Effect of Different Silica Fumes on Properties of Al_(2)O_(3)-SiC-C Castables for Iron Trough

In order to improve the performance of Al_(2)O_(3)-SiC-C castables for iron trough,samples were prepared using brown corundum,dense corundum,activated alumina micropowder,ball pitch,and silicon as main raw materials,calcium aluminate cement as the binder.Several kinds of silica fumes(93SiO_(2),96SiO_(2),and 99SiO_(2))with different particle size distributions and chemical composition were added to research the effects on the properties of castables.The results show that the sample with 99SiO_(2) fume has high water requirement for molding,but the bulk density is the lowest,the apparent porosity is the highest,the oxidation resistance is the worst,and the permanent linear change on heating is low after firing at 1 450 ℃ for 3 h.The bulk density and the apparent porosity of the sample with 93SiO_(2) fume or 96SiO_(2) fume are equivalent,the hot modulus of rupture of the sample with 93SiO_(2) fume is the lowest,and the slag resistance of the sample with 96SiO_(2) fume is the best.The comprehensive performance of the sample with 96SiO_(2) fume is the best.

Modeling Tensile Strength of Concrete on Partial Replacement of Ce­ment and Sand with Quarry Dust Ground Granulated Blast Furnace and Slag Silica Fumes

Tensile strength of concrete were examined on its partial replacement of cement and sand using ground granulated blast furnace and quarry dust.The study examines its behaviour at different dimensions.This is to monitor the variation effect of these parameters on the growth rates of tensile to the optimum curing age.These include non linear conditions of tensile state,non-elastic and its brittle behaviour at all times as it express zero conditions in tension.This means that it has the ability to with stand pull force.It also reflects its weak ability to handle shear stress thus tends to cause deformation in material as it has poor elasticity.The reflection of its brittle influence the rate of tensile behaviour from concrete ductility.These are known to be a material on modern mechanics of concrete.These are also considered as quasi brittle material.This behaviour was reflected as the system considered evaluating the growth rate of tensile strength that replaced cement and sand with these locally sourced addictives.The developed model monitor other reflected influential parameters such as variation of concrete porosity due it compaction in placements,tensile behaviour reflects these effect that subject it to mechanical properties of concrete.The study expressed the reaction of these parameters in the simulation,the evaluation of these affected the details variation of tensile growth rate at different water cement ratios and curing age.The tensile behaviour that was monitored are based on these factors in the study.The derived model were validated with the a researcher results[24],and both parameters developed best fits correlation.The study is imperative because the system expressed the behaviour of tensile strength from concrete at different dimensions.Experts can applied these concept to monitor tensile behaviour considering these parameters in its growth rates.

Too many exhaust fumes?

Leo and Sam exited and locked the car in a hurry,forgetting to remove the key which was in theignition.Realizing the mistake,Leo asked,“Why don t we get a coat hanger to open it.”“No,that won t work,”answered Sam.“People will think we re trying to break in.”So Leosuggested,“What if we use a pocket knife to cut around the rubber,then stick a finger in and pull

Characterization of time-and size-dependent particle emissions and decay from cooking oil fumes in residence:Impacts of various intervention measures

The dynamic characteristics of cooking-related particle size distributions in real-world settings are not fully understood.Through a real-world campaign in a naturally-ventilated apartment in the northwest US,this study investigates the temporal profiles of size-resolved particle number concentrations(PNCs)ranging from 0.3 to 10µm from frying cooking activities.The cooking scenarios included various combinations of window ventilation,venting range hood(VRH)use,and portable air cleaner(PAC)utilization.Following a standardized pan-frying protocol throughout seven scenarios,real-time PNCs of 16-size bins were measured in the kitchen.The PNCs were empirically compared among size bins,periods,and scenarios.The most abundant size ranges of cooking-related particles were 0.3–0.579µm in number(45%–71%of the total)and 2.685–5.182µm in mass(48%–57%of the total).Compared with the scenario without any cooking-fume mitigating measures,keeping the kitchen windows open reduced the mean PNCs during and within 1-h after cooking for PM_(0.3-2.5),PM_(2.5-10),and PM_(0.3-10)by 78%,92%,and 79%,respectively.By contrast,utilizing a VRH during cooking reduced the corresponding levels by 21%,69%,and 25%,respectively.Combined with running the VRH,using a PAC in the kitchen led to additional reductions of 84%,88%,and 84%,respectively.Additionally,the removal efficiencies of the three strategies generally increased with particle sizes.

