Degradation of acid fuchsine by a modified electro-Fenton system with magnetic stirring as oxygen supplying

The current modified electro-Fenton system was designed to develop a more convenient and efficient undivided system for practical wastewater treatment. The system adopted a cathode portion that employed magnetic stirring instead of common oxygen gas diffusion or gas sparging to supply oxygen gas for the electrolyte solution. Key factors influencing the cathode fabrication and activit） were investigated. The degradation of acid fuchsine with a self-made graphite-polytetrafluorethylene cathode was studied using spectrophotometer. It was found that the cathode generated hydrogen peroxide with high current efficiency and the hydrogen peroxide yield of the cathode did not decay after 10 times reuse. With the Pt anode at a ferrous ion concentration of 0.5 mmol/L, a pH of 3, and using magnetic stirring, dye decolorization could be rapidly accomplished but the destruction of benzene rings and intermediates was fairly difficult. With a Fe anode, dye degradation was more complete.

Preparation of activated carbon from sunflower straw through H_(3)PO_(4) activation and its application for acid fuchsin dye adsorption

With the development circular economy, the use of agricultural waste to prepare biomass materials to remove pollutants has become a research hotspot. In this study, sunflower straw activated carbon (SSAC) was prepared by the one-step activation method, with sunflower straw (SS) used as the raw material and H3PO4 used as the activator. Four types of SSAC were prepared with impregnation ratios (weight of SS to weight of H3PO4) of 1:1, 1:2, 1:3, and 1:5, corresponding to SSAC1, SSAC2, SSAC3, and SSAC4, respectively. The adsorption process of acid fuchsin (AF) in water using the four types of SSAC was studied. The results showed that the impregnation ratio significantly affected the structure of the materials. The increase in the impregnation ratio increased the specific surface area and pore volume of SSAC and improved the adsorption capacity of AF. However, an impregnation ratio that was too large led to a decrease in specific surface area. SSAC3, with an impregnation ratio of 1:3, had the largest specific surface area (1 794.01 m2/g), and SSAC4, with an impregnation ratio of 1:5, exhibited the smallest microporosity (0.052 7 cm3/g) and the largest pore volume (2.549 cm3/g). The adsorption kinetics of AF using the four types of SSAC agreed with the quasi-second-order adsorption kinetic model. The Langmuir isotherm model was suitable to describe SSAC3 and SSAC4, and the Freundlich isotherm model was appropriate to describe SSAC1 and SSAC2. The result of thermodynamics showed that the adsorption process was spontaneous and endothermic. At 303 K, SSAC4 showed a removal rate of 97.73% for 200-mg/L AF with a maximum adsorption capacity of 2 763.36 mg/g, the highest among the four types of SSAC. This study showed that SAAC prepared by the H3PO4-based one-step activation method is a green and efficient carbon material and has significant application potential for the treatment of dye-containing wastewater.

Spectroscopic and Electrochemical Studies of the Interaction Between Fuchsin Basic and DNA

Visible spectroscopic and electrochemical methods were used to study the interactions between DNA and fuchsin basic（FB）. FB has an irreversible electro-oxidation peak in 5 mmol/L Tris-HCl buffer solution at pH = 7.4 on a glassy carbon electrode（GCE）. After adding certain concentration of dsDNA, the oxidation peak current of FB decreases, but the peak potential hardly changes. The visible absorption spectroscopic study shows that the binding mode of FB to dsDNA is intercalative binding and electrostatic binding when the ratio of the concentration of dsDNA to FB is smaller than 0. 2, and anew substance, which produces a new absorption peak, is obtained via a covalent binding between dsDNA and FB apart from intercalative binding and electrostatic binding when the ratio of the concentration of dsDNA to FB is larger than 0. 2. The visible absorption spectra varies no longer when the ratio of the concentration of dsDNA＇to FB is larger than 1.5. A mean binding ratio of dsDNA to FB was determined to be 1.4： 1, suggesting that two complexes FB-dsDNA and FB-2dsDNA be formed. The interaction between FB and ssDNA was only electrostatic binding. The more powerful interaction of FB with dsDNA than with ssDNA may be applied for the recognition of dsDNA and ssDNA, and in DNA biosensor as hybridization indicator.

