Frequency-dependent Electrical Capacitance and Resistance of Ultra-high Performance Concrete and Their Responses to Compressive Strain

The frequency-dependent electrical properties and strain self-sensing behaviour of ultra-high performance concrete(UHPC)as cement-based stress/strain self-sensing(CBSS)smart materials were investigated in the frequency range from 100 Hz to 300 kHz.By using the electrical parameters of the equivalent electric circuit model,the quantitative relations of capacitance and conductance of CBSS with the measurement frequency were derived.The capacitance and the conductance exhibit power-law type dependence on the measurement frequency.The calculated capacitance values at frequencies beyond 2 kHz and conductance values are consistent with the experimental results.The sweep-frequency test and the fixed-frequency test were performed to examine effects of the excitation frequencies on strain self-sensing properties of CBSS.The fractional change in capacitance(FCC)and resistance(FCR)of CBSS are frequency-dependent in the frequency range from 100 Hz to the f_(B),but frequency-independent in the frequency range from the f_(B)to 300 kHz.The f_(A)and the f_(B)are 1.7-4.0 kHz and 11-78 kHz depending on the fiber dosages,respectively.FCC and FCR reach their maximum at the f_(A)and 100 Hz,respectively.The responses of capacitance and resistance of CBSS to strain show good repeatability during cyclic loading.As the fiber dosage increases,capacitance-based sensitivity to strain increases initially and then decreases at the f_(A),and resistance-based sensitivity to strain of CBSS increases with increasing fiber contents.

Equivalent linear model for seismic damage evaluation of single-degree-of-freedom systems representing reinforced concrete structures considering cyclic degradation behavior

In this study,a novel equivalent damping ratio model that is suitable for reinforced concrete(RC)structures considering cyclic degradation behavior is developed,and a new equivalent linearization analysis method for implementing the proposed equivalent damping ratio model for use in seismic damage evaluation is presented.To this end,Ibarra’s peak-oriented model,which incorporates an energy-based degradation rule,is selected for representing hysteretic behavior of RC structure,and the optimized equivalent damping for predicting the maximum displacement response is presented by using the empirical method,in which the effect of cyclic degradation is considered.Moreover,the relationship between the hysteretic energy dissipation of the inelastic system and the elastic strain energy of the equivalent linear system is established so that the proposed equivalent linear system can be directly integrated with the Park-Ang seismic model to implement seismic damage evaluation.Due to the simplicity of the equivalent linearization method,the proposed method provides an efficient and reliable way of obtaining comprehensive insight into the seismic performance of RC structures.The verification demonstrates the validity of the proposed method.

Effect of astigmatism and spherical equivalent correction on contrast sensitivity

AIM:To investigate the effect of astigmatism and spherical equivalent(SE)correction on contrast sensitivity(CS).METHODS:In this cross-sectional study,103 visually normal subjects aged 18 to 36y with bilateral regular astigmatism in range of 1.00 diopter cylinder(DC)to 4.00 DC and normal best-corrected visual acuity(20/20)were recruited.Binocular CS was assessed by linear sine-wave gratings at 1.5,3,6,12,and 18 cycles per degree(cpd),before correction of astigmatism,after full correction of astigmatism by cylindrical spectacle lenses,and after SE of refractive error.The repeated measures ANOVA and Bonferroni test were used to compare the effects of astigmatism correction on logCS.RESULTS:Totally 39 patients were male and 64 patients were female with the mean age of 28.25±5.38y.The average degree of astigmatism in right and left eye was 2.03±0.83 and 2.10±0.78,respectively.Increases in uncorrected astigmatic power correlated with decreases in the logCS,especially at high spatial frequencies.A statistically significant difference in logCS was found between these three cases:before correction of astigmatism,after SE of refractive error,and after full correction of astigmatism by cylindrical spectacle lenses at all frequencies(P<0.001),except at 18 cpd.At 18 cpd,there was no statistically significant difference between logCS before and after SE of refractive error(P=1.0).Also,there was no statistically significant difference in mean CS between with-the-rule(WTR)and against-the-rule(ATR)astigmatism,before correction of astigmatism,after correction of astigmatism with cylindrical lenses,and after SE of refractive error.CONCLUSION:Binocular astigmatism defocus decreases CS depending on the degree of astigmatism power;correction of this will improve patent’s quality of vision.Although high astigmatism refractive error(more than 2.00 DC)that is fully corrected by cylindrical spectacle lenses doesn’t increase the CS to the maximum value,especially at higher spatial frequencies(12 and 18).Also SE refractive error effects on improving CS in low astigmatism power(less than 2.00 DC),especially at lower spatial frequencies.

