Temperature Control Design with Differential Evolution Based Improved Adaptive-Fuzzy-PID Techniques

This paper presents the design and performance analysis of Differential Evolution(DE)algorithm based Proportional-Integral-Derivative(PID)controller for temperature control of Continuous Stirred Tank Reactor(CSTR)plant in che-mical industries.The proposed work deals about the design of Differential Evolu-tion(DE)algorithm in order to improve the performance of CSTR.In this,the process is controlled by controlling the temperature of the liquid through manip-ulation of the coolantflow rate with the help of modified Model Reference Adap-tive Controller(MRAC).The transient response of temperature process is improved by using PID Controller,Differential Evolution Algorithm based PID and fuzzy based DE controller.Finally,the temperature response is compared with experimental results of CSTR.

DC–DC Converter with Pi Controller for BLDC Motor Fuzzy Drive System

The Brushless DC Motor drive systems are used widely with renewable energy resources.The power converter controlling technique increases the performance by novel techniques and algorithms.Conventional approaches are mostly focused on buck converter,Fuzzy logic control with various switching activity.In this proposed research work,the QPSO(Quantum Particle Swarm Optimization algorithm)is used on the switching state of converter from the generation unit of solar module.Through the duty cycle pulse from optimization function,the MOSFET(Metal-Oxide-Semiconductor Field-Effect Transistor)of the Boost converter gets switched when BLDC(Brushless Direct Current Motor)motor drive system requires power.Voltage Source three phase inverter and Boost converter is controlled by proportional-integral(PI)controller.Based on the BLDC drive,the load utilized from the solar generating module.Experimental results analyzed every module of the proposed grid system,which are solar generation utilizes the irradiance and temperature depends on this the Photovoltaics(PV)power is generated and the QPSO with Duty cycle switching state is determined.The Boost converter module is boost stage based on generation and load is obtained.Single Ended Primary Inductor Converter(SEPIC)and Zeta converter model is compared with the proposed logic;the proposed boost converter achieves the results.Three phase inverter control,PI,and BLDC motor drive results.Thus the proposed grid model is constructed to obtain the better performance results than most recent literatures.Overall design model is done by using MATLAB/Simulink 2020a.

基于Fuzzy-PI的直驱永磁风力发电系统MPPT控制

通过对模糊PI控制算法、MPPT算法分析,并对变流器的控制策略进行推导,提出基于Fuzzy-PI控制策略,确定机侧以转速的偏差及其微分为输入,交轴电流为输出,风机达到最大功率跟踪效果;网侧变流器采用电压外环、电流内环双闭环控制策略。通过Simulink系统仿真,结果表明模糊PI控制系统能实现发电机的最大功率跟踪和单位功率因数运行,控制效果优于传统的PI控制策略。

Nonfragile control for a class of uncertain switching fuzzy time-delay systems

A sufficient condition for the existence of nonfragile state-feedback controllers and a switching law for a class of uncertain switching fuzzy time-delay systems are proposed based on the multiple Lyapunov functions technique, under the assumption that the controller gain to be designed has variations. The corresponding results are all formulated in terms of linear matrix inequalities (LMIs). Simulation results show the effectiveness of the design method.

Self-adaptive fuzzy controller with formulary rule for servo control of discharge gap in Micro EDM

In micro electrical discharge machining （micro EDM）, it is difficult for servo controlling the narrow discharge gap with the characters of non-linear and quick change. In this paper, aiming at solving the problems above, a self-adaptive fuzzy controller with formulary rule （SAFCFR） is presented based on the dual feedbacks composed by gap electric signal and discharge-ratio statistics. To ensure the properties of self-optimizing and fast stabilization, the formulary rule was designed with a tuning factor. In addition, the fast-convergence algorithms were introduced to adjust control target center and output scale factor. In this way, the normal discharge ratio can tend to the highest value during micro-EDM process. Experimental results show that the proposed algorithms are effective in improving the servo-control performance. According to the drilling-micro-EDM experiments, the machining efficiency is improved by 20% through applying SAFCFR. Moreover, SAFCFR is a prompt way to optimize parameters of discharge-gap servo control.

