Novel forward mode AC/AC converters with high frequency link

A circuit configuration and a circuit topologic family of the novel forward mode AC/AC converters with high frequency link are presented. The circuit configuration is constituted of input cycloconverter, high frequency transformer, output cycloconverter, input and output filters. The circuit topologic family includes eight circuit topologies, such as full-bridge-full-wave mode, etc. The bi-polarity phase-shifted control strategy and steady principles are thoroughly investigated. The output characteristics are obtained. By using the bi-polarity phase-shifted control strategy with phase-shifted control between the output cycloconveter and the input cycloconverter, commutation overlap period of the output cycloconverter, and polarity selection of the output filtering inductance current and the input voltage, the leakage inductance energy and the output filtering inductance current are naturally commutated, and surge voltage and surge current of the cycloconverters are overcome. The converters have such advantages as simple topology, two-stage power conversions(LFAC/HFAC/LFAC), bi-directional power flow, high frequency electrical isolation, good output waveforms, and strong ability to stabilize voltage. The converters lay key technical foundation on a new-type of regulated sinusoidal AC power supplies and electronic transformers. The correction and advancement of the converters are well verified by a principle test.

Zero-voltage switching converter absorbing parasitic parameters for super high frequency induction heating

This paper presents a novel mega-Hz-level super high frequency zero-voltage soft-switching converter for induction heating power supplies. The prominent advantage of this topology is that it can absorb both inductive and capacitive parasitic components in the converter. The switch devices operate in a zero-voltage soft-switching mode. Consequently, the high voltage and high current spikes caused by parasitic inductors or capacitors oscillation do not occur in this circuit, and the high power loss caused by high frequency switching can be greatly reduced. A large value inductor is adopted between the input capacitor and the switches, thus, this novel converter shares the benefits of both voltage-type and current-type circuits simultaneously, and there are no needs of dead time between two switches. The working principles in different modes are introduced. Results of simulation and experiments operated at around 1 MHz frequency verify the validity of parasitic components absorption and show that this convener is competent for super high frequency applications.

Variable Frequency Modulation for EMI Suppressing in Power Converter

Switch mode power supply (SMPS) is good selection for power supplies of Unmanned Aerial Vehicle (UAV), which is one of the most important interference sources of UAV. The power switches with their high dv/dt and di/dt switching slopes are the sources of electromagnetic interference (EMI). In this paper, a variable frequency modulation technology of the forward converter of UAV is presented, which is utilized in SMPS to improve electromagnetic compatibility (EMC). In variable-frequency techniques, power (signal) is transmitted in power converter in wide-band mode in several frequencies that are constantly changing, the EMI spectral performance of the SMPS can be controlled with the modulating pattern and modulation method. The validity of the models and analyses are confirmed experimentally by using a dc/dc forward converter.

Effects of switching frequency and leakage inductance on slow-scale stability in a voltage controlled flyback converter

The effects of both the switching frequency and the leakage inductance on the slow-scale stability in a voltage controlled flyback converter are investigated in this paper. Firstly, the system description and its mathematical model are presented. Then, the improved averaged model, which covers both the switching frequency and the leakage inductance, is established, and the effects of these two parameters on the slow-scale stability in the system are analyzed. It is found that the occurrence of Hopf bifurcation in the system is the main reason for losing its slow-scale stability and both the switching frequency and the leakage inductance have an important effect on this slow-scale stability. Finally, the effectiveness of the improved averaged model and that of the corresponding theoretical analysis are confirmed by the simulation results and the experimental results.

Development of OPTO-LDR coupled timer based voltage to frequency converter

This paper describes the development of a timer based voltage to frequency converter(V FC).Timer LM555is used in astable multivibrator mode with two OPTO-LDRs(light dependent resistors)in the circuitry.The frequency of timer output waveform which is measured using a digital storage oscillator(DSO)is almost linearly proportional to the applied input voltage.Hence we obtain a linear relationship between the frequency of timer output waveform and the input voltage.Because of its quasi-digital output,the main advantages of this developed converter are linear input-output relationship,small size,easy portabilityand high cost performance.In addition,the timer output waveform can be directly interfaced with personal computer or microprocessor/microcontroller for further processing of the input voltage signal without intervening any analog-to-digital converter(ADC).

