Effect of freeze-thaw cycles on uniaxial mechanical properties of cohesive coarse-grained soils

Freeze-thaw cycles are closely related to the slope instability in high-altitude mountain regions. In this study, cohesive coarse-grained soils were collected from a high-altitude slope in the Qinghai–Tibet Plateau to study the effect of cyclic freeze-thaw on their uniaxial mechanical properties. The soil specimens were remolded with three dry densities and three moisture contents. Then, after performing a series of freeze-thaw tests in a closed system without water supply, the soil specimens were subjected to a uniaxial compression test. The results showed that the stress-strain curves of the tested soils mainly performed as strain-softening. The softening feature intensified with the increasing dry density but weakened with an increase in freeze-thaw cycles and moisture content. The uniaxial compressive strength, resilient modulus, residual strength and softening modulus decreased considerably with the increase of freeze-thaw cycles. After more than nine freeze-thaw cycles, these four parameters tended to be stable. These parameters increased with the increase of dry density and decreased with the increasing moisture content, except for the residual strength which did not exhibit any clear variation with an increase in moisture content. The residual strength, however, generally increased with an increase in dry density. The soil structural damage caused by frozen water expansion during the freeze-thaw is the major cause for the changes in mechanical behaviors of cohesive coarse-grained soils. With results in this study, the deterioration effect of freeze-thaw cycles on the mechanical properties of soils should be considered during the slope stability analysis in high-altitude mountain regions.

Experimental study of dynamic resilient modulus of subgrade soils under coupling of freeze–thaw cycles and dynamic load

Although the dynamic properties of subgrade soils in seasonally frozen areas have already been studied, few researchers have considered the influence of shallow groundwater during the freeze–thaw(F–T) cycles. So a multifunctional F–T cycle system was developed to imitate the groundwater recharge in the subgrade during the freezing process and a large number of dynamic triaxial experiments were conducted after the F–T cycles. Some significant factors including the F–T cycle number, compaction degree, confining pressure, cyclic deviator stress, loading frequency, and water content were investigated for the resilient modulus of soils. The experimental results indicated that the dynamic resilient modulus of the subgrade was negatively correlated with the cyclic deviator stress, F–T cycle number, and initial water content, whereas the degree of compaction, confining pressure, and loading frequency could enhance the resilient modulus. Furthermore, a modified model considering the F–T cycle number and stress state was established to predict the dynamic resilient modulus. The calculated results of this modified model were very close to the experimental results. Consequently, calculation of the resilient modulus for F–T cycles considering the dynamic load was appropriate. This study provides reference for research focusing on F–T cycles with groundwater supply and the dynamic resilient moduli of subgrade soils in seasonally frozen areas.

Freeze-thaw processes of active-layer soils in the Nanweng'he River National Natural Reserve in the Da Xing'anling Mountains,northern Northeast China

The active-layer soils overlying the permafrost are the most thermodynamically active zone of rock or soil and play important roles in the earth-atmosphere energy system. The processes of thawing and freezing and their associated complex hydrothermal coupling can significantly affect variation in mean annual temperatures and the formation of ground ice in permafrost regions. Using soil-temperature and-moisture data obtained from the active layer between September 2011 and October 2014 in the permafrost region of the Nanweng'he River in the Da Xing'anling Mountains, the freeze-thaw characteristics of the permafrost were studied. Based on analysis of ground-temperature variation and hydrothermal transport characteristics, the thawing and freezing processes of the active layer were divided into three stages:(1) autumn-winter freezing,(2) winter freeze-up, and(3) spring-summer thawing. Variations in the soil temperature and moisture were analyzed during each stage of the freeze-thaw process, and the effects of the soil moisture and ground vegetation on the freeze-thaw are discussed in this paper. The study's results show that thawing in the active layer was unidirectional, while the ground freezing was bidirectional(upward from the bottom of the active layer and downward from the ground surface).During the annual freeze-thaw cycle, the migration of soil moisture had different characteristics at different stages. In general, during a freezing-thawing cycle, the soil-water molecules migrate downward, i.e., soil moisture transports from the entire active layer to the upper limit of the permafrost. In the meantime, freeze-thaw in the active layer can be significantly affected by the soil-moisture content and vegetation.

