Influences of clean fracturing fluid viscosity and horizontal in-situ stress difference on hydraulic fracture propagation and morphology in coal seam

The viscosity of fracturing fluid and in-situ stress difference are the two important factors that affect the hydraulic fracturing pressure and propagation morphology. In this study, raw coal was used to prepare coal samples for experiments, and clean fracturing fluid samples were prepared using CTAB surfactant. A series of hydraulic fracturing tests were conducted with an in-house developed triaxial hydraulic fracturing simulator and the fracturing process was monitored with an acoustic emission instrument to analyze the influences of fracturing fluid viscosity and horizontal in-situ stress difference on coal fracture propagation. The results show that the number of branched fractures decreased, the fracture pattern became simpler, the fractures width increased obviously, and the distribution of AE event points was concentrated with the increase of the fracturing fluid viscosity or the horizontal in-situ stress difference. The acoustic emission energy decreases with the increase of fracturing fluid viscosity and increases with the increase of horizontal in situ stress difference. The low viscosity clean fracturing fluid has strong elasticity and is easy to be compressed into the tip of fractures, resulting in complex fractures. The high viscosity clean fracturing fluids are the opposite. Our experimental results provide a reference and scientific basis for the design and optimization of field hydraulic fracturing parameters.

Optimization method of fracturing fluid volume intensity for SRV fracturing technique in shale oil reservoir based on forced imbibition:A case study of well X-1 in Biyang Sag of Nanxiang Basin,China

An optimization method of fracturing fluid volume strength was introduced taking well X-1 in Biyang Sag of Nanxiang Basin as an example.The characteristic curves of capillary pressure and relative permeability were obtained from history matching between forced imbibition experimental data and core-scale reservoir simulation results and taken into a large scale reservoir model to mimic the forced imbibition behavior during the well shut-in period after fracturing.The optimization of the stimulated reservoir volume(SRV)fracturing fluid volume strength should meet the requirements of estimated ultimate recovery(EUR),increased oil recovery by forced imbibition and enhancement of formation pressure and the fluid volume strength of fracturing fluid should be controlled around a critical value to avoid either insufficiency of imbibition displacement caused by insufficient fluid amount or increase of costs and potential formation damage caused by excessive fluid amount.Reservoir simulation results showed that SRV fracturing fluid volume strength positively correlated with single-well EUR and an optimal fluid volume strength existed,above which the single-well EUR increase rate kept decreasing.An optimized increase of SRV fracturing fluid volume and shut-in time would effectively increase the formation pressure and enhance well production.Field test results of well X-1 proved the practicality of established optimization method of SRV fracturing fluid volume strength on significant enhancement of shale oil well production.

Supramolecular polymer-based gel fracturing fluid with a double network applied in ultra-deep hydraulic fracturing

A gel based on polyacrylamide,exhibiting delayed crosslinking characteristics,emerges as the preferred solution for mitigating degradation under conditions of high temperature and extended shear in ultralong wellbores.High viscosity/viscoelasticity of the fracturing fluid was required to maintain excellent proppant suspension properties before gelling.Taking into account both the cost and the potential damage to reservoirs,polymers with lower concentrations and molecular weights are generally preferred.In this work,the supramolecular action was integrated into the polymer,resulting in significant increases in the viscosity and viscoelasticity of the synthesized supramolecular polymer system.The double network gel,which is formed by the combination of the supramolecular polymer system and a small quantity of Zr-crosslinker,effectively resists temperature while minimizing permeability damage to the reservoir.The results indicate that the supramolecular polymer system with a molecular weight of(268—380)×10^(4)g/mol can achieve the same viscosity and viscoelasticity at 0.4 wt%due to the supramolecular interaction between polymers,compared to the 0.6 wt%traditional polymer(hydrolyzed polyacrylamide,molecular weight of 1078×10^(4)g/mol).The supramolecular polymer system possessed excellent proppant suspension properties with a 0.55 cm/min sedimentation rate at 0.4 wt%,whereas the0.6 wt%traditional polymer had a rate of 0.57 cm/min.In comparison to the traditional gel with a Zrcrosslinker concentration of 0.6 wt%and an elastic modulus of 7.77 Pa,the double network gel with a higher elastic modulus(9.00 Pa)could be formed only at 0.1 wt%Zr-crosslinker,which greatly reduced the amount of residue of the fluid after gel-breaking.The viscosity of the double network gel was66 m Pa s after 2 h shearing,whereas the traditional gel only reached 27 m Pa s.