Extraordinary adsorption of acidic fuchsine and malachite green onto cheap nano-adsorbent derived from eggshell

Removal of dyestuffs such as Acidic Fuchsine(AF)and Malachite Green(MG)being present in many forms in industries is vital to protect water reservoirs from their catastrophic effects on the ecosystem.This study attempts to effectively eliminate these dyes using a low-cost and eco-friendly material.Eggshell,as a biocompatible by-product,was initially characterized,then some modifications were conducted,and its morphology and chemical structure were then examined through(Atomic force microscopy)AFM,(Fourier-Transform Infrared Spectroscopy)FTIR,(Energy-Dispersive X-ray Spectroscopy)EDS and(Brunauer–Emmett–Teller)BET analyses.They revealed that the modifications on raw material gave rise to a natural nano-adsorbent presenting porous medium appropriate for targeted adsorbate molecules with the average particle size and average pore diameter of 54 and^2 nm,respectively.Functional groups on the adsorbent surface were also of importance to assist the adsorption of AF and MG.The effect of contact time,adsorbent dose,solution p H and initial concentration was evaluated.Pseudo-second order model accurately correlated the experimental kinetic data for both dyes.Moreover,the participation of intra-particle diffusion along with film diffusion in controlling the process was suggested.Langmuir isotherm model fitted very well to the equilibrium data for both dyes and maximum monolayer adsorption capacity of AF and MG was accordingly calculated to be 5000 and 3333.33 mg·g-1 respectively.The inherent characteristics of eggshell make it a potential material to remove contaminants from wastewater in future applications.

Efficient adsorption removal and adsorption mechanism of basic fuchsin by recyclable Fe_(3)O_(4)@CD magnetic microspheres

Excessive discharge of dye wastewater has brought serious harm to human health and the environment.In this paper,a magnetic absorbent,ferroferric oxide@β-cyclodextrin(Fe_(3)O_(4)@CD),was prepared for the efficient adsorption removal of basic fuchsin(BF)from dye wastewater,based on the special amphiphilicity ofβ-CD and the strong magnetism of Fe_(3)O_(4).A series of influence factors including the initial dye concentration,adsorbent dosage,temperature and pH were investigated,as well as the adsorption mechanism.The results show that Fe_(3)O_(4)@CD has the best adsorption and removal effect on BF dye at room temperature and neutral pH,when the initial concentration of dye is 25 mg/L and the adsorbent dosage is 100 mg.The adsorption behavior conforms to the pseudo-second-order kinetics and the Langmuir adsorption isotherm,and the adsorption process is spontaneously endothermic.Fe_(3)O_(4)@CD adsorbed with BF dye can be rapidly separated under an external magnetic field and then easily regenerated by HCl treatment.After 5 times of recycling,the removal rate of the prepared magnetic composite on BF dye is kept above 75%.This work will provide an economic and eco-friendly technology for the treatment of the actual dye wastewater.

Aqueous solution of basic fuchsin as food irradiation dosimeter

Dosimetric characterization of aqueous solution of basic fuchsin was studied spectrophotometrically for possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solu- tions were determined and the decrease in absorbance with the dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λmax (540nm) as well as 510nm and 460 nm. At all these wavelengths, the decrease in absorbance of the dosimeter was linear with respect to the absorbed dose from 50 Gy to 600 Gy. The stability of dosimetric solution during post-irradiation storage in the dark at room temperature showed that after initial bleaching during first ten to twenty days, the response was almost stable for about 34 days. The study on the effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that basic fuchsin dye is photosensitive as well as thermally sensitive.