Surface crack evolution patterns in freeze-thaw damage of fissured rock bodies

To explore the effects of freeze‒thaw cycles on the mechanical properties and crack evolution of fissured sandstone,biaxial compression experiments were carried out on sandstone subjected to freeze‒thaw cycles to characterize the changes in the physical and mechanical properties of fissured sandstone caused by freeze‒thaw cycles.The crack evolution and crack change process on the surface of the fissured sandstone were recorded and analysed in detail via digital image technology(DIC).Numerical simulation was used to reveal the expansion process and damage mode of fine-scale cracks under the action of freeze‒thaw cycles,and the simulation results were compared and analysed with the experimental data to verify the reliability of the numerical model.The results show that the mass loss,porosity,peak stress and elastic modulus all increase with increasing number of freeze‒thaw cycles.With an increase in the number of freeze‒thaw cycles,a substantial change in displacement occurs around the prefabricated cracks,and a stress concentration appears at the crack tip.As new cracks continue to sprout at the tips of the prefabricated cracks until the microcracks gradually penetrate into the main cracks,the displacement cloud becomes obviously discontinuous,and the contours of the displacement field in the crack fracture damage area simply intersect with the prefabricated cracks to form an obvious fracture.The damage patterns of the fractured sandstone after freeze‒thaw cycles clearly differ,forming a symmetrical"L"-shaped damage pattern at zero freeze‒thaw cycles,a symmetrical"V"-shaped damage pattern at 10 freeze‒thaw cycles,and a"V"-shaped damage pattern at 20 freeze‒thaw cycles.After 20 freeze‒thaw cycles,a"V"-shaped destruction pattern and"L"-shaped destruction pattern are formed;after 30 freeze‒thaw cycles,an"N"-shaped destruction pattern is formed.This shows that the failure mode of fractured sandstone gradually becomes more complicated with an increasing number of freeze‒thaw cycles.The effects of freeze‒thaw cycles on the direction and rate of crack propagation are revealed through a temperature‒load coupled model,which provides an important reference for an in-depth understanding of the freeze‒thaw failure mechanisms of fractured rock masses.

Effects of freeze-thaw cycles on sandstone in sunny and shady slopes

A growing rock engineering activity in cold regions is facing the threat of freeze-thaw(FT)weathering,especially in high mountains where the sunny-shady slope effects strongly control the difference in weathering behavior of rocks.In this paper,an investigation of the degradation of petrophysical characteristics of sandstone specimens subjected to FT cycle tests to simulate the sunny-shady slope effects is presented.To this aim,non-destructive and repeatable testing techniques including weight,ultrasonic waves,and nuclear magnetic resonance methods on standard specimens were performed.For the sunny slope specimens,accompanied by the enlargement of small pores,100 FT cycles caused a significant decrease in P-wave velocity with an average of 23%,but a consistent rise of 0.18%in mass loss,34%in porosity,67%in pore geometrical mean radius,and a remarkable 14.5-fold increase in permeability.However,slight changes with some abnormal trends in physical parameters of the shady slope specimens were observed during FT cycling,which can be attributed to superficial granular disaggregation and pore throat obstruction.Thermal shocks enhance rock weathering on sunny slopes during FT cycles,while FT weathering on shady slopes is restricted to the small pores and the superficial cover.These two factors are primarily responsible for the differences in FT weathering intensity between sunny and shady slopes.The conclusions derived from the interpretation of the experimental results may provide theoretical guidance for the design of slope-failure prevention measures and the selection of transportation routes in cold mountainous regions.

Quantification of the concrete freeze–thaw environment across the Qinghai–Tibet Plateau based on machine learning algorithms

The reasonable quantification of the concrete freezing environment on the Qinghai–Tibet Plateau(QTP) is the primary issue in frost resistant concrete design, which is one of the challenges that the QTP engineering managers should take into account. In this paper, we propose a more realistic method to calculate the number of concrete freeze–thaw cycles(NFTCs) on the QTP. The calculated results show that the NFTCs increase as the altitude of the meteorological station increases with the average NFTCs being 208.7. Four machine learning methods, i.e., the random forest(RF) model, generalized boosting method(GBM), generalized linear model(GLM), and generalized additive model(GAM), are used to fit the NFTCs. The root mean square error(RMSE) values of the RF, GBM, GLM, and GAM are 32.3, 4.3, 247.9, and 161.3, respectively. The R^(2) values of the RF, GBM, GLM, and GAM are 0.93, 0.99, 0.48, and 0.66, respectively. The GBM method performs the best compared to the other three methods, which was shown by the results of RMSE and R^(2) values. The quantitative results from the GBM method indicate that the lowest, medium, and highest NFTC values are distributed in the northern, central, and southern parts of the QTP, respectively. The annual NFTCs in the QTP region are mainly concentrated at 160 and above, and the average NFTCs is 200 across the QTP. Our results can provide scientific guidance and a theoretical basis for the freezing resistance design of concrete in various projects on the QTP.