A Novel Fracturing Fluid with High-Temperature Resistance for Ultra-Deep Reservoirs

Ultra-deep reservoirs play an important role at present in fossil energy exploitation.Due to the related high temperature,high pressure,and high formation fracture pressure,however,methods for oil well stimulation do not produce satisfactory results when conventional fracturing fluids with a low pumping rate are used.In response to the above problem,a fracturing fluid with a density of 1.2~1.4 g/cm^(3)was developed by using Potassium formatted,hydroxypropyl guanidine gum and zirconium crosslinking agents.The fracturing fluid was tested and its ability to maintain a viscosity of 100 mPa.s over more than 60 min was verified under a shear rate of 1701/s and at a temperature of 175℃.This fluid has good sand-carrying performances,a low viscosity after breaking the rubber,and the residue content is less than 200 mg/L.Compared with ordinary reconstruction fluid,it can increase the density by 30%~40%and reduce the wellhead pressure of 8000 m level reconstruction wells.Moreover,the new fracturing fluid can significantly mitigate safety risks.

Research on the Performance of New Weighted Slippery Water Fracturing Fluid System

Deep and ultra-deep reservoirs have dense matrix and high fracture pressure, which leads to high pressure and difficulty in fracturing construction. Conventional aggravated fracturing fluids have the problems of low aggravation efficiency, high friction resistance, etc., and the reduction of construction pressure cannot reach the theoretical effect. In view of the above problems, this paper adopts the weighting agent HD160 and the drag reducing agent JHFR-2 to form a new type of weighted slippery water fracturing fluid system. And the weighting performance, drag reduction performance, corrosion performance, anti-expansion performance and reservoir damage of this system were studied. The results show that the density of the system is adjustable within 1.1 - 1.6 g·cm−3, and the drag reduction rate can be up to 68% at 1.5 g·cm−3, with low corrosion rate, surface tension less than 28 mN·m−1, anti-expansion rate as high as 94.5%, and the damage rate of the reservoir permeability is less than 10%, which is of good application prospect.

Microscopic characteristics of tight sandstone reservoirs and their effects on the imbibition efficiency of fracturing fluids:A case study of the Linxing area,Ordos Basin

The Linxing area within the Ordos Basin exhibits pronounced reservoir heterogeneity and intricate micro-pore structures,rendering it susceptible to water-blocking damage during imbibition extraction.This study delved into the traits of tight sandstone reservoirs in the 8th member of the Shihezi Formation(also referred to as the He 8 Member)in the study area,as well as their effects on fracturing fluid imbibition.Utilizing experimental techniques such as nuclear magnetic resonance(NMR),high-pressure mercury intrusion(HPMI),and gas adsorption,this study elucidated the reservoir characteristics and examined the factors affecting the imbibition through imbibition experiments.The findings reveal that:①The reservoir,with average porosity of 8.40%and average permeability of 0.642×10^(-3)μm^(2),consists principally of quartz,feldspar,and lithic fragments,with feldspathic litharenite serving as the primary rock type and illite as the chief clay mineral;②Nano-scale micro-pores and throats dominate the reservoir,with dissolution pores and intercrystalline pores serving as predominant pore types,exhibiting relatively high pore connectivity;③Imbibition efficiency is influenced by petrophysical properties,clay mineral content,and microscopic pore structure.Due to the heterogeneity of the tight sandstone reservoir,microscopic factors have a more significant impact on the imbibition efficiency of fracturing fluids;④A comparative analysis shows that average pore size correlates most strongly with imbibition efficiency,followed by petrophysical properties and clay mineral content.In contrast,the pore type has minimal impact.Micropores are vital in the imbibition process,while meso-pores and macro-pores offer primary spaces for imbibition.This study offers theoretical insights and guidance for enhancing the post-fracturing production of tight sandstone reservoirs by examining the effects of these factors on the imbibition efficiency of fracturing fluids in tight sandstones.

