Electric-controlled metasurface antenna array with ultra-wideband frequency reconfigurable reflection suppression

The electric-controlled metasurface antenna array(ECMSAA)with ultra-wideband frequency reconfigurable reflection suppression is proposed and realized.Firstly,an electriccontrolled metasurface with ultra-wideband frequency reconfigurable in-phase reflection characteristics is designed.The element of the ECMSAA is constructed by loading the single electric-controlled metasurface unit on the conventional patch antenna element.The radiation properties of the conventional patch antenna and the reflection performance of electric-controlled metasurface are maintained when the antenna and the metasurface are integrated.Thus,the ECMSAA elements have excellent radiation properties and ultra-wideband frequency reconfigurable in-phase reflection characteristics simultaneously.To take a further step,a 6×10 ECMSAA is realized based on the designed metasurface antenna element.Simulated and measured results prove that the reflection of the ECMSAA is dynamically suppressed in the P and L bands.Meanwhile,high-gain and multi-polarization radiation properties of the ECMSAA are achieved.This design method not only realizes the frequency reconfigurable reflection suppression of the antenna array in the ultra-wide frequency band but also provides a way to develop an intelligent low-scattering antenna.

Cactus-Shaped Frequency Reconfigurable Antenna for Sub 10 GHz Wireless Applications

This paper presents,a novel cactus shaped frequency reconfigurable antenna for sub 10 GHz wireless applications.PIN diode is utilized as an electrical switch to achieve reconfigurability,enabling operation in four different frequency ranges.In the switch ON state mode,the antenna supports 2177-3431 and 6301-8467 MHz ranges.Alternatively,the antenna resonates within 2329-3431 and 4951-6718 MHz while in the OFF state mode.Radiation efficiency values,ranging from 68%to 84%,and gain values,ranging from 1.6 to 4 dB,in the operating frequency bands.the proposed antenna satisfy the practical requirements and expectations.The overall planner dimensions of the proposed antenna model is 40×21 mm^(2).Moreover,the measurement results from the prototype support the simulation results.Based on the frequency ranges supported by the antenna,it can be used for multiple wireless standards and services,including Worldwide interoperability and Microwave Access(WiMAX),Wireless Fidelity(Wi-Fi),Bluetooth,Long Term Evolution(LTE)and satellite communications.This increases its applicability for use in mobile terminals.

Ultrahigh frequency tunability of aperture-coupled microstrip antenna via electric-field tunable BST

A composite ceramic with nominal composition of 45.0 wt%（Ba0.5Sr0.5）TiO3–55.0 wt%MgO（acronym is BST–MgO） is sintered for fabricating a frequency reconfigurable aperture-coupled microstrip antenna. The calcined BST–Mg O composite ceramic exhibits good microwave dielectric properties at X-band with appropriate dielectric constant εr around85, lower dielectric loss tan δ about 0.01, and higher permittivity tunability 14.8% at 8.33 k V/cm. An ultrahigh E-field tunability of working frequency up to 11.0%（i.e., from 9.1 GHz to 10.1 GHz with a large frequency shift of 1000 MHz）at a DC bias field from 0 to 8.33 k V/cm and a considerably large center gain over 7.5 d B are obtained in the designed frequency reconfigurable microstrip antenna. These results demonstrate that BST materials are promising for the frequency reconfigurable antenna.

Multi-Mode Frequency Reconfigurable Conformal Antenna for Modern Electronic Systems

The article presents a miniaturized monopole antenna dedicated to modern flexible electronic systems.The antenna combines three fundamental properties in a single structure.Firstly,it is characterized by a compact size compared to the state-of-the-art literature with an overall size of 18×18×0.254 mm3,secondly,the proposed antenna integrates the reconfigurability function of frequency,produced by means of a Positive-IntrinsicNegative(PIN)diode introduced into the radiating element.Thus,the antenna is able to switch between different frequencies and different modes,making it suitable to meet the ever-changing demands of communication systems.third,the antenna is equipped by the property of flexibility.In fact,a conformability test is performed and has demonstrated the stability of the antenna performance under normal and bending conditions.Finally,in order to demonstrate the potential of the proposed antenna,a comparison between the simulated and measured results is made and turned out to be a strong agreement,making the antenna an excellent candidate for future miniaturized rigid and conformal devices.