Analysis of Soft-Switched High Frequency AC-AC Converter for Induction Motor Drive

The systematic mathematical analysis of the high frequency soft-switched AC-AC converter is proposed for variable frequency induction machine load in this paper. Both PWM and square-wave modes of operation have been considered. The frequency relation and phase unbalance problem due to discrete time integral half-cycle switching has been discussed in the beginning. Then, generalized Fourier series have been derived for output voltage, output current and supply current in two modes.The analytical results help to understand tbe converter characteristics, design optimally a convertermachine system of arbitrary capacity considering the various trade-off parameters.

Fast-transient techniques for high-frequency DC–DC converters

A 30 MHz voltage-mode controlled buck converter with fast transient responses is presented.An improved differential difference amplifier(DDA)-based Type-III compensator is proposed to reduce the settling times of the converter during load transients,and to achieve near-optimal transient responses with simple PWM control only.Moreover,a hybrid scheme using a digital linear regulator with automatic transient detection and seamless loop transition is proposed to further improve the transient responses.By monitoring the output voltage of the compensator instead of the output voltage of the converter,the proposed hybrid scheme can reduce undershoot and overshoot effectively with good noise immunity and without interrupting the PWM loop.The converter was fabricated in a 0.13μm standard CMOS process using 3.3 V devices.With an input voltage of 3.3 V,the measured peak efficiencies at the output voltages of 2.4,1.8,and 1.2 V are 90.7%,88%,and 83.6%,respectively.With a load step of 1.25 A and rise and fall times of 2 ns,the measured 1%settling times were 220 and 230 ns,with undershoot and overshoot with PWM control of 72 and 76 mV,respectively.They were further reduced to 36 and 38 mV by using the proposed hybrid scheme,and 1%settling times were also reduced to 125 ns.

Phasor Control of Converter Output Voltage for Frequency Regulation

The synchronizing torque of a power system may be weakened by increasing installation of static power converters accompanied by renewable energy resources because they used to trade their favorable active power by synchronizing their output voltage with the one at the point of common coupling. In the circumstances, a concept of Virtual Synchronous Machine (VSM) is proposed, where the self-commutated power converters are emulating synchronous generators. This paper describes a converter control to contribute to enhancing the synchronizing torque. The proposed control is similar to the VSM but it simply realizes active power trades among power generation units including converter-based generators by modulating phase angles of their output voltages. Therefore, it can provide an effective support to regulate the system frequency where the total rated power of the converter-based generators increases as much as the one of conventional rotating generators like a microgrid. This paper especially focuses on its robustness where the number of converter-based generators is increased or they are dispersed in the power network. The effectiveness is verified by simulation study based on instantaneous values.

A linear-to-circular polarization converter based on I-shaped circular frequency selective surfaces

In this paper, a linear-to-circular polarization converter using a three-layer frequency selective surface based on Ishaped circular structure resonant is presented and investigated. Numerical simulations exhibit that when the normal ypolarized waves impinge on this device propagating towards ＋z direction, the two orthogonal components of the transmitted waves have a 90° phase difference as well as the nearly equal amplitudes at the resonant frequency of 7.04 GHz, which means that the left-hand circular polarization is realized in transmission. For validating the proposed design, a prototype which consists of 25 × 25 elements has been designed, manufactured and measured. The measured results are in good agreement with the simulated ones, showing that the polarization conversion transmission is over-3 dB in the frequency range of 5.22–8.08 GHz and the axial ratio is below 3 dB from 5.86 GHz to 7.34 GHz.

Application of Dual Throttling Air-Conditioning System to Explosion-Proof Frequency Converter

An explosion-proof dual throttling air-conditioning system was put forward to solve the heat dissipation and internal dewing problems of explosion-proof frequency converter in the underground coal mine. This study investigated the feasibility and benefits of explosion-proof dual throttling cooling and dehumidification air-conditioning system applied to the explosion-proof frequency converter. The physical model of dual throttling air-conditioning system was established and its performance parameter was described by mathematical method. The design calculation of the system has also been done. The experimental result showed that the system reached the steady state at the refrigeration mode after running 45 min, and the maximum internal temperature of the flame-proof cavity was 31.0 ℃. The system reached the steady state at the dehumidification mode after running 37 min. The maximum internal relative humidity and temperature of the flame-proof cavity were 33.4% and 36.3 ℃, respectively. Therefore, the proposed system had excellent ability of heat dissipation and avoided internal dewing. Compared with water cooling system, it was more energy-saving and economical. The airflow field of dual throttling air-conditioning system was also studied by CFD simulation. It was found that the result of CFD numerical simulation was highly consistent with the experimental data.