Recent research in mechanical properties of geopolymer-based ultrahigh-performance concrete:A review

Due to the growing need for sustainable and ultra-high-strength construction materials,scientists have created an innovative ultra-high-performance concrete called Geopolymer based ultra-highperformance concrete(GUHPC).Besides,in the last few decades,there have been a lot of explosions and ballistic attacks around the world,which have killed many civilians and fighters in border areas.In this context,this article reviews the fresh state and mechanical properties of GUHPC.Firstly,the ingredients of GUHPC and fresh properties such as setting time and flowability are briefly covered.Secondly,the review of compressive strength,flexure strength,tensile strength and modulus of elasticity of fibrous GUHPC.Thirdly,the blast and projectile impact resistance performance was reviewed.Finally,the microstructural characteristics were reviewed using the scanning electron microscope and X-ray Powder Diffraction.The review outcome reveals that the mechanical properties were increased when 30%silica fume was added to a higher dose of steel fibre to improve the microstructure of GUHPC.It is hypothesized that the brittleness of GUHPC was mitigated by adding 1.5%steel fibre reinforcement,which played a role in the decrease of contact explosion cratering and spalling.Removing the need for cement in GUHPC was a key factor in the review,indicating a promising potential for lowering carbon emissions.However,GUHPC research is still in its early stages,so more study is required before its full potential can be utilized.

Green synthesis of ZSM-5 using silica fume and catalytic co-cracking of lignin and plastics for production of monocyclic aromatics

ZSM-5 with hierarchical pore structure was synthesized by a simple two-step hydrothermal crystallization from silica fume without using any organic ammonium templates.The synthesized ZSM-5 were oval shaped particles with a particle size about 2.0 μm and weak acid-dominated with proper Brønsted(B)and Lewis(L)acid sites.The ZSM-5 was used for catalytic co-cracking of n-octane and guaiacol,lowdensity polyethylene(LDPE)and alkali lignin(AL)to enhance the production of benzene,toluene,ethylbenzene and xylene(BTEX).The most significant synergistic effect occurred at n-octane/guaiacol at 1:1 and LDPE/AL at 1:3,under the condition,the achieved BTEX selectivity were 24%and 33%(mass)higher than the calculated values(weighted average).The highest BTEX selectivity reached 88.5%,which was 3.7%and 54.2%higher than those from individual cracking LDPE and AL.The synthesized ZSM-5 exhibited superior catalytic performance compared to the commercial ZSM-5,indicating potential application prospect.

On the Combination of Silica Fume and Ceramic Waste for the Sustainable Production of Mortar

The combined use of silica fume(SF)and ceramic waste(CW)for the production of mortar is studied.Sand is replaced by 5%,10%,15%and 20%of CW while a fixed 5%percentage(%wt of cement)of SF is used.The results show that the best results are obtained by using silica fume and ceramic waste sand with 15%weight of sand and 5%wt of cement.With the addition of sand ceramic waste(SCW),the mortar compressive strength and density increase,while the porosity displays an opposite trend.The experimental analysis is complemented with theoretical considerations on the matrix strength and related improvements in mechanical behavior.It is shown that the agreement between the experimental values and the estimated values is good.

Enhancing Concrete Properties Using Silica Fume:Optimized Mix Design

In the current work concrete mixes containing(7.0-33.11)weight%silica fume as fractional substitution of cement with water/cement ratio(0.42-0.48)were formulated conferring to an implemented two factorial central composite design.The samples were water cured for 7,28,56,and 90 days.The samples were tested for compressive strength and density.The experimental results approved that compressive strength and density increase with age and with rising silica fume content up to 11.9 wt.%.Response surface analysis results for samples cured for 28 days confirmed that silica fume concrete with developed compressive strength(53.42 MPa)could be prepared by incorporation of 11.9 wt.%silica fume as a substituent for cement using a 0.42 water/cement ratio.An intensification in compressive strength and density(up to 39.3%and 2.6%)respectively was recorded for silica fume concrete mixes in contrast to Portland cement concrete.Overall,the research findings revealed that silica fume concretes prepared with appropriate silica fume content and water/cement ratio exhibited superior strength and density features candidate them to be used effectively in civil engineering structural applications.

The anti-obesity effects of EGCG in relation to oxidative stress and air-pollution in China

Modern China,similar to most developing nations,has seen a rise in the prevalence of both obesity and diesel exhaust based air pollution.The cause of obesity is multi-factorial encompassing diet,lifestyle and social factors.Also there has been a reduction in the consumption of fruit,vegetables,and traditional medicinal foods such as polyphenol containing green tea.Replacing these,are high fat and carbohydrate based processed foods which are quickly displacing these wholefoods in the diet.This review paper proposes evidence that a potential cause of obesity is also linked to environmental stress stimuli such as air pollutants,particularly diesel exhaust fumes(DEF)of>2.5μm particulate matter,and discusses a role for a green tea catechin(EGCG)for use as a dietary defence against diet and environmentally induced obesity.China is now at a critical point of a public health pandemic with rising air-borne pollution(via car exhaust fumes DEF),industry pollution such as heavy metals,and the benzene hydrocarbon based‘2PM’particulate matter,now accepted as a major environmental issue for public health.Relevant data published in MEDLINE since 1995 has been gathered to formulate the following review.

