Simulation of the continuous casting process in a mold of free-cutting steel 38MnVS based on a MiLE method

A new method called mixed Lagrangian and Eulerian （MiLE） method was used to simulate the continuous casting process in a mold of free-cutting steel 38MnVS.The simulation results are basically in agreement with experimental data in the literature,achieving the three-dimensional visualization of temperature distribution,melt flow,shell thickness,and stress distribution of blooms in a mold.It is shown that the flow velocity of steel melt becomes smaller gradually as the casting proceeds.When the flow reaches a certain depth,two types of flow patterns can be observed in the upper zone of the mold.The first flow pattern is to flow downwards,and the second one is to flow upwards to the meniscus.The corner temperature is higher,and the thickness is thinner than those in the mid-face.The effective stress in the corner area is much bigger than that in the mid-face,indicating that the corner area is the dangerous zone of cracking.

Experimental Study and Thermodynamical Calculation on the Formation of Eutectic Phase of MnS-RE_2S_3 and(Mn,Ca)S-RE_2S_3 in Sulfur-Containing Free-Cutting Steel

The free-cutting phase in RE or Ca-RE treated sulfur-containing free-cutting steel is the eutectic phases of MnS-RE_2S_3 and (Mn,Ca)S-RE_2S_3,respectively.The atomic ratio of RE/S needed to modify all the MnS into the eutectic phase is higher than 1.48 or 1.41-1.37 Ca/S,when RE or Ca-RE is used as the modifiz- er in the sulfur-containing free-cutting steel.Moreover,the thermodynamical calculation shows that the eutectic temperature is lower than the solidifying temperature,which is the key condition for the eutectic phase to keep globual during solidifying.

Influence of Ca/S and Rolling Reduction on Shape of Sulphide in Free-cutting Steel 5NiSCa

1.IntroductionThe shape of sulphide has a great influ-ence on machinability and transverse prop-erty of steel.It is very important to obtainoval sulphide instead of elongated one forimproving machinability and transverseproperties[1,2].

Effects of elemental Sn on the properties and inclusions of the free-cutting steel

A new environment-friendly free-cutting steel alloyed with elemental Sn （Y20Sn） was developed to meet the requirements of machinability and mechanical properties according to GB/T8731--1988. The machinability of the steel is enhanced by the segregation of elemental Sn at grain boundaries. The effect of Sn segregation on intergranular brittle fracture at normal cutting temperature from 250℃ to 400℃ is confirmed. The formation mechanism of main inclusions MnS is influenced by the presence of Sn and the attachment of Sn around MnS itself as a surfactant, and this mechanism also explains the improvement in machinability and mechanical properties of the steel. In the steel, the relevant inclusions are mainly spherical or axiolitic, and are uniformly distributed in small volume. Such inclusions improve the machinability of the steel and do not impair the mechanical properties as well. Experimental results demonstrate that the appropriate content of Sn in the steel is 0.03wt% to 0.08wt%, and the remaining composition is close to that of standard Y20 steel.

Application of fractal theory to study morphology of manganese sulfide inclusion in resulfurized free-cutting steels

The morphology and distribution of manganese sulfide(MnS)inclusions have a significant influence on the comprehensive performance,which is an important research field for resulfurized steels.Based on the experiments of non-aqueous electrolyte and scanning electron microscope observation,the fractal theory was employed to study the three-dimensional morphologies of MnS inclusions.The results showed that the edge fractal dimension of MnS inclusions was between 1.59 and 1.88.In addition,similar morphology of MnS inclusions had a close fractal dimension.The MnS edge fractal dimension is highly positively correlated with the morphological parameters.The multifractal spectrums of MnS inclusions on two-dimensional plane of as-cast and as-rolled resulfurized free-cutting steels were calculated.The large-size MnS inclusions belong to large probability subset,while the small-size MnS inclusions belong to small probability subset.The multifractal spectrum can truly and effectively reflect the difference and non-uniformity of distribution of MnS inclusions on 2D plane.On the premise of similar content of MnS,with the refinement of MnS inclusions,the multifractal spectrum width and the multifractal spectrum symmetry parameter were decreased.The multifractal spectrum provides a new method for studying the second phase in materials.

