Neural Network Identification Model for Technology Selection of Fully-Mechanized Top-Coal Caving Mining

This paper mainly discusses the selection of the technical parameters of fully mechanized top coal caving mining using the neural network technique. The comparison between computing results and experiment data shows that the set up neural network model has high accuracy and decision making benefit.

Effects of caving–mining ratio on the coal and waste rocks gangue flows and the amount of cyclically caved coal in fully mechanized mining of super-thick coal seams

Aimed at determining the appropriate caving–mining ratio for fully mechanized mining of 20 m thick coal seam, this research investigated the effects of caving–mining ratio on the flow fields of coal and waste rocks, amount of cyclically caved coal and top coal loss by means of numerical modeling. The research was based on the geological conditions of panel 8102 in Tashan coal mine. The results indicated the loose coal and waste rocks formed an elliptical zone around the drawpoint. The ellipse enlarged with decreasing caving–mining ratio. And its long axis inclined to the gob gradually became vertical and facilitating the caving and recovery of top coal. The top coal loss showed a cyclical variation; and the loss cycle was shortened with the decreasing in caving–mining ratio. Moreover, the mean squared error(MSE) of the amount of cyclically caved coal went up with increasing caving–mining ratio, indicating a growing imbalance of amount of cyclically caved coal, which could impede the coordinated mining and caving operations. Finally it was found that a caving–mining ratio of 1:2.51 should be reasonable for the conditions.

Back-and-forth mining for hard and thick coal seams—research about the mining technology for fully mechanized caving working face of Datong Mine

The article introduced the key technology, mining process, and back-and-forth mining method for the caving working face of hard-thick coal seams in Datong mine, and researched this innovations process, optimized the systemic design and working face out-play, tried to perfect the caving mining technology of hard-thick coal seams further.

Development and prospect on fully mechanized mining in Chinese coal mines

Fully mechanized mining(FMM)technology has been applied in Chinese coal mines for more than 40 years.At present,the output of a FMM face has reached 10-million tons with Chinese-made equipment.In this study,the new developments in FMM technology and equipment in Chinese coal mines during past decades are introduced.The automatic FMM technology for thin seams,complete sets of FMM technology with ultra large shear height of 7 m for thick seams,complete sets of fully mechanized top coal caving technology with large shear height for ultra-thick seams of 20 m,complete sets of FMM technology for complex and difficult seams,including steeply inclined seams,soft coal seams with large inclination angle,and the mechanized filling mining technology and equipment are presented.Some typical case studies are also introduced.Finally,the existing problems with the FMM technology are discussed,and prospect of FMM technology and equipment applied in Chinese coal mines is put forward.

Theoretical description of drawing body shape in an inclined seam with longwall top coal caving mining

Understanding the characteristics of drawing body shape is essential for optimization of drawing parameters in longwall top coal caving mining.In this study,both physical experiments and theoretical analysis are employed to investigate these characteristics and derive a theoretical equation for the drawing body shape along the working face in an inclined seam.By analyzing the initial positions of drawn marked particles,the characteristics of the drawing body shape for different seam dip angles are obtained.It is shown that the drawing body of the top coal exhibits a shape-difference and volume-symmetry characteristic,on taking a vertical line through the center of support opening as the axis of symmetry,the shapes of the drawing body on the two sides of this axis are clearly different,but their volumes are equal.By establishing theoretical models of the drawing body in the initial drawing stage and the normal drawing stage,a theoretical equation for the drawing body in an inclined seam is proposed,which can accurately describe the characteristics of the drawing body shape.The shape characteristics and volume symmetry of the drawing body are further analyzed by comparing the results of theoretical calculations and numerical simulations.It is shown that one side of the drawing body is divided into two parts by an inflection point,with the lower part being a variation development area.This variation development area increases gradually with increasing seam dip angle,resulting in an asymmetry of the drawing body shape.However,the volume symmetry coefficient fluctuates around 1 for all values of the seam dip angle variation,and the volumes of the drawing body on the two sides are more or less equal as the variation development volume is more or less equal to the cut volume.Both theoretical calculations and numerical simulations confirm that the drawing body of the top coal exhibits the shape-difference and volume-symmetry characteristic.

Top coal caving mining technique in thick coal seam beneath the earth dam

It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.

Technical parameters of drawing and coal-gangue field movements of a fully mechanized large mining height top coal caving working face

Under fully mechanized, large mining height top coal caving conditions, the shield beam slope angle of the support increases due to the enlargement of the top coal breaking and caving space. This results in a change of the caving window location and dimensions and, therefore, the granular coal-gangue movement and flows provide new characteristics during top coal caving. The main inferences we draw are as follows. Firstly, after shifting the supports, the caved top coal layer line and the coal gangue boundary line become steeper and are clearly larger than those under common mining heights. Secondly, during the top coal caving procedure, the speed of the coal-gangue flow increases and at the same drawing interval, the distance between the coal-gangue boundary line and the top beam end is reduced. Thirdly, affected by the drawing ratio, the slope angle of the shield beam and the dimensions of the caving window, it is easy to mix the gangue. A rational drawing interval will cause the coal-gangue boundary line to be slightly behind the down tail boom lower boundary. This rational drawing interval under conditions of large mining heights has been analyzed and determined.