Adsorption of acid fuchsin onto LTA-type zeolite derived from fly ash

A facile strategy without organic template was developed for the conversion of fly ash to LTA-type zeolite(LTA-Z),which could be used as a good adsorbent for the removal of acid fuchsin(AF).XRD results indicated that the pure crystalline product was obtained with the structure of LTA-type zeolite.SEM investigations showed that the well-defined LTA-Z crystals exhibited uniform size with the same cubic shape.The maximum AF adsorption amount was observed at pH=5,slightly lower than pHPZC of LTA-Z.Higher temperature favored AF adsorption onto LTA-Z and it was an endothermic process.Furthermore,AF adsorption amount increased with initial AF concentration increasing and LTA-Z dosage decreasing.Surface sorption governed this process at the initial 120 min period,followed by the internal diffusion of AF molecules between porous sites.The Langmuir model was determined as the adsorption isothermal,suggesting that the monolayer coverage of AF on LTA-Z surface was involved.

LaCoO_(3)钙钛矿型催化剂的制备及其光催化降解酸性品红和碱性品红的研究

以硝酸钴、硝酸镧及柠檬酸为原料,在水热体系中采用水热合成法合成出一系列的钙钛矿型催化剂LaCoO_(3),考察当焙烧温度不同时,所合成催化剂的物化性质和降解酸性品红和碱性品红的光催化性能,并分析了催化剂降解品红的降解机理.实验结果表明,采用水热合成法能够成功合成出钙钛矿型催化剂LaCoO_(3),随着焙烧温度的升高,催化剂的颗粒尺寸逐渐增大,结晶度则呈现先升高后降低的趋势.与此同时,比表面积、孔径和孔体积则逐渐减小.另外通过光催化降解品红来测试催化剂的光催化性能,结果表明LaCoO_(3)对酸性品红和碱性品红都具有很好的光催化活性,但对酸性品红的降解率高于碱性品红,这可能与不同品红的结构或者溶液的酸碱性有关.

乳酸酚棉兰染色在气传花粉鉴定中的应用

目的探索乳酸酚棉兰(lactophenol cotton blue,LPCB)染色方法在气传花粉镜检中的潜在应用价值。方法分别采用碱性复红(basic fuchsin,BF)染色与LPCB染色鉴定潍坊市春季、夏秋季主要气传花粉并记录每日花粉粒数。结果在鉴定构树花粉、悬铃木属花粉、蒿属花粉、苋科花粉和禾本科花粉方面,LPCB染色较BF染色更具优势,而在鉴定柏科花粉方面,BF染色更具优势。此外,潍坊市夏秋季优势花粉近40年无明显变化,由于绿化树种的改变,悬铃木属花粉已成为本地春季的主要致敏花粉。结论LPCB染色可同时用于真菌和气传花粉的鉴定,在保证鉴定准确性的同时,节约时间成本。

UiO-66/γ-Al_(2)O_(3)催化剂制备及其处理模拟公路污水的研究

公路废水含有许多有机大分子污染物,如果直接排放将会对环境造成巨大的危害。为此,采用水热合成法,以ZrCl_(4)作为金属离子源,以对苯二甲酸作为有机配位体,以N΄N-二甲基酰胺溶液为溶剂,制备了金属有机骨架材料UiO-66,然后采用原位生长法制备了UiO-66/γ-Al_(2)O_(3)复合材料,用于处理模拟公路污水。通过X-射线衍射仪(XRD),扫描电镜(SEM),能谱仪(EDS),傅里叶红外光谱仪(FT-IR),热重分析仪(TG)等方法对UiO-66/γ-Al_(2)O_(3)复合材料进行了表征,主要考察了其处理酸性品红模拟公路污水与处理实际公路污水的催化降解效果。分析了催化剂加入量、反应时间、酸性品红溶液初始质量浓度、酸性品红溶液初始体积等因素对催化过程的影响。结果显示,UiO-66/γ-Al_(2)O_(3)去除酸性品红的最佳条件为:UiO-66/γ-Al_(2)O_(3)加入量为1.00 g,催化反应时长为1 h,酸性品红初始质量浓度为40 mg/L,初始体积为50 mL。在此条件下酸性品红的去除率为97.52%,实际公路污水中污染物的去除率为40.63%。

