Laboratory pull-out tests on fully grouted rock bolts and cable bolts:Results and lessons learned

Laboratory pull-out tests were conducted on the following rock bolts and cable bolts:steel rebars,smooth steel bars,fiberglass reinforced polymer threaded bolts,flexible cable bolts,IR5/IN special cable bolts and Mini-cage cable bolts.The diameter of the tested bolts was between 16 mm and 26 mm.The bolts were grouted in a sandstone sample using resin or cement grouts.The tests were conducted under either constant radial stiffness or constant confining pressure boundary conditions applied on the outer surface of the rock sample.In most tests,the rate of displacement was about 0.02 mm/s.The tests were performed using a pull-out bench that allows testing a wide range of parameters.This paper provides an extensive database of laboratory pull-out test results and confirms the influence of the confining pressure and the embedment length on the pull-out response(rock bolts and cable bolts).It also highlights the sensitivity of the results to the operating conditions and to the behavior of the sample as a whole,which cannot be neglected when the test results are used to assess the bolt-grout or the grouterock interface.

Development and application of an interface constitutive model for fully grouted rock-bolts and cable-bolts

This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By means of a comprehensive framework,a Coulomb-type failure criterion accounting for friction mobilization was defined.During the elastic phase,in which the interface joint is not yet created,the proposed model provides zero radial displacement,and once the interface joint is created,interface dilatancy is modeled using a non-associated plastic potential inspired from the behavior of rock joints.The results predicted by the proposed model are in good agreement with experimental results.The model has been implemented in a finite element method(FEM)code and numerical simulations have been performed at the elementary and the structural scales.The results obtained provide confidence in the ability of the new model to assist in the design and optimization of bolting patterns.

Utilizing a novel fiber optic technology to capture the axial responses of fully grouted rock bolts

Rock bolts are one of the primary support systems utilized in underground excavations within the civil and mining engineering industries. Rock bolts support the weakened rock mass adjacent to the opening of an excavation by fastening to the more stable, undisturbed formations further from the excavation. The overall response of such a support element has been determined under varying loading conditions in the laboratory and in situ experiments in the past four decades; however, due to the limitations with conventional monitoring methods of capturing strain, there still exists a gap in knowledge associated with an understanding of the geomechanical responses of rock bolts at the microscale. In this paper, we try to address this current gap in scientific knowledge by utilizing a newly developed distributed optical strain sensing(DOS) technology that provides an exceptional spatial resolution of 0.65 mm to capture the strain along the rock bolt. This DOS technology utilizes Rayleigh optical frequency domain reflectometry(ROFDR) which provides unprecedented insight into various mechanisms associated with axially loaded rebar specimens of different embedment lengths, grouting materials, borehole annulus conditions, and borehole diameters. The embedment length of the specimens was found to be the factor that significantly affected the loading of the rebar. The critical embedment length for the fully grouted rock bolts(FGRBs) was systematically determined to be430 mm. The results herein highlight the effects of the variation of these individual parameters on the geomechanical responses FGRBs.

A local homogenization approach for simulating the reinforcement effect of the fully grouted bolt in deep underground openings

Fully grouted bolts are a key component of the support system for underground openings.Although considerable effort has been made in the simulation of the reinforcement effect of the fully grouted bolts on the rock masses surrounding underground openings,most of the work has limited significance since the structural element approach is used.This study proposes a local homogenization approach(L-H approach)that integrates elastoplastic mechanics,composite mechanics,and analytical approaches with numerical simulation to effectively simulate the reinforcement effect of the fully grouted bolt on deep surrounding rock masses.In the L-H approach,the representative volume of bolted rock mass(RVBRM)with a fully grouted bolt is established based on the original mesh model utilized in the rockbolt element approach.The RVBRM is a regular quadrangular prism with a cross-sectional size equal to the bolt spacing and a length equal to the bolt length.The RVBRM is homogenized by the L-H approach from a unidirectional bolt-reinforced composite into a homogeneous transversely isotropic medium whose mechanical properties are described by a new transversely isotropic elastoplastic model.The L-H parameters for the RVBRM are obtained using analytical approaches,composite mechanics,and known parameters of the rock mass and bolt.Using the L-H approach,the reinforcement effect of the fully grouted bolt on the bolted rock specimen and the surrounding rock mass in Jinping II Diversion Tunnel#2 with a depth greater than 2000 m is simulated.The results show that the predictions of the L-H approach are more in agreement with the physical model results of bolted rock specimen and provide a more realistic response of the bolted surrounding rock mass.The L-H approach demonstrates that fully grouted bolts with common bolt spacings and diameters substantially enhance the elastic modulus,shear strength,and tensile strength of the rock mass in the direction of the bolt axis.

Stress evolution and support mechanism of a bolt anchored in a rock mass with a weak interlayer

By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instrumented five pairs of symmetrical strain gauges. The experimental results show that the fully grouted bolt suffers tensile, compressive, bending and shear stress at the same time. The bolt stress evolution is closely related to the deformation stages of the rock mass which are very gradually varying stage, gradually varying stage at the pre-peak and suddenly varying stage at the post peak stage.The axial compressive stress in the bolt is mainly induced by the moment. Thus, in most cases the axial compressive stress is distributed on one side of the bolt. For axial stresses, induced by the axial force and the bending moment at the post-peak stage, three types of changing are observed, viz. increasingincreasing type, decreasing-increasing type and increasing-decreasing type. The stress characteristics of the bolt section in the weak interlayer are significantly different from those in the hard rock. The failure models of the anchored bolt are tensile failure and shear failure, respectively. The bolt not only provides constraints on the free surface of the rock mass, but also resists the axial and lateral loading by the bending moment. This study provides valuable guidelines for bolting support design and its safety assessment.