Trial of small gateroad pillar in top coal caving longwall mining of large mining height

Coal seams in Tashan Mine of Datong Coal Group in China average 15 m thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 3.8 m and the top coal caving height was 11.2 m. The gateroad pillar between panels was 38 m. During retreat mining,serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore,pillarless mining was experimented. Using numerical modeling and comparative study of cases of similar mining condition,it was decided to employ a 6 m wide pillar,rather than the previous 38 m wide pillar.Support system for the gateroads was designed and implemented. During gateroad development,pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion. Since the development of gateroad has just completed,and retreat mining has not begun,the effectiveness of the proposed methods is unknown at this point. However,monitoring will continue until after mining.The results will be published in a separate paper.

Analysis and key control technologies to prevent spontaneous coal combustion occurring at a fully mechanized caving face with large obliquity in deep mines

In order to prevent spontaneous coal combustion occurring at a fully mechanized caving face with large obliquity in deep mines in China,we have analyzed the characteristics of spontaneous coal combustion and explain theoretically the factors affecting spontaneous coal combustion,such as rock bursts,high temperatures,high ventilation resistance,slow advancing speed and large obliquity mining.Key technologies to prevent spontaneous combustion occurring in sharply inclined seams in deep mines are proposed;these include pouring water,stopping leakage in upper and lower corners of the working face,choking off the goaf and covering the coal.CO concentrations were controlled within two years to less than 15×10-6 at the upper corner by applying these technologies at the 1410 working face of the Huafeng coal mine.Our method has significant theoretical value and is of practical importance in controlling spontaneous coal combustion occurring at a fully mechanized caving face with large obliquity in deep mines.

Surface Movement Regularity of Super-Wide Mining Face With Top-Coal Caving

No.4326 super-wide panel of Wangzhuang Coal Mine ( in which the fully-mechanized top-coal caving longwall mining method was used) was monitored for dynamic characteristic of surface movement. The dynamic surface movement in and after mining was predicted by using the Mining Subsidence Prediction System. The results indicate that after mining, the surface above the super-wide panel reaches a state of full subsidence, making the No.309 national highway above the panel be located on the flat bottom of the subsidence basin so that the influence of mining activity in both sides of 4326 panel on the national highway is the smallest.

Analysis on air-leakage law of goaf in condition of ascending mining for top-coal caving

Using the Jisan Coalmine's top-coal caving for the 3down coal seam with ascending mining as the project background, the air-leakage characteristics of the goaf wasanalyzed. Through data fitting of the in situ observation, the models of gas seepage, diffusion and air-leakage in the goaf were established in ascending mining. The ComputationFluid Dynamics software Fluent was used to simulate the air-leakage law of the goaf. Theresults of the numerical simulation provide a basis for the use of the technology of ventilation and fire prevention in the working face of an ascending mining, which ensures thesafety in production in the working face of the top-coal caving for 3_down coal seam in theJisan Coalmine.

Coupling effects of coal pillars of thick coal seams in large-space stopes and hard stratum on mine pressure

Concerning the issue of mine pressure behaviors occurred in fully mechanized caving mining of thick coal seams beneath hard stratum in Datong Mining Area, combined with thin and thick plate theory, the paper utilizes theoretical analysis, similar experiments, numerical simulations and field tests to study the influence of remaining coal pillars in Jurassic system goaf on hard stratum fractures, as well as mine pressure behaviors under their coupling effects. The paper concludes the solution formula of initial fault displacement in hard stratum caused by remaining coal pillars. Experiments prove that coupling effects can enhance mine pressure behaviors on working faces. When inter-layer inferior key strata fractures, mine pressure phenomenon such as significant roof weighting steps and increasing resistance in support.When inter-layer superior key strata fractures, the scope of overlying strata extends to Jurassic system goaf, dual-system stopes cut through, and remaining coal pillars lose stability. As a result, the bottom inferior key strata also lose stability. It causes huge impacts on working face, and the second mine pressure behaviors. These phenomena provide evidence for research on other similar mine strata pressure behaviors occurred in dual-system mines with remaining coal pillars.

Systematic principles of surrounding rock control in longwall mining within thick coal seams

Effective surrounding rock control is a prerequisite for realizing safe mining in underground coal mines.In the past three decades, longwall top-coal caving mining(LTCC) and single pass large height longwall mining(SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increases the difficulty in ground control.Longwall face failure is a common problem in both LTCC and SPLL mining. Such failure is conventionally attributed to low strength and high fracture intensity of the coal seam. However, the stiffness of main components included in the surrounding rock system also greatly influences longwall face stability.Correspondingly, surrounding rock system is developed for LTCC and SPLL faces in this paper. The conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between the ultimate bearing capacity and actual load imposed on the coal wall.The influences provided by coal strength, coal stiffness, roof stiffness, and hydraulic support stiffness,as well as the movement of roof structure are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.