Formation damage mechanism and control strategy of the compound function of drilling fluid and fracturing fluid in shale reservoirs

For the analysis of the formation damage caused by the compound function of drilling fluid and fracturing fluid,the prediction method for dynamic invasion depth of drilling fluid is developed considering the fracture extension due to shale minerals erosion by oil-based drilling fluid.With the evaluation for the damage of natural and hydraulic fractures caused by mechanical properties weakening of shale fracture surface,fracture closure and rock powder blocking,the formation damage pattern is proposed with consideration of the compound effect of drilling fluid and fracturing fluid.The formation damage mechanism during drilling and completion process in shale reservoir is revealed,and the protection measures are raised.The drilling fluid can deeply invade into the shale formation through natural and induced fractures,erode shale minerals and weaken the mechanical properties of shale during the drilling process.In the process of hydraulic fracturing,the compound effect of drilling fluid and fracturing fluid further weakens the mechanical properties of shale,results in fracture closure and rock powder shedding,and thus induces stress-sensitive damage and solid blocking damage of natural/hydraulic fractures.The damage can yield significant conductivity decrease of fractures,and restrict the high and stable production of shale oil and gas wells.The measures of anti-collapse and anti-blocking to accelerate the drilling of reservoir section,forming chemical membrane to prevent the weakening of the mechanical properties of shale fracture surface,strengthening the plugging of shale fracture and reducing the invasion range of drilling fluid,optimizing fracturing fluid system to protect fracture conductivity are put forward for reservoir protection.

Insights into in-situ imbibition behavior of fracturing fluid in propped shale fractures based on nuclear magnetic resonance:A case study from Longmaxi Formation shale,Sichuan Basin,China

Shale gas is an important component of unconventional oil and gas resources.Studying the imbibition behavior is helpful to optimize flowback parameters and enhance gas recovery.Recent imbibition studies have focused on shale matrix,and the pressure conditions discussed were mostly atmospheric.The initial imbibition behavior begins from propped fractures to matrix,but there are few studies working on explaining the imbibition behavior in propped fractures or the phenomenon of many shale wells exhibit higher productivity after a“soaking”period.Therefore,propped fracture samples were designed for imbibition and migration experiments.In order to accurately study the mechanism and main influencing factors of fracturing fluid imbibition and migration in propped and unpropped shale fractures under high temperature and high pressure,a series of experiments based on nuclear magnetic resonance(NMR)were carried out.Results showed that NMR T_(2) spectra of all samples exhibited a bimodal distribution.The final imbibition volume of fracturing fluid was positively related to pressure and fracture width.The imbibition effect of fracturing fluid was more evident in matrix pores under high pressure.In the migration during soaking stage,the fracturing fluid gradually migrated from large pores to small pores and gradually displaced the shale gas from the matrix,thus allowing the water blocking in propped fractures to self-unlock to some extent.Gas permeability decreased in the imbibition stage,while it recovered in the migration stage to some extent.

The enhancement of performance and imbibition effect of slickwater-based fracturing fluid by using MoS_(2)nanosheets