Effects of Freeze–thaw Cycles on Soil Mechanical and Physical Properties in the Qinghai–Tibet Plateau

Extreme freeze-thaw action occurs on the Qinghai-Tibet Plateau due to its unique climate resulting from high elevation and cold temperature.This action causes damage to the surface soil structure, as soil erosion in the Qinghai-Tibet Plateau is dominated by freeze-thaw erosion.In this research,freezing–thawing process of the soil samples collected from the Qinghai–Tibet Plateau was carried out by laboratory experiments to determinate the volume variation of soil as well as physical and mechanical properties, such as porosity, granularity and uniaxial compressive strength, after the soil experiences various freeze–thaw cycles.Results show that cohesion and uniaxial compressive strength decreased as the volume and porosity of the soil increased after experiencing various freeze–thaw cycles, especially in the first six freeze–thaw cycles.Consequently, the physical and mechanical properties of the soil were altered.However, granularity and internal friction angle did not vary significantly with an increase in the freeze–thaw cycle.The structural damage among soil particles due to frozen water expansion was the major cause of changes in soil mechanical behavior in the Qinghai–Tibet Plateau.

Cracking in an expansive soil under freeze–thaw cycles

Expansive soils located in cold regions can easily endure the action of frost heaving and cyclic freezing–thawing. Cracking can also occur in expansive clayey soils under freeze–thaw cycles, of which little attention has been paid on this issue.In this study, laboratory experiment and cracking analysis were performed on an expansive soil. Crack patterns were quantitatively analyzed using the fractal concept. The relationships among crack pattern, water loss, number of freeze–thaw cycles, and fractal dimension were discussed. It was found that crack patterns on the surface exhibit a hierarchical network structure that is fractal at a statistical level. Cracks induced by freeze–thaw cycles are shorter, more irregularly oriented,and slowly evolves from an irregularly rectilinear pattern towards a polygonal or quasi–hexagonal one; water loss, closely related to specimen thickness, plays a significant role in the process of soil cracking; crack development under freeze-thaw cycles are not only attributed to capillary effect, but also to expansion and absorption effects.

Effects of freeze-thaw on soil erosion processes and sediment selectivity under simulated rainfall

The freeze-thaw （FT） processes affect an area of 46.3% in China. It is essential for soil and water conservation and ecological construction to elucidate the mechanisms of the FF processes and its associated soil erosion processes. In this research, we designed the control simulation experiments to promote the understanding of FT-water combined erosion processes. The results showed that the runoff of freeze-thaw slope （FTS） decreased by 8% compared to the control slope （CS）, and the total sediment yield of the FTS was 1.10 times that of the CS. The sediment yield rate from the FTS was significantly greater than that from the CS after 9 min of runoff （P〈0.01）. Both in FTS and CS treatments, the relationships between cumulative runoff and sediment yield can be fitted well with power functions （R2〉0.98, P〈0.01）. Significant differences in the mean weight diameter （MWD） values of particles were between the CS and the FTS treatments in the erosion were smaller than those under FTS for both washed and observed for washed particles and splashed particles process （P〈0.05）. The mean MWD values under CS splashed particles. The ratio of the absolute value of a regression coefficient between the CS and the FTS was 1.15, being roughly correspondent with the ratio of K between the two treatments. Therefore, the parameter a of the power function between cumulative runoff and sediment yield could be an acceptable indicator for expressing the soil erodibility. In conclusion, the FTS exhibited an increase in soil erosion compared to the CS.