三维水墨动画创意与制作新技术——以作品《中国风》为例

为了提高三维水墨动画创意与制作技术水平,以荣获全国二等奖的原创三维水墨动画作品《中国风》为例,介绍了一种三维水墨动画制作新技术:即使用3ds Max软件和Fume FX插件,将建好的三维模型赋予水墨特效,并使用后期特效软件After Effects制作运动镜头效果.与传统制作技术相比,该技术能在运动镜头中更好地表现水墨的晕染和流动感,减少了制作工序,提高了技术含量.

Aircraft Clean Air Requirements Using Bleed Air Systems

There are certification and airworthiness requirements relevant to the provision of clean breathing air in the crew and passenger compartments. There have been continuing reports and studies over the years regarding oil fumes in aircraft, including impaired crew performance. Oil fumes are viewed in varying ways ranging from rare seal bearing failures, to low level leakage in normal flight. A Masters of Science (MSc) research degree was undertaken to assess whether there is any gap between the certification requirements for the provision of clean air in crew and passenger compartments, and the theoretical and practical implementation of the requirements using the bleed air system. A comprehensive literature search reviewed applicable certification standards, documented and theoretical understanding of oil leakage. Two types of interviews were conducted to address the research questions. Key aviation regulators were questioned about the process by which they certify and ensure compliance with the clean air requirements. Aerospace engineers and sealing professionals were interviewed about their understanding of how oil may leak past compressor oil bearing seals, and into the air supply under various flight conditions. The outcome of the research showed that there is a gap between the clean air certification requirements, and the theoretical and practical implementation of the requirements using the bleed air system. Low level oil leakage into the aircraft cabin in normal flight operations is a function of the design of the engine lubricating system and bleed air systems, both utilising pressurised air. The use of the bleed air system to supply the regulatory required air quality standards is not being met or being enforced as required.

第一个通过EPA注册的溴甲烷替代物-Eco_2Fume

Eco2 Fume是由 2 %磷化氢和 98%二氧化碳混合而成的熏蒸剂。该熏蒸剂具有操作简单、价格低廉、对环境安全、对使用者安全、可持续药效、不易燃烧、熏蒸后无残渣、无未挥发分解的问题、容易达到和控制浓度、能有效杀灭各种虫态等优点。Eco2 Fume是第一个通过EPA注册的溴甲烷的替代剂。

Prediction of concentration of toxic gases produced by detonation of commercial explosives by thermochemical equilibrium calculations

An adverse effect resulting from explosive mine blasts is the production of toxic nitrogen oxides(NO and NO_(2)) and carbon monoxide(CO).The empirical measurements of the concentration of toxic gases showed that it depends not only on the composition of an explosive and properties of its ingredients but also on several other parameters,such as volume of blasting chamber,explosive charge mass and design,confinement characteristics,surrounding atmosphere,etc.That explains why measured concentrations of toxic gases reported in literature significantly differ.In this paper,we discuss the possibility of theoretical prediction of the concentration of toxic gases by thermochemical equilibrium calculation applying two models:ideal detonation model and deflagration model.It can be demonstrated that thermochemical calculations can provide a good estimation of the measured concentrations and reproduce experimentally obtained effects of additives on the production of toxic gases.It was also found that the ideal detonation model applies to heavily confined explosive charges,while the deflagration model is more suitable for low detonation velocity explosives with light confinement.

聚丙烯中空纤维人工肺纠治呼吸衰竭的实验研究

聚丙烯中空纤维人工肺纠治呼吸衰竭的实验研究天津市肺科医院人工肺研究室丁伟，张向，马景良，叶宏琛聚丙烯中空纤维是七十年代发展起来的一种新型材料。由于其疏水性和良好的血液相容性被广泛应用于人工肺制作。八十年代末，美国将聚丙烯中空纤维置入腔静脉进行血气交换...

Performances of a Bitumen Fume and Condensate Generation System for Sampling Method Development

A laboratory system was designed to generate bitumen fumes and expose tested samplers in a homogenised chamber. The system was also designed to condense the fumes in the form of oil that could be used as a standard for further analytical method development. The laboratory system was evaluated in terms of stability, repeatability, aging, and ranges, focusing on the quality and quantity of the fumes and their physical characteristics. The fumes generated with the laboratory system were also compared to fumes emitted at workplaces to evaluate their similarity. The results demonstrated that laboratory fume generation was stable and repeatable. Humidity ranged from 20% to 80% RH and the total fume concentration ranged from 0.01 to 9.36 mg.m-3, covering the conditions encountered for road paving worksites. The fumes generated in the laboratory were found to be similar to those of workplaces, with slight differences in light compounds equivalent to C12 and below n-alkanes. Thus, the system designed in this study is considered capable of generating bitumen fumes used to develop sampling and analysis methods.