Application of tellurium in free-cutting steels

Te is widely used in iron and steel industry. After adding a certain amount of Te in the steel, many physical and chemical properties can be improved. As a free-cutting element, a small amount of Te can significantly improve the machinability of steel. The existing form of Te in the steel, the modification law of MnS inclusion by Te and the influence rule and mechanism of Te on the machinability of steel are summarized and expounded in detail, providing a reference for further study and development of Te-containing free-cutting steels.

Formation and evolution behavior of inclusions in Al-killed resulfurized free-cutting steel with magnesium treatment

To reveal the formation and evolution behavior of inclusions during magnesium treatment and resulfurization in Al-killed free-cutting steel, both laboratory experiments and thermodynamic calculations were carried out. The extracted samples were polished and analyzed by scanning electron microscopy and energy-dispersive spectroscopy. The results indicated that MgO formed immediately and then transferred to MgO·Al2O3 with the homogenization of [Mg] in steel in the case of low magnesium addition (w[Mg] < 0.0020%). However, MgO would keep stable in the case of high magnesium addition (w[Mg] ≥ 0.0020%). In the process of resulfurization, the addition of sulfur forced the transformation of MgO to MgO·Al2O3 accompanied with the formation of MgS if the mass fraction of [S] in steel was in the range 0.15%-0.70%. MgS precipi-tated as a solid solution containing a quantity of MnS, and the composition of the sulfide solution was calculated to be (Mg0.85Mn0.15)S when the mass fraction of [Mn] was 1.2%. The formation mechanisms of inclusions after magnesium and sulfur additions were discussed comprehensively, and proper models for the evolution of inclusions were set up.

Development and prospects of molten steel deoxidation in steelmaking process

In the long traditional process of steelmaking,excess oxygen is blown into the converter,and alloying elements are used for deoxidation.This inevitably results in excessive deoxidation of products remaining within the steel liquid,affecting the cleanliness of the steel.With the increasing requirements for steel performance,reducing the oxygen content in the steel liquid and ensuring its high cleanliness is necessary.After more than a hundred years of development,the total oxygen content in steel has been reduced from approximately 100×10^(-6)to approximately 10×10^(-6),and it can be controlled below 5×10^(-6)in some steel grades.A relatively stable and mature deoxidation technology has been formed,but further reducing the oxygen content in steel is no longer significant for improving steel quality.Our research team developed a deoxidation technology for bearing steel by optimizing the entire conventional process.The technology combines silicon–manganese predeoxidation,ladle furnace diffusion deoxidation,and vacuum final deoxidation.We successfully conducted industrial experiments and produced interstitial-free steel with natural decarbonization predeoxidation.Non-aluminum deoxidation was found to control the oxygen content in bearing steel to between 4×10^(-6) and 8×10^(-6),altering the type of inclusions,eliminating large particle Ds-type inclusions,improving the flowability of the steel liquid,and deriving a higher fatigue life.The natural decarbonization predeoxidation of interstitial-free steel reduced aluminum consumption and production costs and significantly improved the quality of cast billets.

FRACTAL GEOMETRY STUDY OF CORRELATION BETWEEN IMPACT TOUGHNESS OF STEEL AND PARAMETERS OF FREE-CUTTING PHASE

Studies were made of the calculation of fractal dimension of transverse impact fracture sur- face,and of the correlation between impact toughness of steel and parameters of free-cutting phase by means of the developed fractal geometry model of crack propagation.It is believed that the area fraction,f,of free-cutting phase is negligibly influential to the longitudinal im- pact toughness,as f1 .While the aspect ratio,saying ratio of length to width,of free-cut. ting phase is inversely influential to the transverse impact toughness.This may .be the reason why the transverse impact toughness of free-cutting steel containing more rare earth contrast to sulphur is even higher than the low sulphur containing steel.