Fracturing,caving propagation and influence of mining on groundwater above longwall panels–a review of predictive models

Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining.The motivation for suchmodels varies,ranging fromunderstanding the impact ofmining on surface subsidence,to back-analysis of caving behaviour in the immediate roof behind the longwall face.One of the most critical motivating factors that is taking on increased importance in many coalfields,is the need for better understanding,and hence prediction of the impact of mining on overlying strata,particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the southern coalfields of New South Wales,south of Sydney.The paper discusses the parameter often referred to as"height of fracturing"in terms of the critical parameters that influence it,and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact.The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used.The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.

Numerical investigation on the caving mechanism with different standard deviations of top coal block size in LTCC

The size distribution of the broken top coal blocks is an important factor,affecting the recovery ratio and the efficiency of drawing top coal in longwall top coal caving(LTCC)mining panel.The standard deviation of top coal block size(dt)is one of the main parameters to reflect the size distribution of top coal.To find the effect of dt on the caving mechanism,this study simulates experiments with 9 different dt by using discrete element software PFC.The dt is divided into two stages:uniform distribution stage(UDS)whose dt is less than 0.1(Schemes 1–5),and nonuniform distribution stage(NDS)whose dt is more than 0.1(Schemes 6–9).This research mainly investigates the variation of recovery ratio,drawing body shape,boundary of top coal,and contact force between particles in the two stages,respectively.The results showed that with the increasing dt,the recovery ratio of the panel increases first and then decreases in UDS.It is the largest in Scheme 3,which mainly increases the drawing volume at the side of starting drawing end.However,the recovery ratio decreases first and then increases quickly in NDS,and it is the largest in Scheme 9,where the drawing volume at the side of finishing drawing end are relatively higher.In UDS,the major size of top coal is basically medium,while in NDS,the size varies from medium to small,and then to large,with a distinct difference in shape and volume of the drawing body.When the major size of top coal is medium and small,the cross-section width of the initial boundary of top coal at each height is relatively small.Conversely,when the top coal size is large,the initial boundary of top coal has a larger opening range,the rotating angle of lower boundary is relatively small in the normal drawing stage,which is conducive to the development of drawing body and reduces the residual top coal,and the maximum particle velocity and the particles movement angle are both larger.This study lays a foundation for the prediction of recovery ratio,and suggests that the uniform top coal is more manageable and has a larger recovery ratio.

Ground pressure and overlying strata structure for a repeated mining face of residual coal after room and pillar mining

To investigate the abnormal ground pressures and roof control problem in fully mechanized repeated mining of residual coal after room and pillar mining,the roof fracture structural model and mechanical model were developed using numerical simulation and theoretical analysis.The roof fracture characteristics of a repeated mining face were revealed and the ground pressure law and roof supporting conditions of the repeated mining face were obtained.The results indicate that when the repeated mining face passes the residual pillars,the sudden instability causes fracturing in the main roof above the old goaf and forms an extra-large rock block above the mining face.A relatively stable ‘‘Voussoir beam" structure is formed after the advance fracturing of the main roof.When the repeated mining face passes the old goaf,as the large rock block revolves and touches gangue,the rock block will break secondarily under overburden rock loads.An example calculation was performed involving an integrated mine in Shanxi province,results showed that minimum working resistance values of support determined to be reasonable were respectively 11,412 kN and 10,743 kN when repeated mining face passed through residual pillar and goaf.On-site ground pressure monitoring results indicated that the mechanical model and support resistance calculation were reasonable.

Analysis of the dialectical relation between top coal caving and coal-gas outbtu rst

According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by simulating the change of stressstates in the process of top coal initial caving with different mining and caving ratios basedon the ANSYS10.0.The variation of elastic energy and methane expansion energy duringfirst top coal caving was analyzed by first weighting and periodic weighting and combiningwith coal stress and deformation distribution of top coal normal stoping as well as positiveand negative examples in top coal caving of outburst coal seam.The research shows thatthe outburst risk increases along with the increase of the caving ratio in the initial miningstage.In the period of normal stoping,when the mining and caving ratio is smaller than1:3 and hard and massive overlying strata do not exist (periodic weighting is not obvious),it is beneficial to control ground stress leading type outburst.Thus,it is unreasonable toprohibit top coal caving in dangerous and outburst prone areas.

Fracture mechanics model of fully mechanized top coal caving of shallow coal seams and its application

Based on break characteristics of roofs in fully mechanized top-coal mining of thick shallow coal seams, a fracture mechanics model was built, and the criterion of crack propagation in the main roof was derived using the fracture mechanics theory. The relationships between the fracture length of the roof and the working resistance of the supports were discovered, and the correlations between the load on the overlying strata and the ratio of the crack's length to the thickness of the roof were obtained. Using a working face of Jindi Coal Mine, Xing county Shanxi province as an example, the relationships between the fracture length of the roof and the working resistance of the supports were analysed in detail. The results give a design basis in hydraulic top coal caving supports, which could provide useful references in the practical application. On-site experiment proves that the periodic weighting step interval of the caving face is 15–16 m, which is basically consistent with the theoretical analysis results, and indicates that the mechanized caving hydraulic support is capable of meeting the support requirements in the mining of a super-thick but shallowly buried coal seam.