An equivalent target plate damage probability calculation mathematics model and damage evaluation method

Aiming at the requirement of damage testing and evaluation of equivalent target plate based on the explosion of intelligent ammunition, this paper proposes a novel method for damage testing and evaluation method of circumferential equivalent target plate. Leveraging the dispersion characteristics parameters of fragment, we establish a calculation model of the fragment power situation and the damage calculation model under the condition of fragment ultimate penetration equivalent target plate. The damage model of equivalent target plate involves the fragment dispersion density, the local perforation damage criterion, the tearing damage model, and the damage probability. We use the camera to obtain the image of the equivalent target plate with fragment perforation, and research the algorithm of fragment distribution position recognition and fragment perforation area calculation method on the equivalent target plate by image processing technology. Based on the obtained parameters of the breakdown position and perforation area of fragments on equivalent target plate, we apply to damage calculation model of equivalent target plate, and calculate the damage probability of each equivalent target plate, and use the combined probabilistic damage calculation method to obtain the damage evaluation results of the circumferential equivalent target plate in an intelligent ammunition explosion experiment. Through an experimental testing, we verify the feasibility and rationality of the proposed damage evaluation method by comparison, the calculation results can reflect the actual damage effect of the equivalent target plate.

An efficient approach for the equivalent linearization of frame structures with plastic hinges under nonstationary seismic excitations

An efficient approach is proposed for the equivalent linearization of frame structures with plastic hinges under nonstationary seismic excitations.The concentrated plastic hinges,described by the Bouc-Wen model,are assumed to occur at the two ends of a linear-elastic beam element.The auxiliary differential equations governing the plastic rotational displacements and their corresponding hysteretic displacements are replaced with linearized differential equations.Then,the two sets of equations of motion for the original nonlinear system can be reduced to an expanded-order equivalent linearized equation of motion for equivalent linear systems.To solve the equation of motion for equivalent linear systems,the nonstationary random vibration analysis is carried out based on the explicit time-domain method with high efficiency.Finally,the proposed treatment method for initial values of equivalent parameters is investigated in conjunction with parallel computing technology,which provides a new way of obtaining the equivalent linear systems at different time instants.Based on the explicit time-domain method,the key responses of interest of the converged equivalent linear system can be calculated through dimension reduction analysis with high efficiency.Numerical examples indicate that the proposed approach has high computational efficiency,and shows good applicability to weak nonlinear and medium-intensity nonlinear systems.

Analysis of secondary makeup characteristics of drill collar joint and prediction of downhole equivalent impact torque of Well SDTK1

Based on the three-dimensional elastic-plastic finite element analysis of the 8"(203.2 mm)drill collar joint,this paper studies the mechanical characteristics of the pin and box of NC56 drill collar joints under complex load conditions,as well as the downhole secondary makeup features,and calculates the downhole equivalent impact torque with the relative offset at the shoulder of internal and external threads.On the basis of verifying the correctness of the calculation results by using measured results in Well GT1,the prediction model of the downhole equivalent impact torque is formed and applied in the first extra-deep well with a depth over 10000 m in China(Well SDTK1).The results indicate that under complex loads,the stress distribution in drill collar joints is uneven,with relatively higher von Mises stress at the shoulder and the threads close to the shoulder.For 203.2 mm drill collar joints pre-tightened according to the make-up torque recommended by American Petroleum Institute standards,when the downhole equivalent impact torque exceeds 65 kN·m,the preload balance of the joint is disrupted,leading to secondary make-up of the joint.As the downhole equivalent impact torque increases,the relative offset at the shoulder of internal and external threads increases.The calculation results reveal that there exists significant downhole impact torque in Well SDTK1 with complex loading environment.It is necessary to use double shoulder collar joints to improve the impact torque resistance of the joint or optimize the operating parameters to reduce the downhole impact torque,and effectively prevent drilling tool failure.