Instantaneous Active and Reactive Power and Current Strategies for Current harmonics cancellation in 3-ph 4wire SHAF With both PI and Fuzzy Controllers

Control strategies for extracting the three-phase reference currents for shunt active power filters are compared, evaluating their performance under different source conditions with PI and Fuzzy Controllers in MATLAB/Simulink environment When the supply voltages are balanced and sinusoidal, the two control strategies are converge to the same compensation characteristics;However, the supply voltages are distorted and/or un-balanced sinusoidal, these control strategies result in different degrees of compensation in harmonics. The compensation capabilities are not equivalent, with p - q control strategy unable to yield an adequate solution when source voltages are not ideal. Extensive simulations are carried out with PI controller and also with Fuzzy controller for both p-q and Id-Iq control strategies under different main voltages. Extensive Simulations are carried out with PI as well as fuzzy controller for both p-q and Id - Iq control strategies by considering different voltage conditions and adequate results were presented. On owing Id - Iq method with fuzzy logic controller gives away an out-standing performance under any voltage conditions (balanced, un-balanced, balanced and non-sinusoidal).

Performance Analysis of PI and Fuzzy Control for Modified LCC Resonant Converter Incorporating Boost Converter

In this paper, the modified LCC type of series-parallel Resonant Converter (RC) was designed and state-space modeling analysis was implemented. In this proposed converter, one leg of full bridge diode rectifier is replaced with Synchronous Rectifier (SR) switches. The proposed LCC converter is controlled using frequency modulation in the nominal state. During hold-up time, the SRswitches control is changed from in-phase to phase-shifted gate signal to obtain high DC voltage conversion ratio. Furthermore, the closed loop PI and fuzzy provide control on the output side without decreasing the switching frequency. The parameter such as conduction loss on primary and secondary side, switching loss, core and copper also reduced. Simultaneously, the efficiency is increased about 94.79 is realized by this scheme. The proposed converter with an input of 40 V is built to produce an output of 235 V with the help of ZVS boost converter [1] even under line and load disturbances. As a comparison, the closed loop fuzzy controller performance is feasible and less sensitive than PI controller.

The Optimized Disign of the Fuzzy Controller(Ⅰ)——The predigested disquisition of rules of fuzzy control

To improve the ability and precisions of the fuzzy control,this thesis points out the adjusted fuzzy control method,realizes the precision of the fuzzy quantity, and reduces the number of the fuzzy control rules,so that it can predigest the process of disigns and realize the methods without influencing the idiocratic control,which are on the base of the domain flexing.

PI control based on fuzzy set-point weighting tracking for hydraulic crane boom system

A PI control strategy based on fuzzy set-point weighting following was proposed for the active damping control of a hydraulic crane boom system （HCBS）. Two valve-controlled PI controllers, which include a proportional feedforward controller based on fuzzy set-point weighting following and a limited semi-integrator（LSI）, are designed respectively. LSI is used to limit output signal and to prevent wind up at the low frequency of the spectrum. By using a range camera and an electronic feedback control, the tip damping on the HCBS can be adjusted artificially. A collaborative control simulation technique of HOPSAN and MATLAB/SIMULINK is applied to the controller design. Simulation results show that the proposed PI control system has less overshoot as well as faster response. The tip damping on the HCBS during operation is improved.