Prediction model for corrosion rate of low-alloy steels under atmospheric conditions using machine learning algorithms

This work constructed a machine learning(ML)model to predict the atmospheric corrosion rate of low-alloy steels(LAS).The material properties of LAS,environmental factors,and exposure time were used as the input,while the corrosion rate as the output.6 dif-ferent ML algorithms were used to construct the proposed model.Through optimization and filtering,the eXtreme gradient boosting(XG-Boost)model exhibited good corrosion rate prediction accuracy.The features of material properties were then transformed into atomic and physical features using the proposed property transformation approach,and the dominant descriptors that affected the corrosion rate were filtered using the recursive feature elimination(RFE)as well as XGBoost methods.The established ML models exhibited better predic-tion performance and generalization ability via property transformation descriptors.In addition,the SHapley additive exPlanations(SHAP)method was applied to analyze the relationship between the descriptors and corrosion rate.The results showed that the property transformation model could effectively help with analyzing the corrosion behavior,thereby significantly improving the generalization ability of corrosion rate prediction models.

Flow characteristics and hot workability of a typical low-alloy high-strength steel during multi-pass deformation

Heavy components of low-alloy high-strength(LAHS) steels are generally formed by multi-pass forging. It is necessary to explore the flow characteristics and hot workability of LAHS steels during the multi-pass forging process, which is beneficial to the formulation of actual processing parameters. In the study, the multi-pass hot compression experiments of a typical LAHS steel are carried out at a wide range of deformation temperatures and strain rates. It is found that the work hardening rate of the experimental material depends on deformation parameters and deformation passes, which is ascribed to the impacts of static and dynamic softening behaviors. A new model is established to describe the flow characteristics at various deformation passes. Compared to the classical Arrhenius model and modified Zerilli and Armstrong model, the newly proposed model shows higher prediction accuracy with a confidence level of 0.98565. Furthermore, the connection between power dissipation efficiency(PDE) and deformation parameters is revealed by analyzing the microstructures. The PDE cannot be utilized to reflect the efficiency of energy dissipation for microstructure evolution during the entire deformation process, but only to assess the efficiency of energy dissipation for microstructure evolution in a specific deformation parameter state.As a result, an integrated processing map is proposed to better study the hot workability of the LAHS steel, which considers the effects of instability factor(IF), PDE, and distribution and size of grains. The optimized processing parameters for the multi-pass deformation process are the deformation parameters of 1223–1318 K and 0.01–0.08 s^(-1). Complete dynamic recrystallization occurs within the optimized processing parameters with an average grain size of 18.36–42.3 μm. This study will guide the optimization of the forging process of heavy components.

Influence of cold deformation on microstructure,mechanical properties,and corrosion resistance of high-sulfur free-cutting 316LS stainless steel

In this study,the influence of plastic deformation produced by cold rolling at reduction ratios ranging from 10% to 80% on the microstructure,mechanical properties,and pitting corrosion behavior of high-sulfur freecutting 316 LS austenitic stainless steel was investigated. The results indicate that slipping is the predominant effect and that sulfide inclusions extend along the rolling direction during the cold deformation of 316 LS. The strong austenite stability of 316 LS results in the formation of only a small quantity of deformation-induced martensite. The experimental results reveal that the strength,hardness,and yield ratio increased with increases in the reduction ratio,mainly due to work hardening,whereas the elongation decreased drastically,due to the combined effect of the work hardening and brittleness caused by the numerous sulfide inclusions. Electrochemically active sites on the surface of316 LS increased with an increased reduction ratio,which caused an increased current fluctuation in the passive zone. This also caused the breakdown potential（ E_b） near the pitting zone to exhibit a gradual increase in the zigzag current shift to the left on the polarization curves. The E_b of 316 LS decreased with increases in the reduction ratio,mainly due to the extended sulfide inclusions,the increased dislocation density,and the deformation-induced martensite content.