Effects of freeze–thaw cycles on soil N_2O concentration and flux in the permafrost regions of the Qinghai–Tibetan Plateau

Nitrous oxide(N_2 O) is one of the most important greenhouse gases in the atmosphere; freeze–thaw cycles(FTCs) might strongly influence the emission of soil N_2 O on the Qinghai–Tibetan Plateau(QTP). However, there is a lack of in situ research on the characteristics of soil N_2 O concentration and flux in response to variations in soil properties caused by FTCs.Here, we report the effect of FTC-induced changes in soil properties on the soil N_2 O concentration and flux in the permafrost region of the higher reaches of the Shule River Basin on the northeastern margin of the QTP. We measured chemical properties of the topsoil, activities of soil microorganisms, and air temperature(AT), as well as soil N_2 O concentration and flux, over an annual cycle from July 31, 2011, to July 30, 2012. The results showed that soil N_2 O concentration was significantly affected by soil temperature(ST), soil moisture(SM), soil salinity(SS), soil polyphenol oxidase(SPO), soil alkaline phosphatase(SAP), and soil culturable actinomycetes(SCA), ranked as SM>SS>ST>SPO>SAP>SCA, whereas ST significantly increased soil N_2 O flux, compared with SS. Overall, our study indicated that the soil N_2 O concentration and flux in permafrost zone FTCs were strongly affected by soil properties, especially soil moisture, soil salinity, and soil temperature.

Comments on thaw-freeze algorithms for multilayered soil,using the Stefan equation

The Stefan equation provides a useful and widely used method for predicting the depth of thawing and freezing in a soil where little site-specific information is available. The original Stefan equation was derived for only a homogeneous medium, and some algorithms have been developed for its use in a multilayered system. However, although the Stefan equation was derived more than 100 years ago, there is not a unified understanding for its use in a multilayered system. This paper examines the use of the Stefan equation in multilayered soil, based on comparing three algorithms(JL-algorithm, NM-algorithm, and XG-algorithm). We conclude that the JL and NM algorithms are incorrect, as they arose from flawed mathematical derivations. Both of these algorithms failed to recognize that the thawing depth in a multilayered soil is a piecewise function and not a continuous function of time. This work asserts that the XG-algorithm is a correct and rigorous method to determine the freezing–thawing fronts in multilayered soil.

Calculation of salt-frost heave of sulfate saline soil due to long-term freeze−thaw cycles

Based on salt-frost heave tests of sulfate saline soil under repeated freeze−thaw cycles,this paper discusses the mechanism of the salt-frost heave under long-term freeze−thaw cycles.The results show that the salt-frost heave can be restricted considerably by loads,and there is a critical load for the salt-frost heave cumulative effect.Under this load,peak values of salt-frost heave approach a constant,and the residual values become 0.There is no longer structure heave or cumulative effect of saline soil exposed to freeze−thaw cycles under the critical load.Taking cumulative effect into account in calculations of salt-frost heave,a salt-frost heave model under freeze−thaw cycles is developed.

Review of the influence of freeze-thaw cycles on the physical and mechanical properties of soil

Seasonally frozen soil is a four-phase material and its physical-mechanical properties are more complex compared to the unfrozen soil. Its physical properties changes during the freeze-thaw process; repeated fieeze-thaw cycles change the characteristics of soil, which can render the soil from an unstable state to a new dynamic equilibrium state. The freezing process changes the structttre coupled between the soil particle arrangements, which will change the mechanical properties of the soil. The method of significance and interaction between different fac tors should be considered to measure the influence on the propties of soil under freeze-thaw cycles.

Potential methane and nitrous oxide production and respiration rates from penguin and seal colony tundra soils during freezing–thawing cycles under different water contents in coastal Antarctica