Fuzzy and PI Controller Based SHAF for Mitigation of Current Harmonics with P-Q Method Using Matlab and RTDS Hardware

The main objective of this paper is to develop PI and Fuzzy logic controllers to analyse the performance of instantaneous real active and reactive power (p-q) control strategy for extracting reference currents of shunt active filters under balanced, un-balanced and balanced non-sinusoidal conditions. When the supply voltages are balanced and sinusoidal, then all controllers converge to the same compensation characteristics. However, when the supply voltages are distorted and/or un-balanced sinusoidal, these control strategies result in different degrees of compensation in harmonics. The p-q control strategy with PI controller is unable to yield an adequate solution when source voltages are not ideal. Extensive simulations were carried out;simulations were performed with balance, unbalanced and non sinusoidal conditions. Simulation results validate the dynamic behaviour of Fuzzy logic controller over PI controller. The 3-ph 4-wire SHAF system is also implemented on a Real Time Digital Simulator (RTDS Hardware) to further verify its effectiveness. The detailed simulation and RTDS Hardware results are included.

Design and Stability Analysis of Fuzzy Switched PID Controller for Ship Track-Keeping

The fuzzy switched PID controller which combines fuzzy PD and conventional PI controller is proposed for ship track-keeping autopilot In this paper. By using rudder angle, the whole voyage is divided into two operating regimes which named transient operating regime and steady operating regime respectively. The fuzzy PD controller is employed in transient operating regime for increasing response, reducing overshoot and shorting transition time. And conventional PI controller is used to improve the stable accuracy in steady operating regime. The global controller is achieved by fuzzy blending of all local controllers. Routh stability criterion is utilized to obtain the stability condition of closed-loop system. The simulation results show the effectiveness of proposed method.

Comparative Analysis between Conventional PI, Fuzzy Logic and Artificial Neural Network Based Speed Controllers of Induction Motor with Considering Core Loss and Stray Load Loss

Most of the controllers of IM （induction motor） for industrial applications have been designed based on PI controller without consideration of CL （core loss） and SLL （stray load loss）. To get the precise performances of torque as well as rotor speed and flux, the above mentioned losses should be considered. Conventional PI controller has overshoot effect at the transient period of the speed response curve. On the other hand, fuzzy logic and ANN （artificial neural network） based controllers can minimize the overshoot effect at the transient period because they have the abilities to deal with the nonlinear systems. In this paper, a comparative analysis is done between PI, fuzzy logic and ANN based speed controllers to find the suitable control strategy for IM with consideration of CL and SLL. The simulation analysis is done by using Matlab/Simulink software. The simulation results show that the fuzzy logic based speed controller gives better responses than ANN and conventional PI based speed controllers in terms of rotor speed, electromagnetic torque and rotor flux of IM.

A Novel Asymmetric Three-Phase Cascaded 21 Level Inverter Fed Induction Motor Using Multicarrier PWM with PI and Fuzzy Controller

Multilevel inverters are gaining popularity in high power applications. This paper proposes a new ladder type structure of cascaded three-phase multilevel inverter with reduced number of power semiconductor devices which is used to drive the induction motor. The ultimate aim of the paper is to produce multiple output levels with minimum number of semiconductor devices. This paper uses only 11 switches along with 3 diodes and 4 asymmetrical sources to produce an output voltage of 21 levels. The modulation technique plays a major role in commutation of the switches. Here we implement the multicarrier level shifting pulse width modulation technique to produce the commutation signals for the inverter. The proposed multilevel inverter is used to drive the three-phase induction motor. The mathematical modeling of three-phase induction motor is done using Simulink. Furthermore the PI and fuzzy logic controllers are also used to produce the reference waveform of the level shifting technique which in turn produces the commutation signals of the proposed multilevel converter. The controllers are used to control the speed of the induction motor. The effectiveness of the proposed system is proved with the help of simulation. The simulation is performed in MATLAB/Simulink. From the simulation results, it shows that the proposed multilevel inverter works properly to generate the multilevel output waveform with minimum number of semiconductor devices. The PI and fuzzy logic controller performances are evaluated using the results which indicate that with the help of controllers the harmonics has been reduced and the speed control of induction motor is achieved under different loading conditions.