Fe^(3+)掺杂Bi_(3)NbO_(7)催化剂可见光降解碱性品红

采用共沉淀法制备了Fe^(3+)掺杂Bi_(3)NbO_(7)催化剂,并利用XRD、SEM、TEM和BET对制备的样品进行表征.结果表明:制备的Fe^(3+)掺杂Bi_(3)NbO_(7)晶相单一,Fe^(3+)进入了Bi_(3)NbO_(7)的晶格,呈现四方体和片状两种形状.可见光下对碱性品红染料降解测试结果显示:在碱性品红质量浓度为5 mg/L、催化剂添加量为1 g/L的条件下,光照240 min后碱性品红的降解率达到94.7%.光催化反应过程中,·OH和·O_(2)^(-)是主要的活性基团,反应过程中吸附起到一定的影响.Fe^(3+)掺杂Bi_(3)NbO_(7)含有一定量的氧空位,有利于提高光催化活性.

负载TiO_2凹凸棒石光催化氧化法处理酸性品红染料废水

以凹凸棒石粉末负载TiO2为催化剂对染料废水进行光催化氧化实验,研究了催化剂的投加量、光照时间以及起始浓度对酸性品红染料废水光降解作用的影响。结果表明:负载TiO2凹凸棒石催化剂与纯TiO2粉末相比具有更高的光催化活性,负载催化剂投加量在0.25g/L时,光催化效果最好。催化反应在很短时间内即能达到较高的去除率,3h后的平均去除率均可达95%。

聚碱性品红修饰电极的制备及应用

研究了碱性品红在玻碳电极上聚合的最佳实验条件及其聚合机理，发现该修饰电极对多巴胺具有良好的催化作用，能大大提高多巴胺在玻碳电极上的响应，在pH=7.0的磷酸盐缓冲溶液中，用该修饰电极测定多巴腔的线性范围为2×10－7～1×10－5mol／L，检测限为1×10－7mol／L，并且具有稳定性好、响应快、选择性高等特点．

Pr掺杂TiO2光催化剂的制备及其对酸性品红降解反应的催化性能

以钛酸四丁酯为前躯物,采用溶胶-凝胶法制备了掺杂不同含量Pr的TiO2光催化剂,利用XRD,TG-DTA,AFM,UV-Vis,FTIR等手段对催化剂进行了表征。并通过酸性品红光催化降解实验对其光催化性能进行了评价,考查了实验条件,如催化剂用量,烧结温度,掺杂量等对催化剂催化活性的影响。Pr2O3的掺杂阻碍了TiO2晶相由锐钛矿型向金红石型的转变,使TiO2的粒径减小,比表面积增大,催化活性增强。当Pr掺杂量为0.8%,催化剂用量为0.03g,烧结温度为500℃时,酸性品红的降解率达到97%以上,酸性品红的降解反应为准一级反应。

枣核对水溶液中亚甲基蓝、碱性品红的吸附性能研究

首次采用枣核作为生物吸附剂,对模拟废水中的亚甲基蓝和碱性品红进行吸附性能研究。基于单因素实验考察了吸附剂粒径、吸附剂用量、吸附时间、p H以及染料初始浓度等因素对水溶液中亚甲基蓝和碱性品红吸附效果的影响,并通过吸附等温线、吸附动力学和热力学研究来探讨吸附机理。结果表明,枣核能够有效去除水中亚甲基蓝和碱性品红,当p H均在6左右,吸附亚甲基蓝、碱性品红枣核投加量分别为8、10g/L,用60目的枣核对50mg/L的两种染料废水处理7h,其去除率均在90%以上。枣核对水溶液中亚甲基蓝、碱性品红染料的吸附是一个自发的吸附过程,其吸附行为均符合二级反应速率方程和Langmuir、Freundlich吸附等温式。经计算得出枣核对亚甲基蓝的饱和吸附量为22.94mg/g,对碱性品红的饱和吸附量为23.92mg/g。研究结果表明枣核是一种很有前景的阳离子染料废水处理生物材料。