Slickwater-based fracturing fluid has recently garnered significant attention as the major fluid for volumetric fracturing;however,lots of challenges and limitations such as low viscosity,poor salt tolerance,and possible formation damage hinder the application of the conventional simple slickwater-based fracturing fluid.In addition,nanomaterials have proven to be potential solutions or improvements to a number of challenges associated with the slickwater.In this paper,molybdenum disulfide(MoS_(2))nanosheets were chemically synthesized by hydrothermal method and applied to improve the performance of conventional slickwater-based fracturing fluid.Firstly,the microstructure characteristics and crystal type of the MoS_(2)nanosheets were analyzed by SEM,EDS,TEM,XPS,and Raman spectroscopy techniques.Then,a series of evaluation experiments were carried out to compare the performance of MoS_(2)nanosheet-modified slickwater with the conventional slickwater,including rheology,drag reduction,and sand suspension.Finally,the enhanced imbibition capacity and potential mechanism of the nanosheet-modified slickwater were systematically investigated.The results showed that the self-synthesized MoS_(2)nanosheets displayed a distinct ultrathin flake-like morphology and a lateral size in the range of tens of nanometers.In the nano-composites,each MoS_(2)nanosheet plays the role of cross-linking point,so as to make the spatial structure of the entire system more compact.Moreover,nanosheet-modified slickwater demonstrates more excellent properties in rheology,drag reduction,and sand suspension.The nanosheet-modified slickwater has a higher apparent viscosity after shearing 120 min under 90℃ and 170 s^(−1).The maximum drag reduction rate achieved 76.3%at 20℃,and the sand settling time of proppants with different mesh in the nano-composites was prolonged.Spontaneous imbibition experiments showed that the gel-breaking fluid of nanosheet-modified slickwater exhibited excellent capability of oil-detaching,and increase the oil recovery to∼35.43%.By observing and analyzing the interfacial behavior of MoS_(2)nanosheets under stimulated reservoir conditions,it was found that the presence of an interfacial tension gradient and the formation of a climbing film may play an essential role in the spontaneous imbibition mechanism.This work innovatively uses two-dimensional MoS_(2)nanosheets to modify regular slickwater and confirms the feasibility of flake-like nanomaterials to improve the performance of slickwater.The study also reveals the underlying mechanism of enhanced imbibition efficiency of the nano-composites.

Intermolecular interactions induced property improvement for clean fracturing fluid by deep eutectic solvents

Fracturing fluid property play a critical role in developing unconventional reservoirs.Deep eutectic solvents(DESs)show fascinating potential for property improvement of clean fracturing fluids(CFFs)due to their low-price,low-toxicity,chemical stability and flexible designability.In this work,DESs were synthesized by mixing hydrogen bond acceptors(HBAs)and a given hydrogen bond donor(HBD)to explore their underlying influence on CFF properties based on the intermolecular interactions.The hydrogen-bonding,van der Waals and electrostatic interactions between DES components and surfactants improved the CFF properties by promoting the arrangement of surfactants at interface and enhancing the micelle network strength.The HBD enhanced the resistance of CFF for Ca^(2+) due to coordination-bonding interaction.The DESs composed of choline chloride(ChCl)and malonic acid show great enhancement for surface,rheology,temperature resistance,salt tolerance,drag reduction,and gel-breaking performance of CFFs.The DESs also improved the gel-breaking CFF-oil interactions,increasing the imbibition efficiencies to 44.2%in 74 h.Adjusting HBAs can effectively strengthen the intermolecular interactions(e.g.,HBA-surfactant and HBD-surfactant interactions)to improve CFF properties.The DESs developed in this study provide a novel strategy to intensify CFF properties.

Temporal variations in geochemistry of hydraulic fracturing fluid and flowback water in a tight oil reservoir

Hydraulic fracturing facilitates the development and exploitation of unconventional reservoirs.In this study,the injected hydraulic fracturing fluid(HFF)and flowback and produced water(FPW)in tight oil reservoirs of the Lucaogou Formation in the Junggar Basin are temporally sampled from day 1 to day 64.Freshwater is used for fracturing,and HFF is obtained.The chemical and isotopic parameters(including the water type,total salinity,total dissolved solids(TDS),pH,concentrations of Na^(+),Cl^(-),Ba^(+),K^(+),Fe^(2+)+Fe^(3+),and CO_(3)^(2-),dD,and δ^(18)O)are experimentally obtained,and their variations with time are systematically analyzed based on the flowback water.The results show that the water type,Na/Cl ratio,total salinity,and TDS of the FPW change periodically primarily due to the HFF mixing with formation water,thus causing δD and δ^(18)O to deviate from the meteoric water line of Xinjiang.Because of watererock interaction(WRI),the concentrations of Fe^(2+)+Fe^(3+)and CO_(3)^(2-)of the FPW increase over time,with the solution pH becoming more alkaline.Furthermore,based on the significant changes observed in the geochemistry of the FPW,three separate time intervals of flowback time are identified:Stage Ⅰ(<10 days),where the FPW is dominated by the HFF and the changes in ions and isotopes are mainly caused by the WRI;Stage Ⅱ(10-37 days),where the FPW is dominated by the addition of formation water to the HFF and the WRI is weakened;and finally,Stage Ⅲ(>37 days),where the FPW is dominated by the chemistry of the formation water.The methodology implemented in this study can provide critical support for the source identification of formation water.