In coastal Antarctica, frequent freezing-thawing cycles （FTCs） and changes to the hydrological conditions may affect methane （CH4） and nitrous oxide （N2O） production and respiration rates in tundra soils, which are difficult to observe in situ. Tundra soils including omithogenic tundra soil （OAS）, seal colony soil （SCS） and emperor penguin colony soil （EPS） were collected. In laboratory, we investigated the effects of FTCs and water addition on potential N2O and CH4 production and respiration rates in the soils. The CH4 fluxes from OAS and SCS were much less than that from EPS. Meanwhile, the N2O fluxes from OAS and EPS were much less than that from SCS. The N2O production rates from all soils were extremely low during freezing, but rapidly increased following thawing. In all cases, FTC also induced considerably enhanced soil respiration, indicating that soil respiration response was sensitive to the FTCs. The highest cumulative rates of CH4, N2O and CO2 were 59.5 mg CH4-C·kg-1 in EPS, 6268.8μg N2O-N·kg-1 in SCS and 3522.1mg CO2-C·kg-1 in OAS. Soil water addition had no significant effects on CH4 production and respiration rates, but it could reduce N2O production in OAS and EPS, and it stimulated N2O production in SCS. Overall, CH4 and N2O production rates showed a trade-off relationship during the three FTCs. Our results indicated that FTCs greatly stimulated soil N2O and CO2 production, and water increase has an important effect on soil N2O production in coastal Antarctic tundra.

Review and prospect of the effects of freeze-thaw on soil geotechnical properties

Freeze-thaw hazard is one of the main problems in cold regions engineering and artificial ground freezing engineering.To mitigate freeze-thaw hazards,it is essential to investigate the effects of freeze-thaw on soils engineering properties.This paper summarizes the effects of freeze-thaw on the physical and mechanical properties of soils reported in recent studies.The differences of freeze-thaw conditions between freezing shaft sinking and cold regions engineering are discussed.Based on the technological characteristics of freezing shaft sinking in deep alluvium,we further attempt to identify key research needs regarding the freeze-thaw effects on the engineering properties of deep soils.

Spatial and temporal variability of soil freeze-thaw cycling across Southern Alberta, Canada

Soil freeze-thaw cycles play an important role in all aspects of agro-ecosystems, such as crop productivity, the evolution of the soil matrix, including trace-gas emissions. In regions that experience synoptic weather conditions throughout the winter, freeze-thaw cycles generally occur in one of two categories;seasonal or winter cycles. Current soil vegetation atmosphere models (SVAT’s) often include a heat-transport soil freeze-thaw algorithm, but lack detail on complex interactions between the main driving variables. Boundary conditions for these models are often based only on a few climate variables and typically lack regional context. A nested statistical analysis was applied to identify the optimal set of environmental variables (via a stepwise regression selection procedure) to track soil freeze-thaw dynamics. Historical data collected between the years 2006-2009, for 17 long-term climate stations distributed across southern Alberta Canada was utilized. Cross-correlation between wind speed and maximum air temperature identified Chinook-driven freeze-thaw events, with such interaction varying significantly across the region and by soil depth. Climate-soil interactions were most significant predictors of soil temperature during winter months. The seasonal freeze-thaw cycle is estimated to vary between 112 - 131 days, consisting of 12 - 20 winter cycles (1 cm depth), and 1-5 winter cycles (5 cm depth) with average lag time of 26 - 112 days. Freeze-thaw prediction was greatly improved when higher-order climate interaction terms were considered. Our findings highlight the importance for soil-water and more complex ecosystem, SVAT models to better resolve regional-driven climatic trends. Alongside improved representation of regional trends aimed at reducing model-based uncertainty, such efforts are expected to, in tandem, help advance the geostatistical design, and implementation of agroenvironmental monitoring systems that combine in-situ and satellite/remote-sensing derived estimates of near-surface soil moisture.

Wind tunnel simulation of the effects of freeze–thaw cycles on soil erosion in the Qinghai–Tibet Plateau

Intense freezing and thawing actions occur in the Qinghai-Tibet Plateau because of its high elevation and cold temperature. The plateau＇s unique environment makes it easy to generate wind erosion under dry, windy weather conditions, resulting in the emergence ofdesertification. As a major form of freeze-thaw erosion, freeze-thaw and wind erosion is displayed prominently on the Qinghai-Tibet Plateau. Therefore, in this study, soil samples were collected from the surface of the plateau to undergo freeze-thaw and wind erosion simulation experiments. Results show that wind erosion strength increases with an increasing number of freeze-thaw cycles, water content in the freezing-thawing process, and the difference in freeze-thaw temperatures. Therefore, in the conditions of water participation, the main reason for the freeze-thaw and wind erosion in the Qinghai-Tibet Plateau is the damage to the soil structure by repeated, fierce freeze-thaw actions, and the sand-bearing wind is the main driving force for this process. The research results have theoretical significance for exploring the formation mechanism of freeze-thaw and wind erosion in the Qinghai-Tibet Plateau, and provide a scientific basis for freeze-thaw desertification control in the plateau.