Ag-BiVO_4催化剂的制备及其可见光催化活性

以Bi2O3和V2O5为原料,通过高温固相反应合成BiVO4;并采用浸渍法对BiVO4进行Ag掺杂,制备具有较好可见光催化活性的Ag-BiVO4。采用X射线衍射仪、紫外-可见分光光度仪、比表面分析仪对所制得的Ag-BiVO4进行了表征。实验结果表明:Ag掺杂不会引起BiVO4的晶型变化,可提高其对可见光的吸光性能;在Ag掺杂量为4%、溶液pH为7.0、Ag-BiVO4加入量为7g/L的条件下,光催化反应6min后碱性品红的脱色率最高,可达90%以上。

球形Bi4Ti3O12制备及其可见光催化性能

采用水热法合成球形钛酸铋复合氧化物光催化剂,利用SEM、XRD和UV-Vis DRS等表征手段对复合氧化物的晶体结构、微观形貌和光学性能进行了分析,结果表明,制备的钛酸铋复合氧化物为10 nm的球形颗粒,具有良好的晶型结构,禁带宽度为2.7 nm,有较好的可见光吸收能力。以亚甲基蓝、甲基橙及酸性品红为目标污染物,研究了复合氧化物在可见光下的光催化降解有机污染物的性能,并对光催化降解机理进行了探讨。结果表明,在可见光照射下,该复合氧化物对酸性品红降解效果明显优于亚甲基蓝和甲基橙,光照150 min下,降解率可达91%。

稻壳与脱硅稻壳活性炭特性及对有机物吸附

以稻壳为原料,同时制备脱硅稻壳,采用ZnCl2-CuCl2复合活化剂制备活性炭,并对所制备的稻壳活性炭(RAC)与脱硅稻壳活性炭(FAC)的孔结构和表面化学性质进行了分析,而后将其应用于对水中有机物的去除,同时研究了其吸附特性。结果表明:所制得的稻壳活性炭比表面积达到了1 924 m2/g,而稻壳经过脱硅处理制得的活性炭比表面积达到了2 433 m2/g。脱硅稻壳表面具有更多种类的官能团存在。稻壳与脱硅稻壳活性炭在碱性条件下有利于品红的吸附,并且适用于高盐度条件下品红的吸附;在初始pH值为7,初始质量浓度为400 mg/L,投加量为0.8 mg/g时,稻壳活性炭和脱硅稻壳活性炭对有机物的吸附量分别达到439和483 mg/g;吸附等温模型符合Langmuir等温式;吸附动力学以及脱附研究显示稻壳与脱硅稻壳活性炭对品红的吸附过程主要由化学吸附控制。

酸性品红共振光散射法测定蛋白质

本文研究了酸性品红 (FA)与蛋白质相互作用所引起的共振光散射 (RLS)光谱 ,在pH 1 88～ 4 4 8范围内 ,加入蛋白质导致酸性品红 (FA)共振光散射增强 ,在 340nm处 ,存在一共振光散射增强峰 ,其散射光强度增加值与蛋白质的浓度呈线性关系 ,据此建立了一种测定蛋白质的共振散射法。方法的线性范围为 0～ 2 5mg·L- 1 ,检出限 0 0 2 3mg·L- 1 。该方法用于人尿样和血样的测定 ,与医院提供结果相符 ,且具有更高的灵敏度。

镍网负载纳米TiO_2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明:UV灯+镍网+TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。