Bifurcation and chaos in high-frequency peak current mode Buck converter

Bifurcation and chaos in high-frequency peak current mode Buck converter working in continuous conduction mode（CCM） are studied in this paper. First of all, the two-dimensional discrete mapping model is established. Next, reference current at the period-doubling point and the border of inductor current are derived. Then, the bifurcation diagrams are drawn with the aid of MATLAB. Meanwhile, circuit simulations are executed with PSIM, and time domain waveforms as well as phase portraits in i_L–v_C plane are plotted with MATLAB on the basis of simulation data. After that, we construct the Jacobian matrix and analyze the stability of the system based on the roots of characteristic equations. Finally, the validity of theoretical analysis has been verified by circuit testing. The simulation and experimental results show that,with the increase of reference current I_（ref）, the corresponding switching frequency f is approaching to low-frequency stage continuously when the period-doubling bifurcation happens, leading to the converter tending to be unstable. With the increase of f, the corresponding Irefdecreases when the period-doubling bifurcation occurs, indicating the stable working range of the system becomes smaller.

Design of low-power high-frequency digital controlled DC-DC switching power converter

This paper models a low-power high-frequency digitally controlled synchronous rectifier （SR） OUCK converter. The converter is a hybrid system with three operation modes. Digital PID controler is used. Key problems such as quantization resolution of digital pulse-width modulation （DPWM） and steady-state limit cycles of digital control switching model power supply （SMPS） are discussed, with corresponding solutions presented. Simulation of a digital control synchronous buck is performed with a fixed-point algorithm. The results show that the described approach enables high-speed dynamic performance.

Frequency Range Dependent TE₁₀to TE₄₀Metallic Waveguide Mode Converter

Dielectric rod arrays in a metallic waveguide alter the propagation modes and group velocities of electromagnetic waves. We focus on TE10-to-TE20 mode converters and investigate the variation in their behavior with frequency. In this investigation, a mode converter is proposed that passes the TE10 mode at frequencies lower than 2fc, and converts the TE10 mode into the TE40 mode for frequencies higher than 2fc, which is achieved by a combination of TE10-TE20 mode converters.

A study on frequency domain mathematics model of arc welding reverse converter

Arc welding converter (AWC) power source is a nonlinear and discrete abnormal system. It is difficult to get the accurate analytic solution in theory. In this paper, an average state equation of the system is established by means of state space analysis method. The mathematics model of the reverse converter is gotten after the average equation of the system is linearized. The model is a two ranks oscillation link. With the parameters of the AWC, when the condition of (1/RC) 2 >>4/LC is available, the mathematics model may be simplified to a serial structure which includes a integral link and a one rank inertia link. On the basis of this, it can be analyzed and rectified in frequency domain, then some groups of reality rectification parameters are gotten around the theory rectification parameters. These groups of parameters are taken to do the resistance load experiment and welding technology experiment. The result of experiment accords with the theory analysis result. This paper also provides some practical analysis of the model under the large signal process such as the sudden opening of the load, short circuit, turning on and turning off the machine. The result of the research shows that the power source system of AWC can be analyzed and rectified by the frequency domain analysis method in the engineering. The deduced mathematics model of small signal average frequency domain shows the basic characteristics of the system, and the structure parameters of the system is formed by R, L, C and switching ratio D. The model is very simple and clear, and it can be used to analyze and design the power source system of AWC and it can also be used to direct the regulation for dynamic characteristics of the system.

Model predictive control of three-level active front-end converter with low switching frequency

In medium voltage-high power(MV-HP)applications,the high switching frequency of power converter will result in unnecessary energy losses,which directly affect efficiency.To resolve this issue,a novel finite control set-model predictive control(FCS-MPC)with low switching frequency for three-level neutral point clamped-active front-end converters(NPC-AFEs)is proposed.With this approach,the prediction model of three-level NPC-AFEs is established inα-βreference frame,and the control objective of low average switching frequency is introduced into a cost function.The proposed method not only achieves the desired control performance under low switching frequency,but also performs the efficient operation for the three-level NPC-AFEs.The simulation results are provided to verify the effectiveness of proposed control scheme.