Spatial-temporal variations in near-surface soil freeze-thaw cycles in the source region of the Yellow River during the period 2002–2011 based on the Advanced Microwave Scanning Radiometer for the Earth Observing System(AMSR-E) data

Detecting near-surface soil freeze-thaw cycles in high-altitude cold regions is important for understanding the Earth＇s surface system, but such studies are rare. In this study, we detected the spatial-temporal variations in near-surface soil freeze-thaw cycles in the source region of the Yellow River（SRYR） during the period 2002–2011 based on data from the Advanced Microwave Scanning Radiometer for the Earth Observing System（AMSR-E）. Moreover, the trends of onset dates and durations of the soil freeze-thaw cycles under different stages were also analyzed. Results showed that the thresholds of daytime and nighttime brightness temperatures of the freeze-thaw algorithm for the SRYR were 257.59 and 261.28 K, respectively. At the spatial scale, the daily frozen surface（DFS） area and the daily surface freeze-thaw cycle surface（DFTS） area decreased by 0.08% and 0.25%, respectively, and the daily thawed surface（DTS） area increased by 0.36%. At the temporal scale, the dates of the onset of thawing and complete thawing advanced by 3.10（±1.4） and 2.46（±1.4） days, respectively; and the dates of the onset of freezing and complete freezing were delayed by 0.9（±1.4） and 1.6（±1.1） days, respectively. The duration of thawing increased by 0.72（±0.21） day/a and the duration of freezing decreased by 0.52（±0.26） day/a. In conclusion, increases in the annual minimum temperature and winter air temperature are the main factors for the advanced thawing and delayed freezing and for the increase in the duration of thawing and the decrease in the duration of freezing in the SRYR.

Study on the freezing–thawing deformation of consolidated soils under high pressure

The freezing-thawing deformation behaviors of consolidated soils under high pressure have been investigated in a high-pressure-low-temperature （HPLT） Kq consolidation apparatus with a small strain sensor. The tests cover a variety of frozen soil temperatures ranging from -2℃ to -10 ℃, and a series of applied pressures ranging from 1 MPa to 5 MPa. The test results show that, for the consolidated soils under high pressure, their freezing-thawing deformation was caused by the realignment and the deformation of soil particles, the phase change of water, and the water redistribution in the soil. As for the deformation produced by thermal expansion and contraction,it is about 0.04-0.05 mm, accounting for only about 7%~9% of the total deformation. Taking the freezing-thawing deformation produced by temperature disturbance as a creep deformation, the creep models of the developing soil deformation will be determined by the soil＇s final temperature, i.e., the desired temperature. For the soils under a desired temperature between -2℃ and -5℃, the freezing-thawing de-formation develops according to a non-attenuation creep model; but for the soils with a desired temperature lower than -5℃, a full attenuation creep model is followed. The applied pressure and soil type also have a significant influence on the maximum freezing deformation. Generally, the greater the desired pressure applied, the less the maximum deformation is; and the loess freezing deformation is larger than that of sand.

A dynamic soil freezing characteristic curve model for frozen soil

The soil freezing characteristic curve(SFCC)plays a fundamental role in comprehending thermohydraulic behavior and numerical simulation of frozen soil.This study proposes a dynamic model to uniformly express SFCCs amidst varying total water contents throughout the freezing-thawing process.Firstly,a general model is proposed,wherein the unfrozen water content at arbitrary temperature is determined as the lesser of the current total water content and the reference value derived from saturated SFCC.The dynamic performance of this model is verified through test data.Subsequently,in accordance with electric double layer(EDL)theory,the theoretical residual and minimum temperatures in SFCC are calculated to be-14.5℃to-20℃for clay particles and-260℃,respectively.To ensure that the SFCC curve ends at minimum temperature,a correction function is introduced into the general model.Furthermore,a simplified dynamic model is proposed and investigated,necessitating only three parameters inherited from the general model.Additionally,both general and simplified models are evaluated based on a test database and proven to fit the test data exactly across the entire temperature range.Typical recommended parameter values for various types of soils are summarized.Overall,this study provides not only a theoretical basis for most empirical equations but also proposes a new and more general equation to describe the SFCC.