An improved algorithm based on equivalent sound velocity profile method at large incident angle

With the development of ultra-wide coverage technology,multibeam echo-sounder(MBES)system has put forward higher requirements for localization accuracy and computational efficiency of ray tracing method.The classical equivalent sound speed profile(ESSP)method replaces the measured sound velocity profile(SVP)with a simple constant gradient SVP,reducing the computational workload of beam positioning.However,in deep-sea environment,the depth measurement error of this method rapidly increases from the central beam to the edge beam.By analyzing the positioning error of the ESSP method at edge beam,it is discovered that the positioning error increases monotonically with the incident angle,and the relationship between them could be expressed by polynomial function.Therefore,an error correction algorithm based on polynomial fitting is obtained.The simulation experiment conducted on an inclined seafloor shows that the proposed algorithm exhibits comparable efficiency to the original ESSP method,while significantly improving bathymetry accuracy by nearly eight times in the edge beam.

Subsidence prediction method based on equivalent mining height theory for solid backfilling mining

Based on the characteristics of strata movement of solid backfilling mining technology, the surface subsidence prediction method based on the equivalent mining height theory was proposed, and the parameters selection guideline of this method was also described. While comparing the parameters of caving mining with equivalent height, the subsidence efficient can be calculated according to the mining height and bulk factor of sagging zone and fracture zone, the tangent of main influence angle of solid backfilling mining is reduced by 0.2-0.5（while it cannot be less than 1.0）. For sake of safety, offset of the inflection point is set to zero, and other parameters, such as horizontal movement coefficient and main propagation angle are equal to the corresponding parameters of caving mining with equivalent height. In the last part, a case study of solid backfilling mining subsidence prediction was described. The results show the applicability of this method and the difference of the maximum subsidence point between the prediction and the observation is less than 5%.

Effect of gas bubble on cell voltage oscillations based on equivalent circuit simulation in aluminum electrolysis cell

A method to investigate the effect of gas bubble on cell voltage oscillations was established. The whole aluminum electrolysis cell was treated as a resistance circuit, and the dynamic simulation of the cell equivalent circuit was modeled with Matlab/Simulink simulation software. The time-series signals of cell voltage and anode current were obtained under different bubble conditions, and analyzed by spectral and statistical analysis methods. The simulation results show that higher bubble release frequency has a significant effect on the cell voltage oscillations. When the bubble coverage of one anode block exceeds 80%, the cell voltage may exceed its normal fluctuation amplitude. The simulation also proves that the anode effect detected by computer in actual production is mainly the whole cell anode effect.

The analysis of frequency-dependent characteristics for fluid detection: a physical model experiment

According to the Chapman multi-scale rock physical model, the seismic response characteristics vary for different fluid-saturated reservoirs. For class I AVO reservoirs and gas-saturation, the seismic response is a high-frequency bright spot as the amplitude energy shifts. However, it is a low-frequency shadow for the Class III AVO reservoirs saturated with hydrocarbons. In this paper, we verified the high-frequency bright spot results of Chapman for the Class I AVO response using the frequency-dependent analysis of a physical model dataset. The physical model is designed as inter-bedded thin sand and shale based on real field geology parameters. We observed two datasets using fixed offset and 2D geometry with different fluid- saturated conditions. Spectral and time-frequency analyses methods are applied to the seismic datasets to describe the response characteristics for gas-, water-, and oil-saturation. The results of physical model dataset processing and analysis indicate that reflection wave tuning and fluid-related dispersion are the main seismic response characteristic mechanisms. Additionally, the gas saturation model can be distinguished from water and oil saturation for Class I AVO utilizing the frequency-dependent abnormal characteristic. The frequency-dependent characteristic analysis of the physical model dataset verified the different spectral response characteristics corresponding to the different fluid-saturated models. Therefore, by careful analysis of real field seismic data, we can obtain the abnormal spectral characteristics induced by the fluid variation and implement fluid detection using seismic data directly.