Equilibrium mechanism between dc voltage and ac frequency for ac-dc interlinking converters

The equilibrium between dc bus voltage and ac bus frequency(Udc-f equilibrium)is the algorithm core of unified control strategies for ac-dc interlinking converters(ILCs),because the equilibrium implements certain mechanism.However,what the mechanism is has not been explicitly explored,which hinders further studies on unified control.This paper reveals that the state-space model of a Udc-f equilibrium controlled ILC is highly similar to that of a shaft-to-shaft machines system.Hence a detailed mechanism is dis-covered and named“virtual shaft-to-shaft machine(VSSM)”mechanism.A significant feature of VSSM mechanism is self-synchro-nization without current sampling or ac voltage sampling.

Current Distortion Evaluation in Traction 4Q Constant Switching Frequency Converters

The paper deals with the power quality analysis of interlaced four quadrant (4Q) converters with constant switching frequency. These are in fact the input stages of the locomotives and high speed trains supplied by 25 kV, 50 Hz and 15 kV, 16.7 Hz lines. Due to the high power needed for the trains circulation, the 4Q converter can absorb distorted currents, whose harmonic content can affect the signaling systems and communication devices. The presence of more converters gives the opportunity, using dedicated commutation strategy, to interlace them in order to reduce the harmonic content in the absorbed current. In the paper a suitable model of more 4Q converters is developed. The control logic implemented in the model allows the evaluation of the harmonic contribution of both single converter and the interlaced configuration. The analysis is carried out through electromagnetic transient simulations.

A novel polarization converter based on the band-stop frequency selective surface

A dual-passband single-polarized converter based on the band-stop frequency selective surface(FSS)with a low radar cross-section(RCS)is designed in this article.The unit cell of the proposed converter is formed by a polarization layer attached to the band-stop frequency selective surface.The simulation results reveal that the co-polarization reflection coefficients below-10 d B are achieved in 3.82–13.64 GHz with a 112.4%fractional bandwidth(the ratio of the signal bandwidth to the central frequency).Meanwhile,a polarization conversion band is realized from 8.14 GHz to 9.27 GHz with a polarization conversion ratio which is over 80%.Moreover,the 1 d B transmission window is obtained in two nonadjacent bands of 3.42–7.02 GHz and 10.04–13.91 GHz corresponding to the relative bandwidths of 68.9%and 32.3%,respectively.Furthermore,the radar cross-section of the designed structure can be reduced in the wideband from 2.28 GHz to 14 GHz,and the 10 d B RCS reduction in the range of 4.10–13.35 GHz is achieved.In addition,the equivalent circuit model of this converter is established,and the simulation results of the Advanced Design System(ADS)match well with those of CST Microwave Studio(CST).The archetype of the designed converter is manufactured and measured.The experiment results match the simulation results well,which proves the reliability of the simulation results.

Experiment of Frequency Range Dependent TE10 to TE20 Mode Converter

Typical metallic waveguide mode converters convert electromagnetic waves from one mode to another mode for some frequency ranges. However, most electromagnetic waves outside of the specified frequency range are reflected. We report a design for a mode converter which passes the TE10 mode at a low frequency range and efficiently converts the TE10 mode to the TE20 mode at a high frequency range. To gradually shift the mode profile from TE10 to TE20, dielectric rods are placed in a sequence along the waveguide starting near the sidewall and moving to the center of the waveguide with decreasing radius of the rods. This design reduces reflection of electromagnetic waves. Experimental tests demonstrate the efficacy of the design.

The Low-Frequency Oscillation Restrain Method Research of Converter-Fed Multi-Phase Induction Motor Propulsion system

The inverter-fed induction motor drive system may become unstable at low frequencies and light load, and phase current and speed of the induction motor may oscillate periodically, which will threaten safety and reliability of the system. This paper chooses nine-phase induction motor simulated propulsion system as the research object, small disturbance model of three-phase induction motor is built, and average equivalent model of the converter is built by introducing switch function. On the basis above, small disturbance mathematic model of the whole system is obtained. As for the limitation of parameters adjustment method of restrain low-frequency oscillation, the restrain method combining current close-loop with dead-time compensation is put forward. Finally, the proposed restrain method is verified respectively on the built simulation and experimental analogue platform. And the simulation and experimental results indicate that the proposed method can not only satisfy the requirement of low-frequency oscillation restraining, but also be expanded widely, and the stability of the system can get improved greatly.