Probing the influence of secondary fracture connectivity on fracturing fluid flowback efficiency

A deep understanding of the geometric impacts of fracture on fracturing fluid flowback efficiency is essential for unconventional oil development. Using nuclear magnetic resonance and 2.5-dimensional matrix-fracture visualization microfluidic models, qualitative and quantitative descriptions of the influences of connectivity between primary fracture and secondary fracture on flowback were given from core scale to pore network scale. The flow patterns of oil-gel breaking fluid two-phase flow during flowback under different fracture connectivity were analyzed. We found some counterintuitive results that non-connected secondary fracture (NCSF, not connect with artificial primary fracture and embedded in the matrix) is detrimental to flowbackefficiency. The NCSF accelerates the formation of oil channeling during flowback, resulting in a large amount of fracturing fluid trapped in the matrix, which is not beneficial for flowback. Whereas the connected secondary fracture (CSF, connected with the artificial primary fracture) is conducive to flowback. The walls of CSF become part of primary fracture, which expands the drainage area with low resistance, and delays the formation of the oil flow channel. Thus, CSF increases the high-speed flowback stage duration, thereby enhancing the flowback efficiency. The fracturing fluid flowback efficiency investigated here follows the sequence of the connected secondary fracture model (72%) > the matrix model (66%) > the non-connected secondary fracture model (38%). Our results contribute to hydraulic fracturing design and the prediction of flowback efficiency.

Preparation of a functional fracturing fluid with temperature-and salt-resistance,and low damage using a double crosslinking network

Fracturing fluids(FFs)have been widely used to stimulate the tight reservoir.However,current FFs will not only lose their rheological property at high temperatures and high salt but also show an incomplete gel-breaking property.Herein,a double crosslinking network FF with pretty superiorities in rheology and low damage to the core was constructed by introducing both physical crosslinking and chemical crosslinking into the system.The construction of double crosslinking networks enhanced the rheology of this functional FF.The particle sizes of gel-breaking fluids are mainly distributed in 1.0e10,000 nm;furthermore,for every 10,000 mg/L increase in salinity,the particle size of the gel-breaking fluid is decreased by almost half.The adsorption capacity(<1.0 mg/g)gradually decreased with the increase of salinity at 20℃.Moreover,the adsorption of gel-breaking fluids on the rock decreased first and then kept stable with temperature increasing at a salinity of ≤30,000 mg/L,however,showed the opposite trend at 40,000 mg/L.The results of rheology,particle size,static adsorption,and core damage showed that this functional FF could be an alternative for the stimulation of a tight reservoir with high temperature and recycling of produced water with high salinity.

Experimental study on the adverse effect of gel fracturing fluid on gas sorption behavior for Illinois coal