一种基于模糊规则切换的Fuzzy-PID双模控制器

设计了一种基于偏差和偏差变化率的模糊规则切换Fuzzy-PID双模控制器,避免了传统Fuzzy-PID双模控制阈值切换是由程序自动进行切换,而存在的阈值如何选取及切换扰动等问题.给出了本控制器的控制性能,如鲁棒性、跟踪性和抗干扰能力与PID和常规Fuzzy-PID双模控制的仿真比较.

新型静止无功发生器的Fuzzy-PI控制

论述ASVG的工作原理,根据控制原理设计ASVG的模糊PI(Fuzzy-PI)控制器.采用模糊控制器获得良好的动态性能,同时引入PI控制改善模糊控制器的静态性能,增强其鲁棒性.该控制器使系统在电流跟踪误差较大时比例控制占主导,误差减小速度较快,在误差减小到一定范围内时积分控制占主导,实现稳态无差.并且该控制器具有较强的自适应控制能力,增强了对电力系统稳定性的控制,具有满意的控制精度,易于实现数字控制,比传统的PI控制具有更好的控制效果.数字仿真验证了该控制方法的有效性和正确性.

Fuzzy-PID切换控制在磁流变半主动悬置系统中的应用

建立了一种新型动力总成磁流变悬置的动力学模型,并对其进行动态特性试验。通过数值拟合方法对试验数据进行拟合,得到了电流与可控阻尼力的关系式,为磁流变悬置的控制应用提供了理论模型。考虑车辆悬架系统的等效刚度和阻尼,建立了磁流变半主动悬置系统模型。设计了磁流变半主动悬置Fuzzy-PID切换控制系统,对不同工况下磁流变半主动悬置系统的隔振特性进行了仿真研究,结果表明应用Fuzzy-PID切换控制的磁流变半主动悬置系统具有良好的隔振效果。

Fuzzy-PID复合控制在水泥冷却过程中的应用

针对PID在水泥生产线冷却过程中实际应用所发现的问题,提出了将Fuzzy-PID复合控制算法应用于现场的控制思路,该算法将Fuzzy和PID两种控制方式的控制优点有机结合,根据多次现场实验得到的模糊切换隶属度函数在两种控制方式下自动切换,该控制既能在动态过程中快速调节,又能在稳态过程中准确调节。冷却过程控制软件采用VC++编写,通过在某水泥厂的实际应用表明了该方案的正确性和实用性。

基于Fuzzy-PI双模控制的控制系统

叙述了孵化装置中有关温度与湿度的控制方法。为了提高控制精度、改善系统的动态、稳态性能,引入了基于Fuzzy-PI双模控制方法,并利用Matlab进行仿真。通过仿真和实际运行表明,采用了Fuzzy-PI双模控制以后,加快了动态响应,提高了控制精度,有效地降低了超调量,孵化率达到了规定的技术指标。对于实际中存在的非线性、大滞后、大惯性、难以建立数学模型的系统,采用该控制方法,不失为一种好的策略。

一种基于模糊规则切换的P-FUZZY-PID控制器

针对常规P -FUZZY -PID多模控制切换时存在的问题 ,提出了一种根据偏差和偏差变化率来实现模糊切换的多模控制器。并给出了它的动态性能。

基于fuzzy-PI双模控制的光伏发电系统最大功率点跟踪仿真研究

为了提高太阳电池阵列的工作效率和整个光伏发电系统的稳定性,在光伏发电系统中需要对光伏电池的最大功率点进行跟踪。为了消除常规模糊跟踪算法在最大功率点附近出现的振荡问题,在分析光伏电池伏安特性的基础上,提出了fuzzy-PI双模控制策略,分析了该控制算法的原理,并对控制系统做了设计。Matlab/Simulink仿真表明fuzzy-PI双模控制能够快速、准确地跟踪最大功率点,避免了最大功率点处的振荡,提高了系统稳定性和能量转换效率,从而使整个双模控制兼有了MPPT精确性与快速性。