Equivalent Circuit Analysis of an RF Integrated Inductor with Ferrite Thin-Film

An equivalent circuit for a novel RF integrated inductor with ferrite thin-film is derived. The enhancement of the magnetic ferrite thin-film on the inductance （L） and quality factor （Q） of the inductor is analyzed. Circuit element parameters are extracted from RF measurements. Compared with the reference air-core inductor without magnetic film, L and Q of the ferrite thin-film inductor are 17% and 40% higher at 2GHz,respectively. Both the equivalent circuit analysis and test results demonstrate significant enhancement of the performance of RF integration inductors by ferrite thin-film integration.

COMPACT FOUR-COMPONENT 2-D FDFD METHOD WITH EQUIVALENT SURFACE IMPEDANCE BOUNDARY CONDITION FOR MULTILAYER METAL-COATED WAVEGUIDE

A compact four-component two-dimensional （2-D） finite-difference frequency domain （FDFD） method with the equivalent surface impedance boundary condition is used to analyze the dispersion characteristics of multilayer metal-coated waveguides. According to the equivalent surface impedance boundary condition,the relationship between transverse field components on the boundary can be easily depicted. Once the eigen equation is solved,the propagation constant can be obtained as the eigen value for a given frequency. Results of the proposed method agaree well with those of high frequency structure simulator（HFSS）.

Small-Signal Equivalent Circuit Modeling of a Photodetector Chip

A small-signal equivalent circuit model and the ted. The equivalent lumped circuit, which takes the main extraction techniques for photodetector chips are presen- factors that limit a photodetector＇s RF performance into consideration,is first determined based on the device＇s physical structure. The photodetector＇s S parameters are then on-wafer measured, and the measured raw data are processed with further calibration. A genetic algorithm is used to fit the measured data, thereby allowing us to calculate each parameter value of the model. Experimental resuits show that the modeled parameters are well matched to the measurements in a frequency range from 130MHz to 20GHz, and the proposed method is proved feasible. This model can give an exact description of the photodetector chip＇s high frequency performance,which enables an effective circuit-level prediction for photodetector and optoelectronic integrated circuits.

Equivalent Method of Integrated Power Generation System of Wind, Photovoltaic and Energy Storage in Power Flow Calculation and Transient Simulation

针对工程实际开展风光储联合发电系统在潮流计算和机电暂态仿真中的等值方法研究，旨在为大容量风光储联合发电系统的并网仿真分析奠定基础。将潮流计算的等值分为单元机组和集电系统2部分来研究。单元机组等值采用根据不同控制模式选取不同节点类型的方法，针对集电系统等值提出基于损耗不变原则的方法。等值模型和详细模型的算例结果表明，潮流计算等值方法具有较好的精度。在机电暂态仿真动态等值中，基于实际工程计算的最严重工况分析原则，提出运行在满出力点的单机“倍乘”等值模型，为工程计算中的风光储联合发电系统动态等值提供了一种解决方案。

Fluid identification based on frequency-dependent AVO attribute inversion in multi-scale fracture media

A key problem in seismic inversion is the identification of the reservoir fluids. Elastic parameters, such as seismic wave velocity and formation density, do not have sufficient sensitivity, thus, the conventional amplitude-versus-offset（AVO） method is not applicable. The frequency-dependent AVO method considers the dependency of the seismic amplitude to frequency and uses this dependency to obtain information regarding the fluids in the reservoir fractures. We propose an improved Bayesian inversion method based on the parameterization of the Chapman model. The proposed method is based on 1） inelastic attribute inversion by the FDAVO method and 2） Bayesian statistics for fluid identification. First, we invert the inelastic fracture parameters by formulating an error function, which is used to match observations and model data. Second, we identify fluid types by using a Markov random field a priori model considering data from various sources, such as prestack inversion and well logs. We consider the inelastic parameters to take advantage of the viscosity differences among the different fluids possible. Finally, we use the maximum posteriori probability for obtaining the best lithology/fluid identification results.