Hydraulic fracturing is an effective technology for coal reservoir stimulation.After fracturing operation and flowback,a fraction of fracturing fluid will be essentially remained in the formation which ultimately damages the flowability of the formation.In this study,we quantified the gel-based fracturing fluid induced damages on gas sorption for Illinois coal in US.We conducted the high-pressure methane and CO_(2)sorption experiments to investigate the sorption damage due to the gel residue.The infrared spectroscopy tests were used to analyze the evolution of the functional group of the coal during fracturing fluid treatment.The results show that there is no significant chemical reaction between the fracturing fluid and coal,and the damage of sorption is attributed to the physical blockage and interactions.As the concentration of fracturing fluid increases,the density of residues on the coal surface increases and the adhesion film becomes progressively denser.The adhesion film on coal can apparently reduce the number of adsorption sites for gas and lead to a decrease of gas sorption capacity.In addition,the gel residue can decrease the interconnectivity of pore structure of coal which can also limit the sorption capacity by isolating the gas from the potential sorption sites.For the low concentration of fracturing fluid,the Langmuir volume was reduced to less than one-half of that of raw coal.After the fracturing fluid invades,the desorption hysteresis of methane and CO_(2)in coal was found to be amplified.The impact on the methane desorption hysteresis is significantly higher than CO_(2)does.The reason for the increasing of hysteresis may be that the adsorption swelling caused by the residue adhered on the pore edge,or the pore blockage caused by the residue invasion under high gas pressure.The results of this study quantitatively confirm the fracturing fluid induced gas sorption damage on coal and provide a baseline assessment for coal fracturing fluid formulation and technology.

Fracturing timing of Jurassic reservoirs in the Dibei-Tuziluoke gas field,Kuqa foreland basin:Evidence from petrography,fluid inclusions,and clumped isotopes

Determining the timing of fracturing is crucial for understanding reservoir evolution and hydrocarbon accumulation in foreland basins.Using fracturing data from cores,borehole images,and outcrops,combined with the clumped isotope(D47)and fluid inclusion analyses of carbonate minerals filled in pores and fractures,this study ascertained the fracturing timing of the Jurassic reservoirs in the Dibei-Tuziluoke Gas Field,Kuqa Foreland Basin.Data from outcrops and borehole images show two dominant fracture sets in the study area:W-E and NE-SW striking fractures.Some W-E striking fractures are carbonate-filled,while NE-SW striking fractures lack mineral fillings.Bitumen veins,not easy to be identified in borehole images,are prevalent in cores.The petrographic analysis reveals that these bitumen veins formed before the calcite cementation in pores and display high viscosity and low maturity.Homogenization temperatures(T_(h))from primary fluid inclusion assemblages in two representative calcite vein samples were notably lower than T_(△47) values from corresponding samples.This suggests the △_(47) signature underwent alteration due to partial reordering during burial.Thus,△_(47)-derived temperatures(apparent temperatures)may not faithfully represent the mineral precipitation temperatures.When plotting these apparent temperatures vs.the burial history,only the possible latest ages of fracturing emerged.These ages were further refined by considering petroleum charging,tectonic evolution,and stress orientation.Bitumen-filled fractures likely resulted from the Late Cretaceous uplift,marking the migration of low-maturity hydrocarbons in the study area.Carbonate-filled E-W striking fractures emerged during the late Miocene(~13-6.5 Ma)alongside fold development.NE-striking fractures that crosscut W-E ones possibly formed recently due to stress reorientation.

Experimental investigation of shale imbibition capacity and the factors influencing loss of hydraulic fracturing fluids

Spontaneous imbibition of water-based frac- turing fluids into the shale matrix is considered to be the main mechanism responsible for the high volume of water loss during the flowback period. Understanding the matrix imbibition capacity and rate helps to determine the frac- turing fluid volume, optimize the flowback design, and to analyze the influences on the production of shale gas. Imbibition experiments were conducted on shale samples from the Sichuan Basin, and some tight sandstone samples from the Ordos Basin. Tight volcanic samples from the Songliao Basin were also investigated for comparison. The effects of porosity, clay minerals, surfactants, and KC1 solutions on the matrix imbibition capacity and rate were systematically investigated. The results show that the imbibition characteristic of tight rocks can be characterized by the imbibition curve shape, the imbibition capacity, the imbibition rate, and the diffusion rate. The driving forces of water imbibition are the capillary pressure and the clay absorption force. For the tight rocks with low clay contents, the imbibition capacity and rate are positively correlated with the porosity. For tight rocks with high clay content, the type and content of clay minerals are the most impor- tant factors affecting the imbibition capacity. The imbibed water volume normalized by the porosity increases with an increasing total clay content. Smectite and illite/smectite tend to greatly enhance the water imbibition capacity. Furthermore, clay-rich tight rocks can imbibe a volume of water greater than their measured pore volume. The aver- age ratio of the imbibed water volume to the pore volume is approximately 1.1 in the Niutitang shale, 1.9 in the Lujiaping shale, 2.8 in the Longmaxi shale, and 4.0 in the Yingcheng volcanic rock, and this ratio can be regarded as a parameter that indicates the influence of clay. In addition, surfactants can change the imbibition capacity due to alteration of the capillary pressure and wettability. A 10 wt% KC1 solution can inhibit clay absorption to reduce the imbibition capacity.