Recent progress in visualization and digitization of coherent transformation structures and application in high-strength steel

High-strength steels are mainly composed of medium-or low-temperature microstructures,such as bainite or martensite,with coherent transformation characteristics.This type of microstructure has a high density of dislocations and fine crystallographic structural units,which ease the coordinated matching of high strength,toughness,and plasticity.Meanwhile,given its excellent welding perform-ance,high-strength steel has been widely used in major engineering constructions,such as pipelines,ships,and bridges.However,visual-ization and digitization of the effective units of these coherent transformation structures using traditional methods(optical microscopy and scanning electron microscopy)is difficult due to their complex morphology.Moreover,the establishment of quantitative relationships with macroscopic mechanical properties and key process parameters presents additional difficulty.This article reviews the latest progress in microstructural visualization and digitization of high-strength steel,with a focus on the application of crystallographic methods in the development of high-strength steel plates and welding.We obtained the crystallographic data(Euler angle)of the transformed microstruc-tures through electron back-scattering diffraction and combined them with the calculation of inverse transformation from bainite or martensite to austenite to determine the reconstruction of high-temperature parent austenite and orientation relationship(OR)during con-tinuous cooling transformation.Furthermore,visualization of crystallographic packets,blocks,and variants based on actual OR and digit-ization of various grain boundaries can be effectively completed to establish quantitative relationships with alloy composition and key process parameters,thereby providing reverse design guidance for the development of high-strength steel.

Mechanical Behavior and Microstructure Evolution during Tensile Deformation of Twinning Induced Plasticity Steel Processed by Warm Forgings

The mechanical behavior and microstructural evolution of an Fe-30Mn-3Al-3Si twinninginduced plasticity(TWIP)steel processed using warm forging was investigated.It is found that steel processed via warm forging improves comprehensive mechanical properties compared to the TWIP steel processed via cold rolling,with a high tensile strength(R_(m))of 793 MPa,a yield strength(R_(P))of 682 MPa,an extremely large R_(P)/R_(m)ratio as high as 0.86 as well as an excellent elongation rate of 46.8%.The microstructure observation demonstrates that steel processed by warm forging consists of large and elongated grains together with fine,equiaxed grains.Complicated micro-defect configurations were also observed within the steel,including dense dislocation networks and a few coarse deformation twins.As the plastic deformation proceeds,the densities of dislocations and deformation twins significantly increase.Moreover,a great number of slip lines could be observed in the elongated grains.These findings reveal that a much more dramatic interaction between microstructural defect and dislocations glide takes place in the forging sample,wherein the fine and equiaxed grains propagated dislocations more rapidly,together with initial defect configurations,are responsible for enhanced strength properties.Meanwhile,larger,elongated grains with more prevalently activated deformation twins result in high plasticity.

Corrosion Test of the Steel Plate in a WJ-8 Fastener for High Speed Rail

It was found that the steel plate in the composite plate in the WJ-8 fastener used in high speed rail is rusty. The objective of this study is to test the zinc coating of the steel plate. A literature review was conducted to identify the zinc coating techniques, and the companies that can provide different coating service was identified. A salt fog chamber was built that was in compliance with the ANSI B117 code, and the steel plates that were coated by the identified companies were tested using the salt fog chamber. The results indicated that the coating technique that had the best performance in preventing corrosion was the Greenkote plates with passivation. The galvanized option had the roughest coating layer, and it was the most reactive in the salt water solution. This makes it non-ideal for the dynamic rail environment because the increased friction of the plate could damage the supports, especially during extreme temperatures that would cause the rail to expand or contract. Greenkote with Phosphate and ArmorGalv also provided increased corrosion prevention with a smooth, strong finish, but it had more rust on the surface area than the Greenkote with ELU passivation. The ArmorGalv sample had more rust on the surface area than the Greenkote samples. This may not be a weakness in the ArmorGalv process;rather, it likely was the result of this particular sample not having the added protection of a colored coating.

Critical precipitation behavior of MnTe inclusions in resulfurized steels during solidification

Te treatment is an effective method for modifying sulfide inclusions,and MnTe precipitation has an important effect on thermal brittleness and steel corrosion resistance.In most actual industrial applications of Te treatment,MnTe precipitation is unexpected.The critical precipitation behavior of MnTe inclusions was investigated through scanning electron microscopy,transmission electron microscopy,machine learning,and first-principles calculation.MnTe preferentially precipitated at the container mouth for sphere-like sulfides and at the interface between MnS grain boundaries and steel matrix for rod-like sulfides.The MnS/MnTe interface was semicoherent.A composition transition zone with a rock-salt structure exhibiting periodic changes existed to maintain the semicoherent interface.The critical precipitation behavior of MnTe inclusions in resulfurized steels involved three stages at varying temperatures.First,Mn(S,Te)precipitated during solidification.Second,MnTe with a rock-salt structure precipitated from Mn(S,Te).Third,MnTe with a hexagonal NiAs structure transformed from the rock-salt structure.The solubility of Te in MnS decreased with decreasing temperature.The critical precipitation behavior of MnTe inclusions in resulfurized steels was related to the MnS precipitation temperature.With the increase in MnS precipitation temperature,the critical Te/S weight ratio decreased.In consideration of the cost-effectiveness of Te addition for industrial production,the Te content in resulfurized steels should be controlled in accordance with MnS precipitation temperature and S content.

