltage-control oscillator VCO and a high speed wide band high frequency division ratio pulse swallow frequency divider with a low power consumption are presented.The monolithic DRM/DAB/AM/FM frequency synthesizer chip is also fabricated in a SMIC＇s 0.18-μm CMOS process.The die area is 1 425 μm ×795 μm including the test buffer and pads. The measured results show that the VCO operating frequency range is from 2.22 to 3.57 GHz the measured phase noise of the VCO is 120.22 dBc/Hz at 1 MHz offset the pulse swallow frequency divider operation frequency is from 0.9 to 3.4 GHz.The phase noise in the phase-locked loop PLL is-59.52 dBc/Hz at 10 kHz offset and fits for the demand of the DRM/DAB/AM/FM RF front-end. The proposed frequency synthesizer consumes 47 mW including test buffer under a 1.8 V supply.

Key technologies of frequency-hopping frequency synthesizer for Bluetooth RF front-end

A scheme of a frequency-hopping frequency-synthesizer applied to a Bluetooth ratio frequency （RF） front-end is presented,and design of a voltage controlled oscillator （VCO） and dual-modulus prescaler are focused on.It is fabricated in a 0.18 μm mixed-signal CMOS （complementary metal-oxide-semiconductor transistor） process.The power dissipation of VCO is low and a stable performance is gained.The measured phase noise of VCO at 2.4 GHz is less than -114.32 dBc/Hz.The structure of the DMP is optimized and a novel D-latch integrated with ＂OR＂ logic gate is used.The measured results show that the chip can work well under a 1.8 V power supply.The power dissipation of the core part in a dual modulus prescaler is only 5.76 mW.An RMS jitter of 2 ps is measured on the output signal at 118.3 MHz.It is less than 0.02% of the clock period.

A wideband low-phase-noise LC VCO for DRM/DAB frequency synthesizer

The wideband CMOS voltage-controlled oscillator（VCO）with low phase noise and low power consumption is presented for a DRM/DAB（digital radio mondiale and digital audio broadcasting）frequency synthesizer.In order to obtain a wide band and a large tuning range,a parallel switched capacitor bank is added in the LC tank.The proposed VCO is implemented in SMIC 0.18-μm RF CMOS technology and the chip area is 750 μm×560 μm,including the test buffer circuit and the pads.Measured results show that the tuning range is 44.6%;i.e.,the frequency turning range is from 2.27 to 3.57 GHz.The measured phase noise is-122.22 dBc/Hz at a 1 MHz offset from the carrier.The maximum power consumption of the core part is 6.16 mW at a 1.8 V power supply.

Digital Coarse Tuning Loop for Wide-Band Fast-Settling Dual-Loop Frequency Synthesizers

A new coarse tuning loop for a wide-band dual-loop frequency synthesizer is presented. The coarse tuning structure is composed of two digital modules, including a successive approximation register and a frequency comparator with a novel structure. The frequency comparator counts the prescaler cycles within a certain reference time and compares the number with preset data to estimate the VCO frequency. The frequency comparison error is analyzed in detail. Within a given coarse tuning time,our proposed structure shows a comparison error 20 times smaller than that of other reported structures. This structure also reuses the programmable divider as a part of the coarse tuning loop so that the circuit is greatly simplified.

Analysis and Design of a ΔΣ Modulator for Fractional-N Frequency Synthesis

This paper presents the design considerations and implementation of a novel topology digital multistage-noise-shaping （MASH） delta-sigma modulator suitable for fractional-N phase-locked-loop （PLL） frequency synthesis. In an effort to reduce the complexity and dissipation,a pipeline technique has been used, and the proposed carry save tree （CST） algorithm optimizes the multi-input adder structure. The circuit has been verified through Matlab simulation, ASIC implementation, and FPGA experiment, which exhibits high performance and potential for a gigahertz range,low-power monolithic CMOS frequency synthesizer.

A 1-GHz Charge Pump PLL Frequency Synthesizer for IEEE 1394b PHY

The design procedure of an 1-GHz phase-locked loop （PLL）-based frequency synthesizer used in IEEE 1394b physical （PHY） system is presented in this paper. The PLL＇s loop dynamics are analyzed in depth and theoretical relationships between all loop parameters are clearly described. All the parameters are derived and verified by Verilog-A model, which ensures the accuracy and efficiency of the circuit design and simulation. A 4-stage ring oscillator is employed to generate 1-GHz oscillation frequency and is divided into low frequency clocks by a feedback divider. The architecture is a third-order, type-2 charge pump PLL. The simulated settling time is less than 4μs. The RMS value of period jitter of the PLL＇s output is 2.1 ps. The PLL core occupies an area of 0.12 mm2, one fourth of which is occupied by the MiM loop capacitors. The total current consumption of the chip is 16.5 mA. The chip has been sent for fabrication in 0.13 μm complementary metal oxide semiconductor （CMOS） technology.

BIT COMMITMENT USING PSEUDO-RANDOM SYNTHESIZER

This paper presents two practical message commitment schemes: one is suitable for committing many bits, and another is useful for committing any bit-long message. They are provably secure based on pseudo-random synthesizers. In these schemes, the sender may be unbounded to polynomial time and the receiver is bounded. The advantage of these schemes is that the secure parameter may be small.

Frequency Synthesizer of Short-Wave SFH/MFSK System

The technology of DDS-driven PLL is introduced and a new scheme of frequency synthesizer which is suitable for SW SFH/MFSK System is presented in this paper. Based on the special requirement of SW communication, a model of the scheme is given and the results show that the frequency synthesizer has small frequency insteval (≤0.1 Hz), short switch pierod (<200 ms) and high frequency stability as crystal oseillator.