Investigation on microscopic invasion characteristics and retention mechanism of fracturing fluid in fractured porous media

Reservoir damage caused by guar gum fracturing fluid and slick water seriously affects the subsequent oil and gas production. However, the invasion characteristics and retention mechanisms of fracturing fluids in the fracture-matrix zone are still unclear. In this work, a microscopic model reflecting the characteristics of the fracture-matrix zone was designed. Based on the microfluidic experimental method, the process of fracturing fluid invasion, flowback and retention in the fracture-matrix zone was investigated visually and characterized quantitatively. The factors and mechanisms affecting fracturing fluid retention in the fracture-matrix zone were analyzed and clarified. The results indicated that in the invasion process, the frontal swept range of slick water was larger than that of the guar gum fracturing fluid, and the oil displacement efficiency and damage rate were lower than those of the guar gum fracturing fluid under the same invasion pressure. With the increase in invasion pressure, the damage rate of slick water increased from 61.09% to 82.77%, and that of the guar gum fracturing fluid decreased from 93.45% to83.36%. Before subsequent oil production, the invaded fracturing fluid was mainly concentrated in the medium-high permeability area of the fracture-matrix zone. The main resistance of slick water was capillary force, while that of the guar fracturing fluid was mainly viscous resistance. The fracturing fluid retention was most serious in the low permeability region and the region near the end of the fracture.The experimental and numerical simulation results showed that increasing the production pressure difference could improve the velocity field distribution of the fracture-matrix zone, increase the flowback swept range and finally reduce the retention rate of the fracture fluid. The retention mechanisms of slick water in the fracture-matrix zone include emulsion retention and flow field retention, while those of the guar gum fracturing fluid include viscous retention and flow field retention. Emulsion retention is caused by capillary force and flow interception effect. Viscous retention is caused by the viscous resistance of polymer, while flow-field retention is caused by uneven distribution of flowback velocity.

A review of reservoir damage during hydraulic fracturing of deep and ultra-deep reservoirs

Deep and ultra-deep reservoirs have gradually become the primary focus of hydrocarbon exploration as a result of a series of significant discoveries in deep hydrocarbon exploration worldwide.These reservoirs present unique challenges due to their deep burial depth(4500-8882 m),low matrix permeability,complex crustal stress conditions,high temperature and pressure(HTHP,150-200℃,105-155 MPa),coupled with high salinity of formation water.Consequently,the costs associated with their exploitation and development are exceptionally high.In deep and ultra-deep reservoirs,hydraulic fracturing is commonly used to achieve high and stable production.During hydraulic fracturing,a substantial volume of fluid is injected into the reservoir.However,statistical analysis reveals that the flowback rate is typically less than 30%,leaving the majority of the fluid trapped within the reservoir.Therefore,hydraulic fracturing in deep reservoirs not only enhances the reservoir permeability by creating artificial fractures but also damages reservoirs due to the fracturing fluids involved.The challenging“three-high”environment of a deep reservoir,characterized by high temperature,high pressure,and high salinity,exacerbates conventional forms of damage,including water sensitivity,retention of fracturing fluids,rock creep,and proppant breakage.In addition,specific damage mechanisms come into play,such as fracturing fluid decomposition at elevated temperatures and proppant diagenetic reactions at HTHP conditions.Presently,the foremost concern in deep oil and gas development lies in effectively assessing the damage inflicted on these reservoirs by hydraulic fracturing,comprehending the underlying mechanisms,and selecting appropriate solutions.It's noteworthy that the majority of existing studies on reservoir damage primarily focus on conventional reservoirs,with limited attention given to deep reservoirs and a lack of systematic summaries.In light of this,our approach entails initially summarizing the current knowledge pertaining to the types of fracturing fluids employed in deep and ultra-deep reservoirs.Subsequently,we delve into a systematic examination of the damage processes and mechanisms caused by fracturing fluids within the context of hydraulic fracturing in deep reservoirs,taking into account the unique reservoir characteristics of high temperature,high pressure,and high in-situ stress.In addition,we provide an overview of research progress related to high-temperature deep reservoir fracturing fluid and the damage of aqueous fracturing fluids to rock matrix,both artificial and natural fractures,and sand-packed fractures.We conclude by offering a summary of current research advancements and future directions,which hold significant potential for facilitating the efficient development of deep oil and gas reservoirs while effectively mitigating reservoir damage.