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Three types of steels were designed on the basis of GX40CrNiSi25-12 austenitic heat resistant steel by adding different Mn contents(2wt.%,6wt.%,and 12wt.%).Thermodynamic calculation,microstructure characterization and mechanical property tests were conducted to investigate the effect of Mn addition on the microstructure and mechanical properties of the austenitic heat resistant steel.Results show that the matrix structure in all the three types of steels at room temperature is completely austenite.Carbides NbC and M_(23)C_(6)precipitate at grain boundaries of austenite matrix.With the increase of Mn content,the number of carbides increases and their distribution becomes more uniform.With the Mn content increases from 1.99%to 12.06%,the ultimate tensile strength,yield strength and elongation increase by 14.6%,8.0%and 46.3%,respectively.The improvement of the mechanical properties of austenitic steels can be explained by utilizing classic theories of alloy strengthening,including solid solution strengthening,precipitation strengthening,and grain refinement.The increase in alloy strength can be attributed to solid solution strengthening and precipitation strengthening caused by the addition of Mn.The improvement of the plasticity of austenitic steels can be explained from two aspects:grain refinement and homogenization of precipitated phases.

Effects of iron oxide on crystallization behavior and spatial distribution of spinel in stainless steel slag

Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.

Microstructure Characteristics and Possible Phase Evolution of the Coal Gangue-Steel Slag Ceramics Prepared by the Solid-State Reaction Methods

Industrial wastes such as steel slag and coal gangue etc.were chosen as raw materials for preparing ceramic via the conventional solid-state reaction method.With steel slag and coal gangue mixed in various mass ratios,from 100%steel slag to 100%coal gangue at 10%intervals,microstructure and possible phase evolution of the coal gangue-steel slag ceramics were investigated using X-ray powder diffraction,scanning electron microscopy,mercury intrusion porosimetry and Archimedes boiling method.The experimental results suggest that the phase compositions of the as-prepared ceramics could be altered with the increased amount of coal gangue in the ceramics.The anorthite-diopside eutectic can be formed in the ceramics with the mass ratios of steel slag to coal gangue arranged from 8:2 to 2:8,which was responsible for the melting of the steel slag-coal gangue ceramics at relatively high temperature.Further investigations on the microstructure suggested that the addition of the proper amount of steel slag in ceramic compositions was conducive to the pore formation and further contributed to an increment in porosity.

Review on the plastic instability of medium -Mn steels for identifying the formation mechanisms of Lüders and Portevin -Le Chatelier bands

Plastic instability,including both the discontinuous yielding and stress serrations,has been frequently observed during the tensile deformation of medium-Mn steels(MMnS)and has been intensively studied in recent years.Unfortunately,research results are controversial,and no consensus has been achieved regarding the topic.Here,we first summarize all the possible factors that affect the yielding and flow stress serrations in MMnS,including the morphology and stability of austenite,the feature of the phase interface,and the deformation parameters.Then,we propose a universal mechanism to explain the conflicting experimental results.We conclude that the discontinuous yielding can be attributed to the lack of mobile dislocation before deformation and the rapid dislocation multiplication at the beginning of plastic deformation.Meanwhile,the results show that the stress serrations are formed due to the pinning and depinning between dislocations and interstitial atoms in austenite.Strain-induced martensitic transformation,influenced by the mechanical stability of austenite grain and deformation parameters,should not be the intrinsic cause of plastic instability.However,it can intensify or weaken the discontinuous yielding and the stress serrations by affecting the mobility and density of dislocations,as well as the interaction between the interstitial atoms and dislocations in austenite grains.