Seismic dynamic monitoring in CO_2 flooding based on characterization of frequency-dependent velocity factor

The phase velocity of seismic waves varies with the propagation frequency, and thus frequency-dependent phenomena appear when CO2 gas is injected into a reservoir. By dynamically considering these phenomena with reservoir conditions it is thus feasible to extract the frequency-dependent velocity factor with the aim of monitoring changes in the reservoir both before and after CO2 injection. In the paper, we derive a quantitative expression for the frequency-dependent factor based on the Robinson seismic convolution model. In addition, an inversion equation with a frequency-dependent velocity factor is constructed, and a procedure is implemented using the following four processing steps： decomposition of the spectrum by generalized S transform, wavelet extraction of cross-well seismic traces, spectrum equalization processing, and an extraction method for frequency-dependent velocity factor based on the damped least-square algorithm. An attenuation layered model is then established based on changes in the Q value of the viscoelastic medium, and spectra of migration profiles from forward modeling are obtained and analyzed. Frequency-dependent factors are extracted and compared, and the effectiveness of the method is then verified using a synthetic data. The frequency-dependent velocity factor is finally applied to target processing and oil displacement monitoring based on real seismic data obtained before and after CO2 injection in the G89 well block within Shengli oilfield. Profiles and slices of the frequency-dependent factor determine its ability to indicate differences in CO2 flooding, and the predicting results are highly consistent with those of practical investigations within the well block.

New text classification algorithm based on interdependence and equivalent radius

To improve the traditional classifying methods, such as vector space model （VSM）-based methods with highly complicated computation and poor scalability, a new classifying method （ called IER） is presented based on two new concepts： interdependence and equivalent radius. In IER, the attribute is selected according to the value of interdependence, and the classifying rule is based on equivalent radius and center of gravity. The algorithm analysis shows that IER is good at classifying a large number of samples with higher scalability and lower computation complexity. After several experiments in classifying Chinese texts, the conclusion is drawn that IER outperforms k-nearest neighbor （kNN） and classifcation based on the center of classes （CCC） methods, so IER can be used online to automatically classify a large number of samples while keeping higher precision and recall.

Relationship Between Noise Figure and Equivalent Input Noise Current Spectral Density for Optical Receiver Design

Based on the equivalent circuit model of a two-port optical receiver front-end,the relationship between the equivalent input noise current spectral density and the noise figure is analyzed. The derived relationship has universal validity for determining the equivalent input noise current spectral density for optical receiver designs, as verified by measuring a 155Mb/s high-impedance optical receiver front.end. Good agreement between calculated and simulated results has been achieved.

THE EQUIVALENT CIRCUIT AND CONTROL SYSTEM OF TRAVELLING WAVE TYPE ULTRASONIC MOTOR

The ultrasonic motor is a sort of new type of micromotor with special structure. By use of piezoelectric converse effect of ceramics, the electrical energy is transformed into mechanical energy. Its operating principle is quite different from that of the traditional motors. In this paper the equivalent circuits of the ring stator and even the whole motor are proposed after studying the equivalent circuit of piezoelectric vibrator. Then the paper makes detailed analyses of each part of the control system, which has been simplified by the equivalent circuit. The theory in this paper has been proved through experiments.

Abstraction of Small Signal Equivalent Circuit Parameters of Enhancement-Mode InGaP/AlGaAs/InGaAs PHEMT

An extraction method of the component parameter values of an enhancement-mode InGaP/AIGaAs/In-GaAs PHEMT small signal equivalent circuit is presented,and these component parameter values are extracted by using the EEHEMT1 model of IC-CAP software. The extraction results are verified by ADS software,and the DC I-V curves and S parameters simulated by ADS are basically accordant with those of the test results. These results indicate that the EEHEMT1 model can be used for extracting the component parameters of an enhancement-mode PHEMT.