Adsorption damage and control measures of slick-water fracturing fluid in shale reservoirs

The slick-water polymer adsorption damage and control measures in shale were examined using a shale pack model of the Ordovician Wufeng Formation–Silurian Longmaxi Formation in the Changning block of the Sichuan Basin. The adsorption law of slick water under different displacement time, concentrations, p H values and temperatures of polymer were tested by traditional displacement experiment and UV-Vis spectrophotometer. The adsorption equilibrium time was 150 min, the amount of adsorption was proportional to the concentration of the polymer, and the maximum adsorption concentration was 1 800 mg/L. With the increase of p H value, the adsorption capacity decreased gradually, the adsorption capacity increased first and then decreased with the increase of temperature, and the adsorption capacity was the largest at 45 ?C. The adsorption patterns of polymers on shale were described by scanning electron microscopy and magnetic resonance imaging. It is proved that the adsorption of polymer on shale led to the destruction of the network structure of anionic polyacrylamide molecules, and the shale adsorption conformation was characterized qualitatively. Finally, according to the adsorption law and adsorption mechanism, it is proposed to reduce the adsorption quantity of polymer on shale surface by using hydrogen bond destruction agent. The effects of hydrogen bond destruction on four kinds of strong electronegative small molecules were compared, the hydrogen bond destroyer c was the best, which lowered the adsorption capacity by 5.49 mg/g and recovered permeability to 73.2%. The research results provide a reference for the optimization of construction parameters and the improvement of slickwater liquid system.

Laboratory Research on the Performance of Fracturing Fluid System for Unconventional Oil and Gas Reservoir Transformation

Fracturing fluid is the blood of fracturing construction, which is very important for fracturing, which requires that fracturing fluid needs to have good performance. The three commonly used fracturing fluids for unconventional oil and gas reservoir transformation are: 1) Guar gum fracturing fluid;2) Water-based emulsion slippery water fracturing fluid;3) Oil-based emulsion slippery water fracturing fluid. In this paper, water samples and other experimental data provided by Mahu Oilfield are used to evaluate three different fracturing fluid systems in laboratory. The formulas of the three different fracturing fluid systems are: 1) Water-based emulsion slippery water fracturing fluid is clean slippery water fracturing fluid 0.1% JHFR-2D drag reducer + 0.2% JHFD-2 multifunctional additive;2) Oil-based emulsion slippery water fracturing fluid 0.1% A agent + 0.2% B agent;3) Guar gum fracturing fluid 0.1% guanidine gum + 0.5% drainage aid + 0.3% demulsifier. The compatibility, drag reduction performance, reservoir damage, residue content, anti-swelling performance, surface interfacial tension, viscosity and other properties of three different slippery water fracturing fluid systems were studied. Through laboratory experiments, the comprehensive indicators show that clean slippery water fracturing fluid has obvious advantages.