Frequency Reconfigurable Antenna for Portable Wireless Applications

In this paper,the design and experimental evaluation of a hexagonalshaped coplanar waveguide(CPW)-feed frequency reconfigurable antenna is presented using flame retardant(FR)-4 substrate with size of 37×35×1.6 mm3.The antenna is made tunable to three different modes through the status of two pin diodes to operate in four distinct frequency bands,i.e.,2.45 GHz wireless fidelity(Wi-Fi)in MODE 1,3.3 GHz(5G sub-6 GHz band)in MODE 2,2.1 GHz(3G Long Term Evolution(LTE)-advanced)and 3.50 GHz Worldwide Interoperability for Microwave Access(WiMAX)in MODE 3.The optimization through simulation modeling shows that the proposed antenna can provide adequate gain(1.44∼2.2 dB),sufficient bandwidth(200∼920 MHz)and high radiation efficiency(80%∼95%)in the four resonating frequency bands.Voltage standing wave ratio(VSWR)<1.5 is achieved for all bands with properly matched characteristics of the antenna.To validate the simulation results,fabrication of the proposed optimized design is performed,and experimental analysis is found to be in a considerable amount of agreement.Due to its reasonably small size and support of multiple frequency bands operation,the proposed antenna can support portable devices for handheld 5G and Wireless LAN(WLAN)applications.

Wideband Reconfigurable Millimeter-Wave Linear Array Antenna Using Liquid Crystal for 5G Networks

The advanced design of a 10 × 1 linear antenna array system with the capa-bility of frequency tunability using GT3-23001 liquid crystal (LC) is pro-posed. The design for this reconfigurable wideband antenna array for 5G ap-plications at Ka-band millimeter-wave (mmw) consists of a double layer of stacked patch antenna with aperture coupled feeding. The bias voltage over LC varies from 0 V to 10.6 V to achieve a frequency tunability of 1.18 GHz. The array operates from 25.3 GHz to 33.8 GHz with a peak gain of 19.2 dB and a beamwidth of 5.2° at 30 GHz. The proposed reconfigurable antenna ar-ray represents a real and efficient solution for the recent and future mmw 5G networks. The proposed antenna is suitable for 5G base stations in stadiums, malls and convention centers. It is proper for satellite communications and radars at mmw.

Frequency reconfigurable antenna actuated by inflated triangular structure:Design and analysis

This paper proposes a frequency reconfigurable triangular antenna actuated by an inflated triangular structure.The open path antenna is transformed from an open type to a closed structure by inflating.Inflatable structures are easy to manufacture by fusing 2 inextensible membranes together along a defined pattern of lines.However,the prediction of their deployed shape remains a challenge.To solve the pattern changed problem,guided by geometric analyses and local buckle characteristics,the inflated triangular structure has been designed and verified by experiment and simulation.In the process of transformation of the antenna,the resonant frequency of the antenna is changed because this frequency is determined by the conformational change.The resonant frequency changes from GHz to kHz when the design of initial structure sizes is from millimeter to meter.The measured peak gains,the frequency,and the radiation direction are also reconfigurable by the initial size.Finally,the reconfigurable resonator array is presented,which is coupled to electric fields to absorb all incident radiation.In this work,the changed pattern design by inflating is applied to the antenna design,and its frequency reconfigurability is achieved.Through the electricity performance analysis of the reconfigurable antenna,precise manufacturing will be possible and provide guidance for manufacturing frequency reconfigurable antennas.

RF MEMS Based Reconfigurable Rectangular Slotted Self Similar Antenna

Wireless communication systems which require flexibility and reconfigurability in antenna systems faces main problems like antenna performance, size, weight and cost. A wide band Frequency Reconfigurable Rectangular Slotted Self Similar Antenna has been proposed in this paper. The rectangular slotted patch is repeated for two iterations at different scales and is separated by means of Radio Frequency Micro Electro Mechanical Systems (RF MEMS) switches in order to provide reconfigurability. The antenna can operate in three frequency bandsi.e. K-band, Ku-band and Ka-band by altering the states of RF MEMS switches. To avoid fringing effects and to improve antenna performance, quarter wavelength (λ/4) spacing is required between the antenna and the ground plane. However, a Reconfigurable Antenna requires different λ/4 spacing which is difficult to achieve using a common ground plane. So the Frequency Reconfigurable antenna is integrated with high impedance surface (HIS) like Electronic Band Gap (EBG) structures to suppress standing waves and surface waves with a unified profile thickness of 1.75 mm. The overall dimension of the proposed antenna along with RF MEMS Switch, feed element and HIS is about 8 mm × 8 mm × 1.75 mm. The simulated results of the proposed antenna reveal enhancement in antennas performance like Voltage Standing Wave Ratio (VSWR), Front to Back Ratio (FBR) and bandwidth when it is placed over HIS EBG. Also the radiation patterns of the proposed antenna when placed over EBG shows the suppression of side lobe and backward radiation.