A Comparative Study on the Pozzolanic Activity between Nano-SiO_2 and Silica Fume

The pozzolanic activity of nano-SiO2 and silica fume was comparatirely stndied by X-ray diffraction （ XRD ） , differential scanning calorimetry （DSC）, scanning electron micrascopy （SEM） and the compressive , bond and bending streugths of hardened paste and concrete were also measured. Results indicate that the compressive strength development of the paste made from Ca（OH）2 and nano-SiO2, the reaction rate of Ca（ OH）2 with nano- SiO2 and the velocity of C-S-H gel formation from Ca （ OH）2 with nano-SiO2 showed marked increases over those of Ca（ OH）2 with silica fume. Furthermore, the bond strength at the interface between aggregate and hardened cement paste, and the bending strength of concrete incorporated with 3% .NS increased more than those with SF, especially at early ages. To sum up, the pozzolanic activity of nano-SiO2 was much greater than that of silica fume. The results suggest that with a small amount of nano-SiO2, the Ca（ OH）2 crystal at the interface between hardened cement paste and aggregate at early ages may be effectively absorbed in high performance concrete.

Effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete

The effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete （SCGC） was investigated in this paper. The work focused on the concrete mixes with a fixed water-to-geopolymer solid （W/Gs） ratio of 0.33 by mass and a constant total binder content of 400 kg/m3. The mass fractions of silica fume that replaced fly ash in this research were 0wt%, 5wt%, 10wt%, and 15wt%. The workability-related fresh properties of SCGC were assessed through slump flow, V-funnel, and L-box test methods. Hardened concrete tests were limited to compressive, splitting tensile and flexural strengths, all of which were measured at the age of 1, 7, and 28 d after 48-h oven curing. The results indicate that the addition of silica fume as a partial replacement of fly ash results in the loss of workability; nevertheless, the mechanical properties of hardened SCGC are significantly improved by incorporating silica fume, especially up to 10wt%. Applying this percentage of silica fume results in 4.3% reduction in the slump flow; however, it increases the compressive strength by 6.9%, tensile strength by 12.8% and flexural strength by 11.5%.

Influence of Fly Ash and Silica Fume on Water-resistant Property of Magnesium Oxychloride Cement

By incorporation of fly ash or silica fume into magnesium oxychloride （MOC） cement, a high water resistance material can be formed for successful industrial applications. The influences of fly ash and silica fume on water-resistant property were investigated by SEM and EDS. It is found that the incorporation of fly ash or silica fume can improve the water-resistance of the MOC. The improvement of the water resistance of the MOC incorporated with fly ash or silica fume may be attributed to the alumino-silicate 5·1·8 gel or silicate 5·1·8 gel.

Preparation and characterization of solidified oleanolic acid–phospholipid complex aiming to improve the dissolution of oleanolic acid

The purpose of this study was to prepare the oleanolic acid–phospholipid complex (OAPC) and then solidify it employing fumed silica by simple solvent evaporation technique to improve dissolution rate of oleanolic acid and oleanolic acid–phospholipid complex. The process of OA-PC was optimized and the type and proportion of fumed silica were studied by dissolution text. The structures of the phospholipid complex and solidified powder were also characterized by differential scanning calorimetry, X-ray diffraction, and scanning electron microscope. In the dissolution tests, OA from solidified powder was further released compared with that from pure OA and OA-PC in different kinds of dissolution media. These results suggest that the method of preparing solidified powder of oleanolic acid–phospholipid complex is suitable for enhancing the dissolution rate of OA and OA-PC.

Analysis of the Damping Behavior and Microstructure of Cement Matrix with Silane-treated Silica Fume

The surface treatment of silca fume with silane coupling agent prior w incorporation in a cement mortar resulted in composites exhibiting increuses in loss tangent by 5%-200% and storage modulus by 10%-20% , relative to the value obtained by using as-received silica fume. The scanning electron microscopy （SEM） images iindicate that there is a morphological difference in the cement paste with treated and as-received silica fume, The, X-ray diffraction （XRD）, infrared （IR） spectrum analyses and mercury intrusion porosimetry （ MIP ） have provided evidence to understand the reaction mechanism between treated silica .fume and the hydrate product of cement. This has led to the establishment of an initial microscopic model describing the damping behavior of cement matrix.